Soldering Station SOLDERING STATION
Contents
1. 2064549 2062627 SOLDERING STATION Thermo Control Anti Static User s Manual www element14 com m co uk www mcmelectronics com Page lt 1 gt 01 06 12 V1 1 Soldering Station User s Manual TEMMA Thank you for purchasing the TENMA Soldering station Please read this manual before operating the equipment Keep manual in accessible place for future reference m Warning Temperature of iron tip will be up to 200 C to 400 C after connecting power so it may lead to injury of fire because of improper usage Please abide the following terms Don t touch the iron tip or surrounding metals Never operate it near the flammable gas or substance Disconnect from power source if the unit will not be used for long periods Switch off power during short breaks Replace accessories or iron tip after turning off the station and let it cool down Never operate this device if you don t have soldering experience or enough knowledge to use Keep away from children m Safety Precautions Caution Improper usage can cause serious injury to personnel and or damage to equipment For personnel safety please follow this precautions Never use it to do other work except soldering Do not subject the main unit to physical shock Never drop or sharply jolt the unit Don t change the device at will Replace loss items with original accessories of TENMA Don t put it in water or operate with wet hands Don t pull the cable but hold tightly the p2. replaces all data sheets previously supplied The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness any error in or omission from it or for any use made of it Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted Liability for loss or damage resulting from any reliance on the Information or use of it including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising is excluded This will not operate to limit or restrict the Group s liability for death or personal injury resulting from its negligence www newark com Tenma is the registered trademark of the Group Premier Farnell plc 2012 I EMNMA www cpc co uk www mcmelectronics com Page lt 8 gt 01 06 12 V1 1 www element14 com www farnell com
3. Changing Soldering Tip www element14 com www farnell com www newark com Always turn the power OFF when removing or inserting a tip Let the tip to cool down to room temperature before holding it with heat resistant pads Unscrew the metal cap nut 1 Pull out the shaft of the soldering iron 2 Replace it with a new soldering tip Put back the shaft and securely lock with the metal cap nut TENMA Www cpc co uk www mcmelectronics com Page lt gt 01 06 12 V1 1 Soldering Station User s Manual TEMMA 21 10140 21 10150 0 C 10 C 18 F 21 10142 21 10152 0 C 0 c 21 10144 21 10154 o L e 0 C 0 5 0 029 0 C 21 10146 21 10156 OF y m 0 C 0 4 0 02 orc 21 10148 R05 0 02 21 10158 Ro 2 0 006 a Sai 0 C 1 0 C g 8 F 17 U G4 Tip out diameter 06 5 All tips sold separately Dimensions Millimetres Inches Part Number Table Tip Chisel Angled 4 0mm PK 10 21 10156 Tip Conical Micro 0 2mm PK 10 21 10158 Heating Element 60W AT938D AT60D CBB018722 Important Notice This data sheet and its contents the Information belong to the members of the Premier Farnell group of companies the Group or are licensed to it No licence is granted for the use of it other than for information purposes in connection with the products to which it relates No licence of any intellectual property rights is granted The Information is subject to change without notice and
4. ERP T A ek mea d am i SET r m C l T H C a REAL T _ ts at it d tl 20g 300 DO a 300 6400 COC T oe e e eee eee M a lel elle ee ol T m e e e e e e a o Oo l a a l l i l 1 l l i I i www element14 com diagram diagram 2 www farnell com www newark com er TENMA www mcmelectronics com Page lt 4 gt 01 06 12 V1 1 Soldering Station User s Manual TEMMA 3 Adjusting temperature Under normal working condition pressing and holding button A or A you can either increase or decrease the temperature quickly Keeping the knob in pressed will adjust the temperature setting quickly short pressing knob you can adjust temp step by step The display screen shows the temperature value simultaneously Release knob for 3s to store Diagram 3 Temp adjustment status Se ee Se Se Se ee er ee er ee hl el el er er lc ee a Se Se i i I i i 7 l l i _ il l I i i T diagram 3 4 Quickly adjusting temperature 4 1 Under working condition you can set working temperature quickly by programmable buttons Press the button once to extract setting temperature stored in button 1 2 amp 3 this way you can easily set the working temperature 4 3 Temperature hot key A Hot key 1 is usually applied to store a 200 C or lower temperature value at w
