PenMount 9036 Control Board
Contents
1. WAPLEX ADP 1194 Display Monitor User Manual Release Date Revision Aug 2008 V1 0 2005 Aplex Technology Inc All Rights Reserved Published in Taiwan Aplex Technology Inc 9F 5 No 2 Jian Pa Road Chung Ho City Taipei County Taiwan Tel 886 2 82262881 Fax 886 2 82262883 E mail aplex aplex com tw URL www aplex com tw ADP 1194 User Manual 1 Warning This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual it may cause interference to radio communications It has been tested and found to comply with the limits for a Class A computing device pursuant to FCC Rules which are designed to provide reasonable protection against such interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference Electric Shock Hazard Do not operate the machine with its back cover removed There are dangerous high voltages inside Disclaimer This information in this document is subject to change without notice In no event shall Aplex Technology Inc be liable for damages of any kind whether incidental or consequential arising from either the use or misuse of information in this document or in any related materials ADP 1194 User Manual 2 Ta2. 180 and 2 70 degrees rotation 0 degrees ADP 1194 User Manual 36 ADP 1194 User Manual 90 degrees 180 degrees 270 degrees 2d Stream Point Mode Stream and point modes control the touch and drag function of the touch screen The point mode only allows touch interaction with the screen and does not allow the user to drag objects The point mode is useful for maintaining the location of screen icons such on POS terminals The stream mode allows a user to touch and drag icons and other items around on the screen similar to using a mouse Drawing Mode Drawing mode is a utility that lets the user draw on the screen using a finger or stylus This allows the user to test the touch screen and touch controller to see if it is operational or is mapped correctly The drawing mode can display either the matrix address of points touched or just show lines drawn One of the PenMount driver s strengths is a special mathematical algorithm that minimizes the occurrence of noise and smooths the drawing of lines Beep Sound All of PenMount s drivers support the beep sound function however some PC systems may only offer a fixed buzzer sound Beep Sound Adjustable software drivers for Windows systems let the user adjust the frequency and length of the beep sound The drivers let the user adjust the desired touch screen sound as well as turn the sound off Wake Up Function The Wake Up function lets the user to
3. If using the PenMount 9000 control board the driver must be the PenMount 9000 Windows 2000 XP v4 01 or greater software driver 6 If using the PenMount 5000 control board the driver must be for Windows 2000 XP 2000 XP CE po 9000 Control Boards To use multiple devices with 9000 Control Boards 1 Configure your computer hardware 2 Attach each 9000 Control Board to a different computer s serial port 3 Install the appropriate PenMount software driver in each computer 4 Use each driver s Calibration function to calibrate each computer s touch screen You must calibrate each touch screen before configuration is complete Rotation There are currently a number of software packages on the market that support rotating monitors 0 90 180 and 270 However you will not be able to use a touch screen unless it is matched to the appropriate rotation Our rotation configuration function allows you to easily match the touch screen when you rotate your monitor If you use a rotating monitor you will need a display card such as from nVidia Intel SMI or ATI and software such as Portrait Pivot Pro For software operation and features please refer to your software manual Configuring the rotation function is easy Select this option and a point appears for you ADP 1194 User Manual 35 to touch Once the point is touched the software driver understands which degree you plan to rotate your display The rotation function supports 90
