User Manual
Contents
1. VisionSystems Safe T Scope 7 Rearview Backup Camera System INSTALLATION USER S MANUAL STSK7565 90 21 144th Place Jamaica NY 11435 1 800 227 2095 www roscovision com WARNING 1 To preventelectrical shock DO NOT OPEN THE MONITOR CASE There are dangerous voltages inside the monitor There are no user serviceable parts inside 2 Avoid exposing monitor to water rain moisture etc It is NOT waterproof Any moisture inside the monitor could cause extensive damage 3 Do disassemble the camera or the monitor This voids the warranty Disassembling the camera will compromise the waterproof seal e STORAGE 1 Do not expose the monitor to excessive heat or cold The storage temperature of this machine is 13 158 F and operating temperature is 5 149 F 2 Do not store or operate in humid environments 9 GENERAL 1 This system is intended for use in automotive applications Power source should be an automobile storage battery 12V 24V 2 Make sure all cables are connected properly Improper cable connections may damage the monitor Remove the cable connection when you do not intended to use the unit for a long period of time Please install this system according to the instructions in this manual Connect the system to an ignition switched power source Connection to an unswitched battery source will reduce battery life pd This device complies with Part 15 of the FCC Rules Ope2. 9165 3 7 x 2 7 x 3 4in 95 x 70 x 86mm COLOR TFT LCD 70 TOP 50 DOWN 70 LEFT RIGHT 6W 500mA MAXIMUM 12 32Vdc NTSC COMPOSITE VIDEO SINGLE 1VP P 75 OHM 800 H x 480 V 500 1 300cd m2 5 F to 149 F 20 C to 65 C 13 F to 158 F 25 C to 70 C 0 4Kg 0 915 7 2 x 5 x lin 183 x 127 x 26mm The use of the STSK7565 Vehicle CCTV system should not in any way be used as a substitute for careful and cautious driving Always obey traffic laws and motor safety regulations must always be adhered to opecifications subject to change without any notice Fig 1 Camera mount in suggested location Mount camera assembly high Centered Camera mounting hole pattern 60 60 THRU Position of camera Vehicles behind truck Street Rear Bumper Typical monitor image of view from properly installed camera 11 Fig 3 Optional wind deflector x A I ii a an pF n um Gi mmm Fig 4 Back of Bracket if Front of Bracket 12 Fig 5 Mounting on the dash console etc Fig 6 13 POWER INPUT LEAD RED To Ignition Switched Accessory iH GROUND WIRE BLACK To metal point of the vehicle Filter CAM2 CAM2 REVERSE Trigger WHITE amp EEgd lr Reverse REVERSE Trigge
3. ct the red wire to an ignition switched accessory ex radio power source and connect the black wire to chassis ground See wiring diagram for connections See Fig 7 2 The monitor terminates in a 13 pin connector which should be connected to the mating 13 pin receptacle end of the power video audio distribution harness When connecting the cables check to make sure to match the directions of the arrows on the 13 pin connectors male to female 3 For typical rear view installation connect the camera extension cable from the rear view camera to the harnesses connector marked REVERSE 4 For multi camera installations be sure to mark each extension cable properly and connect to the appropriate harness connector marked C1 or C2 Bundle excess cable together using a cable tie or electrical tape 5 The green wire is the REVERSE trigger wire In typical rear view installations connecting this wire to the vehicle s backup light circuit will activate the rear view image whenever the vehicle shifts into reverse 6 Camera Drill a 13mm 0 5in diameter hole into vehicle body near the camera and bracket Insert camera cable into vehicle be careful not to kink cable and fit grommet into hole Apply sealant around grommet to increase resistance to water penetration Connect camera to the camera extension cable which runs inside the vehicle 7 Feed as much cable as possible into vehicle and clamp securely This reduces the possibility of it b
