Maxi Changer
Contents
1. gt H1 Coin Hopper 1 Coin or Token type H2 Coin Hopper 2 Coin or Token type H3 Coin Hopper 3 Coin or Token type BE CAREFUL be sure that BONUS are not present in the option COIN Use NEXT and ENTER buttons to configure the hoppers Push TEST to come out V N E Srl 55047 Querceta LU Via Biagioni 371 Tel 39 0584 742530 www vne it Empty Hopper Hopper Value Hopper type gt Bonus Hopper lt ENTER gt H1 C No Bonus H2 C No Bonus H3 C No Bonus Version 1 1 1 18 01 2013 PAGE 11 13 C represents Coins T Tokens C represents Coins T Tokens C represents Coins T Tokens Through NEXT and ENTER buttons it is possible to configure the bonus as the following schedule TABLE 5 PIECES 10 PIECES 20 PIECES 40 PIECES 0 NO BONUS NO BONUS NO BONUS NO BONUS 1 BONUS 1 BONUS 3 BONUS 7 BONUS 15 2 BONUS 0 BONUS 1 BONUS 3 BONUS 7 3 BONUS 1 BONUS 3 BONUS 7 BONUS 7 4 BONUS 0 BONUS 1 BONUS 3 BONUS 3 N B If it is set to 0 there are not BONUS if the hopper is set as coin dispensing it won t be possible to set the BONUS the display will show the entry NO BONUS If the hopper is set as money dispenser not tokens the BONUS can not be set for obvious economical reasons the BONUS must be removed if you want to activate the payment function One Token at a Time To come out push TEST Hop2. 0 H2 0 H3 0 Er Note Acceptor 0 Er Coin Acceptor 0 Version 1 1 1 18 01 2013 PAGE 13 13 hopper 1 hopper 2 and hopper 3 status code hopper 1 hopper2 and hopper 3 error code note acceptor error code coin acceptor error code Status codes OK ok NP not present FU full MT empty If error code is 0 no errors are present on the peripheral Otherwise an error is present 17 Security For security reasons we made more complex entering in the menu to see the data and configure the machine In order to enter the menu you need to keep pressed the button TEST for more than 3 seconds 18 2p MaxiChanger differences The only real difference between 2p Machine and MaxiChanger Machine is that MaxiChanger Machine has a Banknote Acceptor V N E Srl 55047 Querceta LU Via Biagioni 371 Tel 39 0584 742530 www vne it
3. V N E Srl 55047 Querceta LU Via Biagioni 371 Tel 39 0584 742530 www vne it Version 1 1 1 18 01 2013 PAGE 3 13 1 Preliminary remarks V N E S r l does not accept any responsability when e Operative procedures of transport maintenance and peripheral installation included in this manual are not respected e The system has been used in operative conditions which are not included in those limits established for the respect of environmental conditions e The damage occurs after repairs or changes made by non authorized staff e The damage is the result of a system natural deterioration 2 Introduction It is forbidden to reproduce convey or copy any parts of this manual for public and or private use without V N E S r l permission All the information included in this manual concern data referring to V N E S r l V N E S r l reserves the right to modify this document without notice The machine is created and planned in conformity with 2004 108 CE 2006 95 CE Community guidelines we followed CEI EN 55014 1 2007 CEI EN 55014 2 1998 A1 IS1 CEI EN 61000 3 2 2007 CEI EN 61000 3 3 1997 A1 A2 IS1 CEI EN 60335 2 82 2005 rules for the CE requirement control Transitory decreases of performances could occur in the case of particular interferences from the outside such as electrostatic discharges or transistors on the supply lines The machine will regularly work as soon as the trouble stops The machine should be used indoor a
4. Version 1 1 1 18 01 2013 PAGE 1 13 Ye Quality Management System Certification 50 100 8093 Rev 02 V N E Srl Via Biagioni 371 55047 Querceta LU Tel 39 0584 742530 Fax 39 0584 768333 www vne it TECHNICAL AND OPERATING MANUAL 2p MaxiChanger V N E Srl 55047 Querceta LU Via Biagioni 371 Tel 39 0584 742530 www vne it Version 1 1 1 18 01 2013 PAGE 2 13 INDEX Preliminary remarks Introduction Manual purpose and structure Manual use Maker and machine identification 5 1 Maker 5 2 Machine 5 3 Component list 5 4 Year of fabrication 6 Technical data 6 1 System technical features Ar oe deo 6 2 Technical features of the Omnibox control board 6 3 Technical features of the internal supply 6 4 Hopper technical features 6 5 Technical features of F30 F40 bill validator 6 6 Display technical features 7 Environmental conditions 7 1 Temperature 7 2 Humidity 7 3 Altitude 8 Security standards 9 Installation 9 1 General standards of installation 10 Use procedures 11 Maintenance 12 Out of order placing instructions 13 Transport and handling 14 Conformity declaration 15 Enclosures 16 Configuration and data visualization 17 Security 18 2p MaxiChanger differences Attention This sign means that before doing any operation it is necessary to read and follow all the security information included in this manual When in doubt please contact our skilled staff
