Model iH6 The Home System For Your iPod
Contents
1. Battery The iH6 uses a backup battery system to provide continuous alarm operation and clock settings in the event of a power failure If the Battery Low Icon located on the left of the display is flashing itis time to replace the backup batteries Please make sure the AC adaptor is connected otherwise all settings may be lost during battery replacement Open the battery compartment cover located on the bottom of the unit Insert 2 AA batteries as indicated We recommend the use of alkaline batteries for longer life Batteries information Do not mix old and new batteries Do not mix alkaline standard carbon zinc or rechargeable nickel cadmium batteries Using The Remote Control Unit The Remote Control controls basic functions on the H6 and certain iPod functions when the iPod is docked in the H6 For best results use the remote control within 12 feet of the unit Skip to previous or next track when 4 Button iPod is playing or HOLD to scan i current playing track In radio mode press to tune stations HOLD to scan radio stations Volume Button Lowers volume level Volume Button Raises volume level EQ Button Set Treble Bass and Balance settings for best sound Turns iH6 ON or OFF Power On Off Alarm or reset alarm when Reset Button alarm is sounding Selects iPod and iPod Play Pause Button plays track In play mode press to pause2. To play 2nd Gen shuffle set Shuffle Mode Switch to Play Turn on shuffle press iPod button on the iH6 and press play on your shuffle To play 1st Gen shuffle connect audio patch cord from shuffle headphone out jack to H6 line in jack Note Please don t charge and play 1st Gen shuffle at the same time this will create interference noise d see steps c and d under Playing and Charging your iPod for adjusting volume and EQ Do not play iPod and shuffle or line in source at the same time e To turn shuffle off use shuffle controls Note If you dock an iPod with a drained battery it may take up to 6 minutes of charging before the iPod will respond Radio Setting up Antennas a Snap AM loop antenna into provided stand then plug AM antenna cable into AM Loop Antenna socket on back of unit Move antenna 12 away from unit for best reception b Extend FM Antenna on back of unit fully for best reception Do not strip alter or attach to other antennas Tuning and Playing the Radio a Press the Radio Button to select radio play mode Press as needed to select AM FM1 or FM2 radio band b Turn the Set Wheel to tune radio to a desired station c To memorize the current station as a preset press and hold Preset Button 1 2 3 or 4 Repeat steps a b and c to preset up to 12 stations 4 AM 8 FM To listen to a preset station at any time simply press the desired preset button d Turn the Volume Wheel to adjust iH6 volu
3. and disconnect the antenna or cable system during a lightning storm or when it is left unattended and unused for long periods of time This will prevent damage to the product due to lightning and power line surges Overloading Do not overload wall sockets extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock Damage Requiring Service The unit should be serviced by qualified service personnel when A the power supply cable or plug has been damaged B objects have fallen into or liquid has been spilled into the enclosure C the unit has been exposed to rain D theunit has been dropped or the enclosure damaged E the unit exhibits a marked change in performance or does not operate normally Antenna Do not connect an external antenna to the unit other than that provided Periods of Nonuse If the unit is to be left unused for an extended period of time such as a month or longer the power cable should be unplugged from the unit to prevent damage or corrosion Servicing The user should not attempt to service the unit beyond those methods described in the user s operating instructions Service methods not covered in the operating instructions should be referred to qualified service personnel Questions Visit www ihomeaudio com Troubleshooting Symptom Possible Problem iH6 does not turn on AC adaptor isn t plugged into a working wall socket Plug the AC adaptor into a wo