4. Menu and then adjust the quality with the Ad or key 1 Ifthe RGB is still on the top left corner of the screen press B to enter Miscellaneous and choose Reset and then Yes and press BII When the screen goes black disconnect power and repeat the above steps 2 If the RGB is not found disconnect the AC power cord first Then press the vy A buttons don t let them go until the AC power cord is connected and wait for 2 to 3 seconds When RGB appears repeat the above steps 3 Functions of OSD Keys ADP 1194 User Manual 10 2 3 Main Menu Color image Setting Position OSD Menu Language Misc Exit Ver 1 3 Contrast Brightness Color Adjust Color Te mp Back Ver 1 3 Clock Phase Gamma Shar press Hach ADP 1194 User Manual In the Main menu there are the following items Color Image Setting Position OSD Menu Language Misc Exit For Color check out the following Contrast Brightness Color Adjust Color Temp 6 e 9 e Back For Image setting check out the following e Clock Phase Gamma Sharpness e e e Back 11 Ver 1 3 In the Position there are the following H Position M Position Y e H Position e V Position e Back Ww Beck In the OSD menu there are OSD H Pos OSD V Pos OSD Timer Back In the Language menu there are Ver 1 3 i ED English English Frances Germany
5. Spanish Traditional Chinese simplified Chinese Japanese M wy Francais Deutsch In the Misc menu there are Ver 1 3 ol signal Source Signal Source Y ees Select VGA Analogue VGA Input mi Select DVI Digital DVI D Input select AV Composite Video Input Select SV S Video Video Input e Reset e Back ADP 1194 User Manual 12 2 4 AD Board TB 6020 OSD Functions 2 Getting into Burn in Mode Before setting into a burn in mode first disconnect the AC power cord Then press don t let them go the W buttons until the AC power cord is connected and the RGB appears on the top left corner of your screen Now it can be put into the burn in mode for changing colors 2 Getting Out of Burn in Mode Before getting out of the burn in mode please first disconnect the AC power cord Then press the x button If not workable press the A button and don t let them go until the AC power cord is connected Please don t let your fingers go until the AC power cord is connected again and the wording of RGB appears on the top left corner of your screen and wait for 3 second Under the non signal entry situation if is seen exit is thus successfully made When the Burn in Mode is Unable to Eradicate 4 Ifthe RGB is still on the top left corner of the screen press B to enter Miscellaneous and choose Reset and then Yes and press Li When the screen goes black disconnect power and repea
6. Use this function only if you have tried the Standard Calibration and there is still a discrepancy in the way the touch screen maps to the display You can choose 4 9 16 or 25 points to calibrate though we suggest that you first try 9 points if it is still not tracking well then try 16 or 25 points The more points you use for calibration the greater the accuracy Errors in calibration may occur due to viewing angle or individual skill and there may be little difference in using 16 or 25 points Note that a stylus is recommended for the most accurate results Multiple Monitors Until now most touch screen systems only support one monitor and users of multiple monitors have not been able to use touch screen systems This situation has inspired PenMount to design and develop Multiple Monitors support using the PenMount 9036 control board and Windows 2000 XP driver Our advanced design supports from 2 to 6 monitors that can be split horizontally or vertically Requirements Before using the Multiple Monitor function you need the following 1 Adisplay card that supports multiple monitors such as the Matrox nVidia ATI etc Two or more display cards supported by Windows are also OK 2 Two or more touch screens Two or more serial ports 4 Two or more PenMount 9000 control boards such as the 9036 9026 9084 or 90A4 5 The PenMount 9000 Windows 2000 XP v4 01 or greater software driver co Before using Multiple Monitors you must
7. have two or more monitors that are in extension mode For display cards that support multiple monitors we suggest you consider Matrox ADP 1194 User Manual 33 nVidia or ATI cards and inquire about operation and usability issues Note Before you can use multiple monitors you need to map each monitor Multiple Devices The Multiple Devices function is designed to let you use two or more monitors to display the same image Software that supports this function includes the PenMount 9000 2000 XP drivers and the PenMount 5000 2000 XP 2000 XP CE drivers The drivers for PenMount 9000 can support up to six control boards and the drivers for PenMount 5000 support up to 16 Comparing Functions The difference between the Multiple Monitors function and the Multiple Devices function are illustrated below A B or A B The Multiple Monitors function shown above extends the screen into 2 or more monitors ADP 1194 User Manual 34 A B The Multiple Devices function displays the same image on two or more monitors Requirements Before using the Multiple Monitors function you need the following 1 A display card that supports Dual Monitors such as the Matrox nVidia ATI etc or that outputs into a 1 into 2 VGA signal box 2 Two or more touch screens Two or more serial ports or USB ports 4 Two or more PenMount 9000 control boards such as the 9036 9026 9084 or 90A4 or PenMount 5000 control boards such as the 5184 or 51A5 5
