NTVKIT410 Manual
Contents
1. PIN Description Color 1 Shield 2 Shield 3 Shield 4 DIFF SIG Gray Orange S Video 3 Signal Yellow 6 Video 2 Signal White 7 Video 1 Signal Green 8 DIFF SIG Gray Blue Wire Side View Agreement End user agrees to use this product in compliance with all State and Federal laws NAV TV Corp would not be held liable for misuse ofits product If you do not agree please discontinue use immediately and return productto place of purchase This productis intended for off road use and passenger entertainment only 3 Page DS BM 3 10 14 NTV DOC094 24 PIN Navigation Connector 1 12v 4 OUT Yellow 2 ACC OUT Red 3 RXIN Blue 5 RGB B SIG Yellow 6 RGB G SIG Brown 7 RGB R SIG Red 8 RGBSYNCSIG Black 12 HIGH RES WIRE Gray 13 Ground Black 14 MUTE IN White 15 TXOUT Yellow 20 3 5mmShield Black Wire Side View 21 35mmSignal White 22 Audio Ground IN Red 23 AudioleftIN Black 24 AudioRightIN Purple 1 12v Power Yellow 2 Audio Ground OUT RADIO White 3 Audio Right OUT RADIO Gray 18 PIN Radio T Harness connector 4 Audio Left OUT RADIO Green 5 Reverse Trigger IN Red 6 Infotainment CAN HI Radio Lt Blue 7 Infotainment CAN HI Screen Purple Black 8 Vehicle CAN2. Press the Exit soft key Adjusting Contrast Touch the Contrast soft key Press the or soft key to adjust the image in 10 increments Press the Exit soft key Adjusting the Saturation Touch the Saturation soft key Press the or soft key to adjust the image in 10 increments Press the Exit soft key To exit the Camera Input Setting press the Exit soft key Agreement End user agrees to use this product in compliance with all State and Federal laws NAV TV Corp would not be held liable for misuse ofits product If you do not agree please discontinue use immediately and return productto place of purchase This productis intended for off road use and passenger entertainment only 8 Page DS BM 3 10 14 NTV DOCO94 NOTE IF NO NAVIGATION IS BEING INSTALLED SELECT NAVIGATION INPUT SETTINGS FROM THE MAIN SCREEN AND FOLLOW THE DIRECTIONS BELOW TO SELECT THE NAVIGATION SETTING TO OFF Adjusting the navigation settings if installed On the touch screen press Navigation input settings to select it Adjusting the Input Touch the Input soft key Every press of the icon will change the input OFF RGB Video 1 Video 2 Video 3 The input image will be displayed in the back ground The proper setting for ALL supported navigation devices is RGB Presently video 1 2 amp 3 are not supported If only a camera is being installed and you
3. 9 The free end of the T harness that is plugged into the radio head 18 pin connector should have been routed behind the monitor in step 4 If not do it now 10 Insert the 18 pin connector into the port labeled Radio T harness of the UCI 11 Locate the WHITE ROUND connector that was removed from the screen in step 7 Insert this cable into the WHITE port of the UCI labeled LVDS IN 12 Take the provided aftermarket LVDS cable 3 on the product description on page 1 and insert the BLACK end into the BLACK port of the UCI LVDS OUT The other end will be connected to the screen later 13 If installing a rear view camera insert the 8 pin MOLEX plug into the port labeled Video IN Of the connections available there s a Twisted Pair Used for factory installed camera only on the 4 3 screens This input is not used on the 8 4 screens On the 8 4 screens the factory camera input is on the back of the radio head b Video 1 2 amp 3 Used for an aftermarket camera input using composite video yellow RCA connection Power connections for the rear view camera must be made at the cigarette lighter 14 If installing navigation into the system proceed to the navigation installation section Otherwise continue to step 15 15 After all the connections are made securely mount the UCI module in the dash 16 Connect the WHITE end of the provided LVDS cable into the screen Make all other connections and tempor