5. bration Temperature REAL em am Tapen unit co LIC will Soe 685 888 a Power direction Display of status Se a _ a Memory temp Memory temp 2 Memory temp 3 Features e New appearance design big LCD screen for clear and convenient reading e PID power control loop with constant temperature set by MCU computer for more precision temperature control e Imported temperature beard materials with long life e Itis convenient that the device adopt three programmable knobs in different condition e Display the temperature between Fahrenheit and Celsius flexibly convenient for the type of operators e Computerized temperature calibration can correct the difference between the actual and display temperature quickly e Heating element malfunction alert Operating Guidelines Please refer to the Control Panel Guide section for buttons and display panel details 1 Connection 1 1 Insert soldering iron s plug into the socket and tighten the nut on the plug securely and place it in iron holder 1 2 Inset station s power cord into power plug on the back panel and plug the cord into a power source 2 Power on 2 1 Turn on the unit 2 2 The Digital display will initially display the current set temperature the value of last time using for 3 seconds After few seconds it would display the actual temperature with temp unit C or F Diagram 1 Diagram 2 turn on station heating station ia ii SRT gt ea MOE aR
6. d on the screen there is some wrong in heating element or the circuit Diagram 5 6 Turn off the unit and follow the instructions to replace the heating element a a a a SSS a a l REAL H E tll 200 300 400 I ee Al m gt Eg 5 mv diagram diagram 6 www element14 com TM www farnell com www newark com www cpc co uk www mcmelectronics com Page lt 6 gt 01 06 12 V1 1 Soldering Station User s Manual TEMMA Replacing the heating element Note Diagram 7 is soldering station 21 10115 heating element resistance about 8Q to 10Q CON OOF WN gt Power off the unit and unplug the device Wait for the heating element to cool down Loosen the nut 1 Remove the tip retainer 2 and soldering tip 3 Unscrew heating contact 4 remove grouping spring 5 Remove the full heat wire group 6 Please reference to diagram Section 7 Replace the old one the good condition heating element Reverse the process to secure the heating element in the handle 938D diagram 7 Care and Maintenance Keep the soldering station dry If it gets wet dry it immediately Use the soldering station only in normal temperature environments Keep the soldering station away from dust and dirt The soldering iron tip should be cleaned after use by wiping it on the damp sponge found in the soldering iron stand This is to get rid of burnt solder or fluxes that cause oxidation on the tip
7. hich level machine stands by and on rest B Hot key 2 is a shortcut of temperature between 300 C to 350 C at which level a general soldering job can be done C Hot key 3 is a fast channel to high temperature of 380 C specified of special welding job www element14 com TM www farnell com www newark com www cpc co uk www mcmelectronics com Page lt 5 gt 01 06 12 V1 1 Soldering Station User s Manual TEMMA 5 Temperature calibration You need calibrate the temperature of tip after you replace with a new heating element or tip 5 1 Enter into calibrating station by long pressing knob x gt 3s 5 2 You can directly adjust the value of calibration by pressing knob A or Y 5 3 The value of calibration is temperature measure minus the setting e g Actual value 380 C Setting value 350 C 30 C Pressing knob A adds 30 C Actual value 320 C Setting value 350 C 30 C Pressing knob W minus 30 C 5 4 The calibrating temp range is 50 C to 50 C 5 5 You can press knob x to store after you finish calibration Diagram 4 Temp correction status ee ee ee Aan co La 200 300 400 T e e eee ee ae diagram 4 6 Temp unit exchange In the power off condition press and hold knob then turn on the station the temp unit will be changed between C and F and store automatically 7 False alarm When H E or S E is displaye
8. lug when you take it out of plug Please keep the operate place well ventilated since soldering process produce smoke Don t play with other people or would be easy to hurt others or yourself a What s Included Device 1 PC Soldering Iron 1 Set lron Holder 1 PC Power Cord 1 PC Manual 1 Copy Clean Sponge 1 PC www element14 com www farnell com www newark com Www cpc co uk www mcmelectronics com Page lt 2 gt TENMA 01 06 12 V1 1 Soldering Station User s Manual Specifications Controlling Range 302 F to 842 F Temperature Stability 1 C Static LCD Max Surrounding 40 C Temperature Calibrating Method Digital Calibration Temperature Range 50 C to 50 C for Calibration 122 F to 58 F Heating Element 2 Cores TENMA Specifications are subject to change without prior notice Heating Element 77 Heating core line SE i 2 Cores TENMA Control Panel Guide Handle Temperature Led Display Screen Soldering Iron Holder You J D D oo o Temperature Control And Operations Button _ Cleaning Sponge Socket www element14 com www farnell com www newark com Www cpc co uk www mcmelectronics com Page lt 3 gt TENMA 01 06 12 V1 1 Soldering Station User s Manual TEMMA Introduction for LCD Display petting i and display Display of status a 2 SET Set Temperature ewww weet ee ee ee eee REAL Real Temperature SET T m C C a CAL Cali
Download Pdf Manuals
Related Search