Home

Orbea Avant User Manual

1. Installing brake cable The installation of the cable in Cantilever brakes requires specific tools and know how Therefore it should be done by an authorized dealer Determine the reach of the old cable loosen the brake cable anchor bolt and disassemble the old cable Grease the new cable and install it positioning it with the same reach as the old cable Check that the end of the cable is well secured and properly adjust the housing f necessary follow the instructions for adjusting brake shoe alignment Turn the bolt clockwise so the shoe is not above or outside the rim Hold the shoes against the rim and tighten the bolt Cut the end of the cable so that only 5mm of cable overhangs from the bolt Attach an end cap to the end of the cable Follow the inspection and adjustment instructions Opening the brake to remove the wheels Note you must follow the inspection instructions in the wheels section to complete this installa tion For most brakes lift the brake release lever to the Open position To close it turn the lever to the Closed position For Cantilever and Caliper brakes release the straddle cable With one hand squeeze the brake shoes against rim and with the other pull the cable end cap away from the retention holder Once the shoes are released the brake will open To close the brake follow these ins tructions in reverse For V Brakes disconnect the
2. Stand over the horizontal tube of the bike with both feet on the ground With the front wheel on the ground turn the fork and the handlebar left to right and vice versa Watch listen and feel if the headset is tight or if it makes noise or gets stuck at certain points WARNING An improper adjustment of the headset could cause you to lose control and fall Make sure the headset is correctly adjusted prior to use ORBEA Adjustment Adjusting the headset requires special tools and specific skills Therefore it should only be performed by your authorized dealer Lubrication The headset must be lubricated once a year This requires special tools and specific skills There fore it should only be performed by your authorized dealer BRAKING SYSTEM The braking system allows you to reduce your speed a critical function of your bicycle This section will explain how to inspect adjust and lubricate your bicycle s brakes You should also read the specific information corresponding to each type of brake used Suggestions for all braking systems all systems The different types of brakes have different braking capacities If you are not satisfied or comfor table with your braking system talk to your authorized dealer With any braking system a failure in the adjustment maintenance or use of the brakes could cause you to lose control of the bicycle and suffer the consequences that could entail If
3. Rear hub Gear cable The drivetrain is sealed therefore it stays lubricated with little maintenance This section will explain how to inspect adjust and lubricate the internal drivetrain Inspection A well adjusted drivetrain is silent If it makes any noise when shifting or while you are pedaling the gear cable may need to be adjusted If the noise gets louder after adjusting it stop the bicy cle and analyze the origin of the noise If necessary take your bike to your authorized dealer Once a month make sure that the shifters are correctly adjusted In a Nexus 8 speed hub set the shift lever to 4 Check to be sure that the yellow setting lines on the cassette joint bracket and pulley are aligned Once a month check that the cables are not twisted rusted have any broken wires or frayed ends If you have any issues with the gear cable do not use the bicycle Change the gear cable or take it to your authorized dealer Adjustment Adjusting the rear drivetrain Set the shift lever to 4 Align the indicator on the pulley of the rear wheel hub with the cassette joint bracket If they cannot be aligned adjust the cassette cable tension to do so Move the lever to 1 and then to 4 and check the adjustment Changing the drivetrain cable Loosen the cable fixing bolt Unscrew the bolt and hold the fixing nut at the end of the cable Slide the fixing nut from the end of the cable forwards Make a note of
4. For a safer ride your bike wheels must be firmly secured to the fork and frame The wheels are secured by way of bolts or quick release mechanisms which allow you to install and remove wheels without tools Check the handlebar and stem for signs of fatigue or increased tension Carefully inspect the handlebar and stem for signs of fatigue scratches cracks dents deformi ties and discoloring If any part shows signs of fatigue or damage change it before riding your bike Likewise check that the handlebar ends and extensions are plugged Check the adjustment of the suspension Make sure that the suspension components are adjusted to your preference and that no sus pension element is at its limit The suspension system affects your bike s performance there fore proper adjustment is very important If the suspension system is compromised to a point where the fork is blocked you could lose control For more information about how to adjust the suspension system see the chapter on Inspection adjustment and lubrication of your bike or the manual for the suspension system that may have come with your bike Check the lighting system Inspect the angles and function of the front and rear lighting and signaling systems These should be kept clean to work properly Check the handlebar Make sure the stem and the handlebar are correctly positioned and tightened and that the bell is working properly Check the saddle The saddle m
5. ORBEA BLUE PAPERS TECHNICAL MANUAL GEOMETRY AND SPECIFICATIONS FRAME MATERIAL AND CARE PARTS AND HARDWARE CABLE SYSTEMS ORBEA WARRANTY ADDITIONAL INFORMATION CEA 9 AND SPEGIFIGATIONS 1 410 420 470 490 510 530 560 170 170 170 172 172 175 175 Seat tube Crank 2 Toptube 518 52 536 549 564 580 594 Stem 90 90 100 110 110 120 1510 3 Head tube 113 129 147 165 188 205 226 Handlebar 400 400 400 420 420 440 440 4 Chain stay 414 414 414 414 418 418 418 5 Wheelbase 978 980 985 994 1005 1014 1024 B Reach 363 367 371 378 383 392 400 lt 160 47 1 Stack 517 536 555 573 596 615 636 160 165 49 8 Seat angle Som Heh Wa 28 155 165 170 51 9 Head angle 71 2 71 4 71 89 722 72 57 I3 7352 170 175 55 175 180 53 55 180 185 SS 185 190 57 5190 60 Altura orientativa y que puede variar segun morfolo gia del usuario y preferencias geometricas y de uso AVANT TECHNICAL SPECIFICATIONS FRAME AND MATERIAL Orbea frames are carefully designed to be durable efficient and easy to maintain Avant tubes are stiff and light giving excellent steering precision and pe daling efficiency Avant carbon frame is extremely re sistant to corrosion making it perfect for road With only a minimum amount of maintenance it s easy to keep your Orc
6. Slide the wheel out of the fork ends Installing a wheel For the rear wheel rotate the chain to position it on the outermost cog Insert the wheel in the frame or fork making sure that the hub is well inserted in the fork ends Readjust the quick release or tighten the hub nut as explained in the wheels section Check the brakes and make sure they are well adjusted Spin the wheel and check that it is trued and spins freely without rubbing against anything Lubrication Grease the hubs once a year This process requires specific tools and special know how It should only be performed by an authorized dealer Lubricate the quick release lever with a synthetic lubricant ever year SCHRADER AND PRESTA VALVES There are two types of valves Schrader and Presta Follow the criteria below when inflating your tires Schrader valve remove the valve cap attach a pump with the proper head fitting for this type of valve and inflate the wheel Once inflated replace the cap so that the valve does not become dirty Presta valve Remove the cap if any Unscrew the valve stem lock nut and push down on the valve stem to free it up A small amount of air will be released Inflate the wheel using a pump with the proper head fitting After inflating tighten the valve stem lock nut TUBELESS WHEELS Some bicycles are equipped with a tubeless tire system This is made up of the tire a rim and a specific valve for use without an inne
7. Be careful when riding in wet conditions 38 10 Caring for your frame and fork sss 58 Be especially careful when riding off the asphalt sse 38 11 nnne LEE FEER E ntt EEE teer 58 38 MAINTENANCE SCHEDULE t 60 ERR 38 General recommendations eene nennen 38 ORBEA RECOMMENDATIONS scenerne 61 Keep your bike eene nnne nnne 38 ADDITIONAL QUALITY 61 Store your bike in an appropriate place 22 38 Protect your bicycle from thieves 39 Protect your bicycle from possible 39 Use the proper technique when shifting gears 39 Prevent the handlebar from striking the 39 ORBEA GUIDE TO USING YOUR BICYCLE A IMPORTANT READ AND FOLLOW THE INSTRUCTIONS IN THIS MANUAL BEFORE USING YOUR BICYCLE A bicycle is small means of transport that is less powerful than other vehicles therefore your safety cannot be stressed enough This chapter contains recommendations that will help you ride as safely as possible CONDITIONS FOR USE Not using your bicycle in line with the specified conditions for use would imply restrictions to your warranty Bicycles are designed to