4. del encastre El iPod est trabado no El iPod est trabado no responde Por favor aseg rese de que su iPod funcione correctamente antes La bater a del iPod podr a tener alg n de colocarlo en encastre Refi rase al manual de su iPod para inconveniente y LabandadeAMno La antena no est ubicada correctamente Aleje la antena de la unidad y g rela para mejorar la recepci n suena pero las dem s s El sonido sale El volumen se encuentra muy alto Baje el volumen distorsionado El sonido sale distorsionado de la unidad Si el sonido original de su iPod era de pobre calidad las distorsiones y ruidos se har n m s notables con los parlantes de alta potencia Pruebe utilizar otra fuente de audio como un CD Si est utilizando un iPod de primeras generaciones o un Shuffle intente bajar el volumen de su aparato Tambi n intente apagar el amplificador de bajos El control remoto Las bater as est n gastadas Reemplace las bater as por nuevas no funciona TET A A r No est apuntando el control remoto hacia el Apunte el control remoto hacia el iH6 y mant ngase a una distancia iH6 m xima de 10 pies de la unidad 9 Solucionando problemas La unidad recalienta Esto es normal Apague la unidad o baje el volumen luego de largos per odos de uso a alto volumen No puede La l nea de salida no est dise ada para La se al de salida require amplificaci n Utilice parlantes u otra escuuchar los auriculares Los parlantes n
5. press again to select AM FM band Turn the Set Wheel to tune in a station Press and hold a preset button 1 2 3 or 4 to save the station as a preset Controls and Indicators Dock Sleep Button 3 Shuffle USB Port Preset Buttons ina Radio AM FM1 FM2Button Q Volume Wheel Set Wheel Caer Es gt iPod Button A set D EQ Button B Alarm Reset Power Off Button Alarm On Off Button Alarm 1 Button Alarm 2 Button 9 Time Zone Button D DST switch AC Adaptor Jack B Line in Jack Shuffle Mode Switch D FM Antenna AM Loop Antenna socket D iH6 Display Sleep Display Time Display PM Indicator Alarm 1 Alarm 2 Indicators Battery Low Indicator Volume Idicator I AM FM1 FM2 Indicator Alarm Time PM Indicator Daylight Saving Time Indicator iPod Indicator Radio Frequency Alarm Time Display 2 Using the iH6 Connect iH6 to Power Source a Plug the AC adaptor cable into the AC Adaptor Jack and the other end into a standard 120v wall socket Adaptor must be plugged in to operate The H6 does not operate on batteries Setting the Clock a Press and hold the 9 Time Zone Button until the display flashes b Turn the Set Wheel to select your time zone c Press the Time Zone Button again The clock will display the current time in your time zone d To adjust the time for Daylight Saving T
6. product to the Factory Service Center and its return to the owner This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original purchaser In no event will SDI Technologies or any of its affiliates contractors resellers their officers directors shareholders members or agents be liable to you or any third party for any consequential or incidental damages any lost profits actual exemplary or punitive damages Some states do not allow limitations on implied warranties or exclusion of Consequential damages so these restrictions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Your acknowledgment and ee to fully and Completely abide by the above mentioned disclaimer of warranty is contractuall binding to you upon your transfer of currency money order cashier s check or credit card for purchase of your SDI Technologies produc Questions Visit www ihomeaudio com For operating instructions 1 877 ihome01 1 877 446 6301 Toll Free For any other questions 1 800 288 2792 Toll Free iH6USBIB 080106 C Printed in China
7. Model H6 o For Your iPod WARNING The iH6 shuffle port is ONLY for use with an iPod shuffle DO NOT connect any other device such as iPod or iPhone to this port as doing so can cause damage to the iH6 iPod iPhone or both EE ph E hi Sete EEEEEERERERER gt PEER ES A el es Choke ON EEE EEE EEE EEES A a Shhh ee teh ee Shh rr AAA pell EEEEEEEEEEEE EEREEREEREREREREREREE Eee EE ELS OMM M MON EREEEERERERERERERERE FER ehhh hs EEEEEREREEREREREREREE E EERERERERERERE E EE EFE EE UU M e EERERERERERERE eh GUN M EFE EE EE EFE EE EFE EE EE tr E AEREA EFE EFE E GUMMI EE EE EE GUI Db EFE EFE Db bk A AAA AAA AAA AEREA AE NOTE THIS UNIT WILL NOT CONTROL OR CHARGE 3G iPod Questions Visit www ihomeaudio com Table of Contents Quick Station aitor e a antonia 1 Controls and Indicators iH6 Display eiecit nie dd ca 2 USiNQ the IHO ai os en 3 4 Replacing iH6 Backup BatteriesS oooooooocinnnnnnnnncconnccccconcncnnccncnnoncncnnn cnn nnnn nemen narnia 5 Install Replace Backup Battery Batteries information Using the Remote Control Unit iaa 5 A Consumer Guide to Product Safety ooooooconncccnnnniconocccnnnonccnonancnnnnnnn nan nn canon nennen nennen nere nnne nennen nnn enne 6 Troubleshooting ooo A 7 8 Solucionando problemas unicidad 9 10 Warranty InfOrMatiON soares naaa ll tan airada detener 11 A Consumer Guide to Product Safety This de