4. Corp would not be held liable for misuse ofits product If you do not agree please discontinue use immediately and return productto place of purchase This productis intended for off road use and passenger entertainment only 7 Page DS BM 3 10 14 NTV DOCO94 D oee 4 3 Monitor Adjusting the rearview camera settings PRIOR TO ADJUSTING ANY SETTING AFTER THE INITIAL INSTALLATION TURN THE VEHICLE OFF CLOSE ALL DOORS THE HOOD AND TRUNK AND LOCK THE VEHICLE WITH THE FACTORY KEY FOB OR LOCK IT WITH THE KEY WAIT ONE MINUTE AND THEN UNLOCK THE VEHICLE AND PROCEED WITH THE FOLLOWING STEPS EVEN IF YOU ARE NOT INSTALLING A CAMERA YOU MUST PERFORM THESE STEPS a To access the settings screen press and UCI by NAV TV hold the Settings button on the upper right of the 4 3 monitor for 3 seconds Camera input settings On the touch screen press Camera Input Navigation input settings Settings to select it About Adjusting the input Exit Touch the Input soft key Every press of the icon will change the input OFF DIFF factory camera Video 1 Video 2 Video 3 Camera Settings The input image will be displayed in the back ground once the correct Video 1 input is selected Brightness IF NO CAMERA IS BEING INSTALLED Contrast SELECT OFF AND Saturation THEN EXIT Exit Adjusting brightness Touch the Brightness soft key Press the or soft key to adjust the image in 10 increments
5. Exit soft key to return to the main menu Completing the Setup Procedure VERY IMPORTANTI Agreement End user agrees to use this product in compliance with all State and Federal laws NAV TV Corp would not be held liable for misuse ofits product If you do not agree please discontinue use immediately and return productto place of purchase This productis intended for off road use and passenger entertainment only 13 Page DS BM 3 10 14 NTV DOCO94 3 After you have setup the rear view camera navigation and verified that the software in the UCI is current you will be back at the main screen This screen shows UCI by NAV TV Camera input settings navigation input setting video in motion and about Below the about is the word exit In order to store all your setting you MUST press this exit button If you switch modes during this process turn off the vehicle or disconnect any cable the settings will not be saved and you will have to start from step 1 again Put the vehicle to sleep by closing ALL doors the hood and trunk and locking the car with the key fob or key and wait 5 minutes After 5 minutes unlock the vehicle and check the system For operation please refer to page 12 reverse and navigation operation Rear View Camera The rear view surroundings will be displayed anytime the vehicle is shifted into REVERSE The image will be displayed on the factory touch screen along with the text Check Entire Surroundings The tex
6. turned the input to off make sure to select exit from the navigation settings screen and then again from the main screen to save the settings If a navigation system is being installed proceed to the section below setting the correct navigation system without exiting from the navigation settings screen Selecting the correct Navigation System This step is CRITICAL as it determines both the resolution and the communication protocol of the navigation system If you choose the wrong navigation system the resolution will be incorrect and the touch screen will not control the navigation system Touch the Model soft key to switch between 1 of 4 compatible navigation options There are 4 navigation options available NTX54 1 NTX54 2 KNA G610 and WP NTX54 1 There is a white sticker on the NTX54 designating it as an NTX54 1 Select NTX54 1 with this navigation system The NTX54 1 can ONLY be used with the 4 3 monitor The loop on the plug that plugs in at the NTX54 navigation brain MUST BE CUT when using a 4 3 monitor NTX54 2 The NTX54 2 is a resolution and communication setting only It is actually used with the NTX54 3 navigation Mone system on the 4 3 When using a Model NTX 542 NTX54 3 select NTX54 2 as the bn correct model The NTX54 3 has a white sticker on the bottom to Agreement End user agrees to use this product in compliance with all State and Federal laws NAV TV Corp would not be held liable for misus
7. Chrysler 300 cm and Red Journey is used for the Dodge Journey Contrast Model NTC Once the proper icon has been selected press Exit to exit the Navigation input setting screen leon Color Red Timing 1 ext Changing the Timing setting If after installation of the UCI with Garmin NAV the factory image is skewed in any way try adjusting Timing to Timing 2 in the Navigation settings Note If timing is off from the get go touch screen accuracy for any button may be shifted about 4 beneath the actual visual image words Once the proper timing has been selected press Exit to return to the main settings screen Changing the Video in motion settings UCI by NAVI Bi Press the Video in Motion