8. Feel for any play or knocking that mi ght indicate a loose headset loose brake rotors or ca lipers or worn fork bushings TEST RIDE Take a quick ride up and down the street to make sure your bike is shifting and braking properly Listen for unusual noises AFTER A GRASH OR IMPACT Falling is part of riding and it s impossible to avoid minor accidents If you crash your Avant please make sure you are okay and seek medical attention if ne cessary If you are not injured you should check your bike before continuing 1 Inspect your frame and components for da mage Do not ride your bike if any problems are de tected WHAT TO LOOK FOR Inspect Frame and fork for evidence of cracking or bending If cracks are discovered discontinue use immediately Check the drivetrain and spin the wheels to make sure components are operating correctly If you discover damage to your components discontinue use imme diately Even if you don t find any damage pay careful at tention to the sound of your bike when you continue riding Unusual noises can be caused by cracks or other problems A well maintained bike will be quiet and free of creaks or squeaks Investigate and locate the source of any new noises ORBEA 0 2 Bring your bike to your Orbea dealer for pro fessional inspection Some damage can only be de tected by disassembling the bike to check for cracks or other signs of stress A crash or impact can put extraordinary
9. High pressure yields better performance on hard surfaces like asphalt while lower pressures are best for off road rides CAUTION Air hoses at gas stations inflate wheels too quickly and indicate inaccurate pressures Always use hand pumps to inflate your tires Check your brakes The brake lever on right side of the handlebar activates the rear brake and the lever on the left activates the front brake unless local legislation indicates otherwise Check that the front and rear brakes are working properly Orbea uses different types of brakes Rim brakes the brake levers are connected to brake shoes that squeeze the wheel rim Disc brakes the brake levers are connected to brake pads that squeeze the brake disc Drum brakes the brake levers are connected to the hub of the wheel by a cable and a mini mum of 15mm is needed to stop the bike ORBEA Coaster brakes the braking action is carried out by pedaling backwards Follow the inspection instructions for the type of brakes on your bike If your brake system does not pass the inspection specified in the Inspection adjustment and lubrication of your bike chapter take your bike to your authorized dealer WARNING If your brakes are not working correctly you may lose control and fall Carefully inspect the brake system before each ride Do not use the bike until any problem that may arise with the brake system has been resolved Check that both wheels are secured
10. Use a front and rear light when riding in low light Also you should wear light colored shiny and reflective clothing especially at night to make you more visible WARNING A cyclist without the proper lighting equipment may not have adequate visibility and others may not see him her either This could cause accidents with severe consequences for the cyclist Avoid these situations by installing a front and rear light in addition to wearing light colored easily visible clothing Avoid letting water enter any bearings Your bike s bearings allow the various parts of the bike to move smoothly Corrosion occurs when water comes into contact with metal therefore it should be avoided Avoid cleaning your bike with power washing systems like those used for cars Use caution when braking Always maintain a safe distance from vehicles and other objects Adjust the distance to your braking capacity If your bike has two brake levers squeeze them at the same time Excessive use of the front lever and braking with the front brake lever alone could cause the rear wheel to lose contact with the ground and make you lose control Many new brake models are very powerful and are able to stop the bike on wet or muddy terra in If you notice that your brakes are too strong for your needs take your bike to your authori zed dealer for adjustment or to change the braking system WARNING f you apply excessive force the rear wheel could lose
11. cause leaking problems If the tires are well fit to the rim the interior pressure of the tire is enough to maintain the seal You do not need a compressor to fill the tires A good pump will suffice Installing the valve Align the holes of the rim and the rim tape for the valve Align the valve head with the holes above and push the valve through the rim tape and rim Screw the tubeless valve stem lock nut with your hand There should be no space between the rim and the valve Check that the rim tape is properly in place Installing tubeless tires We recommend dampening the rim and tire with soap and water to facilitate installation Starting with the area opposite the valve insert one side of the tire inside the rim Repeat this action with the other side of the tire Inflating tubeless tires Inflate the tires until the pressure reaches 4atm Most tires have lines or markings just above the chafer When the tire is properly positioned these markings should be uniform around the rim Once the tire is properly fit onto the rim finish inflating it WARNING If tubeless tire pressure is low you could lose control and fall Do not use tires with under 2atm of pressure Removing tubeless tires The area of the rim where the tire rests is very thin Therefore you will need to rotate the tire to remove it from the rim Allow all of the air to be released from the tire Spin the tire while removing one of t
12. greater care and more frequent inspections Be careful It is preferable that you always ride accompanied Your companion will be able to help you immediately in the event you have any trouble or an accident Also you should never forget to take a puncture repair kit or a spare inner tube and tire levers with you on all of your rides You should also consider taking a multi tool specific to your bike and a first aid kit if you are planning to ride long distances 4 GENERAL RECOMMENDATIONS Keep your bike clean In order for your bike to work properly it must be kept clean Store your bike in an appropriate place When you are not using your bike keep it in an area where it is protected from the rain snow and sun Rain and snow can cause the metal to corrode Ultraviolet rays from the sun can disco lI ORBEA lor the paint or dry rot the bike s rubber or plastic components When storing the bike lift it off the ground and leave the tires at half their pressure Do not leave the bicycle near electric motors since the ozone emitted by the motors destroys rubber and paint Before using the bicycle again make sure it is in optimum condition Protect your bicycle from thieves Your new bicycle is very attractive to thieves You can insure your bike in several ways Register your bicycle in a local police file Purchase and use a lock A good lock is effective against knives and saws Follow the recom
13. not have channels replace them when the end of the rubber pad is only 3mm from the metal support Regulating the brake shoe vertically should be such that the edge of the rim is 1mm above the end of the shoe The shoe must come in contact with the rim exactly perpendicular to the braking surface as shown in the figure below brake block 1mm rim The shoe must be slightly inclined in the direction of the wheel s rotation Otherwise braking will be deficient and could cause bothersome noises when the brakes are applied J e a 2 direction of rotation brake block Once a month check the brake cables for twisting rust broken threads and frayed ends and check that the housing is not crimped cut or worn Replace any component that does not pass inspection In Cantilever brakes there should be a distance of 20mm between the link unit and the end of the brake cable housing support 20 mm more on flexible pipe KT Cm 9 XX UN p d N cable SUC AS clamp bolt e In V Brakes if the perpendicular distance to the braking surface can be regulated make sure that Distance A as shown in the diagram below is greater than or equal to 39MM Every 3 months tighten the bolts in the brake levers and shoes Brake lever mounting bolt 6 8Nm Every 3 months tighten the bolts in the Cantilever V Brake and Caliper brakes Brake
14. provided by the suspension supplier If you have not received said information you can download it from the supplier s website or contact us For optimum performance of your rear suspension system the maintenance and care for each one its parts is very important Frame Swing arm Bearings Mounting components Rear shock lI ORBEA For your system to work correctly it is very important that the different components are secu rely tightened and the rear shock is adjusted according to your weight way of riding and type of terrain on which you normally ride Keep the suspension components clean Dirt mud and other pollutants can cause wear or pre mature fatigue of the suspension To clean the suspension system use a cloth and soft bristle brush with soap and water Never use solvents or chemicals that could strip the lubrication from the bearings or rear shock Changing the characteristics of the suspension system will have an impact on the headset and braking system of your bicycle After making any changes ride in an area that is flat and free of traffic so that you can check and familiarize yourself with your bike s new performance Lubrication You should not lubricate the shock or pivot of the suspension system on your bike since this could damage the cartridge or bearings For the long life of your suspension system only clean it with soap and water or with water alone 10 CARI