8. Mutes volume ssussss Mute Button cy Soa e a ne E Presets Sale Button Radio Button Selects Radio function AM and FM1 and FM2 radio bands Snooze mode when Snooze Dimmer Button alarm sounds otherwise dims display Install Replace the Remote Control Batteries The remote control batteries are already installed at the factory When the remote control stops operating or its range seems reduced replace the batteries with new ones 1 The battery door is located on the back end of the unit 2 Press to release the battery door latch 3 Insert one CR2032 3 volt lithium batteries Make sure the polarity the and side of the battery is correct 4 Replace the battery holder back in the remote control NOTE PLEASE DISCARD BATTERIES PROPERLY A Consumer Guide to Product Safety IMPORTANT SAFETY INSTRUCTIONS When used in the directed manner this unit has been designed and manufactured to ensure your personal safety However improper use can result in potential electrical shock or fire hazards Please read all safety and operating instructions carefully before installation and use and keep these instructions handy for future reference Take special note of all warnings listed in these instructions and on the unit 1 2 10 11 12 13 14 Water and Moisture The unit should not be used near water For example near a bathtub washbowl kitchen sink
9. defect or malfunction upon delivery of this product to the Factory Service cener ited below The product must include proof of purchase including date of purchase The fee for service without proof of purchase is 30 00 Before returning this product for service please first replace the batteries if applicable with fresh ones as exhausted or defective batteries are the most common cause of problems encountered If service is still required 1 Remove the batteries if applicable and pack the unit in a well padded heavy corrugated box 2 Enclose a photocopy of your sales receipt credit card statement or other proof of the date of purchase if within the warranty period 3 Enclose a check or money order payable to the order of SDI Technologies forthe sum of 10 00 30 00 without proof of purchase 4 Send the unit prepaid and insured to the Factory Service Center listed below Consumer Repair Department SDI Technologies Inc 1330 Goodyear Dr El Paso TX 79936 6420 Disclaimer of Warranty NOTE This warranty 1s valid only if the product is used for the purpose for which it was designed It does not cover i products which have been damaged by negligence or willful actions misuse or accident or which have been modified or repaired by unauthorized persons li cracked or broken cabinets or units damaged by excessive heat iii damage to digital media player CD s or tape cassettes i f applicable iv the cost of shipping this
10. ecesitan una fuente clase de aparto amplificado auriculares parlant de alimentaci n es que est n conectados a la ficha de salida line Aleje la unidad de Fuentes potenciales de interferencia externa como computadoras modems ruteadores inal mbricos luz fluorescente etc El funcionamiento El iH6 est reaccionando a interferencias del iH6 iPod es externas err tico No puede tocar la El iH6 puede cambiar a la 1era generaci n del Conecte la 1era generaci n del shuffle al conectador de la linea 1era generaci n del shuffle cuando el interruptor del shuffle esta en para tocar shuffle posici n para cargar pero no puede tocar 10 Limited 90 Day Warranty Information iHome Products a division of SDI Technologies Inc hereafter referred to as SDI Technologies warrants this product to be free from defects in workmanship and materials under normal use and conditions for a period of 90 days from the date of original purchase Should this product fail to function in a satisfactory manner it is best to first return it to the store where it was originally purchased Should this fail to resolve the matter and service still be reque by reason of any defect or malfunction during the warranty period SDI Technologies will repair or at its discretion replace this product without charge except for a 10 00 EE for handling packing return UPS postage and insurance This decision is subject to verification of the