8. sampling rate 4 5 and 8 wire touch screen supported Touch screen cable RS 232 with power cable connectors onboard 5V to 12V power input Circuit protection for input voltage Touch activated LED indicator onboard 3 3 Electrical Specifications Touch Screen 4 5 and 8 wire analog resistive type Touch Screen Controller DMC9000 Communications RS 232 Baud Rate 19200 and 9600 baud rate selection Resolution 1024x1024 10 bit A D converter inside Power Input 5V 12V DC Power Consumption 12V 24mA i where i v touch screen sheet R 5V 20mA i where i v touch screen sheet R ADP 1194 User Manual 15 Board Size 6 0 x 2 5cm Portrait Support 90 to 279 screen rotation Static Protection ESD device optional 3 4 Installation of the 9036 Controller Board Follow the steps below to install the 9036 control board 1 Power down your computer and display and open your display or system case Find space on your system and attach the control board to your system with screws The control board has industry standard 3 screw holes 2 Find the white 6 pin right angle connector on the left in the image above see Figure 3 1 The power cable is pin 1 and pin 2 Solder the power and ground wire to the system The RS 232 cable is for pins 8 to 6 Attach the RS 232 cable s D sub connector to a COM port at the back of the computer 3 Find the white 9 pin right angle connector on the right in the image
9. 32 to 113 F Storage temperature 20 to 60 C 4 to 140 F Relative humidity 10 to 95 40C non condensing Vibration 1G peak 10 150Hz Shock 10G peak acceleration 11 msec duration Certification Meet CE FCC Class A Ordering Information ADP 1194 19 SXGA industrial display monitor ADP 1194T 19 SXGA industrial display monitor with Resistive touch screen Optional 1 3 Dimensions 490 00 00000000900 00000000000 amp O 6 ammen 35 Figure 1 1 Dimensions of the ADP 1194 1 4 Brief Description of the ADP 1194 The ADP 1194 is a 19 SXGA color TFT LCD monitor that comes with a dot size of 0 264 x 0 264mm viewing angle of 160 H degrees and 160 V degrees and more outstanding features thus giving ADP 1194 User Manual 6 you the best in monitoring and control applications The front panel of the display monitor is sealed with gasket for NEMA 4 IP 65 rating when it is panel mounted in a NEMA rated cabinet or enclosure It can also be VESA 75 mounted It is optional to be equipped with a resistive touch screen Figure 1 2 Front View of the ADP 1194 ADP 1194 User Manual 7 1 5 Display Mode Display Mode Hori Sync KHz Vert Sync Hz o 81 hi iMON VGA 640 x 480 SVGA 800 x 600 XGA 1024 x 768 SXGA NEE EE EE ADP 1194 User Manual 8 Chapter 2 2 1 Front Panel OSD Functions Au
10. TS TXD RXD Ground ADP 1194 User Manual 41 Appendix B Controller IC Specifications This appendix offers information on touch screen controller IC features and specs PenMount DMC9000 Touch Screen Controller IC The PenMount DMC9000 is the best performance touch screen controller Designed with PnP features for new system trends it offers RS 232 touch screen interface The DMC9000 is designed for those who need an all in one solution with a built in A D converter for a denser total printed circuit board Ed Electrical Specifications Touch creen 4 5 amp 8 wire Package 28 pin PDIP or 32 pin TQFP Communications RS 232 Characteristics 8 bit RISC microprocessor with built in functions including 10 bit ADC UART Timer Counter Comparator Watchdog Memory etc Voltage Range 4 0V to 6 0V Power Consumption Active 3 4 mA Idle Mode 1 4mA at 4 MHz 3V Power Down Mode lt 1 uA Operating Temperature 40 C to 85 C Storage Temperature 65 C to 150 C Volt on RESET with respect 1 0V to 13 0V to Ground DC Current per I O Pin 40 0 mA DC Current Vcc and GND Pins 300 0 mA Driver Software DOS Windows 3 11 Windows 95 2000 XP Windows NT 2000 XP Linux QNX Windows CE for both X86 and SA CPUs ADP 1194 User Manual 42 Appendix Panel VESA Mounting The ADP 1194 display monitor is designed to be panel or VESA 75 mounted as shown in Figure A and Figure B Just carefully place t
