User Manual Find`n`Secure Starter Kit
Contents
1. press the black button for 16 seconds without releasing it 1 You should see Please wait 16 sec Dont press any button appear in the LCD Ignore the warning 2 Now type the following sequence of buttons in the LCD where 1 WHITE and 2 GREY 2122 1211 12 3 After this you should see Reconfigure to SMS White YES Grey NO 4 Then press the WHITE button in the LCD to switch back to SMS After this the vehicle unit will revert back to SMS mode Appendix B Procedure to create a free account with DynDNS To create a free account go to httos www dyndns org account create html Complete all requested data and put a valid email address to be able to activate the account Then Click CREATE ACCOUNT You will receive an email with instructions to activate the account just follow the instructions to proceed Login to your account by going to https www dyndns org account login html Create your own Dynamic DNS Host by going to https www dyndns org account services hosts dyndns add htm Select your own Domain Name Base for example yourcompany gt dynalias net Then click Add Host and you re done Logout to finish After creating an in DynDNS above then you will need to update the IP address of the server using an update client like DynDNS updater which can be downloaded from http www dyndns com support clients Embarc Information Technology P Ltd 2007 www findnsecure com Page 142. Also the unit will send an alert when the brown cable is disconnected Embarc Information Technology P Ltd 2007 www findnsecure com Page 11 Find n Secure Starter Kit User Manual B Outputs 1 There are three outputs in this vehicle unit Two outputs Blue wire and orange wire source 5mA current and the third output white wire is able to sink 200mA current Below is the circuit diagram for output A and output B Since the Blue or orange wire sources around 5MA current it cannot drive a relay directly hence it needs to be amplified The below circuit amplifies the signal from blue or orange wires to one which is good enough to drive a relay The output can be used to either blow horn or open doors in cars having central locking feature or any other use which can be thought of Diode IN4148 Z5 12V NC Relay Blue Orange Wire 10 K Resistor Circuit Diagram for Output A B Embarc Information Technology P Ltd 2007 www findnsecure com Page 12 Find n Secure Starter Kit User Manual 2 Below is the wiring diagram for ignition kill The ignition circuit is bypassed and connected via a 12V relay The relay is normally closed and the circuit is complete When the ignition block command is issued from web or mobile the white wire causes the relay to energise and the connection opens to kill the engine On issuing the ignition unblock command from web or mobile the relay de energises and the connection closes thereby
3. User Manual Find n Secure Starter Kit Embarc Information Technology P Ltd 39 Old Vijay Nagar Colony Agra 282 004 India Tel 91 562 2857222 E Mail info findnsecure com Web www findnsecure com UK 44 20 81449750 Phone 44 70 06035630 Fax Find n Secure Starter Kit User Manual Copyright August 15 2007 Embarc Information Technology P Ltd All rights reserved Embarc Document Printed in India Notice This manual as well as the software described in it is furnished under license and may be used or copied only in accordance with the terms of such license The content of this manual is furnished for informational use only is subject to change without notice and should not be construed as a commitment by Embarc I T P Ltd Embarc I T P Ltd assumes no responsibility or liability for any inaccuracies that may appear in this book Embarc I T P Ltd reserves the right to make changes to specifications at any time and without notice The information furnished by Embarc I T P Ltd in this publication is believed to be accurate and reliable however Embarc I T P Ltd assumes no responsibility for its use or for infringements of patents or other rights of third parties resulting from its use No license will be granted under any patents or patent rights owned by Embarc I T P Ltd Check for updated version of user manual at www findnsecure com downloads starterkit_manual pdf Embarc Infor
4. eat steps 7 to 10 for other vehicle units if required 20 When completed press Done Embarc Information Technology P Ltd 2007 www findnsecure com Page 10 Find n Secure Starter Kit User Manual Testing in the vehicle To test in the vehicle the wiring cable is to be used The red and black wires are to be connected to the positive and negative terminal of the car battery The 15 Pin D type connector should be connected to the vehicle unit and LCD display should also remain connected The GPS antenna can be kept on the car roof during testing The vehicle should be taken around and it should report on the software moving in real time Read the user manual of Find n Secure for more details on the software You can download it from here Wiring Diagrams for Model FS 11 A Triggers 1 Below is the wiring diagram to connect the optional battery Z Event When the red cable is disconnected from 12V terminal the unit sends a Z Event to the base station Also the unit will send an alert when the red cable is reconnected 12V 32AH y BA Diode Main Battery To Violet wire Circuit Diagram for Optional Battery 2 Y Event Connect the green cable to the ve terminal of the battery and the unit will send a Y event to the base Also the unit will send an alert when the green cable is disconnected 3 X Event Connect the brown cable to the 12V terminal of the battery and the unit will send a X event to the base