15. shoe holder 8 10Nm Brake mounting bolt 8 LONm Cable fixing 6 8Nm Adjustment Adjusting brake lever reach It is possible to regulate the reach of some brake levers Find the reach adjustment screw for the lever To increase the reach turn the screw clockwise To reduce the reach turn the screw counterclockwise On some occasions it is necessary to readjust the distance between the shoes and the rim after adjusting lever reach brake 5 brake lever bolt Adjusting the distance between the shoes and the rim To increase the distance to the rim turn the reach adjustment screw clockwise Turn it counter clockwise to reduce the distance If you cannot adjust the shoes in this manner loosen the pinch bolt and tighten the cable again ORBEA as explained in the section for installing a brake cable but without removing it Centering V Brake Cantilever and Caliper brakes Turn the central screw in short intervals checking the centering often Adjusting the alignment of the brake shoes Loosen the brake shoe holder bolt Follow the instructions for inspecting the alignment and tightening the shoes After the brakes are adjusted fully depress the levers 10 times Make sure the cables do not come loose the shoes remain in the correct position with respect to the rim and that the tires do not come in contact with the shoes adjuster screw e 9 D M l
16. speed and adapt to the conditions You are less visible at night than during the day even if your lights are on Ride defensively In addition we recommend you change the light bulbs in your system every six months because there is no indicator to warn you if they are broken You will run the risk of being left without functioning lights when you most need them Avoid pulling or cutting cables of the lighting system if they are damaged the lights will stop working Installation If your bicycle does not have a set of lights and you would like to add them we recommend you talk to your authorized dealer If you want to change the light bulbs in your lighting system check the voltage and power of the original bulbs If you have any questions talk to your authorized dealer Installing a light bulb Find the screw for the cover behind the rear or front light Unscrew it using a Phillips screwdriver Take apart the light bulb so that you can unscrew the bulb itself Be careful not to break the light bulb when removing it Install the new light bulb in its place and follow the instructions in reverse ORBEA MAINTENANCE cD SCHEDULE r BEFORE EVERY USE WEEKLY MONTHLY EVERY 3 MONTHS ANNUALLY Check that the wheels are trued Check that the screws in the various Check the rims Inspect and lubricate brake levers Lubricate suspension forks suspension systems are tight Check
17. stress on your bike and components causing them to fail or to fatigue prematurely Failure can happen suddenly with no warning causing loss of control serious injury or death PARTS HARDWARE mechanic 4 27 4 REAR WHEEL PARTS Y0000008 4 HEAD TUBE PARTS Y0000008 ESPACIADOR 1200 130 Cod 16100028 GUIA CABLE FRONTAL Cod 16100122 3 ESPACIADOR DCHO PARA 130 MM 27 TORNILLO CABEZA ESTRECHA M3x8 PATA CARRERA 2 AGUJEROS IZDA 4 NEGRO Cod 15430056 5 TORNILLO AVELLANADO M4x8 NEGRO 33 PATILLA DE CAMBIO PARA 130 mm Cod 15430055 AMANT EBBER CORREA 9 FRAME amp FORK CAPS Y0000008 4 DROPOUT CAPS y0000008 NEM TAPON DESVIADOR SIN AGUJERO 06 Cod 16100023 TAPON PASO CABLE HIBRIDAS Cod 11069035 it TAPON PASO CABLE HIBRIDAS Cod 11069035 12 PEGATINA 8 Cod 16100124 12 PEGATINA 8 Cod 16100124 16 TAPON PLAST OBTURACION 5mm Cod 11389150 17 TAPON CON AGUJERO 22x8 Cod 116100125 AMANT econo ORBEA 0 PARTS HARDWARE 4 27 5 REAR WHEEL PARTS Y0000009 5 HEAD TUBE PARTS Y0000009 ESPACIADOR 1200 PARA 130 MM Cod 16100028 GUIA CABLE FRONTAL ELECTRONICO Cod 16100126 3 ESPACIADOR DCHO PARA 130 MM 27 TORNILLO CABEZA ESTRECHA M3x8 5 TORNILLO AVELLAN
18. the rim tape opening Using your fingers lift and stretch the rim tape so it is situated in the rim cavity Complete the tire installation procedure INSTALLING THE TIRE These instructions apply to standard wheel systems where the air inside the tire is retained by an inner tube Follow these instructions for repairing and replacing the inner tube or tire Removing the wheel Follow the instructions for opening the brake in the braking system section Follow the instructions on how to remove the wheel in the wheels chapter ORBEA Removing the tire from the wheel Never use sharp object or a screwdriver to remove the tire Use your hands or tire levers Completely deflate the inner tube Squeeze the sides of the tire around the entire rim Starting with the area opposite the valve start removing the tire from the rim Continue removing the tire around the rim until it is completely free Remove the tire and the inner tube Installing the tire If you are repairing a puncture repair the punctured area with a patch or replace the inner tube Follow the inspection procedure in the wheels section to check the rim and inner part of the wheel If you are replacing an inner tube or tire make sure the new tire is the same size as the pre vious one or ask your authorized dealer about compatible options You will be able to find the size on the side of the tire Slightly inflate the inner tube Positio
19. types of stems Traditional quill stem has a tube that fits inside the fork steerer tube using an adjustable wedge Ahead threadless stem attaches to the outside of the steerer tube Inspection If you have any doubts about the reliability of your handlebar take your bicycle to your authori sed dealer Once a month you must ensure that the stem is aligned with the front wheel Check the connection between the stem and the handlebar by moving it against the front wheel You should also inspect the safety of the handlebars and the bar ends by checking that the handle bars do not turn independently of the stem and that the bar ends to do not move independently of the handlebar Make sure no cables are stretched or crimped when rotating the handlebar Check that all bolts are tightened You should always heed the torque indicated by the piece If that information is not available it will vary based on the size of the Allen wrench required for the bold Nm Lb In Kg cm Allen wrench size mm Min Max Min Max Min Max 3 2 5 3 22 27 25 Sil 4 4 5 35 44 41 51 5 6l 8 6 11 15 97 112 153 ORBEA Adjustment The handlebar position and angle depend on the user and his her comfort efficiency and balan ce Your hands must be in a comfortable position in which the controls can be easily handled If your hands arms or shoulders are in an uncomfortable position you shou
20. 5 97 133 112 153 ORBEA If you have a quick release on the saddle clamp it works exactly the same as the quick release for your wheels Follow the instructions for securing it Never open the quick release while you are riding lockout lever nut N 45 quick release Adjustment Saddle height is very important for your comfort safety and pedaling efficiency The incline of the saddle affects your comfort Changing the saddle angle affects the distribution of weight between the handlebar and the saddle When properly adjusted the saddle is reasonably comfortable even when riding long distances WARNING A poorly adjusted saddle or unsuitable support of the pelvic area could affect the ner vous system and blood vessels with extended use of your bike Change the saddle if it causes pain or numbness Adjusting the saddle angle Loosen the saddle bolt so that it can move somewhat The adjustment of the saddle is very personal Start with the saddle parallel to the ground or slightly angled forward on full suspension bikes Tighten the saddle bolt as indicated in the inspection clamp bolt upper jaw grip Adjusting saddle height Loosen the quick release or saddle bolt Raise or lower the seatpost The average height of the saddle is calculated such that you can touch the ground on tiptoes of both feet at the same
21. ADO M4x10 NEGRO 33 PATILLA DE CAMBIO PARA 130 mm Cod 15430055 MEzevA 9 12 9 amp 7 wee 16 19 ER 8 16 SLS 5 HEAD TUBE Di CAP Y0000009 5 FRAME amp FORK CAPS Y0000009 TORNILLO AVELLANADO M4x10 NEGRO Cod 16100127 TAPON SHIMANO Di2 D6 NEGRO 13 Cod 16100127 10 TAPON CAMBIO Di2 06 Cod 11001145 12 PEGATINA 8 Cod 16100124 16 TAPON PLAST OBTURACION 5mm Cod 11389150 AMANT WBWMSERERUS ORBEA 9 5 DROPOUT CAPS Y0000009 TAPON CAMBIO Di2 6 Cod 11001145 12 PEGATINA 68 Cod 16100124 AMANT woens ORBEA PARTS HARDWARE nisc brake B REAR WHEEL PARTS Y0000010 6 FORK w DISC BRAKE PARTS Y0000010 Zeo SSS ae Se PATA CARRERA 2 AGUJEROS IZDA ADAPTADOR FRENO DISCO DELANTERO Cod 16100128 NEGRO Cod 15430056 TORNILLO AMARRE FRENO DISCO DEL M6x37 26 20 PATA CAMBIO REC CARRERA 2 AG 03 Cod 15430040 22 TORNILLO AVELLANADO M4x8 NEGRO 34 ARANDELA INOX M6 Cod 12321021 AMANT woens ORBEA B FRAME amp FORK CAPS Y0000010 B DROPOUT CAPS Y0000010 el DESVIADOR SIN AGUJERO 06 Cod 16100023 TAPON PASO CABLE HIBRIDAS Cod 11069035 it TAPON PASO CABLE HIBRIDAS Cod 11069035 12 PEGATINA 8 Cod 16100124 12 PEGATINA 8 Cod 16100124 16 TAPON PLAST OB
22. NG FOR YOUR FRAME AND FORK Orbea frames are constructed with a range of premium materials For safety and durability purposes take care of your bicycle and keep the following specifications in mind Inspection Before each use carefully inspect the entire frameset frame and fork for any signs of fatigue such as scratches cracks dents deformities or discoloring If any of the components shows signs of fatigue or is damaged replace it before using the bicycle Information about the frame In aluminum and steel frames the seatpost must be greased prior to inserting it in the frame A special carbon compound should be used for this in the carbon frame A thin layer of grease will insulate it and prevent corrosion The resistances for the various pressure adjusters or threads are extremely important If you tighten a piece excessively of if it is misaligned the piece or the frame may break In you apply too much torque you could break the piece or damage the thread You should always begin screwing with your hand and not a wrench The torque for the lower mount is 50 70Nm The torque for the cassette is 8 10 When cleaning the parts of the frame do not use solvents or strong chemicals Any dirt should be cleaned with a cloth and soap and water The use of industrial solvents could damage the frame s paint Stripping the paint from the frame requires special techniques and much care Some abrasives can strip part of the frame mate