11. above see Figure 3 1 Attach the female end of the touch screen cable to this connector If you attach the cable of a 4 5 8 wire touch screen to pins 1 5 1 6 1 9 attach the male end of the cable to the touch screen tail 4 Mount your touch screen to the display 5 Find the onboard DIP switch on the upper right of the image above see Figure 3 1 This switch selects baud rate PnP or non PnP mode and touch screen type Set the DIP switch to configure your control board according to the definitions and settings of the table below OFF Baud Rate Adjustment 9600 19200 6 Turn on power to the computer and the display 7 Install the software drivers and utilities and calibrate the touch screen ADP 1194 User Manual 16 Chapter 4 4 1 Windows 2000 XP Driver Installation for 9036 Control Board Before installing the Windows 2000 XP driver software you must have the Windows 2000 XP system installed and running on your computer You must also have the 9036 PenMount Serial Interface controller board installed Contents of the PenMount Windows 2000 XP driver folder are listed below DMC9000 inf DMC9000 sys DMC9000 cat SETUP EXE If you have an older version of the PenMount Windows 2000 XP driver installed in your system please remove it first Follow the steps below to install the PenMount Windows 2000 XP driver 1 When the system first detects the controller board a screen appears that shows Unknown Device Do not use t
12. are available for every driver Software functions and their availability for specific interface and systems are shown in the table below a description for each function follows Software Function DOS Win 3 1 95 2000 X NT 2000 XP CE Linux QNX p Standard Calibration e d e em e 6 em om e Advanced Calibration em e em e Multiple Monitors e Multi Device G on S Rotation em e 6 Stream Point mode on on Drawing mode e e em e on e Beep Sound e e em e on on Beep sound adjustable on on Wake up function e 5 Showing linearity on e Right button d e em e em em 9 Hide cursor 6 e e Double click area and S speed adjustable About e e en e em e HS 232 Interface 9000 series USB Interface 5000 series ADP 1194 User Manual 34 5 2 Software Function Description Description for each of the software functions shown in the table above follows Standard Calibration The Standard Calibration function lets you match the touch screen to your display so that the point you touch is accurately tracked on screen Standard calibration only requires four points for calibration and one point for confirmation Under normal circumstances Standard Calibration is all you need to perform an accurate calibration Advanced Calibration The Advanced Calibration function improves the accuracy of calibration by using more involved engineering calculations
13. ational Corp All nght reserved enldount Utilities drivers include DOG Windows 3 11 Windows 95 Windows 98 Windows ME Windows NT indows 2000 Windows XP Windows CE Linux and Onx drivers o copy modify or translate ts prohibited except with Sal s wntten consents o license PenMount Utilities drivers contact Salt Intemational Corp Emad salt salt com tw ote page www salt com tw 51 accept the terms in the license agreement O1 do not accept the terms in the license agreement Instalbhed TTE ie PenMount DMC9000 and DMC9100 InstallShield Wizard Ready to Install the Program The wizard is ready to begin installation Click Instal to begin the installation If you want to review or change any of your installation settings click Back Click Cancel to exk the wizard 19 5 The next screen is Hardware Installation Select Continue Anyway Hardware Installation A The software you are installing for this hardware PenMount DMCSOOD and DMCS100 has not passed Windows Logo testing to verly its compatibdity with Windows XP Tell me why this testing is important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing STOP Installation 6 The InstallSh