4. e lower area of the vehicle e g bumper This reduces the view of the camera and increases the chance of physical damage to the camera 3 Attach camera to bracket using screws provided Adjust angle as indicated in Fig 2 Use rear bumper and back of vehicle as a reference point 4 Wind deflector may be installed This deflector is designed to reduce the buildup of dust dirt and moisture on the camera lens See Fig 3 STSM250 MONITOR 1 Attach monitor inside vehicle in a location convenient to the driver e g center of dash overhead or flush mounted in dash 2 Attach the bracket of choice to the dashboard or to the headliner using self tapping screws and or adhesive pad 3 Fasten monitor to bracket and adjust mounting angle to allow optimum driver viewing comfort See Fig 4 STSH320 CAMERA EXTENSION CABLE 1 The camera to cable connection is waterproof Be sure to position the cable properly The male end attaches to the camera The female end attaches to the power video audio distribution harness typically located under the dashboard See Fig 5 IMPORTANT For typical rear view installation the rear camera MUST be connected to the power harness at the connector marked REVERSE 2 Do notrun the cable over sharp edges or corners Do not kink the cable Keep the cable away from hot and rotating parts 3 Fasten all cable runs and secure all excess cable WIRING CAMERA AND MONITOR 1 Monitor Conne
5. eing hooked or snagged 8 Keep all cables away from HOT ROTATING and ELECTRICALLY NOISY components 9 FUEL TANKERS amp OTHER SPECIALTY VEHICLES All electrical equipment fitted to petroleum vehicles must be connected via battery master switch and must be isolated from the battery while the vehicle is loading and unloading For other specialty vehicles please check applicable code and regulations prior to installation 10 Always consult your dealer when fitting an electrical or electronic equipment to a vehicle fitted with a CAN bus or multiplex system IMPORTANT For installations requiring multiple cameras or for installations not requiring typical rear view images please refer to the wiring diagram Fig 7 and the particu lar vehicle s electrical schematic for selection of proper power and trigger connection points FUNCTIONS AND OPERATION MONITOR 1 POWER When the ignition is switched on the monitor will be in standby mode steady red light no image will be on the screen waiting for trigger signal When a trigger wire is energized by 12v power steady green light such as backup lights turning on the image captured by the selected camera will appear on the monitor Pressing the power switch will change the monitor status from standby to steady on Steady on mode status will show camera view depending on user selection Volume Adjust Speaker Volume These buttons are also used to adjust the value
6. ht times to set CAM2 Press to select Normal Mirror mode Wait 3 seconds to exit setup mode Press the MENU button nine times to set Vertical Press to flip image Wait 3 seconds to exit setup mode Press the MENU button ten times to set Dimmer Press to select Auto Day Night Wait 3 seconds to exit setup mode Press the MENU button eleven times to set Scale Press to select On Off Wait 3 seconds to exit setup mode Press the MENU button twelve times to set Scale Adjustment Press to change selected line Press to adjust position of line Wait 3 seconds to exit setup mode SPECIFICATIONS STSC150 CAMERA PICK UP DEVICE TV SYSTEM PICTURE ELEMENTS SENSING AREA IMAGE SIZE SYNCHRONIZATION HORIZONTAL RESOLUTION REQUIRED ILLUMINATION SIGNAL TO NOISE RATIO POWER SUPPLY POWER CONSUMPTION CURRENT CONSUMPTION LENS ANGLE OPERATION TEMPERATURE STORAGE TEMPERATURE WEIGHT DIMENSIONS W x H x D STSM250 MONITOR SCREEN 7 0 inch ANGLE POWER CONSUMPTION POWER SOURCE TV SYSTEM VIDEO INPUT OUTPUT RESOLUTION CONTRAST BRIGHTNESS OPERATING TEMPERATURE STORAGE TEMPERATURE WEIGHT OUTER DIMENSIONS WxHxD DISCLAIMER CMOS NTSC 626 H x 586 V NTSC 4 08mm x 3 1mm 1 4 inch INTERNAL 420 TV LINES 0 5 LUX MINIMUM F 1 2 MINIMUM 48dB AT AGC OFF 12Vdc 1 8W AT 12Vdc MAX 120mA 110 D 88 H 66 V 5 F to 158 F 20 C to 70 C 40 F to 176 F 40 C to 80 C 0 4Kg 0
7. r GREEN Note For typical single Camera installation this trigger wire should be connected to the vehicle s back up lights circuit and the rear view camera should be attached to the connector marked REVERSE 14 VisionSystems 90 21 144th Place Jamaica NY 11435 WWW roscovision com Ph 1 800 227 2095 Fx 1 718 297 0323 A ISO 9001 200 78496 Century of QS 9000 March 1998 FM 78495 Printed in China Automotive Safety Lit P N 04242012