23. TURACION 5mm Cod 11389150 17 TAPON CON AGUJERO 22x8 Cod 116100125 AMANT WBWEMSEREHRS ORBEA 19 23 4s 7 27 1 BB CABLE GUIDE Cod 16100120 8 FD HANGER PARTS Cod 16100121 GUIA CABLE PEDALIER CHAPILLA DESVIADOR 27 TORNILLO CABEZA ESTRECHA M3x8 23 TORNILLO GOTA DE SEBO M5x15 ALANT TECHNICAL SPECIFICATIONS ORBEA 33 25 9 KIT RD HANGER MECHANIC Cod 15430055 10 SEAT CLAMP PARTS Cod 11160786 AC TORNILLO AVELLANADO M4x8 NEGRO ABR SILLIN ORBEA 08 31 8 ALU NEGRO 33 PATILLA DE CAMBIO PARA 130 mm 24 ROSCA ABR SILLIN ORBEA 08 2 13 25 TORNILLO ABR SILLIN ORBEA M5x20 MANT ORBEA CABLE SYSTEM Disc Brake Gable Routing MEzevA ORBEA CABLE SY TEM Mechanic System Gable Routing N p MANT ORBEA 0 CABLE SYSTEM 12 System Gable Routing ALANT TECHNICAL SPECIFICATIONS OLT LIFE TIME WARRANTY ACTIVATE ORBEA WARRANTY WWW orbea com a R a a R HOW DO I AGTIVATE LIFETIME WARRANTY Orbea provides a lifetime warranty on all its frames Only a brand that knows the materials masters the technologies and has the skills can guarantee that your frame is totally invincible Only Orbea takes you a step beyond Orbea s lifetime warranty is activated using th
24. a in top condition 1 Keep your road bike clean Washing your bike with mild soap and water will keep you looking stylish and allow you to check the condi tion of the frame and components Dont s use high water pressure and avoid spraying water into bearings or frame tubes Citrus degreasers are biodegradea ble and do a great job of removing dirty grease from gears and chain 2 Keep your road bike lubed Once your bike is clean it s a good time to put fresh lube on the chain Use only enough to get inside the links and wipe off any excess because it will attract dirt Headset and pivot bearings should be inspected every few months for smoothness and to ensure that the seals are intact and lube is clean 3 Inspect your road bike before you ride Do a quick check before every ride to make sure your bike is in excellent condition It is very common to dis cover small issues at home that can become big pro blems on the trail CHAIN Is the chain dirty noisy or dry Clean and lube your chain before riding BRAKES Check your brakes to make sure they are working correctly Check for missing loose caliper and rotor bolts TIRES Look for damage to the sidewalls of your tires Check and adjust tire pressure WHEELS Spin the wheels and look for wobbles check for loose or broken spokes Check quick release levers to make sure they are functioning properly FRONT END Stand over the saddle pull on the brakes and rock the bike back and forth
25. ake your bike to an authorized dealer for inspection and repair WARNING Excessive vibration can cause you to lose control and fall If you feel excessive vibration immediately reduce your speed and take your bicycle to your authorized dealer Make sure your accessories are compatible and safe To personalize your bike various components can be changed and different accessories can be added Not all accessories are compatible or safe If you are not sure if a component is adequa te or safe talk to your authorized dealer CAUTION Inappropriate components or assemblies on your bicycle could exert unknown tension on your bike This stress could cause a failure that makes you lose control and fall Before adding or changing any element on your bicycle talk to your authorized dealer 2 BEFORE EACH RIDE CHECK YOUR BIKE Before each ride check your bike and its components using the following checklist This list provides some guidelines but is not to be considered a complete inspection Remember that if you detect any problems with your bike and you are not able to repair them you must take your bike to your authorized dealer Check that the wheels are trued Spin each wheel and check for brake pad and frame clearance If the wheel spin is not uniform take your bike to an authorized dealer Check tire pressure Inflate your tires to the pressure indicated on the side of the tire You should also take your own weight into consideration
26. bea com CONGRATULATIONS You have chosen a bicycle that WE have proudly manufactured We thank you for your trust in us We have been manufacturing bicycles for more than a century and all of our products are the result of our lengthy experience Your bicycle is the product of continuous research and infinite testing that have led to its manu facture with the best components and highest levels of quality The assembly and initial adjustment of your Orbea bicycle requires special tools and skills for that reason it should only be performed by your authorized dealer DEFINITIONS In this manual the word WARNING indicates potentially hazardous situations which if not avoi ded could result in serious injury or even death In this manual the word CAUTION indicates potentially hazardous situations or unsafe practi ces that could result in minor to moderate injury This manual covers the entire Orbea bicycle range which is made up of two types of bicycles Below is a diagram to help you identify the most important elements of your bike Understan ding them will help you to better comprehend this manual saddle stem handlebar brake lever gear shifter tyre seatpost head tube front brake fork rim seatstay spokes sprocket rear derailleur stay ORBEA CONTENTS 9 a MANUAL SPECIFICATIONS 22 22 0222402422 34 Never change the fork frame
27. bike for twisting rust broken threads and frayed ends and check that the housing is not crimped cut or worn Replace any component that does not pass inspection Adjustment Adjusting the reach of the brake levers Locate the reach adjustment screw between the lever and the handlebar near the lever pivot To increase the reach turn the screw clockwise To reduce the reach turn the screw counter clockwise Adjusting the gap between the pad and the disc Turn the pad adjuster bolt To increase the pad gap turn the adjuster clockwise To decrease the pad gap turn the adjuster counterclockwise Aligning the brake with the disc Loosen the caliper mount bolt Depress the lever as much as possible and gradually tighten the bolts as specified in the inspection section Removing brake pads Remove the wheel With your fingers or needle nose pliers pull the tab of the brake pad Removing the wheel Removing the wheel with disc brakes does not require you to take apart the braking system Carefully slide the disc out of the brake When you are going to replace the wheel carefully guide the disc between the brake pads If you press the edge of the disc against the pads they can crack or be damaged and need to be replaced Lubrication Lubricate the pivots every three months with synthetic lubricant as you would with the chain The brake pads do not need to be lubricated Installing the cable Follow the
28. ce the force transmitted to the chain since this could hinder the shift and wear out the chain and cassette You should never shift on uneven surfaces Internal shifter This system can shift when the chain is moving forward but it can also shift when stopped or moving backward Whenever you shift reduce the force transmitted to the chain to facilitate the shift Choose the gear ratio that offers you the most comfort when pedaling Prevent the handlebar from striking the frame In some bikes the front wheel can rotate to extreme angles and the handlebar can strike the frame Avoid this impact by adding pads to the end of the handlebar or to the frame itself Never change the fork frame or components A modification to any part of the bicycle including the frame fork or any other component could make your bicycle unsafe For example poor paintwork could reduce the rigidity of the frame Changing the fork of your bicycle could affect the bicycle s headset or create undesired tension Never install a suspension fork on a road bike If you want to change the fork of your bicycle talk to your authorized dealer about the different compatible options Any modification to the frame fork or components means that the bicycle no longer complies with our specifications and therefore would render the bicycle s warranty void CAUTION Never modify the frameset Never sand drill fill or disassemble any excess retaining devices or t
29. cleats should be posi tioned by the authorized dealer In most clipless pedals the force needed to insert and remove your foot can be regulated Getting into clipless pedals Fit the front of the cleat into the front of the pedal and push downwards with your foot It will click when it is in position Check that the connection is secure by rotating the pedal If your shoe comes out repeat the previous step To mount your bike push the pedal downwards while pushing forwards with the other foot while sitting on the saddle Once in motion insert your other foot into the pedal using the same technique Getting out of clipless pedals Twist your heel laterally with respect to the central line of the bike To stop put your foot on the ground 4 THE DRIVETRAIN PEDALS CHAINRING CHAIN AND CASSETTE The bicycle s drivetrain transmits power to the back wheel through Pedals Chainring and crank arms Chain Cassette This section will explain how to inspect adjust and lubricate the drivetrain For bikes with rear internal hub gears see the section on Internal hub gear system Inspection When the drivetrain is functioning properly shifting is easy and silent Once a month check that the cassette and chain are clean and well oiled All links in the chains should pivot well without squeaking Likewise check that no links are deformed Remove the rear wheel and spin the cassette If you hear a strange noise