soft key o Touch the Video in Motion soft key to change status Camera input ati On or OFF ington ia see Video in motion settings This function turns on or off the ability to watch DVD videos while the vehicle is in drive o Press the Exit soft key to return to the main menu To confirm the current hardware software revision B Press the About soft key to show current software revision The current software version is dated September 10 2012 If your software is older than September 10 2012 there is a free software update available at http navtv com page 19 downloads html labeled UCI 11C Garmin updater 9 10 2012 E A REV3 board will show hardware as 3RO and a REVS will show SRO Press the
8. Ds BM 3 10 14 NTV DOCO94 Garmin Navigation NTV KIT409 410 NTV NAVOO8 USB Cable GPS antenna R NTV KIT452 453 NTV NAV009 NTV CAB009 NTV NAV012 UCI 11c interface NTV KIT469 470 472 473 NTV ASY180 NTV NAVO15 LVDS cable NTV CAB055 Garmin Harness NTV HAR225 Ya Plug N Play T Harness NTV HAR182 NAV Traffic External speaker NTV HDWO10 Only Included with NTV KIT452 453 472 473 Cam Input Harness NTV HAR183 Only Included with NTV KIT469 470 472 473 soles ee tes hai ici Rear view camera amp Navigation solution for Dodge Chrysler amp Fiat UConnect Touch 4 3 amp 8 4 systems e Adds touch screen controlled navigation to vehicles without factory navigation e Provides a rear view camera solution for both the 4 3 and 8 4 UConnect Touch radios camera not included Allows DVD video to be viewed while the vehicle is in drive only on 8 4 DVD equipped systems Agreement End user agrees to use this product in compliance with all State and Federal laws NAV TV Corp would not be held liable for misuse ofits product If you do not agree please discontinue use immediately and return product to place of purchase This productis intended for offroad use and passenger entertainment only 2 Page DS BM 3 10 14 NTV DOCO94 UCI 11c Connector Layout Rev 5 Bluetooth or external speaker Radio T Harness C USB Update port Activity LEDs
9. HI Car Pink 9 Vehicle CAN HI Radio Blue White 10 Ground Black 1i Audio Ground IN CAR White 12 Audio Right IN CAR Gray 13 Audio Left IN CAR Green 14 12v OUT 1 amp Blue Wire Side View 15 Infotainment CAN LO Radio Brown 16 Infotainment CAN LO Car Purple 17 Vehicle CAN LO Car Pink Black 18 Vehicle CAN LO Radio Blue Agreement End user agrees to use this product in compliance with all State and Federal laws NAV TV Corp would not be held liable for misuse ofits product If you do not agree please discontinue use immediately and return productto place of purchase This productis intended for off road use and passenger entertainment only 4 Page DS BM 3 10 14 NTV DOCO94 REQUIRED Phillips head screwdriver Plastic pry tool Small pocket screwdriver Refer to online document for vehicle specific installation 1 Detailed disassembly instructions for the 300 Charger Dart and Journey are available at http navtv com page 17 manuals html under the Video Input and Backup Camera section 2 Gain access to the back of the radio head Pull out the radio enough to access the wiring behind the radio 3 Disconnect the factory white 22 pin connector from behind the radio gateway This connector supplies Power and ground as well CAN communication to the radio 4 In the kit is a 22 pin T harness Connect the removed harness from the radio to the female receptacle of the supp
10. arily reassemble the radio screen and the HVAC controls Do not reassemble permanently until the system has been thoroughly checked 17 THIS SYSTEM REQUIRES AN INITIAL SETUP PROCEEDURE PRIOR TO FUNCTIONING CORRECTLY PROCEED TO EITHER THE 4 3 SETTING SECTION ON PAGE 8 OR THE 8 4 SETTINGS SECTION ON PAGE 11 DEPENDING ON WHICH SIZE MONITOR IS IN YOUR VEHICLE 18 After making the necessary changes in the SETUP menu test the system and reassemble If Installing Navigation Once you complete step 13 of the UCI installation continue from this point 1 Plug in the supplied 24 pin Navigation harness into the port on the UCI labeled NAVIGATION AV Agreement End user agrees to use this product in compliance with all State and Federal laws NAV TV Corp would not be held liable for misuse ofits product If you do not agree please discontinue use immediately and return product to place of purchase This productis intended for off road use and passenger entertainment only 6 Page DS BM 3 10 14 NTV DOCO94 2 Route this cable down to the location where you will be installing the NTX54 navigation unit Be sure to securely fasten it to existing wiring and brackets and route it away from any sharp or moving parts 3 After all the connections have been made to the UCI module it is time to mount it We recommend using the large space available behind the monitor in the dash cavity and securing it with Velcro For added stability a large zip tie sh
