USER MANUAL - Dialighting
Contents
1. Operate the device only after having become familiar with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Please use the original packaging if the device is to be transported Please consider that unauthorized modifications on the device are forbidden due to safety reasons If this device will be operated in any way different to the one described in this manual the product may 3 6 USER MANUAL PROFILE LIGHT 19 26 36 50 suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock lamp explosion crash etc INSTALLATION Installing Replacing the lamp DANGER TO LIFE Only install the lamp with the device switched off Unplug from mains before The lamp has to be replaced when it is damaged or deformed due to the heat CAUTION Before replacing the lamp unplug mains lead and let the lamp cool down approx 5 minutes During the installation do not touch the glass bulbs bare handed Please follow the lamp manufacturer s notes Do not install lamps with a higher wattage Lamps with a higher wattage generate temperatures the device was not designed for Damages caused by non observance are not subject to warranty During the operation the lamp reaches temperatures of up to 800 C For the installation you need a 240V 575W GX 9 5 lamp Procedure2. a normal process and does not necessarily mean that the device is defective Caution During the operation the housing becomes very hot Do not switch the device on and off in short intervals as this would reduce the lamp s life HEALTH HAZARD Never look directly into the light source as sensitive persons may suffer an epileptic shock especially meant for epileptics Keep away children and amateurs OPERATING DETERMINATIONS This device is a spot designed for professional use on stages in discotheques theatres etc This fixture is only allowed to be operated with an alternating current of max 230 V 50 60 Hz and was designed for indoor use only Lighting effects are not designed for permanent operation Consistent operation breaks will ensure that the device will serve you for a long time without defects Do not shake the device Avoid brute force when installing or operating the device When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust There should not be any cables lying around You endanger your own and the safety of others The minimum distance between light output and the illuminated surface must be more than 2 meters Make sure that the area below the installation place is blocked when rigging derigging or servicing the fixture Always fix the fixture with an appropriate safety rope The maximum ambient temperature t 45 C must never be exceeded
3. SPOT575 750 750 Profile Spot starts running CLEANING AND MAINTENANCE The operator has to make sure that safety relating and machine technical installations are inspected by an expert after every four years in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are inspected by a skilled person once a year The following points have to be considered during the inspection 1 All screws used for installing the devices or parts of the device have to be tighly connected and must not be corroded 2 There must not be any deformations on housings fixations and installation spots ceiling suspension trussing 3 The electric power supply cables must not show any damages material fatigue e g porous cables or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed DANGER TO LIFE Disconnect from mains before starting maintenance operation 6 6 USER MANUAL PROFILE LIGHT 19 26 36 50 We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents CAUTION The lens has to be replaced when it is obviously damaged so that its function is impaired e g due to cracks or deep scratches The objective lens will require weekly cleaning as smoke fluid tends to building up residues reducing the light output very
4. Step 1 Unscrew the knurled screw of the lamp housing Step 2 Remove the lamp housing from the device Step 3 If replacing the lamp remove the old lamp from the socket Step 4 If the lamp base is the same as shown in figure 1 then insert the 240V 575W GX 9 5 lamp into the lamp socket Step 5 If the lamp base is the same as shown in figure 2 then first remove the retention box before inserting the new lamp Save the retention box for furture use Step 5 Replace the lamp housing onto the device and tighten the screw Do not operate this device with opened lamp housing Lamp adjustment The lampholder is aligned at the factory Due to differences between lamps fine adjustment may improve light performance Strike the lamp open the shutter and the iris set the dimmer intensity onto 100 and focus the light on a flat surface wall Center the hot spot the brightest part of the beam using the 3 adjustment screws A B C Turn one screw at a time to drag the hot spot diagonally across the projected image If you cannot detect a hot spot adjust the lamp until the light is even To reduce a hot spot pull the lamp in by turning all three screws A B C clockwise 4 turn at a time until the light is evenly distributed If the light is brighter around the edge than it is in the center or if light output is low the lamp is too far back in the reflector Push the lamp out by turning the screws A B C counterclockwise 1 tur