11. iares Espere 1 hora y vuelva a probar El iPod no encastra E o est Verifique que el encastre sea el apropiado para su iPod correctamente El iPod no encastra correctamente Quite el iPod del encastre y retire la posible obstrucci n del encastre o de su iPod Vuelva a colocar el iPod dentro del encastre El cono de bater a Las bater as est n gastadas Reemplace las bater as pes spe Las bater as no est n instaladas Verifique que la polaridad de las bater as y se encuentren Estelango correctamente de acuerdo al diagrama del compartimiento de bater as El iPod no se El iPod no est instalado correctamente Quite el iPod del encastre y verifique posibles obstrucciones del comunica con la encastre o de su iPod Vuelva a colocar el iPod dentro del encastre unidad Su software es obsoleto Renueve su software Para mayor informaci n dir jase a http www apple com ipod download El iPod no responde Verifique que su iPod funcione correctamente antes de conectarlo a la unidad Refi rase al manual de su iPod para m s detalles Usted tiene un Pod de primera o segunda El iH6 no puede controlar estos otros aparatos generaci n un Shuffle u otro tipo de aparato No sale sonido El volumen del iH6 se encuentra muy bajo Aseg rese de subir el volumen de su iH6 El iPod no carga El iPod no est instalado correctamente Quite el iPod del encastre y retire la posible obstrucci n del encastre o de su iPod Vuelva a colocar el iPod dentro
12. ime slide the DST switch to 1 to advance the time 1 hour Slide to 1 to turn the clock back 1 hour To Set Clock Manually a Press and hold the Y Clock Adjust Button The clock display will flash b Turn the Set Wheel until the current time is displayed a PM indicator appears when time is set to PM there is no AM indicator c Press the Clock Adjust Button to accept the time The year display will flash d Turn the Set Wheel to adjust the year and press the Clock Adjust Button The date display will flash e Turn the Set Wheel to adjust the date and press the Clock Adjust Button Two beeps will indicate clock setting is complete Use DST switch to adjust for Daylight Saving Time Using the Alarms Setting the Alarms a Press and hold the 6 Alarm 1 Button until the alarm time flashes to wake to iPod buzzer alarm sounds if no iPod is detected or the Alarm 2 Button to wake to the current radio station at a separate alarm time You cannot wake to iPod shuffle b Turn the Set Wheel to set the alarm time a PM indicator appears when time is set to PM there is no AM indicator c Press the Alarm 1 Button again or the Alarm2 Button if you are setting second alarm Alarm is now armed indicated by the numbered alarm clock icon alarm 1 iPod or alarm 2 radio Arming and Disarming Alarm Turn Alarm Function ON and OFF a Press the Alarm On Off Button to arm or disarm alarm functions When armed the related alarm icon appea
13. laundry tub swimming pool or in a wet basement Ventilation The unit should be situated so that its location or position does not interfere with its proper ventilation For example it should not be situated on a bed sofa rug or similar surface that may block ventilation openings Also it should not be placed in a built in installation such as a bookcase or cabinet which may impede the flow of air through the ventilation openings Heat The unit should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat Power Sources The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance Power Cable Protection Power supply cables should be routed so that they are not likely to be walked on or pinched by items placed upon or against them It is always best to have a clear area from where the cable exits the unit to where it is plugged into an AC socket Cleaning The unit should be cleaned only as recommended See the Maintenance section of this manual for cleaning instructions Objects and Liquid Entry Care should be taken so that objects do not fall and liquids are not spilled into any openings or vents located on the product Attachments Do not use attachments not recommended by the product manufacturer Lightning and Power Surge Protection Unplug the unit from the wall socket
14. me Sound source is distorted If the iPod original sound source MP3 is old or of poor quality distortion and noise are easily noticed with high power speakers Try a different audio source such as a music CD If you are using an external sound source like older generation of iPod or iPod Shuffle try reducing the output volume on the device itself Also try turning bass boost OFF Unit adaptor gets warm This is normal Turn unit off for awhile or lower volume after extended play at high volume Can t hear Line out jack is not meant for headphones The signal from the line out jack needs amplification Use powered headphones speakers Speakers need a power source speakers monitors or other amplified audio device attached to line out jack Can t play 1st Gen The iH6 can charge 1st Gen shuffle when Connect 1st Gen shuffle to line in jack to play Shuffle shuffle switch is in Charge position but cannot play it Solucionando problemas La unidad no El adaptador de corriente AC no est conectado a Conecte el adaptador de corriente a un tomacorriente que funcione enciende un tomacorriente que funcione o no est conectado y a la parte posterior de la unidad en la parte posterior de la unidad La unidad no La unidad debe ser reprogramada Si la unidad est conectada y no responde pruebe reprogramarla responde siguiendo estos pasos a Quite el iPod de la base b Desconecte la unidad del tomacorriente Quite las bater as auxil
