Printer Cleaning Guide
Contents
1. imagine SlRoland Printer Cleaning Guide geatae ye E CLEANING KIT E TWEEZERS To clean the print heads you need a Roland Cleaning Kit and a pair of tweezers Contact your Roland dealer if you do not have the cleaning kit CLEANING LIQUID CLEANING SWABS Use this specially formulated Unlike cotton tipped swabs cleaning liquid for SOLJET these special swabs contain i no waste fiber To remove excess dirt Included with your printer inkjets Do not use any other cleaning liquid Only Roland SOLJET Cleaning Liquid is approved for use Do not use general cotton tipped swabs The cotton fibers can leave residue on the print heads LEANING AREAS There are four main areas to clean on your printer Point 1 The side of the print heads Point 2 Around the cap Point 3 Point 4 Around the wipers Replace the wipers LEANING PROCEDURE l 1 Enter the MAINTENANCE 3 Remove the maintenance 2 Select the mode cover s mode SOL JET PROIIV VersaCAMM SP Series SOTJET EROI OSE UNIS Ee Remove the screws Point 1 The side of the print heads Point 2 Around the cap Left cover Hold down the CLEANING key and Right cover turn on the sub power CLEANING a G Point 3 Around the wipers SOL JET PROIII amp VP Series O Turn on the sub power Point 4 Replace the wipers Apply cleaning l2. premature print head failure Point 4 Replace the wipers Replace the wipers if they are worn and deformed First use the tweezers to unlock them at the base of the wiper holders Then pull them off using the tweezers Install new wipers making sure that they are fully locked into place at the base O Check wipers on a regular basis to ensure their performance After the cleaning perform a TEST PRINT to confirm the print quality If problems persist try multiple Medium Cleanings If the TEST PRINT does not improve perform a Powerful Cleaning Instructions on both cleaning are found in the user s manual In addition to the areas mentioned above dirt can also build up in the following locations Use the cleaning swab to remove dirt from these areas and to prevent any loss of print quality eT Around the Pinch Rollers Poor media tracking is a sign of dirty pinch roller wheels Stains and scratches to the media may indicate this problem as well For pinch rollers apply mild soap and water to the cleaning swab Do not use cleaning liquid or alcohol RolandCare Support Documents Some dirt may also settle in the following places Around the Media Clamps This problem will impair media tracking and reduce print quality For the VersaCAMM remove the media clamps and clean them by applying Isopropyl alcohol to the cleaning swab For SOLJETs apply mild soap and water to the swab Around the Flushing Spo
3. iquid to the cleaning swab Use a new cleaning swab every time you perform a cleaning Do not reuse the cleaning swab This can result in loss of print quality RolandCare Support Documents mm Page 1 T 0845 230 9060 E techsupport rolanddg co uk W www rolanddg co uk support Point1 The side of the print heads In the CLEANING mode the heads reposition themselves next to the left cover First take the cover off Using the cleaning swab thoroughly remove any dirt dust and or ink from all four sides front back right and left of the print heads While wefking A B anhes sweb be earefitt esttg touch the print head surfates d KEEN 7 KEREGA Zaa y When dirt accumulates along the sides of the print head print quality is impaired This can also cause a premature print head failure Point 3 Around the wipers Take off the right cover and remove the dirt around the wipers using the cleaning swab and tweezers Dirt around the wipers may interfere with the cleaning process and can also scratch the print heads imagine SllRoland Point2 Around the cap With the cleaning swab and tweezers remove the dirt and ink around the cap Only the tweezers should be used to remove the dirt and debris from the inner sponge area Work gently and try not to damage the rubber gasket surrounding the cap The accumulation of dirt around the cap gasket impairs the print head s seal to the cap Over time this problem can cause
4. nge Frame This problem can damage the print head surface and reduce print quality For this cleaning apply SOLJET cleaning fluid to the swab Note that a saturated or swollen sponge needs replacement mm Page 2 T 0845 230 9060 E techsupport rolanddg co uk W www rolanddg co uk support
Download Pdf Manuals
Related Search