5. mation Technology P Ltd 2007 www findnsecure com Page 2 Find n Secure Starter Kit User Manual Contents PA OC AAA 4 PACK reL ON OS a AA ee PA AS AN AA AA AA AAA 4 BEIO WA 0 Ic AAA 6 Configuration of Vehicle en ea baba an narasi 6 es ine un sn 11 AA en ana en aba an aa 11 Procedure to switch from GPRS mode to SMS mode oo Wooo Wah 14 Ap 0 21 8 Ba 14 Procedure to create a free account with DynDNS oo oooWo oo 14 Embarc Information Technology P Ltd 2007 www findnsecure com Page 3 Find n Secure Starter Kit User Manual Introduction Congratulations for purchasing the Find n Secure starter kit This kit will help you get going in no time to enable you to test the Find n Secure AVLS Automatic Vehicle Location and Security System Package Contents The starter kit contains the following items 1 Vehicle Unit Vehicle Unit Figure 1 2 LCD Display LOD Display 3 GPS and GSM Antenna Maura GPS Antenna GSM Antenna Figure 3 Embarc Information Technology P Ltd 2007 www findnsecure com Page 4 Find n Secure Starter Kit User Manual 4 Configuration Cable Contiguration Cable Figure 4 5 Wiring Cable Wiring Cable Figure 5 6 Panic Switch Panic Swidh jan Figure 6 7 Embarc Vehicle unit configuration utility YG Find n Secure ecuri Embarc Information Technology P Ltd 2007 www findnsecure com Page 5 Find n Sec
6. nfiguration Utility Select Configuration Mode Basic Settings SMS Mode VU Mobile 919897765511 ea f GPRS Made 2997026894 Com Port tay jile gt e g 919897012345 Vehicle unit successfully configured in GPRS mode Vehicle ID Please ens pos 40 Matero SMS Mode _ 3 3 ary 240 Seconds GPRS Settings Connection Settings Username Domain Name findnsecure selfip com Password DNS IP Ng APN Name airtelgprs com Local Port 21000 Dial Number fom Remote Port 21000 Send to VU Done Figure 14 12 but will not be able to do so because SIM is not Now it will try to connect to GPRS present inside the vehicle unit At this point power off the vehicle unit remove power adapter of configuration cable from mains open the four screws on the base of the vehicle unit insert the SIM and power on the vehicle unit from a 12V Battery using the provided black cable in which red wire is connected to 12V and Black wire connected to GND 13 To check whether vehicle unit has been properly configured once the vehicle unit has booted press black black button repeatedly and you should see displays similar to the following Embarc Information Technology P Ltd 2007 www findnsecure com Page 8 Find n Secure Starter Kit User Manual 14 The display in Figure 16 shows that GPRS has been connected OK Figure 16 15 Press black button again and you see a display simila
7. pplicable Leave local port and remote port as it is See Figure 12 Inform the domain name to us too 10 Click on Send to VU See Figure 13 Km les Find n Secure Initial Vehicle Configuration Utility NY Select Configuration Mode Basic Settings C SMS Mode YU Mobile 919897765511 ORRE Mode Base Mobile 919997026894 ComPot comt lt country code gt lt Mobile gt e g 919897012345 Vehicle ID 000002 Frequency Settings Minimum Displacement 40 Meters Please ensure Vehicle Unitis in SMS Mode before configuring Moving 20 Stationary 240 Seconds GPRS Settings Connection Settings Username Domain Name findnsecure selfip com Password DNS IP cc 7 APNName fairtelgprs com LocalPort 21000 Dial Number rog Remote Port 21000 Send to VU Done Figure 12 You will also see the vehicle unit restarting with ID changed to new one as shown below See Figure 15 Figure 15 Connection Settings BER m Domain Name DNS IP Provide the domain name of the i your ISP provides DNS Server mbia i IP address then place t in thes hast which is running the Meki Serves LocalMemote Ports These are the UOP port numbers used by the hosting server Figure 13 11 After few seconds you will see commands like SPB SPC etc on the LCD display and after that the vehicle unit will automatically restart and you will get the following screen See Figure 14 oO Find n Secure Initial Vehicle Co
8. r to the one shown in Figure 17 The number on top left 07 27 is the UTC Time lt STOP gt signifies that the vehicle is stationary at the moment the number on top right 0018 is the seconds till which it will wait before sending a data packet The number on bottom left 08 11 is the current date The number T 04 04 below lt STOP gt signifies the satellites visible figure 17 to the GPS antenna and 3D OK signifies that the GPS fix has been achieved 16 On pressing the black button again you will see the details of satellites visible as shown in Figure 18 Figure 18 Embarc Information Technology P Ltd 2007 www findnsecure com Page 9 Find n Secure Starter Kit User Manual 17 On pressing black button again you will get the latitude and longitude of the current location similar to the one shown in Figure 19 Figure 19 18 Press the black button again and you will get a display similar to the one shown in Figure 20 Figure 20 19 Press the black button once again and you will get a display similar to the one shown in Figure 21 In this there are two lines of display The first line shows UIP 117 96 10 212 assigned by the GSM operator it could be any number generally of the form 10 x x x and the second line shows BIP 122 160 144 32 which is the IP address of our server Figure 21 If you see display screens similar to above the vehicle unit would be properly configured Rep
