HMI User Manual - I
Contents
1. HMI Series Panel PC Intel Atom Z Series 3 5 SBC Low Power High Performance Design with Intel Atom Z Series Platform TFT LCD and 10 100 1000 base T Ethernet User Guide Version 1 0 I TECH Tech Company LLC COMPANY TOLL FREE 888 483 2418 EMAIL info iTechLCD com WEB www iTechLCD com FCC Statement This device complies with part 15 FCC rules Operation is subject to the following two conditions e This device may not cause harmful interference e This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a class digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at him own expense N Copyright Notice ALL RIGHTS RESERVED No part of this document may be reproduced copied translated or transmitted in any form or by any means electronic or mechanical for any purpose without the2. L Display to touch screen seal Metal frame housing Mounting screws Customer s front bezel Application 1 Application2 T5x7Sem or 100x 100mm 1 jWALL MOUNTING mount with front bezel and then mounted mount with VESA mount kits into customer spanel and then mounted into wall Applications Application4 ws Z 26 RACK MOUNTING mount with VESA mount kit mount with rack frontbezel and and then mounted with swimming arms then mounted into racks Panel PC Size VESA Mount Dimension 50 75x 75mm gy 75x 75 mm 10 1 75 75 mm 20 4 2 Panel Mount Clip Design Panel is aligned with the same height of the front of open frame metal housing Touch Glass is higher than Open frame metal housing Customers can fix our Panel PC with their fixture max 12mm VESA mount holes are also available for mounting from back side Touch 3 6 mm Panel Front bezei 5mm Standoff Metal frame Mounting Kits Adhesive Transfer Tapes Customers fixture Cut out dimension Custamer s fodre 21 Customer s fixture 5mm front bezel pei Put Panel PC on the fixture wall panel i i Panel Mount from the front with the sides of H 5mm front bezel i the front bezel shown on the outside Side View The Dimension of mounting kits provided customer s fixture Panel mount 6mm Font Bezel Panel PC Size Mountin
3. g kit pes 57 T 4 10 1 8 Finshed KNOWN ISSUES 1 There might be some image noises displayed at the time of PC boot and Windows start up 2 When using an external display as CRT or LCD for external mode Panel amp CRT the resolution of external display may be recommended equal to the CMOS setting for panel Flat Panel Type Lower resolution than CMOS setting in Windows may cause indistinct display Recommendation in CMOS setting I Choose CRT only when use external display Choose Panel only when use internal panel display al H d Default 23 NOTICES 1 Operation Systems we currently support are Windows XP and XP Embedded When installing driver please make sure you re using Windows XP Service Package2 SP2 above 2 The output port for 1931 is only for displaying the same images as built in display The extended mode is not available for 1931 3 When you use CF card as storage of Operation System you need to use Fixed Disk Mode type Compact Flash Card instead of removable disk mode 4 The external Compact Flash socket is NOT A PLUG amp PLAY DEVICE you may remove the CF card only on at POWER OFF status I TECH COMPANY piede eel ien TOLL FREE 888 483 2418 EMAIL info iTechLCD com WEB www iTechLCD com
4. g temperature 0 deg C to 60 deg C Operating Humidity 10 90 Relative humidity non condensing Shock Operating 15G 11ms duration Vibration Operating 5 Hz 500Hz 1Grms 3 Axis Certification CE FCC RoHS 1 3 LCD Selection Guide The HMI series Panel PCs support form 5 7 inch 7 inch 10 1 iinch TFT Panel w touchscreen function please refer the below Size Model Name Resolution Display Color 5 7 ROSI93S IPDIHM 640 x 480 262k 7 051935 2 800 x 480 262k 10 1 WIOI93S IPI IHM 1024 x 600 256k 1 4 HMI Series Brief Size Model Name IO Dimension 1 x Terminal Block Phoenix Type 1 x RS232 5 7 ROSI93S IPDIHM 1 x RS232 422 485 Optional LxHxD 188x148x59mm 2xUSB2 0 1x VGA 1 x 2ch CAN BUS Optional 1 x Terminal Block Phoenix Type 1 RS232 7 WO05I93S IPA2HM 1 x RS232 422 485 Optional LxHxD 218x164 6x60 8mm 2xUSB2 0 1x VGA 1 x2ch CAN BUS Optional 1 x Terminal Block Phoenix Type 1 x RS232 10 17 WIOI93S IPIIHM 1 x RS232 422 485 Optional LxHxD 286x182x60mm 2xUSB2 0 1x VGA 1 x2ch CAN BUS Optional i Chapter 2 Getting Started 2 1 Input Output Devices The following figure shows the I O arrangement of the Panel PC The backside of the chassis contains most of the connectors 7 for example 1 RJ 45 5 RS 232 2 CAN BUS 6 12V DC IN Terminal Block 3 VGA O
