Manual - MTL Instruments Group
Contents
1. see the WIO 900L Installation Manual 2 Reset the transmitter and receiver units to the factory default configurations 3 Link the transmitter and receiver units to work as a dedicated pair 4 Bench test your configuration before deploying NOTE You can also configure your network using a user defined customised configuration that lets you set specific information about your network For more information on setting a user defined customised configuration see the WIO 900L User Manual on the enclosed CD 2 Factory default configuration When you configure the units using the configuration in this document the inputs from the transmitter are sent to the outputs at the receiver as follows Digital Input 1 __ Digital Output 1 Digital Input 2 Bigita Output 2 Analogue Setpoint La Digital Output 3 Analogue input 4 20 mA Analog output 4 20 mA Thermocouple Input Not used px Communication Failure Comes on if no messages Setpoint Output Local indication from WIO 900LT System OK On if system OK BENE System OK On if system OK QSG 900LR 1 7 Oct 2010 3 Unit components and connections Your WIO 900LR receiver unit has the following components and terminal connections lH A Earth ground wire lug on underside POWER SUPPLY SYSTEM OK COMMS FAIL COMMON e 8 oO AO e o E NOT USED NOT USED e N a o o o a a l 29339082 Max 30V DC 500mA For inductive loa2. areas the power supply must be approved for Class 1 Div 2 use WARNING Explosion hazard do not connect or disconnect while circuit is live unless area is known to be non hazardous High sensitivity FHSS UHF radio receiver Frequency 902 928 MHz Actual frequency range depends on country 110dBm At PER 8 MTL Instruments Pty Limited 9 12 Billabong Street Stafford Queensland 4053 Australia Tel 61 1300 308 374 Fax 61 1300 308 463 E mail enquiries mtlaus com au Cooper Electric Shanghai Co Ltd Room 2001 China Life Tower 16 Chao Yang Men Wai Street Chao Yang District Beijing China 100020 Tel 86 10 5980 0288 Fax 86 10 8562 5725 E mail bjsales mtl inst cn MTL Instruments sarl Les Carr s du Parc 10 rue des Rosi ristes 69410 Champagne au Mont d Or France Tel 33 0 4 78 64 98 32 Fax 33 0 4 78 35 79 41 E mail infoGmtl inst fr MTL Instruments GmbH An der G mpgesbr cke 17 D 41564 Kaarst German Tel 49 0 2131 718930 Fax 49 0 2131 7189333 E mail info mtl de MTL India No 36 Nehru Street Off Old Mahabalipuram Road Sholinganallur Chennai 600 119 India Tel 91 0 44 24501660 24501857 Fax 91 0 44 24501463 E mail sales mtlindia com MTL Italia srl Via Cantt 11 20092 Cinisello Balsamo MI Italy Tel 39 0 2 61802011 Fax 39 0 2 61294560 E mail info mtl inst it Group Internet home page http www mtl inst com Members of The M
3. further 60 seconds press and hold the RSSI push button for 5 seconds until the LEDs stop flashing and then release 6 The WIO 900LR receiver lights all LEDs for 2 seconds before returning to normal operation NOTE If the LEDs do not light you must repeat the process from step 1 until the LEDs light before continuing 7 You can now link the transmitter and receiver units QSG 900LR 1 7 5 Oct 2010 6 Linking your transmitter and receiver units You must reset the transmitter unit to factory defaults to disable encryption before linking the transmitter and receiver units For more information see the WIO 900LT Transmitter Quick Start Guide NOTE You must complete the linking process in 60 seconds To link the transmitter and receiver units 1 Press and hold down the RSSI Pushbutton on the receiver 2 Power on the receiver while holding down the RSSI Pushbutton 3 Release the RSSI Pushbutton as soon as the Receiver LEDS flash within 5 seconds of powering the receiver 4 The receiver will flash all LEDs for a maximum 60 seconds while it tries to link to the transmitter 5 Power on the transmitter The transmitter sends a special Link message to allow the receiver to recognise the transmitter 6 When the units link the receiver lights all LEDs for 2 seconds before returning to normal operation NOTE If the receiver LEDs continue flashing within the 60 seconds the units are not linked and you should retry