9. st command received by the Figure 9 unit This will be useful to verify that there is communication between base and unit See Figure 10 5 Make sure that the vehicle unit is in SMS mode before attempting to configure it in GPRS mode XP GSM in Figure 9 confirms it is in SMS mode If you see XP GPRS instead it is in GPRS mode If it is in GPRS mode it needs to be reverted to SMS mode first as per procedure given in Appendix A 6 Start the Embarc Vehicle unit configuration utility on the PC and select GPRS mode Select the correct COM port 7 Enter vehicle id six digit number Figure 10 assigned by Find n Secure AVL software or sent by us VU GPRS Settings Mobile and Frequency settings Usemame UsernamePossword i e Username Password Enter Username if applicable Password provided by the ISP for Be WEZA GPRS connectivity password if applicable APN Banas _ name Dial number if different Dial Number Mao See Figure 11 T 8 APA Name Dial Number Access Point Name Dial out number for GPRS provided by the ISP for Connectivity Mosily the GPRS connectivity dialing number is Io 2 bad if our provider USES miry other number you can Specity here Figure 11 Embarc Information Technology P Ltd 2007 www findnsecure com Page 7 Find n Secure Starter Kit User Manual 9 Enter Domain created using www DynDns org DNS IP if a
10. te account with DynDns is given in Appendix B You can update the ip using DynDns updater or any similar utility Use manual update option for the starter kit with ip as 122 160 144 32 IP of our server DNS IP Provided by carrier If the carrier doesn t give leave in blank and unit will auto detect it Normally it is left as blank only Install the Embarc Vehicle Unit Configuration Utility supplied on CD on any PC running Windows XP Vista and having active internet connection The PC should also have a free COM port either COM1 or COM2 Configuration of Vehicle unit 1 2 1 As A Aa Connect LCD display to the vehicle unit Figure 8 Connect the GSM antenna short antenna and the GPS antenna to the appropriate connectors of the vehicle unit See Figure 9 with the non magnetic side of the GPS antenna facing the sky Figure 8 Embarc Information Technology P Ltd 2007 www findnsecure com Page 6 Find n Secure Starter Kit User Manual 3 Connect one end of the configuration cable to the COM Port COM1 or COM2 as the case may be of the PC and the other end to the 15 Pin D type connector of the vehicle unit and the power adapter of the configuration cable to mains and power on You will see on the LCD display as shown in Figure 9 4 In the vehicle unit s LCD press the black button until you see PA in the first line and Op in the second line which refers to the la
11. the ignition circuit is again complete To White Wire lemition circuit 12V NC Relay 12 from Ignition Key Mi R amp Circuit Diagram for Ignition Kill Trouble Shooting 1 No display on LCD Check whether the connector has been inserted in the right direction Also check whether the male female connectors mating have happened correctly 2 GPRS Not Connected This could be for variety of reasons a The GSM Antenna not connected to the connector near the GSM board b The SIM is not GPRS enabled To confirm this insert the SIM in a mobile phone and see whether you are able to surf the internet or not c APN information is not correct Check the same from GSM provider d Username Password Check the same from GSM provider e Try using SIM from any other GSM provider if available f Area where you are working does not have proper GSM coverage g After configuring the vehicle unit should be run on a 12V battery or a bigger power source using the black cable 3 Pos Hold or No Position The GPS Antenna should be placed such that the black curved surface should face the clear sky 4 No report on software Take the unit around in a vehicle and then see Also check whether vehicle id is correct Embarc Information Technology P Ltd 2007 www findnsecure com Page 13 Find n Secure Starter Kit User Manual Appendix A Procedure to switch from GPRS mode to SMS mode When the LCD is not showing Connecting
12. ure Starter Kit User Manual Before you start Before you proceed for the configuration of the vehicle unit following information should be known 1 2 3 4 5 6 7 8 9 Mobile no of the SIM for the vehicle unit The SIM should be preferably post paid GPRS enabled SIM with sufficient credit Vehicle id This vehicle id number will normally be automatically generated by the Find n Secure AVL software on adding vehicle units to groups or you can even have user defined vehicle ids We will send you the vehicle id separately for the starter kit Frequency You need to decide the frequency at which data packets are to be sent when the vehicle is in motion minimum displacement in meters before data packet is sent and the frequency at which data packets are sent when the vehicle is stationary The default value is 20 sec while moving 240 sec while stationary and 40 m minimum displacement Default values should normally be used GPRS username It is provided by the GSM provider In some cases there is no username Leave blank in that case GPRS password It is provided by the GSM provider In some cases there is no username Leave blank in that case APN Name APN Access Point Name is provided by the GSM provider Dial Number It is generally 99 1 but in vehicle units having Ericsson mobile phones it is Domain You have to create an account with www DynDns org and enter that here Procedure to crea
Download Pdf Manuals
Related Search