30. contact with the ground or the front wheel could slip making you lose control and fall Brake with both sides at the same time and shift your weight to the back of the bike when braking Be careful when riding in wet conditions There is no brake regardless of design that is as efficient in wet conditions as in dry Though the brakes are trued lubricated and in good operating conditions in wet conditions the braking system requires greater force in the levers and braking distance Rain reduces both visibility and traction Ride at lower speeds around curves manhole covers and crosswalks in rainy or wet conditions Be especially careful when riding off the asphalt Ride in marked areas Avoid rocks branches and dips Never ride on an unpaved road or path with a road or urban bike Wear proper clothing and protection such as a helmet glasses and gloves When nearing a descent slow down and keep your weight back and low Use the rear brake more than the front Keep your bicycle in perfect conditions Bicycles are not indestructible like any machine each part of the bike has a service life limited to tension and fatigue Fatigue refers to minor tensions that when repeated a finite number of cycles can compromise the integrity of the material The service life varies according to its design material use and maintenance Lighter frames generally have a longer service life than heavier frames and premium bikes need
31. d not be used until that issue has been repaired the piece replaced or the bike taken to your authorized dealer What is torque Torque is a measure of the force needed to rotate an object about an axis like a screw or bolt These measurements are made using a dynamometric wrench The indicated specifications for torque are guidelines to help you determine the correct tightness of the different pieces and their threads It is important to respect the torque specifications so the threads are not over exerted Applying greater torque than recommended to a piece does not provide greater fastening but could cause the piece to be damaged or rendered unusable 1 HANDLEBAR BAR ENDS AND STEMS The handlebar is the part of your bike that you hold with your hands when riding Controlling the bicycle is the responsibility of the rider Moreover the handlebar and saddle define the cyclist s position on the bike You must make sure that the position is as ergonomic as possible The han dlebar is connected to the rest of the assembly through the stem This section will explain how to inspect adjust and lubricate handlebars stems and bar ends Never allow the bar ends to come into contact with any object that could cause you to lose con trol of the bicycle The bar ends have been designed exclusively to support your hands during ascents Make sure the bar ends are facing forward at an angle greater than 15_ with respect to the ground There are two
32. dealer 11 ACCESSORIES Introduction To improve the features of your bike it can be equipped with different types of accessories such as dynamos lighting systems to improve visibility luggage carriers or bells All accessories must be properly maintained for optimum performance Inspection Once a month inspect the various accessory nuts and bolts and their respective mounting systems The torque for the fender bolts is 3 5 4 5Nm and the connection between the fender and frame should be 6 7Nm lI ORBEA Lighting systems The lighting system has been designed to increase security in low visibility conditions such as night time or fog These lighting systems can be powered by dynamos or batteries If a dynamo is used it must be properly installed and adjusted so that it is in the On position thanks to the spinning motion of the wheel to provide the necessary power to the lighting system at a minimum speed of 6km h WARNING When the bike is stopped the dynamo cannot generate energy for the light bulbs thus reducing visibility and causing you to not be seen by other vehicles In this case use batte ries or avoid stopping in poorly lit areas Once the dynamo is connected make sure the light shines and is properly aimed so that you can have optimum light and luminosity The lighting system must be kept clean Remember that your field of view is smaller at night therefore you should reduce your
33. e regis tration number you will find on all frames from the 2009 range onwards When you have activated it at your dealer or at www orbea com your bike will auto matically receive its lifetime warranty The registration number is a unique non transferable code that you will find on the underside of your bike s downtube Activate your frame s warranty using this number at your dealer s or at www orbea com WHAT ARE THE ADVANTAGES Lifetime guarantee of your frame against breakage Two year guarantee on all components Identification of your bicycle and all its characteristics to our Technical Assistance Service so that wecan pro vide our best response to any problems Access to special offers events and prize drawings ORBEA WARRANTY The ongoing efforts we make at Orbea to design high end bicycles enable us to provide customerswith the following warranty 1 We back each frame and rigid fork in our bicycles with a lifetime warranty against materials and manu facturing defects Frames with travel longer than 170 mm are covered by a 2 year warranty We warrant each frame and fork in our bikes against paint or var nish defects and corrosion for 3 years This warranty covers the original purchaser only and is non transfe rable For the lifetime warranty to be valid customers must fill in the online warranty form within one mon th of purchase and proof of purchase in the form of cash register receipt or sales ticket is requir
34. e shifting lever or on the derailleur itself to achieve the optimum adjustment If the chain falls from the outside cog tighten the outer limit screw one quarter of a turn If the chain cannot shift to the outside cog from the outside cog loosen the outer limit screw H one quarter of a turn If the chain falls from the inside cog towards the spokes tighten the inner limit screw L one quarter of a turn If the chain cannot shift to the inside cog loosen the inner limit screw one quarter of a turn If the cassette cannot be aligned as indicated take the bicycle to your authorized dealer Optimizing use of the rear derailleur If your bike is equipped with a double or triple chainring kit you will be able to ride anywhere easily saving your strength and maintaining a uniform pedal stroke regardless of the terrain or your speed However to avoid any mechanical issues chain skipping noise when pedaling etc follow these recommendations Select the correct gear by shifting just before the start of an ascent or the obstacle you are maneuvering When you are about to shift gears keep pedaling normally without excessive force and use the shifting levers until the chain is correctly positioned on the desired cog and chainring Avoid shifting when straining even if the synchronized systems allow for it in a tough situation Strictly avoid extreme combinations such as the inner chainring with the two oute
35. e up of Brake lever Brake cables and housing Disc brake pads Disc brakes can become very hot after use Be very careful when inspecting them Like with other parts of your bike avoid inserting your fingers in the disc WARNING Disc brakes can become very hot and even burn your skin Moreover the corners can be sharp and cut you Avoid touching the disc and brakes when they are hot or rotating Inspection Before every use squeeze the brake levers firmly 10 times The lever should never come in contact with the handlebar Check that there is no oil grease or other type of dirt on the disc The disc is an essential part of the braking system therefore it must be kept clean Remove the brake pads from the cali pers when you are going to deep clean Do not use cleansers degreasers or solvents to clean ORBEA the disc Only use isopropyl alcohol Once a month make sure that the disc brakes are not worn If the brake pads have a thickness less than 1mm they should be changed You must also check that the brake pads are correctly positioned at a distance between 0 25 and 0 75mm from the disc when the brakes are not applied Turn the wheel When the levers are not depressed the brake pads should touch the discs as little as possible The torque for disc brake bolts is Caliper mount bolt 11 5 12 5Nm Caliper bridge bolt 11 5 12 5Nm Disc screws 5 6Nm Pinch bolt 6 8Nm Once a month check the brake cables of your
36. ebar while holding the wheel between your legs minimum insertion SE stem binder k A handlebar cone binder bolt bolt Note If your bicycle is equipped with an ahead threadless stem there are practically no op tions for regulating handlebar height Therefore we ask that you consult your dealer and do not perform any adjustments yourself 2 SADDLE AND SEATPOST The saddle is where you sit on the bike when riding and it is supported by a seatpost The seatpost is connected to the frame with a clamp or quick release Proper adjustment of each component is important for your safety comfort and pedaling efficiency This section will talk about how to inspect adjust and lubricate your saddle seatpost and clamp seatpost minimum insertion mark seatpost bolt top tube seat tube Inspection Once a month you need to inspect the quick release of the seatpost or seat tube clamp Make sure that the saddle is secured to the frame assembly and has no horizontal vertical or rotational movement with respect the axis of the seat tube If you notice any of these types of movements properly readjust all connections You should always heed the torque indicated by the piece If that information is not available it will vary based on the size of the Allen wrench required for the bold Nm Lb In Kg cm Allen wrench size mm Min Max Min Max Min Max 3 25 3 22 27 25 31 4 4 5 35 44 41 51 5 6 8 53 71 61 82 6 11 1