14. available for download on the PenMount website ADP 1194 User Manual 39 Appendix A Board Descriptions amp Specifications This appendix provides information on controller board features and specifications PenMount 9036 Control Board The PenMount 9036 control board is configured for the RS 232 interface and it supports 4 wire 5 wire and 8 wire touch screens PenMount 9036 Features e DMC9000 touch controller e Diagnostic LED on board e Supports PnP and non PnP mode e Supports 4 wire 5 wire and 8 wire touch screen e Baud rate 19200 or 9600 bps selectable e Automatic pin assignment adjustment e Input voltage is 5V to 12V e Bundled with PenMount drivers which are also available for download from our website Connector Pin Definitions Pin definitions for the two connectors on the PenMount 9036 control board follow Connector Pin Definitions for Touch Screen Pin definition 4 wire 5 wire 8 wire wires touch screen touch screen touch screen PIN 9 N A N A Right Sense PIN 8 N A N A Left Sense PIN 7 N A N A Bottom Sense PIN 6 N A Sense Top Sense PIN 5 Right LR Right PIN 4 Left LL Left PIN 3 Bottom UR Bottom PIN 2 Top UL Top PIN 1 Ground Ground Ground ADP 1194 User Manual 40 Connector Pin Definitions for Power and RS 232 Power Lines RS 232 Interface Pin PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 Definition Ground 5V 12V power R
15. ble of Contents WE dahl 8 c ee eae ee eee ee een eee eee 2 DPS GC LAMININ RR RE N OE OE N ON OE N 2 Chapter 1 Gettina Started D TO AW RE OO HE OO N DE OE OE EO OE EE GOED 5 I ZAG Cll Call OMS EE EE ns Ge GE 5 UNE SIGNS EA DO BR EE EE De EE ED EE Ee ES ute D T4 Briel Rein lete EE N GO de Ee 7 1 3 DI VIE MOO ee DE GE DOE UE D T 8 Chapter 2 OSD 2 1 Front Panel Control EES SS ee ee ee ee 9 22 OS E SN 6 AR EE IE EE GE RE OG ER Ee DS ED ud 9 2 3 Main Men sos aio oe rai 10 2 4 AD Board TB 6020 OSD FunctONS ee see ee ee cece ER Re EE Re ee 13 Chapter 3 Control Board 3 1 Introduction to PenMount Control Board EE SS esee 14 BP E UIES Ae 15 3 9 Electrical Specifications ER RE dara dei 15 3 4 Installation of Control Board EES SS ee ee ee eed 16 Chapter 4 Installation 4 1 Windows 2000 XP Driver InstallatioON ccc ee 17 4 2 Configuring PenMount Windows 2000 XP Driver 21 4 3 Uninstall PenMount Windows 2000 XP Driver ee 31 Chapter 5 Software 5 1 Software Functions cece cece ccc ec ccecccucccucccuccuueceueeeuesaneeans 32 5 2 Software Function Descriptions EE ee Ee ee ee Ee ee ee ee 33 ADP 1194 User Manual 3 Appendix A Board Description amp Specifications 40 Appendix B Controller IC Specifications 42 Figures LL Figure 1 1 Dimensions of ADP 1194 eese 6 F
16. e screen with your finger or a stylus and the drawing screen will register touch activity such as left right up down pen up and pen down ADP 1194 User Manual 24 Click Clear Screen to clear the drawing Multiple Monitors Multiple Monitors support from two to six touch screen displays for one system The PenMount drivers for Windows 2000 XP support Multiple Monitors This function supports from two to six touch screen displays for one system Each monitor requires its own PenMount touch screen control board either installed inside the display or in a central unit The PenMount control boards must be connected to the computer COM ports via the RS 232 interface Driver installation procedures are the same as for a single monitor Multiple Monitors support the following modes Windows Extends Monitor Function Matrox DualHead Multi Screen Function nVidia nView Function NOTE Ihe Multiple Monitor function is for use with multiple displays only Do not use this function if you have only one touch screen display Please note once you turn on this function the rotating function is disabled ADP 1194 User Manual 25 Enable the multiple display function as follows 1 Check the Enable Multiple Monitor Support box then click Map Touch Screens to assign touch controllers to displays D PenMount Control Panel Selig Calibrate Draw Multiple Monitors Option About iw Enable Multiple Monitor Support 2 When the map
17. ence with a stylus To skip press ESC PI PenMount Control Panel 80 Calibrate Draw Multiple Monitors Option About Advanced Mode 9 Plot calibration data Standard Calibration Advanced Calibration ADP 1194 User Manual 2i NOTE The older the touch screen is the more Advanced Mode calibration points you need for an accurate calibration Use a stylus during Advanced Calibration for greater accuracy PI PenMount Control Panel f BS Calibrate Draw Multiple Monitors Option About Advanced Mode 3 iw Plot calibration data Advanced Calibration ADP 1194 User Manual DI Plot Calibration Data Check this function and a touch panel linearity comparison graph appears when you have finished Advanced Calibration The blue lines show linearity before calibration and black lines show linearity after calibration D PenMount Control Panel Sele Calibrate Draw Multiple Monitors Option About Advanced Mode 3 iw Plot calibration data Standard Calibration ADP 1194 User Manual 23 Draw Tests or demonstrates the PenMount touch screen operation The display shows touch location Click Draw to start Touch the screen with your finger or a stylus and the drawing screen will register touch activity such as left right up down pen up and pen down dii PenMount Control Panel al S x Calibrate Draw Multiple Monitors Option About Touch th
