AQ200 Manual
Contents
1. AQ 200 y Il Introduction Connections eo Interchangeable measurement modules Interchangeable modules with Smart plus system are automatically recognized when connected to the instrument 1 Current voltage module 2 Thermocouple module It allows current or voltage measurements on V A1 or VA 2 It allows thermocouple temperature measurement on Tc1 channels with current voltage input cables or ammeter clamps Tc2 Tc3 and Tc4 channels with type K J or T with wire thermocouple probes equiped with a miniature male connector 3 Climatic conditions module It allows hygrometry measurement on Hygro channel ambient temperature measurement on Ptx channel and air pressure on PATM channel SD Wire probes with Smart plus system Pt100 Temperature Wire probes with Smart plus system are automatically recognized when connected to the instrument Probes are connected on min DIN connectors C1 and or C2 Mini Din C2 Mini Din C1 connector connector Secured Mini Din Connector 02 Wireless probe instrument communication Wireless communication between probe and instrument with automatic recognition after power up e Pt100 probes are displayed on Tr1 or Tr2 channels followed by wireless communication Le Wireless probes shall be located near the instrument for initial recognition Connection between AQ200 and wireless probes must be established See submenu2. Hold Min Max pg e ETER Rec gt Alarms Press 1x in order to select HOLD function measurement holding on display Press 2x in order to select Min Max function display of minimum and maximum values Press 3x back to the continuous measurement IV Menus Configuration A If you use thermocouple probes you must enter type into the Configuration sub function Configuration sub function allows to e Select thermocouple Click on OK or to enter into sub function a list of thermocouple available K J or T type appears Select type with A and W Confirm with OK Select display Click on OK or to enter into sub function Select channel required with arrow keys A and V and confirm with OK Select respectively ON or OFF with A and V inorder to enable or disable this function Confirm with OK e Select units Click on OK or to enter into sub function a list of units available appears For each channel select unit required with A and V Confirm with OK Click on Esc to return to previous screen Delta T When two PT100 probes or 2 thermocouple temperature probes are connected AQ200 can calculate Delta temperature value the temperature difference between C2 and C1 or T2 and T1 or T4 and T3 Select Delta T in order to view the temperature difference If you select Delta T again Delta T function is disabled Alarms Select respectively ON or OFF with
3. S E INSTRUMENTS AQ CIC Air Quality sa Table of contents KENE ere le Tu acciai 4 Technical featUres vnrrrreeeeeeeeeeeee eee eee eee eee eee 4 Specifications 4 Il Titele eeler ge Tu BEEN 5 BIEL EE D Ba a go 218 a e aaa aaa EEN 6 UE ge ae Meer tere bara 7 Aa nd es 8 Probe mena ea ale iena err O rete ee een ieee eee eee eras 8 Using wire probes and Mr de UN 8 USE wireless POSS ik is A a i i a i a 8 UG UA Sessa asis ai aaa ais aa a a a a a aaa can a ia aa de D is tt 8 Recordings isties sanat i a p sa a a i B o i a a i a a 9 Bel li ias aa a a k i i E a i E a tine 11 Be Te aa 11 Date time aid ka aa a a aa T ai a i a atei 11 RF logMaar a a aaa 11 G0 aL ors e AS AEE E EA E a a A a 11 Wownloaghngdata ale 11 V General information rece 12 Tei te EL S i slice 12 Val e ZE ne 12 M AO EE ie as a i aaa Aaa i i a a a a a i S a a A 12 Technical specifications o Technical features Sensing elements M UE Graphic display 128x128 pixels Dim 50 x 54 mm blue blacklit Display of 6 Air quality probe measurements including 4 simultaneously CO NDIR infrared sensor Non dispersive infrared Housing IP54 ABS shock proof CO Electrochemical sensor Keypad Metal coated 5 keys 1 joystick Temperature Pt100 class A Conformit Elect tical ott Hygrometry capacitive
4. Wireless probes p 8 III Browsing dy TT ____ Power up 7 Enter code 0000 Homepage display ios ee Frate Faremo Y Probe connection Probes display oe Measurement Measurement display Return to previous screen SECH Probe Config Cerone Enter key code with directional pad if the locking is activated D ad AV Select a sub menu with access keys or with arrow keys 1 P Select a connection with right and left keys lt gt Connections can be activated or deactivated with A or V Select a sub menu with access keys or with arrow keys lt gt Select a sub menu with access keys or with arrow keys 1 P Communication interrupted Check probes connection IV Menus Probe menu 1 Using wire probes and modules Wire probes and modules with Smart plus system are automatically recognized from first connection The Probe menu only appears when probes or module are connected This menu allows to view probe information plugged to C2 Module C1 or wireless connections See Connections p 6 for more information about connections Probe display Available information are e Sensor type Serial number Date of last calibration or adjustement Probes Status enabled ou disabled On enabled mode the probe is connected the measurement is carried out and the value is displayed Infos g