11. compliance with all State and Federal laws NAV TV Corp would not be held liable for misuse ofits product If you do not agree please discontinue use immediately and return productto place of purchase This productis intended for off road use and passenger entertainment only 14 Page DS BM 3 10 14 NTV DOCO94 P1 I installed the piece and now the radio does not come on and the HVAC does not work A1 Check to make sure that the T harness is plugged in securely and that the mini molex is plugged into the UC1 2 If plugged in unplug the T harness and do a visual inspection for bent pins or pins that have popped out Align the pins or put them back into the correct position and reconnect the harness securely A3 Check for the REV3 1 sticker to verify the hardware is current for a REV3 If a REVS does this remove one side and slide the board out Check to see if the daughter card has become dislodged Simply reseat the daughter card and retest A4 Have the unit plugged into a computer to check to make sure that the software is current and correct for the application AKA rev3 software in a REVS or outdated software Update the unit and retry P2 installed the piece and the radio comes on but there is a black screen I cannot even get the factory screen to come on A1 YOU DIDN T READ THE DIRECTIONS AND INSTALLED THE VIDEO IN AND OUT AT THE RADIO INSTEAD OF AT THE SCREEN Put the factory LVDS cable back to factory and verify that the fa
12. ctory image comes on If it does put the radio back into the dash loosely and access s the back of the monitor At this point NO LVDS CABLES SHOULD BE PLUGGED INTO THE UCI IN ORDER unplug the white LVDS cable at the back of the monitor and plug it into the white port on the UCI Then plug the BLACK end of the included LVDS cable with a white and a black end into the UCI Now plug the white end of the included cable into the monitor Check for factory pass through If good proceed to programming A2 If A1 didn t solve the problem and it is a REVS board have them remove one end and reseat the daughter card and retest A3 If nothing fixes the issue check for the proper software and update if needed P3 I installed the piece and the factory rear view camera no longer works A1 You did not set up the rear view camera settings after installation Go into the settings menu and select rear view camera Change the setting to head unit Select exit and exit again to store the setting Perform a CAN reset and retest P4 I cannot get into the settings menu at all A1 Do a CAN reset and try again A2 Check to make sure you have the proper software 4 3 or 8 4 rev3 or rev P5 I installed an aftermarket rear view camera and it doesn t work A1 See P3 above and instead switch the input to a different setting and retest A2 try a CAN reset after A1 is performed again Agreement End user agrees to use this product in compliance with all State and Fe
13. deral laws NAV TV Corp would not be held liable for misuse ofits product If you do not agree please discontinue use immediately and return producto place of purchase This productis intended for off road use and passenger entertainment only 15 Page DS BM 3 10 14 NTV DOCO94 P6 installed an aftermarket or factory fit camera and the screen only goes to a black screen in reverse or the picture is wavy and distorted A1 See p5 above and repeat A2 You didn t power the rear view camera Check power A3 You selected the wrong input A4 You powered the camera off of the reverse lights Run camera power to the front cigarette lighter AS You attached the factory fit camera wires backwards Correct and retest P6 The factory fit camera works but it has a wavy line at the bottom of the screen A1 You grounded the drain wire Cut it loose and retest A2 Do a CAN reset and retest BUT this time with the car RUNNING to check for a low voltage condition P7 I installed the system and I get no image or a distorted image when trying to switch to navigation A1 Make sure the proper navigation system has been selected A2 If installing either a Kenwood or a NTX54 make sure that pin 8 on the Garmin plug is showing ground for an 8 4 or no connection and no ground for a 4 3 A3 Make sure the proper software is in the unit P8 The touch screen controls are not working on the unit BUT I can see a navigation screen A1 You selected