5. ance service e Make sure the fuses on the electric supply system are exclusively replaced by fuses of the same type in order to avoid risks of fire It is forbidden to use different fuses or materials e The machine should be appropriately connected to the ground in order to avoid electric shocks due to malfunctioning e If the supply cable is damaged replace it immediately with another similar cable Do it after having disconnected the main supply e Do not put any objects on the supply cable and control that the cable is not in a passageway The cable should not be wrapped or tied e Do not use the machine near water or other kind of liquids If some liquid goes into the machine diconnect immediately the cable from the socket Do not touch metal parts of the machine and ask technical staff to control the machine before using it again e Do not lay any container with liquids on the machine even if it the device is out e Disconnect the supply cable from the socket during storms e Do not service inside the machine but contact the skilled staff e Disconnect the supply before clearing the machine externally Do it by using a dry cloth Do not leave the keys in the machine and keep them in an area not easily accessible to the user V N E Srl 55047 Querceta LU Via Biagioni 371 Tel 39 0584 742530 www vne it Version 1 1 1 18 01 2013 PAGE 5 13 9 Installation 9 1 General standards of installation e Place the machine in areas being ou
6. ard V NE S r l ccTalk interface boards Lcd 20x4 display 54 Year of fabrication 2011 6 Technical data 6 1 System technical features Supplytension isunr aaa 230 V Fredu Oye aa er rina 47 63 Hz Max energy consumption 110 W Protection FUSE crepe tito n es eed 1 6A Weight rante 80 Kg Dimensions carie aaa arci 350x1350x320 mm 6 2 Technical features of the Omnibox control board PCB dimension iprniiarana ia aa 99x78 mm Power supply tension 5 Vdc Working frequency as 4 Mhz V N E Srl 55047 Querceta LU Via Biagioni 371 Tel 39 0584 742530 www vne it Version 1 1 1 18 01 2013 PAGE 4 13 6 3 Technical features of the internal supply Supply tension i c aiunissssla rien etiam cin 176 264 VAC BTCQUCTI Cyst cet arty eaceP an ert E 47 63 Hz Output tensions nie Eee 5Vdc 12A 12Vdc 8A 24Vdc 4A 6 4 Hopper features Supply tensioni i psisoi dichia lia lizadziazi 24Vcc Max consumption eseeeeteeeeeeeseeecseeeseeeseeeaeeeens 1A Working temperature se 5 C a 55 C Dimensions oe 130x290x230mm Welght nia delliride 1 8Kg 6 5 F30 F40 Taiko bill validator Supply tension 24Vcc Max consumption ie 1A Working temperature ie 0 C a 50 C Dimensions w 138x81x128 mm Weight ciare lia ibid Iliade 1 1Kg 6 6 Display Supply tension i SVec Ma
7. e by pushing the button related to the hopper instead of the whole credit Push NEXT to come back to the previous screen Push NEXT again to enter the menu hopper Pay One Token gt Hopper lt Auto Payment ENTER gt Empty Hopper lt Hopper Value Hopper Type Bonus Hopper ENTER Hopperl 0 Hopper2 0 Hopper3 0 By pushing the button of the hopper for more than 5 seconds you will start the emptying procedure 100 pieces at a time Left button for hopper 1 center button for hopper 2 and right button for hopper 3 Push TEST to come out NEXT to pass to the subsequent option of the menu V N E Srl 55047 Querceta LU Via Biagioni 371 Tel 39 0584 742530 www vne it Version 1 1 1 18 01 2013 PAGE 10 13 Empty Hopper gt Hopper Value lt Hopper Type Bonus Hopper ENTER gt H1 00 00 GBP H2 00 00 GBP H3 00 00 GBP In this page the coin token value of each hopper is visualized To set change the values push ENTER Hopper 1 value gt 0 lt 0 00 EUR Use NEXT and ENTER to set the values push TEST to come out from the menu H1 00 00 GBP gt H2 00 00 GBP H3 00 00 GBP Push ENTER to configure even the hopper 2 with exactly the same procedure of the previous paragraph Then as always push TEST to come back to the previous menu Empty Hopper Hopper Value gt Hopper Type lt Bonus Hopper ENTER
8. hake the machine it contains fragile parts e Use the bill validator in the right way by inserting only the acceptable banknotes e For smokers do not place any cigarette on those parts of the machine which are not suitable 11 Maintenance Ordinary and extraordinary maintenance and takings withdrawal should be done by qualified staff who has to observe the following prescriptions e Do not modify the machine without previous maker authorization e In case of repair or substitution of components use only spare parts which have been approved by V N E e Before starting any maintenance intervention make sure that the machine is out and the supply cable is disconnected from the system e Disconnect the supply system and the main connectors of the machine by seizing connectors and not individual cables e Before connecting or disconnecting any connector or plug make sure that the machine switch is OFF Make sure that the front of the machine is separated 50 cm at least from any other obstacle in order to guarantee the substitution of internal parts of the machine supply board etc REPAIR Machine repairs should be done only by technical and skilled staff or in our repair centre Some power supply parts are still hot or keep dangerous tensions for a period of time Even if the machine is switched off there are risks of burns or electric shocks Do not touch accidentally these parts 12 Out of order instructions e Do not dispose of the prod