5. of reading 0 3 C 0 1 C Air pressure hPa from 800 to 1 100 hPa 3 hPa 1 hPa CO Temperature i p C F from 20 to 80 C 0 4 of reading 0 3 C 04 C CO ppm from 0 to 100 ppm 5 ppm 1 ppm from 101 to 1 000 ppm 3 of reading 5ppm CO Temperature Temp Go F from 20 to 80 C 0 4 of reading 0 3 C 041 C Ss H CO ppm from 0 to 5 000 ppm 3 of reading 50 ppm 1 ppm CO Temperature Hygrometry Temp Cr F from 20 to 80 C 0 4 of reading 0 3 C 0 1 C CO from 0 to 5 000 ppm 3 of reading 50 ppm 1 ppm Hygro from 5 to 95 RH See Climatic conditions module 0 1 RH D from 50 to 250 C According to model Pt100 Smart plus or wireless probes See related datasheet 0 3 of reading 0 25 C According to model 0 01 C All accuracies indicated in this document were stated in laboratory conditions and can be guaranteed for measurements carried out in the same conditions or carried out with required compensation As per NFX 15 113 and the Charter 2000 2001 HYGROMETERS GAL Guaranteed Accuracy Limit which has been calculated with a coverage factor value of 2 is 2 88 RH between 18 and 28 C on the measuring range from 5 to 95 RH Sensor drift is less than 1 RH year The accuracy is expressed either by a deviation in C or by a percentage of the value concerned Only the bigger value is considered II Introduction CN
6. A and V in order to enable or disable the alarm Choose your setpoint CO Limit 1 first CO setpoint CO Limit 2 second CO setpoint low temperature setpoint and high temperature setpoint Confirm with OK or gt Select thresholds with OK or Kk to enter CO and temperature setpoints Select or signs with A and V then pass on the first digit with B Low and high thresholds entered confirm with OK Recording Select dataset The Recording menu allows a measurement dataset You can choose between a planned or a continuous dataset Memory capacity of the instrument is up to 8 000 points or 50 datasets 1 Create or launch a continuous dataset A continuous dataset can be carried out using AQ200 and is composed of several dated measuring points The Enter name operator can choose an automatic or a manual dataset with an instant value or an average This datasets can t be set using Datalogger 10 Software 1 1 Manual dataset A manual dataset is composed of measuring points selected by the operator a Click on OK or gt to enter into sub function Manual dataset b Select Manual with A and V Confirm wih OK c Select Name with A and V Confirm wih OK or Enter dataset name with arrow keys lt q gt and V Confirm wih OK d For measurement launching click on OK with the access key The number of points selected and the parameter are displayed e To save your dataset click on Save with the access
7. e Summary screen of selected dataset is displayed From this screen you can e Select other dataset using arrow keys lt and gt e Display data of other channels using arrow keys A and V d Click on Mesure to display values table of selected dataset Dataset table From this screen you can cast IT Browse values table of points of the same channel pressing Prev or Next e Change of channel with arrow keys lt and P e Back to dataset summary screen pressing Visu 4 Delete all datasets Select Delete with A and V Confirm wih OK IV Menus oO Parameters e Language Click on OK or to enter and a list of languages available appears Select language with arrow keys A and V and Confirm wih OK e Date time Click on OK or gt to enter into sub function Enter the day with A and VY then move to the next digit with gt Repeat this operation for the month year hour and minute Confirm wih OK e Beep This sub function allows to enable or disable the keypad beep Click on OK or gt to enter into the sub function Select respectively ON or OFF with A and V inorder to enable or disable the beep Confirm wih OK e Extinction This sub function allows to enable the automatic shut off and to select the delay in minute Click on OK or to enter into the sub function Select with A and V OFF in order to disable the automatic shut off or enter the delay from 15 to 120 minutes Confi
8. e mail info eintrumentsgroup com
