Contents List of Figures List of tables User manual MONIKA 2, ROTA
Contents
1. INQ Fig 1 Construction of the device 1 Shelf for handling goods on the glass 2 Bent front glass lifted 3 Glass display shelf 4 Display shelves 5 Front screen 6 Front fender beam 7 Front customer shelf 8 Illuminated front panel 9 Basis of the device 10 Aluminium lamp with illumination 11 Night screens made of plexiglas 12 Granite working top made of stainless steel or furniture board in Rota 13 Maximum loading line sticker on the glass side 14 Evaporator 15 Rail condensate outflow after defrosting the evaporator 16 Storing chamber 17 Cooling aggregate 18 Data plate 19 ABS sides 20 Wooden platform fixed for transport of the device 21 Device levelling feet 22 Storage chamber doors 23 Wind brace when removed access to con denser lamellas 24 Control panel temperature regulator switches 2 3 Technical data Table 1 Technical data Ud Rated voltage Rated current Rated lighting PEAR Shelf load Weight of the MONIKA ROTA V Hz A power W KWh 24h kg mb device kg 1 0 230 50 1 1 18 3 6 50 110 1 3 230 50 i 30 3 8 50 130 1 5 230 50 1 5 36 4 9 50 150 1 7 230 50 2 0 58 6 4 50 170 2 05 230 50 2 0 58 6 4 50 190 2 5 230 50 2 4 60 7 6 50 220 In devices with illuminated front panel the rated lighting power i2. Carel thermostat temperature regulators is described in chapter 7 p 19 and 20 The basic aim of a thermostat is to control the cooling aggregate to obtain the set temperature within the device and maintain it within the determined temperature ranges The producer enters all settings of temperature regulators required for normal functioning of the device Before primary actuation the user should control and possibly set the required tem perature inside the device on the control panel Digital display displays the current temperature inside the device It is forbidden to interfere with systemic parameters of the thermostat as this can lead to serious consequ e ences including the damage of the cooling device 5 MAINTENANCE 5 1 Cleaning and maintenance All maintenance services need to be performed after disconnecting the device from power supply Protect electric installation against any damage or water spillage oe Do not use water stream to clean the device only a wet cloth os Do not use any sharp objects to remove filth f Devices equipped with wheels cannot be used on uneven surfaces During cleaning the inside of the device do not leave the front glass freely lifted in the aluminium profile This may cause the damage of the glass and is not covered by warranty Please remove the glass with profile for the time of cleaning Fig 8 p 16 Fig 8 Front glass Fig 9 Temp
3. Lower night screen shorter one mounted as the first one 2 Upper night screen longer one mounted as the second one 3 Leaf of the aluminium lamp hides and secures the night screens before falling out 4 Night screen guide aluminium profile o Sie Wy A LLLLLLILLED Fig 6 Condensate container 1 Rail water outlet hose condensate outflow after condenser evaporation 2 Condensate container empty the condensate Fig 7 Control panel 1 Main switch turns on off the aggregate of the device 2 Lighting switch 3 Thermostat temperature regulator panel service details in Chapter No 7 p 19 and 20 Cm o zL 4 EXPLOITATION Temperature of the cooled space and aggregate operating cycle may fluctuate They depend on numerous factors such as amount and temperature of products placed in the device and temperature of the surroundings The device should be placed in a dry and well ventilated place ensuring proper air exchange distance between the wall and the device min 10 cm out of sunlight kept far from heat sources and devices enforcing air flow ceiling and portable ventilators blow in heaters The device functions properly in a room where temperature falls within appropriate climatic class stated on the data plate The operation of the device may worsen when it shall operat
4. IGLOO User manual MONIKA 2 ROTA 1 UNLOADING The device should be transported in vertical position and it should be properly secured and packed The manufacturer ships the device on a special wooden platform secured with cardboard angle sections and foil 2 PROPERTIES OF THE DEVICE 2 1 Purpose Monika 2 Rota is a universal cooling device used to store and display a wide assortment of grocery products in singular packages previously cooled to storage temperature Our display cabinets ensure universal and efficient display area for all types of commercial and gastronomic units Guaranteed temperature inside the display cabinet equals 2 C 8 C with ambient temperature of 15 C 25 C and relative air humidity of up to 60 2 2 Description of the device Monika 2 Rota display cabinet has static cooling All types are equipped with automatic defrosting and electronic ther mostat optionally cooperating with temperature recording module enabling to record and signal too low and too high temperature within the device There is also an option with automatic condensate evaporation Monika 2 Rota display cabinet is furnished with a storage chamber Our devices are made according to modern technologies and have all cer tificates required by law Contents List of Figures 1 UNLOADING 11 Fig 1 Construction of the devige 12 2 PROPERTIES OF THE DEVIGE x ccmancatemtaanimanennuee 11 Fig 2 Removing the wooden platfo