18. for Windows 95 Windows 2000 XP Windows 2000 XP as well as Windows 98 USB and Windows Me 2000 XP support display rotating software packages such as e Portraits Pivot Screen Rotation Software e ATI Display Driver Rotating Function e nVidia Display Driver Rotating Function e SMI Display Driver Rotating Function e Intel 845G GE Display Driver Rotating Function Configuring the Rotation Function 1 Install the rotation software package 2 Choose the rotating function 0 90 180 2709 in the 3 party software The calibration screen appears automatically Touch this point and rotation is mapped Please touch the point N ad NOTE The rotating function is disabled if you use Monitor Mapping ADP 1194 User Manual 30 4 3 Uninstall the PenMount Windows 2000 XP Driver 1 Exit the PenMount monitor PM in the menu bar 2 Go to Settings then Control Panel and then click Add Remove program Select PenMount DMC9000 and click the Add Remove button L Bs Curent PES C coran Pl Sl penipet DERS sed pra nn MI he ar amo AE C toos Hen pare breer ye rw nr dA Bem 4 Select Yes and Close to remove the PenMount Windows 2000 XP driver and reboot the system ADP 1194 User Manual 31 Chapter 5 5 1 Software Functions This chapter describes the special software functions that configure and adjust the PenMount controller board and touch screen hardware Please note that not all of the functions
19. he unit through the hole and tighten the given 8 screws from the rear to secure the mounting Figure A Panelmounting of the ADP1194 How to Mount 1 Just insert the bracket into the hole 2 Slightly push the bracket back 3 And screw it tight as the arrow shows ADP 1194 User Manual 43 VESA 75 Mounting optional The ADP 1194 display monitor can be VESA mounted as an option Just carefully mount the arm onto the rear of the unit by fastening the given four screws as shown in Figure B aum Saa sv Duns E i e x a J Kr d z iil Figure B VESA mounting of the ADP1194 ADP 1194 User Manual 44
20. his hardware wizard Press Cancel Found New Hardware Wizard Welcome to the Found New Hardware Wizard This ward helps you install software For Urknown if your hardware came with an installation CD 22 or floppy disk insert it now What do pou want Ihe weard lo de CO Install the sollware automaticaly Recommended 5 Install trom a let ar specilic location Advanced Click Next to continue Mew i Cancel ADP 1194 User Manual 17 2 Insert the PenMount Driver CD ROM Go to the Windows 2000 XP Driver folder Click setup exe se Windows XUDO XP Driver Y4 01 fc ER ie Fevories To Hep God 0 T pass frese A Tie ond Folder Tasks tt heer Plae pa c PZW cd Me 2ccaneots c Paci Xen J Wy Eer si He L KT acs 3 The screen displays the installation wizard for the PenMount software Click Next T PenMount DMC9000 and DMC9100 InstallShield Wizard Welcome to the InstallShield Wizard for PenMount DMC9000 and DMC9100 The InstalEheld p Wizard wil install Pen ount OMC9000 and DMC9100 on your computer To continue cick Next ADP 1194 User Manual 3 A License Agreement appears Click I accept and Next 4 The Ready to Install the Program screen appears Select Install ADP 1194 User Manual T PenMount DMC 9000 and DMC9100 InstallShield Wizard License Agreement Please read the following license agreement carefully oftware License Copynght C Salt Intern