9. hygrometry sensor onformity ectromagnetical compatibility NF EN 61326 1 norm Climatic conditions module Power supply 4 alkaline batteries 1 5V LR6 Hygrometry capacitive hygrometry sensor Temperature semiconductor temperature sensor Air pressure capacitive sensor Operating environment Neutral gas Operating temperature from 0 to 50 C Storage temperature from 20 to 80 C Thermocouple probes type K J and T class 1 Auto shut off adjustable from 0 to 120 min Pt100 Smart plus probes Pt100 class 1 3 Din Weight 380g AQ200 connection see p 6 Languages English French Measuring units Measuring ranges Accuracy Resolutions CURRENT VOLTAGE V mA from 0 to 2 5 V 2mV 0 001 V from 0 to 10 V 10mV 0 01 V from 0 to 4 20 mA 0 01mA 0 01 mA THERMOCOUPLE See related datasheet C F K from 200 to 1300 C 1 1 C ou 0 4 Reading value 0 1 C Qi qe J from 100 to 750 C 0 8 C ou 0 4 Reading value 0 1 C T from 200 to 400 C 0 5 C ou 0 4 Reading value 0 1 C CLIMATIC CONDITIONS Hygro RH from 5 to 95 RH Accuracy Repeatability linearity 0 1 RH hysteresis 1 8 RH from 15 C to 25 C BE Factory calibration uncertainty 0 88 RH Temperature dependence 0 04 x T 20 RH if T lt 15 C or T gt 25 C Temp C F from 20 to 80 C 0 4
10. key IV Menus 1 2 Automatic dataset Auto dataset An automatic dataset is composed of measuring points with interval of time a Click on OK or to enter sub function b Select Auto with A and V Confirm wih OK c Select Name with A and V Confirm wih OK or Enter dataset name with the arrow keys gt and A V Confirm wih OK d Enter dataset time and interval of time between 2 measurements by selecting Period with access key Select Duration or Interval with A and V Confirm wih OK Enter minutes and seconds with arrow keys amp and V from 1 minute to 24 hours for the duration and from 5 seconds to 10 minutes for the interval Confirm with OK e Select Start for dataset launching 2 Launch a planned dataset A planned dataset is composed of several locations For each location the operator can enter a theorical value and a tolerance for the parameter to be controlled Planification must be made via the software a Click on OK or gt to enter into sub function b Select Planned with A and V Confirm wih OK c Choose dataset name with A and V Confirm wih OK d Select the location with A and W Confirm wih OK 3 Preview of tables of points of datasets Dataset summary You can display tables of points of datasets performed on the device a Go to Recording menu b Select Display Click on OK to validate c Select dataset name with arrow keys A et W Click on OK to validat
11. rm wih OK e RF logging This sub function allows to enable or disable the RF logging Click on OK or to enter into the sub function Select respectively ON or OFF with A and V inorder to enable or disable this function Confirm wih OK Downloading data see DataLogger 10 user manual chapter III Read device page 6 V General information Info menu This menu allows to view the serial number of instrument and firmware version Battery When battery indicator flashes it is recommended to change the batteries 1 Remove the front part at the back of the instrument 2 Remove batteries 3 Insert new batteries AA LR6 1 5V in accordance with proprer polarity drew inside the housing 4 Replace the front Maintenance KIMO performs calibration adjustment and maintenance of all your instruments to guarantee a constant level of quality of your measurements In regards of Quality insurance norms we recommend that the instruments are checked once a year Warranty KIMO Instruments have 1 year guarantee for any manufacturing defect return to our After Sales Service required for appraisal NTang AQ 200 02 09 C We reserve the right to modify the characteristics of our product Ld E Instruments Group LLC Distributed by 172 Middletown Blvd Suite B201 E instruments Langhorne PA 19047 GROUP LLC Tel 215 750 1212 Fax 215 750 1399
12. t Measure Params On disabled mode the probe is connected the measurement is not carried out and the value is not displayed RF probes display 2 Using wireless communication A Add a wireless probe A1 Go to probe menu by pressing Probe access key A2 With arrow keys and P go to RF probes display A3 Select with access key RE pibes searching A4 Power up the probe and press multifunction button until LED blinks Once the probe is recognized information appears Left button lt allows to return to the wireless probes display and to access all wireless probes already recognized by the instrument With access keys it is possible to delete Del a wireless probe RF probes detected E E E B Select a wireless probe already created B1 Power up the wireless probe short press on Multifunction button B2 Go to Probe menu B3 With arrows keys and gt go to RF probes display All the wireless probes already recognized appear L i B4 Select the suitable wireless probe with A or V bio B5 Go to probe informations using arrow key bt B6 Enable the wireless probe with arrows keys A and V and confirm with OK Functions The following functions are enabled only if at least one probe is connected You can access to the following sub functions Hold Min Max Configuration Delta T Parameters Calculation Recording Measurement display
Download Pdf Manuals
Related Search