37. ed 2 Warranty claims are subject to the decision made by our technical staff about the nature of the defect after thorough inspection of the faulty part 3 All the parts assembled in our bicycles are protec ted against assembly or manufacturing defects for 2 years and repairs qualifying under this warranty will be performed by authorized dealers in each country 4 This warranty does not cover parts that naturally wear over time such as tires brake pads handlebar grips cranksets bearings etc 5 This warranty does not cover damages or defects caused by negligence improper use assembly ofparts or accessories that are not original or defective repair or maintenance work of the bicycle nonoriginal ac cessories being fitted to it or unsuitable maintenance operations or handling ORBEA 0 6 This warranty includes only replacement or repair coverage of the parts under it and in no case shall it cover personal damages directly or indirectly caused by the failure of said parts during use 7 All claims must be reported to an authorized dealer In case there is no such a dealer near the buyer s lo cation please contact Orbea so that we can decide how to solve the problem 8 In case of crashes the Orbea warranty shall be con sidered null and void ORBEA 0 AMANT CORBA 8 ADDITIONAL INFORMATION Orbea participates actively on facebook and Twitter with our fantastic global community of riders Loo kin
38. emove them from the hub Replacing the rear wheel Place the chain on the hub not on the cog and slide the hub towards the teeth Push the wheel to the proper position in the rear fork lift the chain to position it on the cog pulling on the wheel to obtain good tension While you are holding the wheel in the frame and maintaining the chain tension follow the instructions to remove the wheel backwards including the gradual adjustment of the bolts If necessary you will have to re tense the chain Re install the brake arm and tighten the brake arm bolt Follow the inspection steps in the wheels section of this chapter to complete installation Spin the wheel to see if it spins freely and is centered Verify that the brake is functioning properly Lubrication Coaster brakes do not need additional lubrication Follow the recommendations in the Wheels section for the lubrication of the hub bearings 7 WHEELS Introduction Bicycle wheels allow the bike to travel smoothly therefore their integrity is essential The rela tionship between the wheels and the braking system is extremely important This section will explain how to inspect adjust and lubricate the wheels of your bike Inspection The best type of maintenance you can perform on a wheel is preventive Be aware of any pro blems that could arise and correct them before they occur Before each use check that the quick release is in the Closed position
39. ey are loose or you hear a strange noise in the bearings they need to be checked by your dealer Clean the chainrings and inspect them for any damage If any tooth is bent or damaged the chainring must be replaced by your authorized dealer Check the chain for wear every three months Every complete link of a chain measures one inch 25 4mm If twelve links measure more than 30 8cm the chain must be replaced With a properly maintained road bicycle the chain generally lasts between 1600 and 2400 km The service life for mountain bikes is slightly less Special tools and know how are required to chan ge the chain Therefore you should take your bike to your authorized dealer Adjustment Adjusting the drivetrain cassette chain chainring and pedals must be performed by an autho rized dealer since it requires specific tools and special skills Adjusting the chain on a single speed bicycle Gradually loosen the nuts of the wheel hub In single speed bikes or bicycles with internal hub shifters chain tension has to be adjusted so that halfway between the wheel hub and bottom bracket there is 1cm of slack in the chain Tighten the nuts until the wheel is uniformly secured Lubrication and cleaning Once a month clean and lubricate the cassette and the chain You should always keep a cloth behind the chain so that oil does not drip on the rest of the bicycle Once the chain is lubrica ted clean any excess off t
40. g to find spots to ride or plan a vacation Someo ne will have the answers FACEBOOK www facebook com OrbeaBicycles TWITTER https twitter com Orbea TECH VIDEOS Visit our Orbea Channel on YouTube for a variety of helpful setup and tech videos http www youtube com user OrbeaBicycles INSTAGRAM instagram com orbeabicycles ORBEA GONTENT View and download photos videos and documents http content orbea com YOUR ORBEA DEALER Our dealers are experts and should be able to assist you with setting up and maintaining your Orbea bicy cle A complete listing of Orbea dealers and distribu tors can be located on our website http www orbea com int en dealers country INT AFTER SALES SERVICE Our service technicians are trained to handle any questions you might have about your Orbea bicycle mailto Orbea Orbea com INSTRUGTIONS AND MAINTENANCE MANUAL ORBEA MANUAL SPECIFICATIONS This manual has been prepared to help you enjoy your new bike to the fullest Please read it carefully This manual provides guidelines for the periodic checks you need to carry out so that you can properly maintain your bike If you have any questions or concerns after reading this manual do not hesitate to talk to your regular Orbea dealer There you will find personnel you can trust for the most complicated tasks and the best advice available Any deviation from the instructions contained i
41. ge noises the hub will need to be adjusted Repeat this process with the rear wheel Every month check the wear of your rims In some adult bicycles there are indicators for wear on the braking surface If the rim is so worn that you cannot see the wear indicators the rim change should be performed by your authorized dealer Before installing the rim make sure the rim tape is installed so that the spoke nipples or ends do not puncture the inner tube WARNING Make sure the rim tape covers all spoke ends and nipples If any are left uncovered and puncture the inner tube the wheel will lose pressure suddenly making you lose control and fall Adjustment Adjusting the front hub This procedure requires specific materials and know how Therefore it should only be perfor med by an authorized dealer Adjusting the quick release mechanism To properly and safely adjust the quick release mechanism carefully read and follow the instruc tions below CLOSED NV S OPEN position 1 M T Turn the lever of the quick release to the Open position and insert the wheel in the blades of the bike and make sure the axle is securely positioned Now move the lever to 45 and tighten the quick release bolt clockwise with your hand until you cannot turn it anymore Move the lever to the tightening position Once closed it should be in the Closed position as shown in the upper left figure Do not tighten the quick release as
42. he beads of the tire from the rim Once it has come out completely remove the other bead starting at the valve Installing an inner tube and tire A standard tire can be used with an inner tube Make sure the rim tape is covering all spoke ends and nipples Install the inner tube and tire as you normally would Converting to a tubeless tire Remove the tire and inner tube Make sure the rim tape is covering all spoke openings Follow the instructions for installing a valve Follow the instructions for installing a tubeless tire and inflate it Removing the rim tape If the rim tape is going to be used again be careful not to damage it Follow the instructions on how to uninstall a tubeless tire and the valve stem Insert a screwdriver through the valve opening of the rim tape between the rim tape and the rim Lift the rim tape with the screwdriver and insert a tire lever under the rim tape Using the tire lever lift and turn the rim tape upwards and outwards from the rim Installing rim tape There are two types of rim tape one for symmetrical rims and one for asymmetrical rims Con firm that you are installing the correct type of rim tape for your rim If your rim is asymmetrical make sure it is well aligned Check that the rim tape is in good condition without scratches holes or deformities Align the opening of the rim tape with the hole in the rim for the valve Insert the valve stem through
43. he chain Do not use gasoline to clean the cassette It is highly flammable and leaves a thin film of grease after it evaporates Clean the cassette with a degreasing fluid and brush Once a year lubricate the pedal bearings the clipless pedal mechanism and the part of the pedal that screws into the crank arms Some bearings are sealed and do not require lubrica tion Lubricating the bearings requires specific tools and special know how and should only be performed by an authorized dealer Note The left and right pedals have a mark stamped on the corner indicating the side to which they pertain Greasing the thread of the pedals Remove the pedals spin the right pedal counterclockwise and the left pedal clockwise Apply a thin layer of lubricant Install the pedals on the corresponding side Tighten the pedals until they are securely connected to the crank arms pedal 5 GEAR SHIFTER TRADITIONAL DRIVETRAIN Attachment of the rear derailleur to the frame 6 8Nm Attachment of the front derailleur to the frame 5 6Nm Attachment of the shifting levers to the handlebar 6 8Nm This gear shifting system changes the chainring and cassette by derailing the chain removing it from one cog or chainring to another Inspection The following terms will be used in this section Upshifting shifting to a gear that is harder to pedal a larger chainring or a smaller cog Dow