5. ices 22 Starting the Panel PC amp O S Installation 2 3 Driver Installation soss Chapter 3 Driver Installation 3 1 Touch Driver Installatio 3 1 1 Configuration Utility 3 2 CAN BUS Driver Installatio 3 3 Brightness Adjustment Chapter 4 HMI series Panel PC Mounting Guide 4 1 VESA Mount 4 2 Panel Mount Clip Design NE 222 9 AO RO SOL Chapter 1 GENERAL INFORMATION 1 1 Introduction The Z5xx series Panel PC is high performance low power PC with Intel USISW XL Chipset combine with a TFT LCD Panel The Intel Core Duo high performance Processor delivers the most performance per watt available in the market The Panel PC is designed to satisfy most of the applications in the industrial market such as POS KIOSK Industrial Automation HMI and Programmable Control System It s a PC based system with DDR2 SDRAM VGA LCD controller one COM ports and on board 10 100 1000 Mpbs Base T Ethernet The Panel PC supports one Mini PCle expansion slot COM port VGA solutions It is a compact design to meet the demanding performance requirements of today s business and industrial applications Modularized Construction Front Touch Screen LOD Panel Mounting Plate S amp C Conposens Rear Cover 1 2 1931 SBC and Atom Z5xx series Panel PC System Specifications CPU Type Intel Atom Z series Proce
6. il us Safety Precautions Warning Caution Always completely disconnect the power cord from your chassis whenever you work with the hardware Do not make connections while the power is on Sensitive electronic components can be damaged by sudden power surges Only experienced electronics personnel should open the PC chassis Always ground yourself to remove any static charge before touching the CPU card Modern electronic devices are very sensitive to static electric charges As a safety precaution use a grounding wrist strap at all times Place all electronic components in a static dissipative surface or static shielded bag when they are not in the chassis and Warranty 10 12 13 gorp mom Please read these safety instructions carefully Please keep this user s manual for later reference Please disconnect this equipment from any AC outlet before cleaning Do not use liquid or spray detergents for cleaning Use a damp cloth For pluggable equipment the power outlet must be installed near the equipment and must be easily accessible Keep this equipment away from humidity Put this equipment on a reliable surface during installation Dropping it or letting it fall could cause damage The openings on the enclosure are for air convection Protect the equipment from overheating DO NOT COVER THE OPENINGS Make sure the voltage of the power source is correct before connecting the equipmen
7. lation DENT 3 3 Brightness Adjustment In our new product 10 1 Panel PC the dimming control has to install drivers and software to work brightness control properly Please do following steps Stepl Installing Driver You can find the driver in the Touch amp Driver CD Find Backlight Control Driver folder and double click the install bat install file Step2 Installing NET Framework 2 0 To install net Framework you have to click the net Framework installation file dotnetfx exe in Framework 2 0 folder for working normally nemi amnia Step3 Installing Backlight Control Software To install Back Light Control Software Click the setup file setup msi Backlight Control Software Folder and Confirm Installation then dimming control enabled by buttons by button at the front bezel Weicome to tho BackLighiContro Setup Wizard 2e S Chapter 4 HMI series Panel PC Mounting Guide The Panel PC is suitable for most of the industrial commercial application by any kind of mounting approach Three main mounting approaches such as VESA Mount Panel Mount IP65 Mount are very easy for user to install the Panel PC As the pictures guided 4 1 VESA Mount Panel is aligned with the same height of the front of open frame metal housing Customers can fix our Panel PC with their own front bezel VESA mount holes are also available for mounting from back side Touch 3mm 6mm PANE