15. me up or down e Press the EQ Button to select Treble Bass or Balance Turn the Set Wheel to adjust settings EQ settings for iPod and radio mode are independent f Press 9 Alarm Reset Power Off Button to turn iH6 and iPod off Using the Line in and Line out J acks a An audio patch cord comes with the iH6 Use it to play nondocking iPods or other audio devices through the iH6 Line in Jack one end in the device s line out or headphones jack the other in the iH6 line in jack Make sure there is no iPod docked in the iH6 when using the line in jack however you can charge shuffle while using line in Press the iPod Button b Use the B Line Out Jack to connect the iH6 to the line in jack of other audio devices such as a tape recorder or amplifier The Volume Wheel of the iH6 does not control line out volume adjust on attached device instead The Line Out Jack is not recommended for headphones Using Sleep Mode Sleep mode lets you sleep to your iPod or the radio gradually lowering the volume until the unit shuts off at the selected time a Press the Sleep Button to select an amount of time before the iH6 will turn off 120 90 60 30 or 15 minutes b Turn the Volume Wheel to set the sleep volume this volume setting is separate from your standard volume setting Using Dimmer a Press the Snooze Dimmer Button during normal operation to adjust brightness of LCD display Replacing H6 Backup Batteries Install Replace Backup
16. quick start 2 antenna Attach AC adaptor cable to jack on back of the iH6 and plug the other end into a wall socket Snap AM antenna into provided stand then plug antenna cable into socket on back of iH6 Move antenna 12 away NOTE If you do not have an insert for your iPod please visit an Apple store www ihomeaudio com or call iHome toll free at 800 288 2792 to purchase one 4 time i SS iPod Insert iPod amp into dock with proper insert iPod must not be in askin or case iPod will charge while docked Press iPod Button on iH6 to Asp iPod nd Gen Shuffle Insert 2nd Gen shuffle into the shuffle dock included with your shuffle and plug the USB end into the iH6 s shuffle USB port To charge set Shuffle Mode Switch to ele position To lay set Shuffle Mode Switch to Play urn on al on shuffle and iPod button on iH6 Press amp hold the Time Zone button on back until it flashes Turn the Set Wheel to select yourtime zone Press the Time Zone button again Move the DST switch on back of unit to 1 or 1 adds or subtracts an hour iPod nano iPod with video 30 GB Insert 8 Insert 9 iPod 1G and 2G nano thin 30 GB iPod with video thick 60 80 GB iPod with video 3 inserts Ct Select the dock insert for your iPod model from the table below and place insert in dock Never dock an iPod without an insert in place iPod with video 60 80 GB Insert 10 Press the Radio button and
17. r Select buttons at the same time until Apple logo appears You may need to repeat this step Using 45 or 2nd generation iPod iPod Shuffle or iH6 cannot control those iPods or other devices other devices Remote Control didn t Battery weak Replace current battery with new battery NUS Remote Control is out of range of the iH6 Move within 30 feet of the unit remote sensor iH6 iPod performance is The iH6 is reacting to external interference Move unit away from potential sources of external interference such as erratic computers modems wireless devices routers or fluorescent light No sound from iH6 Volume is set too low on iH6 Make sure volume is turned up iPod didn t charge up iPod is not installed properly Remove your iPod from the dock and check for obstruction on the connectors in the dock and on your iPod Then reseat it in the dock iPod is locked up frozen Please make sure your iPod is working properly before docking into the iPod battery has problem unit Please refer to your iPod manual for details No AM band radio AM loop antenna is not connected to the unit Plug the AM loop antenna connector to the jack on the back of the unit sound but others OK AM band radio is very AM loop antenna isn t located properly Move the AM loop antenna away from the main unit iPod and rotate it noisy for best reception 7 Troubleshooting Symptom Possible Problem Solution Sound is distorted Volume level is set too high Decrease the volu