5. O without noticing the user Copying the present manual without the consent of the producer is forbidden Images and drawings are of demonstrative character and may differ from the purchased device 20 User manual Monika 2 Rota www igloo pl
6. brush or Mit paint brush If the condenser is extremely dirty blocked lamellas it is indicated to use vacuum cleaner or com pressed nitrogen to suck blow the dirt from between lamellas Fig 11 Changing the fluorescent lamp 4 Starting switch of fluorescent lamp o 3 Casing of fluorescent lamp and Fig 10 Cleaning the condenser The producer shall not be held responsible for damages of the condenser aggregate resulting from non observance of condenser cleanliness 1 Fluorescent lamp handle 2 Fluorescent lamp starting switch Door seal should be cleaned solely with clean water without any cleansing agents and it sho uld be thoroughly dried The seal cannot get into contact with oily substances or grease Control whether door close properly during maintenance procedures Test place a sheet of paper between the seal and the casing and close the door The paper should pose a tangible resistance during an attempt to pull it out Elements of device can corrode when improper used and maintenance To avoid that please follow the rules e Do not allow contact of the surface of the device with substances containing chlorine and or baking soda in different varieties which destroy the protective layer and components of the device also includes various stainless steel During maintenance services it is necessary to pay attention not to damage the data place o
7. dden to connect the device by means of extension cords or dividers Power sockets optional may be used to power cash register weight and similar receivers with power not e exceeding 500W e Turn on the main switch Fig 7 1 p 15 which activates the temperature regulator and then aggregate of the device e Set the temperature on thermostat control panel Fig 7 3 p 15 service details on p 19 or 20 e Turn on the lighting switch Fig 7 2 p 15 Fig 2 Removing the wooden platform 1 Unscrew the feet from the platform 2 Remove the wooden platform 3 Screw the feet in nuts welded to the frame of the device User manual Monika 2 Rota 13 amp IGLOO en Fig 3 Assembly of display shelves 1 Display shelf 2 Front aluminium angle section 3 Back aluminium angle section Fig 4 Assembly of glass elements and aluminium lamp 1 Pressure of the glass glass side 7 Lower aluminium profile glass catch 2 Glass side 8 Front screen made of glass 3 Aluminium lamp 9 Front bracket 4 Aluminium lamp hole plug 10 Lamp conduit protection 5 Bent front glass lifted 11 Lamp conduit 6 Upper aluminium profile lifted guide of the glass 14 User manual Monika 2 Rota www igloo pl iy e amp 3 Fig 5 Assembly disassembly of night screens 1
8. e eae p 6 1 Fault identification and repair the purchased MOC GRZALEK 0 00 W device still does not work properly please e Description of the problem eee contact Technical Service of the Igloo e Your exact address and telephone ILO CZYNNIKA 0 company stating the data from the data number with the code number ZAKRES TEMPERATUI KLASA URZADZENIA plate Fig 12 p 18 DATA PRODUKCJI 09 2008 GAZ SPIEN IZOLACJ HFC 365 227 Typ NAZWA URZ DZENIA The above figure shows a demon The data plate is located at the back strative data plate and the data stated of the device in the upper right cor spa ie Pate exp aby cola ner below the top Fig 1 18 p 12 MADE IN POLAND Gi which are not related with Monika 2 D Rota device 5 907759 500353 CE Fig 12 Data plate 18 User manual Monika 2 Rota www igloo pl ra g Ey Gz we rr rm r q E i AN E Ge i Ge 7 THERMOSTAT SERVICE 7 1 IGLOO thermostat Fig 13 lgloo thermostat control panel 1 Cooling on off switch 2 Manual defrosting switch 3 Aggregate and defrosting operating control diode 4 Temperature monitoring switch on defrosting sensor 5 Temperature regulation switch increase 6 Temperature regulation switch decrease Verification of adjusted temperature inside the device By pressing A or W switch once we can verify the adjusted t