8. prior written permission of the original manufacturer Trademark Acknowledgement Brand and product names are trademarks or registered trademarks of their respective owners Disclaimer We reserve the right to make changes without notice to any product including circuits and or software described or contained in this manual in order to improve design and or performance We assume no responsibility or liability for the use of the described product s conveys no license or title under any patent copyright or masks work rights to these products and makes no representations or warranties that these products are free from patent copyright or mask work right infringement unless otherwise specified Applications that are described in this manual are for illustration purposes only We make no representation or warranty that such application will be suitable for the specified use without further testing or modification Warranty We warrant that each of its products will be free from material and workmanship defects for a period of one year from the invoice date If the customer discovers a defect We will at its option repair or replace the defective product at no charge to the customer provided it is returned during the warranty period of one year with transportation charges prepaid The returned product must be properly packaged in it s original packaging to obtain warranty service If the serial number and the product shipping data diffe
9. r by over 30 days the in warranty service will be made according to the shipping date In the serial numbers the third and fourth two digits give the year of manufacture and the fifth digit means the month e g with A for October B for November and C for December For example the serial number 1W07Axxxxxxxx means October of year 2007 Check List Before using this BOX PC please make sure that all the items listed below are present in your package 1 x HMI Series PPC unit 1 x Driver Utility CD 1 x HMI User Guide 1 x 1931 User Manual VVVV Make sure that all of the items listed above are present Do not attempt to apply power to the system if there is damage to any of its components Customer Service We provide service guide for any problem as follow steps First contact with your distributor sales representative or our customer service center for technical support if you need additional assistance You may have the following information ready before you call gt Product serial number gt Peripheral attachments gt Software OS version application software etc gt Description of complete problem gt exact wording of any error messages In addition free technical support is available from our engineers every business day We are always ready to give advice on application requirements or specific information on the installation and operation of any of our products Please do not hesitate to call or e ma
10. ries default is Premier Touch The touchscreen system consists of a touchscreen and an electronic touchscreen controller The attached Driver CD contains drivers of the touch panel controller Follow the steps as below to install TouchKit Stepl Put the TouchKit CD to CD ROM Step2 Open the Win2000_XP directory Step3 Double click the Setup exe then system starts to run the installation program Notice Do not plug the USB controller on the system before the installation has been finished Step 4 Click Next to continue installation And it will auto detect touch devices in COM2 port at your Panel PC Tha mai Tauck pL umo Seno prog Step 5 Following the step by step to finish the driver installation 3 1 1 Configuration Utility After finishing the installation please follow the steps to test the configuration utility Step 1 Click the TouchKit shortcut function in the desktop Step 2 Enter General function and choose the language you need Step 3 Correct 4 point locations on screen with the Panel Screen display as follows Step 4 Play Yes to continue if 4 points calibration test is fine and finish the test 3 2 CAN BUS Driver Installation HMI Series support 2 channels CAN BUS L1 H2 L2 Stepl Enter CAN BUS floder Install dotnetfx2 0 exe first a D mar e aep 17 Step2 Enter CAN BUS Folder Install setup msi Then finish the instal