14. e ofits product If you do not agree please discontinue use immediately and return product o place of purchase This productis intended for off road use and passenger entertainment only 9 Page DS BM 3 10 14 NTV DOCO94 identify it as an NTX54 3 The loop on the plug that plugs in at the NTX54 navigation brain MUST BE CUT when using a 4 3 monitor KNA G610 Select this setting when using a Kenwood KNA G610 navigation system WP Select this setting when using a Directus Intraphex or Wonde Proud Navigation system To exit the Navigation input setting press the Exit soft key To confirm the current hardware software revision Press the About soft key to show the current software revision The current software uc ux version is dated September 10 etre 2012 If your software is older Le than September 10 2012 there is on a free software update available at http navtv com page 19 downloads html labeled UCI 11C_Garmin updater 9 10 2012 A REV3 board will show hardware as 3RO and a REVS will show 5RO Press the Exit soft key to return to the main menu Completing the Setup Procedure VERY IMPORTANTI After you have setup the rear view camera navigation and verified that the software in the UCI is current you will be GA back at the main screen This O screen shows UCI by NAV TV Nndgaton Input setings Camera input settings navigation input settings and about Below the about is the word exit In o
15. elect it Adjusting the input o Touch the Input soft key o Every press of the icon will change the input OFF Head Unit factory camera Video 1 Video 2 Video 3 The input image WILL NOT be displayed in the back ground during the camera selection o NOTE The differential input at the UCI IS NOT USED WITH THE 8 4 monitor o IF NO CAMERA IS BEING INSTALLED SELECT OFF AND THEN EXIT o IF THE VEHICLE HAS A FACTORY CAMERA YOU MUST SELECT HEAD UNIT OR THE CAMERA WILL NOT FUNCTION AFTER INSTALLATION AND YOU WILL BE REQUIRED TO FOLLOW THESE STEPS AGAIN o If installing the Charger Cam also select Head Unit The Charger Cam installs at the back of the radio not the UCI Please follow the included Charger cam instructions O To exit the Camera Input Setting press the Exit soft key ANOTE THE UCI IS NOT INTENDED AS JUST A REAR VIEW CAMERA INTEGRATION MODULE FOR THE 8 4 SYSTEM IF YOU ARE ONLY INSTALLING A REAR VIEW CAMERA YOU SHOULD USE THE UCT84 NTV KIT 297 and the UCT differential camera adapter NTV KIT314 instead Agreement End user agrees to use this product in compliance with all State and Federal laws NAV TV Corp would not be held liable for misuse ofits product If you do not agree please discontinue use immediately and return product o place of purchase This productis intended for off road use and passenger entertainment only 11 Page DS BM 3 10 14 NTV DOC094 Adjusting the navigation settings if i
16. ent only 16 Page
17. lied harness Take care not to bend any of the pins in the female receptacle when inserting 5 Plug the male plug of the T harness into the radio where the factory connector was located If any other cables were disconnected when the radio was removed plug them back into the radio Slide the radio gently back into the opening and route the extension harness with the 18 pin connector up behind the monitor Do not secure the radio with the factory screws until the installation has been completed and tested Agreement End user agrees to use this product in compliance with all State and Federal laws NAV TV Corp would not be held liable for misuse of ts product If you do not agree please discontinue use immediately and return productto place of purchase This productis intended for off road use and passenger entertainment only 5 Page DS BM 3 10 14 NTV DOC094 6 Using the plastic pry tool gently pry around the dash panel surrounding the monitor to release the locking tabs Take extra care when releasing these tabs they may fall from the dash panel and into the dash 7 Gain access to the rear of the screen amp disconnect the 3 cables that are attached PAY ATTENTION TO THE WHITE CIRCULAR 4 PIN PLUG THIS PLUG WILL BE INSERTED INTO THE UCI IN LATER STEPS IF YOU INSERTED ANYTHING AT THE RADIO INTO THE UCI AT THIS STAGE PUT THE VEHICLE BACK TO STOCK AND START AGAIN AT INSTRUCTION 1 8 Set the monitor and or dash assembly aside