44. he like An improper modification could cause you to lose control and fall 5 CHILDREN Proper supervision of children and all who are learning to ride a bike practicing safety on the road and abiding traffic regulations are critical to their training Explain everything presented in this first chapter to your child before he or she rides the bike for the first time Make the following basic rule very clear to your child CHILDREN MUST ALWAYS WEAR A HELMET WHEN RIDING A BICYCLE OR TRICYCLE Training wheels Some Orbea models are equipped with training wheels This way children can learn to ride with these wheels and develop proper control of the bike Until the child s skill on the bike has been fully developed the child should always be supervised by an adult Installing training wheels Check that the tires of the bike are correctly inflated Position the bicycle on a flat surface ORBEA Loosen the nuts of the rear hub and follow the specifications in chapter 2 Put the bicycle upright and position the training wheels about 6mm from the ground Make sure the height is the same on both sides of the bicycle Retighten the nuts as specified in the chapter Inspection adjustment and lubrication of your bicycle including how to adjust the tension of the chain Inspect the anchoring of the wheel as specified in that chapter Readjust the wheels as the child becomes more skilled As the child becomes more co
45. heck the lighting 37 Hydraulic disc brakes erem nnns 50 Check the handlebar doeet net ecdesia doi 37 Mechanical disc eene trennen 51 Check 37 Drum brakes 52 3 Riding safely ie ite e ei er Ee 37 Coaster brakes a 53 Wear a helmet 37 7 Wheels s uc o secte e MAMMA 53 Be aware of local traffic laws for 37 Removing and installing wheels with gear shifting mechanisms cc 55 Do not perform stunts or other unsafe activities with your bike 37 Schrader and Presta 55 Ride 37 Tu ubelesswhe lS ert c ertet rel eto 55 Watch the 37 ennt temple enin tee bene 56 Watch the cars you going to 38 8 Reflectors oroia a 57 Be careful when riding in low light conditions sss 38 9 Suspension systems cceccessesscecsesecsesacsesassesassesaesesacsesassessesacscsecsesacsesacsetacsesassesaes 57 Avoid letting water enter any bearings 38 Suspension systems Forks esses 57 Use caution when 38 Suspension systems rear 5 5 5 57
46. if it were a bolt the attachment will not be tight enough to keep the wheel in position SG WARNING quick release that is not properly adjusted could cause the wheel to loosen or fall out unexpectedly and cause you to lose control or possibly fall Be sure that the quick release is correctly adjusted and closed before using the bicycle If the lever can be easily moved to the Open position less than 50 Newton that means that the fastening force is insufficient In this case re tighten the quick release bolt clockwise and turn the lever to the Closed position If the force needed to turn the lever is excessive More than 200 Newton repeat the operation above but loosening the bolt counterclockwise Repeat these operations as many times as needed until you find the optimum fastening force The quick release should be oriented in such a way that it does not interfere with other bike accessories If the quick release mechanism fails take your bike to your authorized dealer Checking the quick release mechanism adjustment Lift your bike and strike the upper part of the wheel The wheel should not drop out loosen or move from side to side Make sure the quick release lever cannot rotate in parallel with the tire If you need more than 200 N force to close the quick release it is too tight and you must readjust it If you need less than 53 N to close the quick release it is too weak and you must readjust it Ad
47. installation instructions explained for Cantilever V Brake and Caliper brakes DRUM BRAKES Introduction The braking mechanism is found within the rear hub but unlike coaster brakes it is applied by hand The lever is connected to the brake through a cable and the system has the following components Brake lever Brake cables and housing Rear hub Inspection You should check that the bolts of the braking system are well tightened and that the brake cables have no rust broken threads or frayed ends You must also check that the housing is not crimped cut or worn Replace any pieces that do not pass your inspection Adjustment Reducing lever reach Loosen the adjustment barrel and turn the screw To increase the reach turn it clockwise Turn it counterclockwise to reduce the distance After adjusting the reach tighten the barrel ORBEA Removing the rear wheel First disconnect the rear derailleur and brake cables To disconnect the brake cable be careful not to touch the rear hub since it may be hot even 30 minutes after use To disconnect the gear cable shift to the outside cog Pull the cable housing and turn the mounting nut until the washers align with the groove Once this is completed you can remove the cable To uninstall the hub from the frame turn the hub bolts gradually in small movements so that the adjustment of the bearing axis is not affected To install the rear wheel follow the inst
48. justing with bolts Install the wheel into the blades of the frame or fork and make sure the axle is securely inside the slots ORBEA Insert the clamp nut Gradually turn the nuts on either side of the axle in opposite directions The following torques should be applied Front wheel 20 28 Nm Rear wheel 27 34 Nm Check that the nuts are properly adjusted as specified in the section below If the nuts are not correctly positioned repeat the adjustment procedure or take your bike to your authorized dealer Checking the clamp nuts are properly adjusted Lift your bike and strike the upper part of the wheel The wheel should not drop out loosen or move from side to side Adjusting tire pressure If you cannot maintain proper tire pressure it is most likely punctured or has a leak Repairing a puncture is explained in the tire inspection section If you do not have the proper tools to com plete the repair take your bicycle to your authorized dealer REMOVING AND INSTALLING WHEELS WITH GEAR SHIFTING MECHANISMS Some parts of this chapter refer to parts that have already been explained such as wheels and braking systems Note to remove the rear wheel with coaster braking systems follow the instructions specified in the brake section Removing the wheel Position the chain on the outermost cog Open the brakes as indicated in the braking section Open the quick release of the wheel or loosen the hub nut
49. ld adjust the handle bar or look for components that better meet your needs Check with your authorized dealer Some handlebars have marks that indicate where they can be cut If your handlebar does not have these marks do not shorten it If you want to shorten it but are unsure please check with your authorized dealer Adjusting the handlebar angle Loosen the bolt in the stem clamp enough to be able to turn it Position the handlebar at the desired angle and check that the stem is centered Tighten it as specified in the inspection Adjusting the stem inclination angle Loosen the stem angle adjuster bolt until you can turn it Position the stem at the desired angle Adjust the bolt as specified in the inspection Changing handlebar height with a traditional quill stem Al requerirse ciertos conocimientos y herramientas especiales es conveniente que sea hecho Since this process requires certain skills and special tools we recommend it be performed by your dealer Loosen the stem binder bolt with two turns counterclockwise Lightly tap the bolt with a wooden or plastic mallet to unlock the stem cone Adjust the stem to the desired height Re tighten the bolt and verify that the handlebar is perpendicular to the front wheel Do not over tighten the bolt it could break and seriously compromise your safety Check that the handlebar binder bolt is sufficiently tightened by applying lateral pressure to the handl
50. mendations for use Never leave your bike unlocked If you have quick release mechanisms on the wheels lock the wheels to the frame If there is a quick release mechanism on the saddle you should take the saddle with you when the bicycle is locked However you should avoid allowing water to enter the frame through the seatpost Protect your bicycle from possible bumps Always park your bike in areas where it is out of the way of moving vehicles and ensure that it is in a stable position so that it does not fall Do not lean the bike against the cassette since it can be damaged or become dirty Keep the bike from falling since this could damage the handle bars or the saddle etc Also the improper use of a luggage carrier could damage the bike Use the proper technique when shifting gears Some Orbea bikes are equipped with two gear shifting systems One is a derailleur drivetrain in which the chain moves from one toothed cog to another In the others the shifting system is situated in the rear internal hub Read the instructions below depending on the gear shift system you have Traditional shifter The left shifter controls the front derailleur and the right shifter controls the rear derailleur Choose the gear ratio that offers you the most comfort when pedaling You can only shift when the chain is moving forwards Never try to shift gears when stopped or moving the chain backwards Whenever you are going to shift redu