4. the linking process by powering the transmitter off and on again If you exceed the 60 seconds you must restart the linking process from step 1 You can now bench test your configuration before deploying 7 Safety information Thank you for selecting the WIO 900LR receiver for your telemetry needs We trust it will give you many years of valuable service To ensure your WIO 900LR receiver enjoys a long life double check ALL your connections with the user s manual before powering on the unit WARNING Incorrect termination of supply wires may cause internal damage and will void warranty Exposure to RF energy is an important safety consideration The FCC has adopted a safety standard for human exposure to radio frequency electromagnetic energy emitted by FCC regulated equipment as a result of its actions in Docket 93 62 and OET Bulletin 65 Edition 97 01 FCC Notice when used in USA WIO 900LR Wireless I O Module This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part15 of the FCC rules Code of Federal Regulations 47CFR Part 15 Operation is subject to the condition that this device does not cause harmful interference This device has been type accepted for operation by the FCC in accordance with Part90 of the FCC rules 47CFR Part 90 See the label on the unit for the specific FCC ID and any other certification designations QSG 900LR 1 7 Oct 2010 QSG 9OOLR 1 7 Oct 2
5. 010 Industry Canada WIO 900LR Wireless I O Module RSS 119 This device has been type accepted for operation by Industry Canada in accordance with RSS 119 of the Industry Canada rules See the label on the unit for the specific Industry Canada certification number and any other certification designations NOTE Any changes or modifications not expressly approved by MTL could void the user s authority to operate this equipment To operate this equipment legally the user must obtain a radio operating license from the government agency This is done so the government can coordinate radio users in order to minimize interference Safety information FCC Notice This device complies with Part 15 247 of the FCC Rules Operation is subject to the following two conditions This device may not cause harmful interference and This device must accept any interference received including interference that may cause undesired operation NOTE This equipment is suitable for use in Class 1 Division 2 groups A B C and D or non hazardous locations only 8 Unit specifications Digital outputs Voltage free contacts rated at 250 VAC 1A 30VDC 1A 2 for digital inputs and 1 for setpoint Status outputs 2 Separate System OK and communication failure output Analog output 1 16 bit resolution 0 196 accuracy single ended source output Power supply 1 9 30 VDC 0 25 Amp CSA certified Class 2 power supply For use in Class 1 Div 2 hazardous
6. TL Instruments Group Cooper Crouse Hinds Japan KK MT Building 3F 2 7 5 Shiba Daimon Minato ku Tokyo Japan 105 0012 Tel 81 0 3 6430 3128 Fax 81 0 3 6430 3129 E mail sales mtlkk co jp Cooper Crouse Hinds Korea 12F Vision Tower 707 2 Yeoksam dong Gangnam gu Seoul 135 080 South Korea Tel 82 2 3484 6795 Fax 82 2 3484 6778 MTL Instruments BV MTL Instruments BV Terheijdenseweg 465 4825BK Breda The Netherlands Tel 31 0 76 7505360 Fax 31 0 76 7505370 E mail info mtlbenelux com Cooper Crouse Hinds Pte Ltd No 2 Serangoon North Avenue 5 06 01 Fu Yu Building Singapore 554911 Tel 65 6 487 7887 Fax 65 6 487 7997 E mail sales mtlsing com sg MIL Instruments Villa No 4 Sector 2 17 Street 6 PO Box 53234 Abu Dhabi UAE Tel 971 2 446 6840 Fax 971 2 446 6841 E mail mtlgulf mtlinst com Measurement Technology Limited Great Marlings Butterfield Luton Beds England LU2 8DL Tel 44 0 1582 723633 Fax 44 0 1582 422283 E mail enquiry mtl inst com Cooper Crouse Hinds MTL Inc 3413 N Sam Houston Parkway W Suite 210 Houston TX 77086 USA Tel 1 281 571 8065 Fax 1 281 571 8069 E mail csinfo mtl inst com