11. ssor CPU Speed 1 1GHz 1 6GHz CPU FSB 533MHz Chipset Intel US15W BIOS AMI 4M Flash VGA Intel 500 Integrated Graphics Engine LVDS Intel GMA500 Integrated Graphics Engine built in 24 bits single channel panel support up to UXGA panel resolution LAN 2 x Giga LAN Realtek RTL8111B Realtek RTL8111B Giga LAN Controller Memory Type 1 x SO DIMM socket supports up to 2GB SO DIMM 400 533 SDRAM Winbond W83627EHG integrated hardware monitoring IDE Interface One channels supports Ultra DMA 33 66 100 Sound Realtek ALC888 GR Line out Line in amp Mic in USB 6 ports USB 2 0 2 x USB Connector 4 x USB pin header 1 x DC IN Jack 1 x VGA out connector Edge Connectors 2 x Gigabit LAN RJ 45 1 x Dual USB stack connector 1 x RS232 Com Port 1x44 pins IDE box header 1 x 10pins pin header for Front Panel 2x5 1 x 2pins pin header for 5V 12V external power 1x 12pins pin header for Front Audio 2x6 1 x 8pins pin header for USB 3 4 5 6 2X4 E 1 x 10pins Digital l O 2x5 Connectors 2 x 10pins pin header for COM 3 4 RS232 2X5 1 x 5pins pin header for COM3 RS422 485 1 x 4pins ATX 12V connector 1 x 20pins DF13 20DP Connector for LVDS 1 x 3pins digital panel backlight brightness controller 1 x 7pins digital panel inverter Power Connector Input 4 pin ATX 12V Power input Expansion Slots 2 x Mini PCle 1 for IDE SSD Form Factor 3 5 inch Dimensions 146mm x 101mm Mechanical amp environmental Operatin
12. t to the power outlet Position the power cord so that people cannot step on it Do not place anything over the power cord cautions and warnings on the equipment should be noted If the equipment is not used for a long time disconnect it from the power source to avoid damage by transient over voltage Never pour any liquid into an opening This could cause fire or electrical shock Never open the equipment For safety reasons only qualified service personnel should open the equipment If any of the following situations arises get the equipment checked by service personnel The power cord or plug is damaged Liquid has penetrated into the equipment The equipment has been exposed to moisture The equipment does not work well or you cannot get it to work according to the user s manual The equipment has been dropped and damaged The equipment has obvious signs of breakage 15 not leave this equipment in an uncontrolled environment where the storage temperature is below 20 C 4 F or above 60 C 140 F It may damage the equipment Revision History Version Date Note Author 0 8 2010 9 8 Y First Version Cage Hsu 1 0 2010 9 21 Y Revise Brightness Control Cage Hsu Chapter 1 GENERAL INFORMATION Contents 1 1 Introduction 1 2 1931 SBC and Atom Z5xx series Panel PC System Specification 1 3 LCD Selection Guide 1 4 HMI Series Brief Chapter 2 Getting Started 2 1 Input Output Dev
13. ut Phenix Type 4 USB T RS 232 422 485 1 RJ 45 2 x RJ45 10 100 1000 2 VGA 1 x VGA D Sub 15 Female 3 CAN BUS Optional 1 x 2channel CAN BUS chi ch2 4 USB 2xUSB2 0 5 RS 232 1 x RS232 D Sub 9p 6 DC in 1 x 12V DC in with Terminal Block Phoenix Type G 7 RS 232 422 485 1 x RS 232 422 485 D Sub 9p Default RS 232 2 2 Starting the Panel PC amp O S Installation 1 Connect the power to 12V DC power supply to 3 pins Terminal block Phoenix Type Terminal Block Male Part Terminal Block Female Part Connect to rminal block on 2 Pressthe power on switch to start the Panel PC 3 Press DEL to enter CMOS setting and check the BIOS setup 4 You may install your own O S if it is not installed When installing O S for this Panel PC please follow the steps and use external equipment as Keyboard and USB DVD ROM a Please use external USB DVD ROM to run the O S and Driver setting as picture showed below 2 3 Driver Installation The PPC comes with 1931 User s Manual and Driver CD that contains most of the drivers and utilities of your needs a Following the step by step to install Driver Please refer 1931 SBC User s Manual Chapter 3 4 5 6 include Chipset VGA Audio and Ethernet b Following the step by step to install the Touch screen if necessary Please refer S series PPC User Guide Chapter 3 Chapter 3 Driver Installation 3 1 Touch Driver Installation HMI se
Download Pdf Manuals
Related Search