18. nstalled o Press the Navigation input settings soft key Navigation Settings Navigation On Brightness Adjusting the input o Touch the Navigation soft key o Every press of the icon will change the input OFF amp ON Only the RGB input is available The input image will not be displayed in the back ground Make sure that the input setting is selected to ON Yon Color ad Tming 1 Contrast Model NTX 54 2 eat To exit the Navigation Input Settings press the Exit soft key Bi DO NOT SELECT EXIT AT THIS POINT FROM THE NAVIGATION INPUT SETTINGS SCREEN YOU MUST SELECT THE PROPER NAVIGATION SYSTEM AS WELL AS THE COLOR ICON AND SCREEN RESOLUTION IN THE FOLLOWING SECTION Selecting the proper Navigation system o This step is CRITICAL as it determines the communication protocol of the navigation system If you choose the wrong navigation system the touch screen will not control the navigation system o Touch the Model soft key to switch between 1 of 4 compatible navigation options There are 4 navigation options available NTX54 1 NTX54 2 KNA G610 and WP 0 NTX54 1 This setting is NOT USED on the 8 4 and is only for future use The NTX54 1 navigation system is not compatible with the 8 4 monitor If you are attempting to install a navigation system in a vehicle with an 8 4 screen and the NTX54 has a white label that says NTX54 1 STOP and contact the establishment you purchased the unit fr
19. om and have the navigation exchanged 0 NTX54 2 The NTX54 2 is a communication setting only It is used with either the NTX54 2 NTX54 3 NTX54 4 navigation system on the 8 4 When using a NTX54 2 3 4 select NTX54 2 as the correct model The NTX54 2 amp NTX54 3 have a white sticker on the bottom for identification NOTE The NTX54 2 is used ONLY in 8 4 vehicle that have factory Bluetooth The NTX54 3 can be used either with an external speaker OR in vehicles with factory Bluetooth The loop on the plug that plugs in at the NTX54 2 or NTX54 3 navigation brain MUST BE INTACT and NOT CUT when using an 8 4 monitor Agreement End user agrees to use this product in compliance with all State and Federal laws NAV TV Corp would not be held liable for misuse ofits product If you do not agree please discontinue use immediately and return productto place of purchase This productis intended for off road use and passenger entertainment only 12 Page DS BM 3 10 14 NTV DOCO94 o KNA G610 Select this setting when using a Kenwood KNA G610 navigation system The loop on the plug that plugs in at the KNA G610 navigation brain MUST BE INTACT and NOT CUT when using an 8 4 monitor 3 Once the proper Model Navigation has been selected you need to stay on the same screen and select the Icon Color o Touch the Icon Color soft key m o Every press of the icon will change the icon Red is used TT T4 for the Dodge charger Blue is used for the
20. ould be used to secure the module in place 4 Plug the routed cable from the UCI into the NTX54 navigation unit at the power connector 5 If installing a REVS product and the vehicle has FACTORY BLUETOOTH skip to step 8 If you are installing a REV3 product OR if the vehicle does not have FACTORY BLUETOOTH continue with step 6 6 Included in the kit is an external speaker it is used for turn by turn navigation or any audio output from the navigation unit The speaker can be mounted on one of the metal rails running vertically under the steering column It is recommended that the speaker faces the opening under the steering column for best volume 7 Plug the speaker into the 3 5mm jack on the UCI to navigation harness 8 The GPS antenna needs to be installed right side up in a location that has a clear line of sight of the sky The antenna can be mounted on the dash or located in the dash below the dash pad without any metal obstructions Be sure the antenna is securely mounted with Velcro 2 sided stick tape or a metal surface 9 Connect the antenna to the jack labeled GPS ANT on the navigation unit 10 Return to step 15 in the UCI installation instructions and then proceed to the SETTINGS section for your screen size GPS Antenna connector Power connector NAV Traffic Antenna port Only for NTV KIT469 470 472 473 Agreement End user agrees to use this product in compliance with all State and Federal laws NAV TV