9. nd for those purposes established in the planning V N E S r l does not undertake any responsability for accidents or damage caused by a wrong or non authorized use of the machine 3 Manual purpose and structure e The aim of this manual is to avoid states of risk for the installation use and maintenance staff and to avoid environmental conditions and behaviours which could damage the coin changer machine or its component parts e This manual is part of the machine and should always be at operative and working staff disposal e This machine should be used only and exclusively indoor and for the purposes established in the planning e If you do not respect prescriptions of this manual you will lose the warranty 4 Manual use All the information about installation and maintenance address to technical staff trained in electricity and plant engineering It is necessary to read carefully this manual and keep it in an easily accessible place in order to consult it and use the machine in a correct and secure Way This manual is made up of 13 pages 5 Maker and machine identification 5 1 Maker V N E S r l Via Biagioni 371 55046 Querceta LU Italia P I 01840210460 5 2 Machine 2p MaxiChanger Change machine 5 3 Component list Azkoyen Hopper mod T3 or similar hopper Genna Group power supply mod PS 8250X MW 610 Mean Well Bill validator EDUE Italia mod F30 F40 ccTalk Cash code V NE S r l Omnibox control bo
10. observe the main requirements demanded by 2004 108 CEE and 2006 95 CEE Directives Verona P I Nicolino THE MAKER RESERVES THE RIGHT TO MODIFY THE MACHINE DESCRIBED IN THIS MANUAL AT ANY TIME AND WITHOUT NOTICE AS FOR TECHNICAL SPECIFICATIONS V N E Srl 55047 Querceta LU Via Biagioni 371 Tel 39 0584 742530 www vne it Version 1 1 1 18 01 2013 PAGE 7 13 15 Enclosures DISPLAY TOS POWER SUPPLY OMNIBOX CcTalk Interface HOPPER HOPPER HOPPER ADO COIN 1 2 3 VALIDATOR MaxiChanger V N E Srl 55047 Querceta LU Via Biagioni 371 Tel 39 0584 742530 www vne it Version 1 1 1 18 01 2013 PAGE 8 13 V N E S r l 2p MAXICHANGER USER MANUAL The 2p MaxiChanger machine has been created to be a device simple to use and at the same time reliable and secure You can configure the machine through a configuration menu You enter into the menu by pushing the test button inside the machine You can set the value of each hopper with coin token from 0 to 10 with step lcent You can independently set the two hoppers with coins or tokens It is possible to set different Bonus schedules for those hoppers which have been set with token In the case one hopper is set with token and the other with coin the machine can dispense the rest in tokens 16 Configuration and Data Visualizati
11. on To enter into the programming menu and visualization data push the TEST button check chapter 17 which is inside the machine the three external dispensing buttons hopper 1 left hopper 2 center hopper 3 right correspond to PREV ENTER and NEXT gt Accounting lt Peripherals Button Test Info ENTER right button B in 0 00 GBP C in 0 00 GBP lt Prev Next gt NEXT left button l out 0 00 GBP 2 out 0 00 GBP 3 out 0 00 GBP lt Prev Next gt NEXT left button 1B out 0 pcs 2B out 0 pcs 3B out 0 pcs lt Prev Next gt banknotes in coins in hopper 1 coin out hopper 2 coin out hopper 3 coin out hopper 1 bonus pieces out hopper 2 bonus pieces out hopper 3 bonus pieces out In this page there is the partial accounting of the last zeroing To zero the accounting push ENTER button for more than 5 seconds Push TEST to come out from the menu Push NEXT to enter into the peripheral menu V N E Srl 55047 Querceta LU Via Biagioni 371 Tel 39 0584 742530 www vne it Version 1 1 1 18 01 2013 PAGE 9 13 Accounting gt Peripherals lt Button Test Info ENTER gt Pay One Token Hopper Auto Payment ENTER Pay One Token At a time Off On activated Off deactivated Push ENTER to activate the function One Token at a Time This function allows you to dispense coins only one by on