9. e in temperature lower or higher than the stated temperature range Remarks and indications e It is necessary to properly level the display cabinet which will prevent loud operation of the device and shall ensure proper water condensate outflow during defrosting e After transporting the device wait about 2 hours before its actuation e The first filling of cooling space should be performed after its previous cooling to working temperature This principle should also be observed after longer pause in exploitation e Do not block any ventilation holes which would hamper circulation of the cooled air It is also necessary to ensure proper airflow around the device aggregate ventilation holes cannot be covered e Ensure even load on shelves do not exceed their maximal load and do not exceed maximal loading e Keep the condenser clean Impurities may lead to overheating of the compressor and as a consequence may result in damage of the device which is not covered by warranty e Do not use electric devices inside grocery product storing chamber e After closing the door of the device it is not recommended to open it with force Negative pressure created inside the device is levelled within 1 2 minutes which allows easy opening of the door e Avoid unnecessary opening of doors and leaving them open for a longer period of time www igloo pl User manual Monika 2 Rota 15 Vv 4 1 Temperature regulation Service of Igloo and
10. emperature The adjusted temperature shall be shown on the display with a visible red blinking spot diode The preview shall finish automatically after about 3 seconds Lowering or increasing the temperature press Y or A switch and the adjusted temperature shall be visible on control panel By pressing the Y switch we decrease the temperature to the desired value The preview shall finish automatically after about 3 seconds Manual defrosting switch No 2 enables to initiate the defrosting cycle at any moment when the device is working re gardless of the automatic defrosting function the switch shall not operate when the temperature is higher than the final defrosting temperature The user should switch on switch off the aggregate only by means of the main switch of the device and e not by means of the direct switch on thermostat control panel Switching on the main switch shall automa tically initiate the thermostat Read more on www igloo pl User manual Monika 2 Rota 19 63 IGLOO en 7 2 CAREL thermostat Fig 14 Carel thermostat control panel WHAT DO DIODES ON CONTROL PANEL SIGNIFY Diode 1 is on Compressor the symbol is visible when the compressor is working It is blinking when compressor actuation is delayed by security procedure It blinks in the following cycle two blinks pause when the co
11. erature sensor disassembly inside the device 1 Front glass 1 Temperature sensor 2 Upper aluminium profile mo 2 Evaporator screen lifted guide of the glass oo 3 Evaporator drip rail 3 Lower aluminium profile PA catch of the glass When using the display cabinet as well as during maintenance works pay attention not to destroy the tempe rature sensor in the evaporator screen It is recommended to make a break in the exploitation of the device once a month in order to clean its interior naturally defrost the evaporator clean the condenser and verify the condition of door seals If the device is not equipped with automatic condensate evaporation it is essential to remove the condensate from the container when filling the container Fig 6 p 15 The number frequency of condensate removal depends on device exploitation conditions f ex air humidity door opening frequency the amount and temperature of products placed for storage Do not use mechanical agents in order to fasten the defrosting process 16 User manual Monika 2 Rota It is essential to keep the condenser of the device cle an Dirt may hinder the heat exchange causing mainly increase in electric energy consumption and may cause damage of aggregate compressor In order to clean the condenser it is necessary to unscrew the sheet metal screws and pull the wind brace out Clean condenser lamellas with help of soft