18. rking wall socket and plug the or not plugged into the power supply jack on back connector into the supply jack on the unit of the unit iH6 doesn t respond iH6 requires a reset If unit is plugged in and doesn t respond try resetting the unit by following these steps a remove iPod from dock b unplug unit from power source C remove back up batteries d wait 1 hour then resume use iPod is not docked properly Remove your iPod from the dock and check for obstruction on the connectors in the dock and on your iPod Then reseat it in the dock Battery Low icon always Batteries are weak Replace with new batteries flashing Batteries were not installed properly Check to make sure the polarity and ends matches the diagram in the battery compartment iPod does not respond iPod is not docked properly Remove your iPod from the dock and check for obstruction on the to the unit iPod is connectors in the dock and on your iPod Then reseat it in the dock a no sound Your iPod software is too old Upgrade software on your iPod For details visit http www apple com ipod download Pod is locked up plays but no sound Check the volume setting Make sure your iPod is working properly before comes out docking into the unit Please refer to your iPod manual for details See above for software upgrade information You may need to reset your iPod To do so 1 Toggle the Hold switch to hold position then off 2 Press and hold the Menu and cente
19. rs in display Resetting the Alarm to Come on the Next Day a When the alarm is sounding press the 9 Alarm Reset Power Off Button to stop alarm and reset it to come on the following day Snooze a Press the Snooze Dimmer Button after the alarm sounds The alarm will be silenced and come on again 9 minutes later Snooze can be pressed several times during the 1 hour alarm cycle Sure Alarm The iH6 has a sure alarm feature so the buzzer alarm will still sound in the event of power failure if backup batteries are installed iPod and shuffle Playing and charging your iPod a Place proper insert for your iPod see insert table under Quick Start in Dock then gently dock iPod When docked iPod will charge until fully charged Unit will not overcharge iPod b Press the iPod Button to play iPod and again to pause c Turn Volume Wheel to adjust iH6 volume up or down d Press the EQ Button to select Treble Bass or Balance Turn the Set Wheel to adjust settings EQ settings for iPod and radio mode are independent e Press 9 Alarm Reset Power Off Button to turn iH6 and iPod off Using the iH6 Playing and charging your shuffle a Dock your 2nd Gen shuffle in the shuffle Dock included with your shuffle and connect the USB plug into the USB shuffle port on the H6 To connect 1st Gen shuffle dock it directly into the USB shuffle port b To charge shuffle set Shuffle Mode Switch to Charge Unit will not overcharge shuffle c
20. vice complies with part 15 of the FCC Rules Operation is subject to the condition that this device does not cause harmful interference This equipment complies with the limits for a Class B digital device as specified in Part 15 of FCC Rules These limits provide reasonable protection against radio and TV interference in a residential area However your equipment might cause TV or radio interference even when it is operating properly To eliminate interference you can try one or more of the following corrective measures Reorient or relocate the receiving antenna Increase the distance between the equipment and the radio or TV Use outlets on different electrical circuits for the equipment and the radio or TV Consult your dealer or an experienced radio television technician if the problem still exists Modifying or tampering with your system s internal components can cause a malfunction and might invalidate the system s warranty and void your FCC authorization to operate it Maintenance Place the unit on a level surface away from sources of direct sunlight or excessive heat Protect your furniture when placing your unit on a natural wood and lacquered finish A cloth or other protective material should be placed between it and the furniture Clean your unit with a soft cloth moistened only with mild soap and water Stronger cleaning agents such as Benzine thinner or similar materials can damage the surface of the unit
Download Pdf Manuals
Related Search