5. USER MANUAL PROFILE LIGHT 19 26 36 50 C Show Atelier DIALighting Profile Light 19 26 36 50 VAN oam S ae 4 HPL 750W S575W Gobo holder Iris Double color PGE ORDER ORDER PACKING FAL na 1 6 USER MANUAL PROFILE LIGHT 19 26 36 50 USER MANUAL PROFILE LIGHT 575 750 TECHNICAL SPECIFICATIONS Power supply 230 V AC 50 Hz Power consumption 590 W 800W Dimensions LxWxH 650 x 180 x 260 mm Weight 6 kg Fitting lamp HPL575W HPL750W Maximum ambient temperature ta 45 C Maximum housing temperature ts steady state 245 C For your own safety please read this user manual carefully before you initially start up Every person involved with the installation operation and maintenance of this device has to be qualilfied follow the instructions of this manual consider this manual to be part of the total product keep this manual for the entire service life of the product pass this manual on to every further owner or user of the product include every supplementay update with the original manual INTRODUCTION Thank you for having chosen a PROFILE SPOT575 750 Profile Spot Unpack your spot Before you initially start up please make sure that there is no damage caused by transportation Should there be any consult your dealer and do not use the device SAFETY INSTRUCTIONS CAUTION Be careful with your operations With a dangerous voltage you can suffer a dangerous electric shock w
6. hen touching the wires This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature This device falls under protection class The power plug must only be plugged into a protection class outlet 2 6 USER MANUAL PROFILE LIGHT 19 26 36 50 Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution Make sure that the available voltage is not higher than stated on the rear panel Make sure that the power cord is never crimped or damaged by sharp edges Check the device and the power cord from time to time Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During the initial start up some smoke or smell may arise This is
7. n at a time the light is bright and evenly distributed Focusing Step 1 Loosen the focus button on the underside of the device 4 6 USER MANUAL PROFILE LIGHT 19 26 36 50 Step 2 Adjust the focus by sliding the lenshousing forward or backward Step 3 Tighten the focus button Overhead rigging DANGER TO LIFE Please consider the EN 60598 2 17 and the respective national norms during the installation The installation must only be carried out by an authorized dealer The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment e g an appropriate catch net This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails When rigging derigging or servicing the fixture staying in the area below the installation place on bridges under high working places and other endangered areas is forbidden The operator has to make sure that safety relating and machine technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time The operator has to make sure that safety relating and machine technical installations are approved by an expert after every four year in the course of an acceptance test The o
8. ng bracket has a diameter of 10 mm For overhead use always install a safety rope that can hold at least 12 times the weight of the fixture You must only use safety ropes with quick links with screw cap Pull the safety rope through the hole in 5 6 USER MANUAL PROFILE LIGHT 19 26 36 50 the mounting bracket and over the trussing system or a safe fixation spot Insert the end in the quick link and tighten the safety screw The maximum drop distance must never exceed 20 cm A safety rope which already hold the strain of a crash or which is defective must not be used again Adjust the desired inclination angle via the mounting bracket and tighten the fixation screws Connection with the mains DANGER TO LIFE The electric connection must only be carried out by a qualified electrician In order to connect the device to the mains you have to install a power plug The occupation of the connection cables is as follows Cable Pin__ International Brown itive Brown Live Blue Neutral N pene Pe ie ___ The earth has to be connected Connect the device to the mains with the power plug If the device will be directly connected with the local power supply network a disconnection switch with a minimum opening of 3 mm at every pole has to be included in the permanent electrical installation Lighting effects must not be connected to dimming packs OPERATION After you connected the effect to the mains the PROFILE
9. perator has to make sure that safety relating and machine technical installations are approved by a skilled person once a year Procedure The projector should be installed outside areas where persons may walk by or be seated IMPORTANT OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE including but not limited to calculating working load limits installation material being used and periodic safety inspection of all installation material and the projector If you lack these qualifications do not attempt the installation yourself but instead use a professional structural rigger Improper installation can result in bodily injury and or damage to property The projector has to be installed out of the reach of people If the projector shall be lowered from the ceiling or high joists professional trussing systems have to be used The projector must never be fixed swinging freely in the room Caution Projectors may cause severe injuries when crashing down If you have doubts concerning the safety of a possible installation do NOT install the projector Before rigging make sure that the installation area can hold a minimum point load of 10 times the projector s weight DANGER OF FIRE When installing the device make sure there is no highly inflammable material decoration articles etc within a distance of min 0 5 m Mount the projector with the mounting bracket to your trussing system using an appropriate clamp The hole in the mounti
10. quickly The venting slots should be cleaned monthly The interior of the device should be cleaned at least annually using a vacuum cleaner or an air jet There are no serviceable parts inside the device except for the lamp Maintenance and service operations are only to be carried out by authorized dealers Please refer to the instructions under Installing Replacing the lamps Should you need any spare parts please use genuine parts If the power supply cable of this device becomes damaged it has to be replaced by authorized dealers only in order to avoid hazards Should you have further questions please contact your dealer 7 6
Download Pdf Manuals
Related Search