21. ield Wizard Completed appears Click Finish InstallShield Wizard Completed The InstalShield Wizard has successfully instaled Perfhiount DMC9000 and DI CS100 Click Finish to exit the ward We recommend you to reboot your computer to enable al the Functions ADP 1194 User Manual 4 2 Configuring the PenMount Windows 2000 XP Driver Upon rebooting the computer automatically finds the new 9036 controller board The touch screen is connected but not calibrated Follow the procedures below to carry out calibration 1 After installation click the PenMount Monitor icon PM in the menu bar 2 When the PenMount Control Panel appears click Calibrate PenMount Control Panel The functions of the PenMount Control Panel are Calibrate Draw Multiple Monitors Option and About which are explained in the following sections Calibrate This function offers two ways to calibrate your touch screen Standard Calibration adjusts most touch screens Advanced Calibration adjusts aging touch screens Standard Calibration Click this button and arrows appear pointing to red squares Use your finger or stylus to touch the red squares in sequence After the fifth red point calibration is complete To skip press ESC Advanced Calibration Advanced Calibration uses 4 9 16 or 25 points to effectively calibrate touch panel linearity of aged touch screens Click this button and touch the red squares in sequ
22. igure 1 2 Front View of ADP 1194 ee ee eee eee ee ee ee ee 7 Figure 3 1 Bird Eye s View of Control Board 14 Figure 3 2 Mechanical Drawing of Control Board 14 Figure A TPaAneCimMOUNUNG sien EE EE De SE DE iaia 43 Figure B VESA 75 MOUNTING sos Ge GE eee Fe end us 44 Appendix FS VION NG T 43 VESA 5 MOUNINO T 44 ADP 1194 User Manual 4 Chapter 1 1 1 Features 19 SXGA color TFT LCD monitor Heavy duty steel chassis NEMA 4 IP65 compliant Steel front panel OSD on the front panel Long backlight lifetime of 50 000 hours Panel or VESA 75mount DVI composite video and S video input optional Power Input 100 240V AC Resistive touch screen optional 1 2 Specifications Display Display 19 SXGA color TFT LCD monitor Maximum resolution 1600 x 1200 with auto phase and auto position Maximum colors 16 7M Luminance 300 cd m Viewing angle 160 degrees H 160 degrees V Backlight life 50 000 hours Control OSD on the front panel Touch screen resistive optional Power Supply Internal Universal AC DC adapter Mechanical Consiruction heavy duty steel chassis NEMA 4 IP65 certified front panel Mounting type panel or VESA 75 mount Auto recognition of input signal Dimensions WxHxD 467 x 73 x 379mm ADP 1194 User Manual Environmental Operating temperature 0 to 45 C
23. ping screen message appears click OK PenMount Control Panel PIE Calibrate Draw Multiple Monitors Option About e Enable Multiple Monitor Support Mapping Please touch the panel as indicated in the following screens ADP 1194 User Manual 26 3 4 NOTES Touch each screen as it displays Please touch this monitor Following this sequence and touching each screen is called mapping the touch screens Touching all screens completes the mapping and the desktop reappears on the monitors Select a display and execute the Calibration function A message to start calibration appears Click OK Calibrate To start calibration please touch the panel to calibrate in the following screen oe i Touch this screen to start its calibration appears on one of the screens Touch the screen Touch the red square messages appear Touch the red squares in sequence Continue calibration for each monitor by clicking Standard Calibration and touching the red squares 1 If you use a single VGA output for multiple monitors please do not use the Multiple Monitor function Just follow the regular procedure for calibration on each of your desktop monitors 2 The Rotating function is disabled if you use the Multiple Monitor function 3 If you change the resolution of display or screen address you have to redo Map Touch Screens so the system understands where the displays are ADP 1194 Use
24. r Manual 24 About This panel displays information about the PenMount controller and this driver version C PenMount Control Panel lE Calibrate Draw Multiple Monitors Option About PenMount DMC9000 and DMC9100 Driver Version 4 01 Firmware Version 41 20 COM 19200bpsi MX 4 m 1 re Tat 00806057 i t t 4 1f I L IET il IM Qd l ILS I T LL e TI 78 I L2 LL i E mail salt salt com tw Website www salf Com ty Copyright C 2003 Salt Int l Corp PenMount Monitor Menu Icon The PenMount monitor icon PM appears in the menu bar of Windows 2000 XP system when you turn on the PenMount Monitor in the PenMount Utilities PM 4 04 PM The PenMount Monitor has the following functions Control Panel Right Button Pen Stabilizer Exit m ADP 1194 User Manual 28 Beep Right Button Pen Stabilizer Exit ADP 1194 User Manual Turns beep on or off When you select this function a mouse icon appears in the right bottom of the screen Click this icon to switch between Right and Left Button functions Check this function to reduce cursor vibration for relatively unstable touch screens or where there may be excess vibration Normally this function is not checked Exits the PenMount Monitor function 29 PenMount Rotation Functions The PenMount driver for Windows 2000 XP supports several display rotating software packages The PenMount drivers