8. ration is C subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation 1 3 1 High voltages exist within the monitor Opening of monitor case is unsafe and never necessary for operating purposes In case of any failure please tum off the display at once and notify our company or the corresponding dealer The monitor is made up of many precise electronic components Any disassembly or modification may lead to damage and voiding of warranty 1 C1 G2 Switch from camera 1 to camera 2 2 Reduce the volume or adjust setting lower 3 Menu Access and exit the display menu 4 Increase the volume or adjust the menu setting higher 5 Light sensor 6 RediGreen light H will be red when in stand by state and will be green when working T Power Turn the system on off COLOR BACKUP CAMERA SYSTEM STSK7565 INTRODUCTION Please read this manual thoroughly This manual contains instructions to make the installation of the camera and monitor easier The color backup camera system is a supplement to standard rear view mirror systems and will provide additional rear view vision when installed and maintained properly It is not intended in any way to be a substitute for careful and cautious driving All applicable traffic laws and motor vehicle safety regula
9. s within selected setting of menu option MENU Button See p 8 Press the MENU bottom to open on screen options Press Menu to cycle through choices and to change your settings C1 C2 Switches from Camera 1 to Camera 2 and vice versa NOTE The reverse camera C2 has selectable back up grid when triggered HOW TO SET YOUR MONITOR TO YOUR REQUIREMENTS NOTE On screen menu commands should only be selected when monitor is in Steady on green light mode Never change settings while operating vehicle Press the MENU button once to set desired brightness Press to increase reduce the brightness Wait 3 seconds to exit setup mode Press the MENU button twice to set desired contrast Press to increase reduce the contrast Wait 3 seconds to exit setup mode Press the MENU button three times to set desired color Press to increase reduce the color Wait 3 seconds to exit setup mode Press the MENU button four times to set desired tint Press to increase reduce the tint Wait 3 seconds to exit setup mode Press the MENU button five times to set desired language Press to select English French Spanish Wait 3 seconds to exit setup mode Press the MENU button six times to reset Press to restore factory defaults Wait 3 seconds to exit setup mode Press the MENU button seven times to set CAM1 Press to select Normal Mirror mode Wait 3 seconds to exit setup mode Press the MENU button eig
10. tions must still be obeyed FEATURES STSC150 CAMERA 360 000 pixel image sensor 0 5 Lux sensitivity 18 IR LED Auto White Balance AWB Field of view 110 Diagonal e Back Light Compensation BLC Automatic electronic iris provides a clearer more consistent image in low and bright light Compact and lightweight design installs easily into most vehicles e Waterproof dustproof IP69K rating e Wind deflector reduces buildup of dirt on lens STSM250 TFT LCD COLOR 7 MONITOR e Menu button for Picture System and Options Backlit buttons Camera 1 Camera 2 Auto dim e Power stand by switch Built in speaker CONTENTS OF COMPLETE SYSTEM 1 Camera with Accessories Mounting Bracket w hardware Wind Deflector 65 Camera extension cable 1 Monitor with Accessories Sunshield Duckfoot universal bracket for surface mounting of monitor on dashboard or headliner including adhesive pad Power Video Audio Distribution harness with reverse trigger U Bracket IMPORTANT For typical rear view installation the rear camera MUST be connected to the power harness at the connector marked REVERSE Note The following instructions are for typical rear view application STSC150 CAMERA 1 Attach camera bracket close to rear marker lights centered on vehicle see Fig 1 Attachment point must be sturdy enough to support camera and bracket 2 We do not recommend mounting the camera near th
Download Pdf Manuals
Related Search