7. WIO 900LR wireless I O receiver unit Quick Start Guide QSG 900LR ABOUT THIS DOCUMENT This is the Quick Start Guide for the MTL WIO 900LR Wireless I O Receiver Unit and contains the M iain sections Section Read this section if youwantto this section if you want to Basic steps for Learn the basic steps for retain and using UA S RN Factory default Understand how the transmitter sends DE CANNE S NN DIT UM on T IM Resetting factory Reset your unit to the original factory default defaults settings 16 Linking Tx and Rx units Link your units to work as a dedicated pair Understand important safety information related to your unit NOTE You must read this information before installing your unit 8 Specifications See the technical information For more information see the following sections 7 Safety information 1 Basic steps for using your unit This document describes how to configure your unit using the default factory configuration that lets you easily setup your network as a simple send receive network using a dedicated pair of transmitter and receiver units The basic steps for using your unit are 1 Connect the antenna power supply and transducer signals using the instructions in this document Power supply and transducer connection is described in the section Unit components and connections Antenna connection is described in the section Antenna installation For more information
8. d use surge diodes m n SNO M ANALOG OUPUT LOAD Max analog load 900 ohms DO contacts are rated at 1A 250VAC POWER SUPPLY For good engineering practice use 9 30V DC a surge diode for DC loads and 250mA 12V a surge capacitor 10nF 250V for AC loads 125mA 24V IMPORTANT ELECTRICAL SAFETY INFORMATION WARNING In order to comply with Electrical Safety Regulations this module must be installed in an Electrical AND Fire enclosure This enclosure may be a single or multiple enclosures Access to the module is to be made by a Service Person only In order to comply with Electrical Safety Standards when connecting SELV AND voltages which are greater than SELV 30VAC or 60VDC together then Relay Output 2 must NOT be used in order to provide sufficient isolation between the outputs QSG 9OOLR 1 7 Oct 2010 The front panel provides the following components mlt SMA antenna connector el at top of unit WIO 900LR D ok D1 D2 D D3 DRX CF RS232 configuration port RSSI push button The LEDs on the front panel indicate the unit status Current status of the unit OK OK Red Fault condition detected in unit Receiving Message CF ON Module Communication Failure Output is active PGON o Configuration Cable Connected D1 D2 D3 ON LEDs with RSSI Push Button Pressed Output LED flashing quickly The Output LEDS D1 D2 D3 light when the corresponding o
9. utput is active Relay output D1 is ON i e contact closed Relay Output D2 is ON Relay Output D3 is ON When you press the RSSI push button the unit shows the signal strength by lighting the LEDs from the bottom to the top Signal strength is the strength of the last message received that was addressed to this station Signal Strength Signal Strength Better than 85 dBm Better than 100 dBm Better than 90 dBm Better than 105 dBm Better than 95 dBm Always on during RSSI test QSG 900LR 1 7 Oct 2010 4 Antenna installation 1m minimum Objects e g walls Collinear antenna Weatherproof connectors e g 3M 23 tape etc Surge protector arrestor optional Stress relief loop Mast Rx unit Ground Stake A good ground connection must be provided to the mast unit and surger arrestor protector A The antenna must be be installed above all local obstructions 5 Resetting your unit to factory defaults You must reset the receiver unit to factory defaults before linking the transmitter and receiver units To reset the default factory configuration 1 Press and hold the RSSI push button 2 Power on the WIO 900LR receiver 3 The WIO 900LR receiver flashes all LEDs at medium flash i e 1 6 Hz NOTE If the LEDs do not flash you must repeat steps 1 and 2 until the LEDs flash before continuing 4 Release the RSSI push button within 5 seconds 5 Within a
Download Pdf Manuals
Related Search