21. rder to store all your setting you MUST press this exit button If you switch modes during this process turn off the vehicle or disconnect any cable the settings will not be saved and you will have to start over from step 1 again Put the vehicle to sleep by closing ALL doors the hood and trunk and locking the car with the key fob or key and wait 1 minute Agreement End user agrees to use this product in compliance with all State and Federal laws NAV TV Corp would not be held liable for misuse ofits product If you do not agree please discontinue use immediately and return product to place of purchase This productis intended for off road use and passenger entertainment only 10 Page DS BM 3 10 14 NTV DOCO94 After 1 minute unlock the vehicle and check the system For operation please refer to page 12 reverse and navigation operation 8 4 Monitor Adjusting the rearview camera settings PRIOR TO ADJUSTING ANY SETTING AFTER THE INITIAL INSTALLATION TURN THE VEHICLE OFF CLOSE ALL DOORS THE HOOD AND TRUNK AND LOCK THE VEHICLE WITH THE FACTORY KEY FOB OR LOCK IT WITH THE KEY WAIT ONE MINUTE AND THEN UNLOCK THE VEHICLE AND PROCEED WITH THE FOLLOWING STEPS EVEN IF YOU ARE NOT INSTALLING A CAMERA YOU MUST PERFORM THESE STEPS To access the settings screen press and hold the Power button on the HVAC controller for 5 seconds A menu will appear on the monitor after 5 seconds On the touch screen press Camera Input Settings to s
22. t will remain on the screen for 10 seconds and then will fade out Once the vehicle is shifted out of REVERSE the image will fade into the previous mode or screen Do not rely completely on the rear camera image periodically check your surroundings for obstacles Navigation 4 3 monitor To display navigation press the Screen Off button This will display the navigation home page To exit navigation press the Screen Off button again Audio prompts will be heard through the external speaker Refer to the navigation documentation for operation 8 4 monitor When navigation is enabled a new icon will show up in the bottom right corner of the screen where the More soft key is located This icon may take up to 10 seconds to appear once the vehicle has been unlocked To access the navigation press the Nav soft button on the lower right corner The navigation screen will be displayed All the functions of the navigation can be controlled through the factory touch screen Refer to the user manual for operation To exit the navigation screen press the desired source The More soft touch button for the factory SETTINGS screen can be accessed through the navigation screen While in navigation mode if the climate control is adjusted the navigation screen will disappear anytime the system is being accessed 3 seconds after the last operation the navigation screen will return Agreement End user agrees to use this product in
23. the wrong navigation type Change the navigation model to the correct type and retry Make sure to select exit and exit again P9 Selections are not being stored correctly A1 You are not selecting exit and exit again A2 On some vehicles it requires a CAN reset before some settings will stick correctly Perform a CAN reset and try again close all doors lock car and return retest in 10 minutes P10 I installed the Garmin or Kenwood system into a 4 3 and i get a distorted navigation picture A1 Cut the wire in pin 8 on the Garmin harness and retest You must put the UCI to sleep first as it will not allow a hot swap resolution change Do a CAN reset and retest P11 I installed the system into a vehicle without Bluetooth and I thought it had it A1 Both the NTX54 1 and NTX54 3 are compatible with an external speaker Only the NTX54 2 does not have the capability to power an external speaker Check the version of the NTX54 to determine whether or not it is compatible P12 My factory image and NAV image is distorted in general A1 Try adjusting the Timing setting in the NAV settings Refer to 8 4 Screen settings Agreement End user agrees to use this product in compliance with all State and Federal laws NAV TV Corp would not be held liable for misuse ofits product If you do not agree please discontinue use immediately and return product to place of purchase This productis intended for off road use and passenger entertainm
Download Pdf Manuals
Related Search