12. per Pay One Token gt Auto Payment lt ENTER Automatic Payment Off On activated Off deactivated Push ENTER to activate the function Automatic payment This function allows you to automatically dispense the credit when you insert the notes Push NEXT to come back to the previous screen Then TEST to go the previous menu V N E Srl 55047 Querceta LU Via Biagioni 371 Tel 39 0584 742530 www vne it Version 1 1 1 18 01 2013 PAGE 12 13 Accounting Peripherals gt Button Test lt Info ENTER H1 1 H2 1 H3 1 Test 1 DipSwitch 000000 By pushing the related buttons it is possibie to verify the proper working To come out push simultaneosly PREV and NEXT Accounting Peripherals Button Test gt Info lt ENTER gt Last Notes lt Machine Status 1 1 1 software version ENTER to visualize the list of the last notes TEST to come back to the previous menu 1 0 GBP 5 0 GBP 2 0 GBP 6 0 GBP 3 0 GBP 7 0 GBP 4 0 GBP 8 0 GBP List of the last eight entered notes where is the most recent and the 8 the lessrecent Push TEST to come back to the previous screen NEXT Last Notes gt Machine Status lt 1 1 1 software version ENTER to visualize the machine status V N E Srl 55047 Querceta LU Via Biagioni 371 Tel 39 0584 742530 www vne it St H1 OK H2 0K H3 0K Er H1
13. t of atmospheric agents in a vertical and firm position out of the rays of the sun in not extremely humid or dusty places and far from air conditioners or radiators Fix the machine to the wall by using the screws included in the equipment The fixing holes are in the back of the machine e Check whether the wall where 2p MaxiChanger will be fixed is suitable If the screws are assembled in a wrong way or the surface is not suitable there could occur damage to people or things whose V N E S r l is not responsible for e Do not place the machine next to the emergency exits or instruments used to put out the fire e Make sure that the ventilation system respects the right distances from surrounding walls and furniture e Take precautions against any possible seepage in the machine e Supply the machine with the power supply reproduced on the tag Check the electric system compliance with current prescriptions concerning plant engineering L 46 90 e OUT OF ORDER PLACING REGULATION REPAIR and DIAGNOSTICS procedures should be done by authorized technical staff 10 Use procedures e Insert one or more banknotes in the bill validator and or one or more coins in the coin validator e Wait for the visualization of the amount on the display e Select the denomination coin token to obtain by pushing the right button e Wait for the exit of all the amount of coins tokens e Withdraw coins tokens and eventually the change e Do not s
14. uct among waste material It is necessary to dispose the product following rules for particular waste products 13 Transport and handling e Transport and handling procedures should be done by trained staff able to use specific means If you do not respect this recommendation there would be physical damage to people or to the machine e The machine has parts which are susceptible to vibrations and or crashes It is necessary to pay attention to transport and moving e The machine should be transported in closed means and it should be properly fixed e It is forbidden to lift the machine with cables or belts because it does not have specific points of fixing e If you want to move the machine in different places make sure power supply cable is disconnected and well preserved V N E Srl 55047 Querceta LU Via Biagioni 371 Tel 39 0584 742530 www vne it Version 1 1 1 18 01 2013 PAGE 6 13 14 Conformity declaration Firm V N E S r l Via Biagioni 371 55046 Querceta LU Italy Machine 2p MaxiChanger Change machine Managing director Nicolino Verona REGULATIONS 1 EN 55014 1 Emissions EN 61000 3 2 Emissions Harmonic EN 61000 3 3 Emissions tension fluctuations Flicker EN 55014 2 Immunity EN 60335 1 Security of electric devices for domestic use and similar 1 These rules include the variations related to the date of this document The maker states that the product suits the above mentioned regulations and
15. x consumption ie 50mA Working temperature 0 C a 50 C Dimensions pilalilale dani avida libianganiaa 121x41 mm 7 Environmental conditions 7 1 Temperature Operating 10 to 40 C Storage 5 to 55 C 7 2 Humidity Operating 10 to 95 Storage 5 to 95 7 3 Altitude Operating until 4 000 m Transport until 10 000 m 8 Security standards Before installing the machine or working on it it is necessary to read carefully this manual When the machine is installed or serviced by a different staff the owner should ensure that this staff has read the instructions of this manual It is necessary to follow these prescriptions in order to avoid any danger of accident e Start the machine only after having controlled the adequacy of installation and the conformity with the information included in this manual e Do not install the machine in areas subject to sudden changes in temperature and humidity e Check the visibility and good condition of labels referring to security e Place the machine at a minimum distance of 15 cm from any obstacle and not upon blankets or other soft surfaces Moreover avoid to install the machine near radiators or enclosed areas which do not have a suitable ventilation e Do not switch on the machine if it is not completely installed in the correct way e Supply the machine with the electric power supply indicated on the proper tag When in doubt please contact the technical assist
Download Pdf Manuals
Related Search