25. t the above steps 5 If the RGB is not found disconnect the AC power cord first Then press the vy A buttons don t let them go until the AC power cord is connected and wait for 2 to 3 seconds When RGB appears repeat the above steps 6 Functions of OSD Keys Auto Adjust Up Left Down Right Power Menu Entry Power Indicator ADP 1194 User Manual 13 Chapter 3 3 1 Introduction to the PenMount 9036 Controller Board The PenMount 9036 control board is configured for use with the RS 232 interface It connects to the touch screen power supply and computer system s RS 232 port and supports 4 5 and 8 wire touch screens The control board has some advanced functions such as PnP and non PnP mode adjustable baud rate thus making easy for customers to select different touch screens without changing the control board The size of the board is 25 by 60mm and it has two connectors and one dipswitch on board a no Ad crn oe a Cond 60 0 3 96 3 38 3 38 25 0 Figure 3 2 Mechanical Drawing of PenMount 9036 ADP 1194 User Manual 14 3 2 Features RS 232 interface Touch controller is DMC9000 Design for the best touch performance and easy configuration PnP or Non PnP mode selectable Design for best cost arrangement Supporting 2048x2048 pen device resolution 19200 or 9600 baud rate transmission selectable Upgraded noise handling mechanism 3 level scheme Fixed and high speed
26. to Adjust Up Left Down Right Power Menu Entry Power Indicator O Power switch To turm ON or OFF the power Y Shift the icon to the right side or shift it up amp Shift the icon to the left side or shift it down L Menu To enter OSD menu for related icon and item A gt Auto Button One touch auto adjustment 1 Getting into Burn in Mode Before setting into a burn in mode first disconnect the AC power cord Then press don t let them go the W buttons until the AC power cord is connected and the RGB appears on the top left corner of your screen Now it can be put into the burn in mode for changing colors 2 Getting Out of Burn in Mode Before getting out of the burn in mode please first disconnect the AC power cord Then press the x button If not workable press the A button and don t let them go until the AC power cord is connected Please don t let your fingers go until the AC power cord is connected again and the wording of RGB appears on the top left corner of your screen and wait for 3 seconds Under the non signal entry situation if is seen exit is thus successfully made ADP 1194 User Manual 9 2 2 OSD Controls To make any adjustment select the following 1 Press B Menu to show the OSD menu or disable the OSD menu 2 Select the icon that you wish to adjust with the Nd Or key in the menu 3 Press Hi Menu and then choose the item with the Nd or key 4 Press B
27. uch the screen and wake the system up from suspend mode Point Calibration Data The Plot Calibration Data function displays the touch screen linearity map which is available if the PenMount driver provides an Advance Calibration function when touch screens age their touch linearity declines This non linearity is apparent when the touched point on the touch screen is not the same as the point on the display The plot calibration data function shows the linearity status of the touch screen This is only a support function for the user The exact linearity of a touch screen requires a linearity test machine ADP 1194 User Manual 38 Right Button The Right Button function simulates the right button function of a mouse Click the right button and the user can only touch the screen once and the driver changes the touch definition to the left button Hide Cursor The Hide Cursor function keeps the cursor arrow and other cursor symbols from appearing when using the touch screen The cursor appears when the user turns this function off Cursor Offset The Cursor Offset function lets the user adjust the position of the touch point to a desired location away from the real touch point Double Click Area and Speed The Double Click Area and Speed function lets the user adjust the double click area and speed to their personal preference About This option shows the exact version of the drivers and controller firmware Updated drivers are
Download Pdf Manuals
Related Search