12. f the device Fig 12 p 18 which contains significant information for servicing organs and waste removal companies 6 SERVICE 6 1 Fault identification and repair In case of any difficulties during actuation of the device or during its exploitation please return to these chapters in this ma nual which explain the performed operation This aims to ensure that the device is properly operated If you still experience difficulties the following hints will help you solve the problem The device is not working Make sure that The device is connected to the supply network Voltage and frequency in the network are compliant with those recommended by the producer 230V 50Hz The main switch is turned on Thermostat is turned on This concerns the Igloo thermostat If only two spots are visible on the display turn on the thermostat The device is operating but the lighting is off Make sure that Lighting switch is turned on Fluorescent lamp or starting switch of the device are not burnt Water leakage from below the device or into the inside of the chamber Check whether the device is properly levelled Check the patency of outflow pipes Empty the condenser tray or container Check whether there is not too much ice in the rail and on the condenser defrost when necessary User manual Monika 2 Rota 17 ea gt Taa The device does not reach the proper temperature
13. ng in progress this is not an alarm signal This concerns the IGLOO thermostat The device is working sound signalling is activated Make sure that The condenser is clean if necessary clean the condenser e Condenser ventilator is working properly e Ambient temperature does not exceed 25 C The device is working too loud Make sure that e The device is standing stably e Furniture adjoining the device do not vibrate when the cooling aggregate compressor is working Noises made by the operating device are a normal phenomenon The devices are equipped with venti lators engines and compressors which turn on and off automatically Each compressor makes certain noises when operating These sounds are made by the aggregate engine and by cooling agent flowing through the cir cuit This phenomenon constitutes a technical feature of cooling devices and it does not signify their faulty work Steam precipitation on glasses of the device is a normal phenomenon in case of high relative air humidity exceeding 60 and does not require calling the service IGLOO 48 146621956 6 2 Service e Serial number NS ol Kaciniorea Wik 18 INFOQIGLOO COM PL IGLOO service telephone number Production date I DONIN MA 48 14 662 19 56 or 48 605 606 071 e Type name of the device MASA 153 00 ka e mail serwis igloo p and NAPI CIE ZNAM 230V 50Hz If after checking points described in chapter e Date when the device was e
14. nstant working mode is activated Diode 2 is on Ventilator the symbol is visible when evaporator ventilators are turned on It blinks when the actuation of the ventilators is delayed by external disengagement or when another procedure is in progress Diode 3 is on Defrosting the symbol is visible when the defrosting function is activated It blinks when the actuation is delayed by external disengagement or when another procedure is in progress Diode 4 is on Alarm the symbol is visible when the alarm is activated 5 current temperature inside the device is displayed decimal places displayed after the comma SETTING THE DESIRED TEMPERATURE my press for 1 second etf leading value shall be displayed on the screen A increase or decrease the leading value by means of yet and switches until the desired value shall be obtained press once again in order to confirm the new value of the setting point MANUAL INPUT OF THE DEFROSTING CYCLE Defrosting shall be realised in an automatic mode It is possible to force defrosting at any moment by pressing and holding the yt switch for minimum 5 seconds Diode No 1 shall blink during manual defrosting Read more on www alfaco pl NOTE IN CASE OF NOT OBSERVING THE PRINCIPLES ON CONNECTING AND USING THE DEVICE INCLU DED IN THIS MANUAL THE PRODUCER SHALL RESERVE THE RIGHT TO RECEDE FROM OBLIGATIONS OF THE GUARANTOR Information included in this document may be altered by IGLO
15. p conduit to the back of the glass side in order to hide the conduit coming out of the lamp in the casing and to place it on the internal part of the glass side 5 Mount front screen Fig 4 8 p 14 6 Mount front glasses of the display cabinet Fig 4 5 p 14 7 Mount night screens Fig 5 1 2 p 15 8 Place the condensate container according to Fig 6 2 p 15 does not concern devices with evaporator e The first cleaning of the device should be provide right after unpacking and before turning it on The unit should be cleaned with water at a temperature not exceeding 40 C with a neutral detergent For washing and cleaning the equipment it is prohibited to use products containing chlorine and sodium varieties which destroy the protecti ve layer and components of the device Any residue of adhesives or silicone on metal elements should be remo ved only with extraction naphtha not applicable to items made of plastic Do not use other organic solvents When cleaning the unit is prohibited to use water jet The unit should be cleaned with a wet rag After installation of the device at the destination place it should be left to rest for at least 2 hours before turning it on for devices with built in compressor to set the level of refrigerant in order to prevent problems with starting up the aggregate WARNING Keep out the cooling circuit from damage e Place the plug of the connecting cable directly in plug in socket it is forbi
16. rm 13 2 Ne UNDO SE n yeaa e a E kaa tesciats 11 Fig 3 Assembly of display hElV 14 2 2 Description Of the devige 11 Fig 4 Assembly of glass elements and aluminium lamp 14 2 3 Je hni al 8 Fo ne 12 Fig 9 Assembly disassembly of night SCree Ns nnn 15 3 PREPARING THE DEVICE FOR EXPLOITATION 13 Fig 6 Condensate Container oo nnnnnanunninnnnnnnounnnnnne 15 3 1 Requirements concerning the place of installation 13 Fig 7 ntrol panel 15 3 2 Connection and a tuation 13 Fig 8 Front glass disassembly 16 4 EXPLOITATION 15 Fig 9 Temperature sensor inside the devige 16 4 1 Temperature regulation oo cccumunnnunnnninnnnnnnninnine 16 Fig 10 Cleaning the CONdeNSe Eo ccmmumunuunnnnninnnnnnnnn 17 3 MAINTENANCE schon pnaceoouenmiand tanaidbemamntitee 16 Fig 11 Changing the fluorescent lamp 17 3 1 Cleaning and MAINTENANCE oo cccumunnnniunnnnninnnne 16 Fig 12 Data plate 18 6A SERVICE T ara e meee E EN 17 Fig 13 gloo thermostat control panel 19 6 1 Fault identification and repai 17 Fig 14 Carel thermostat control panel 20 6 2 CIVICS n aaan Ea E enscdn 18 7 THERMOSTAT SERVICE ocommmmommnmunmunmummunne 19 L st of tabl es T1 al GLQ Q thermostat 19 Ted GARELL thermostat spies ttc nce te erence 20 Table 1 Technical data 12 This sign signifies information of particular meaning for user security and for proper device e exploitation www igloo pl User manual Monika 2 Rota 11
17. s twice bigger than the one stated in the table 12 User manual Monika 2 Rota 3 PREPARING THE DEVICE FOR EXPLOITATION 3 1 Requirements concerning the place of installation e Verify whether the cross section of feeding conduits is proper for power consumption of the installed device e It is forbidden to connect the device by extension rods or dividers e The device should be connected to the separate properly made electric circuit with plug in socket with protecting pin according to PBUE Regulations concerning Electric Equipment Construction The device may be actuated solely after confirmation of the fire protection efficiency with results of measu e res performed according to binding regulations 3 2 Connection and actuation e Unpack the device and remove the wooden platform from the basis Fig 2 p 13 e Place the device on an even and on a sufficiently hard base and then level it with the help of levelling feet e Remove the protection foil from the elements of the device f ex from the inside of the device display shelves and front fender beam e If the user shall obtain a device partially disassembled to secure it during transportation perform the following ope rations 1 Mount display shelves Fig 3 1 p 14 2 Mount glass sides Fig 4 2 1 p 14 3 Mount the aluminium lamp together with lighting on glass sides Fig 4 3 p 14 4 Mount the casing of lamp conduit Fig 4 10 p 14 Move the casing of lam
18. the lighting is on Make sure that e The main switch is on Temperature setting on the thermostat is properly set Thermostat works properly The condenser is clean if necessary clean the condenser e Ambient temperature does not exceed 25 C Enough time has passed for products to be cooled e Ventilation holes of the device are not blocked This concerns the IGLOO thermostat thermostat displays CO or C1 or C2 instead of displaying temperature This situation shall occur when one of temperature regulation sensors has been destroyed The following messages may be displayed in such case e C0Q temperature sensors inside the chamber are damaged call authorized service e C1 failure of evaporator sensor call authorized service e C2 failure of condenser alarm sensors or failure of second evaporator sensor call authorized service This concerns the CAREL thermostat Thermostat displays E0 or E1 or LO or HI or EE or Ed or DF instead of temperature e 0 failure of temperature sensor inside the chamber call authorized service e 1 failure of evaporator sensor call authorized service LO low temperature alarm lower than temperature range set within the device call authorized service e HI high temperature alarm call authorized service e EE internal defect of the regulator call authorized service e Ed max defrosting time exceeded DF defrosti
Download Pdf Manuals
Related Search