51. mfortable on the bike gradually increase the distance of the training wheels from the ground until the child no longer needs them INSPECTION ADJUSTMENT AND LUBRICATION OF YOUR BICYCLE This chapter addresses the inspection intervals to follow for each component of your bicycle as well as the instructions for adjustment and lubrication If during inspection you find that any of the pieces does not satisfy the requirements for operation the bicycle should not be used until that issue has been repaired the piece replaced or the bike taken to your authorized dealer The inspection interval for each component is based on a regimen of normal use If you use your bicycle more than normal under adverse weather conditions like rain or snow or on unpa ved roads maintenance should be performed more often than indicated in this chapter Bicycles are not indestructible like any machine the different parts of the bike have a service life limited to wear and tear tension and fatigue Fatigue refers to small magnitude forces that due to repetition in a large number of cycles could compromise the integrity of the material The service life of the different parts varies according to its design material use and mainte nance Some possible signs of bicycle fatigue are dents cracks scratches deformities and discoloring WARNING f during inspection you find that any of the pieces does not satisfy the requirements for operation the bicycle shoul
52. n Positioning and adjusting the front derailleur To correctly position the front derailleur The cage plates must be perfectly parallel to the chainrings Vertically the position should be such that with the front derailleur and the chain on the middle chainring the gap between the bottom of the outer cage plate of the front derailleur and the top of the outer chainring teeth is between 1 to 3mm as shown in the figure below seat tube derailleur H 142mm i large chainring p CCS 1 7 For proper regulation of the front derailleur motion it should have two screws regulating the inner and outer limits of the motion that can be positioned in different places depending on the front derailleur model The adjustment should be performed as follows Place the chain rear derailleur and front derailleur in the inside chainring inside cog position Turn the inner limit screw L so that when pedaling the chain moves as close as possible to the inner part of the inner cage of the front derailleur without rubbing at any point see figure inner part of derailleur Aan Place the chain rear derailleur and front derailleur in the outside chainring outside cog posi tion Turn the outer limit screw H so that when pedaling the chain moves as close as possible to the inner part of the outer cage of the front derailleur without rubbing at any point see figure outer part of de
53. n the inner tube in the tire Insert the valve through the opening in the rim Starting at the valve insert the tire into the rim Push the tire until it is completely installed with the inner tube inside the tire and the tire inside the rim Be careful not to pinch the inner tube in the tire or rim Inflate the tire halfway and check that the tire is properly fit into the rim Inflate the tire to the pressure indicated on the side Installing the wheel Follow the instructions on how to install the wheel in the wheels chapter Follow the instructions for closing the brake in the braking system section 8 REFLECTORS Introduction The reflectors of your bicycle reflect light shone on them In conditions of low visibility if a vehicle comes close to you with the lights on the reflectors will help you be seen Reflectors are an important part of the safety system Therefore you must not remove them Inspection Every three months make sure that all nuts and bolts holding the front rear and pedal reflec tors are correctly positioned and attached Check that the front and rear reflectors are properly positioned and perpendicular to the ground You must also check that all reflective surfaces are clean and in good condition The rear reflector must be at least 75 mm below the saddle 9 SUSPENSION SYSTEMS Suspension systems Forks Suspension forks allow the front wheel to move in way that absorbs the shock from irregulari
54. n this manual will be the responsibility of the user of the bicycle All individuals must at least read the chapter on Guidelines for the safe use of your bicycle in this manual Parents and guardians of minors must explain the chapter Guidelines for the safe use of your bicycle to children who are unable to read and comprehend it It is very important that you read the chapter Guidelines for the safe use of your bicycle before riding your new bike even if you have been riding for years This manual covers all Orbea models There are numerous Orbea models with different specifi cations Therefore this Manual will contain some information that does not apply to your bicycle model Some illustrations may vary with respect to the models in the current catalog Note We may refer you to the supplier manual for suspension forks and several other parts If you have not received the manual corresponding to those parts you can download it from the supplier s website If you are not able to do so please contact us or your authorized dealer If you have any questions after reading this manual or the Orbea website please talk with your authorized Orbea dealer If you have a problem that your authorized dealer is unable to resolve please contact us by email phone or online Poligono I Goitondo 48269 MALLABIA Bizkaia Apdo 1 20600 EIBAR Gipuzkoa tel 34 943 17 19 50 Fax 34 943 17 43 97 Email orbea orbea com www or
55. noodle from the noodle holder With one hand squeeze the brake shoes against rim and with the other pull the noodle backwards from the holder and lift the noodle Once disconnected the brake will open when you release the shoes To close the brake follow these instructions in reverse Lubrication Every 3 months lubricate the brake lever pivots with synthetic lubricant as you would for the chain When you are going install a brake cable you should grease it with a thin layer of synthetic lubricant HYDRAULIC DISC BRAKES Introduction Instead of a shoe exerting pressure on the rim of wheel a pad acts on a disc located in the front or rear hub The disc fits onto the hub with bolts on the left side The braking system is made up of Braking levers Fluid reservoir Hydraulic hose Disc brake pad Brake fluid from disc brakes is highly corrosive Avoid contact with the skin or bicycle as it could corrode the paint Disc brakes can become very hot after use Be very careful when inspecting them Like with other parts of your bike avoid inserting your fingers in the disc WARNING Disc brakes can even burn your skin Moreover the corners can be sharp and cut you Avoid touching the disc and brakes when they are hot or rotating You should not depress the brake levers when the disc is not inside the caliper If the lever is de pressed when the disc has been removed the distance between the pads is almost null due to
56. nshifting shifting to a gear that is easier to pedal a smaller chainring or a larger cog Proper adjustment of the gear shifting system will make it silent If there is temporary noise every time you shift the shifter may need adjustment If you cannot adjust it or the noise increa ses take the bike to your authorized dealer Once a month check that the cables are not twisted rusted have any broken wires or frayed lI ORBEA ends You should also check the housing for loose cables bent ends cuts and signs of wear If you think there is a problem with the cables do not ride your bike Change the cable or take your bike to your authorized dealer Once a month check the function of the left shifting lever or front derailleur Every time you change the chainring the front derailleur must be in a position that it does not rub against the chain Furthermore the chain must not fall off the outside or inside chainring at any time Once a month check the function of the right shifting lever or rear derailleur Every time you shift the cog should be situated so that the chain can run smoothly without jumping Further more the chain should not fall off the outside or inside cog at any time Adjustment Shifter adjustment must be performed with the bike firmly secured to a work bench or with someone holding the rear wheel in the air so that the gear shifting system and drivetrain can work in a stationary positio
57. ntrol of your bicycle and fall When you are nearing a stop you should be able to easily remove your feet from the pedals Always remove one foot from the pedal before completely stopping the bike Before using your bicycle for the first time if you have clipless pedals you should familiarize yourself with them and practice getting into and out of the pedals in a stationary position Once ORBEA this movement is natural practice in a flat area without traffic While pedaling watch the road If you are looking at the pedals you may not see the obstacles ahead Do not use clipless pedals with street shoes since your feet will not have a good support base on the pedal Remove at least one foot from the pedal before stopping the bicycle completely Inspection Before every use you should clean both the cleats and the pedals since any dirt could interfere with the proper functioning of the mechanism Every three months check that the pedal reflectors are clean and correctly positioned Make sure the pedals are properly secured to the crank arms To check that the pedal bearings are well adjusted move the pedals up and down and left to right If you feel that anything is loose or too stiff take the bicycle to your dealer so they can be adjusted lubricated or replaced The pedal to crank arm torque should be 40 43Nm Adjustment Improper installation of the cleats could cause physical injury therefore
58. or 39 a 34 5 god A s 34 y 4 P CONTENTS s 35 i Handlebar rere e ir es cena 40 GUIDE TO USING YOUR BICYCLE 36 2 Saddle and 41 1 Before your first ride 36 MEINEK 42 2 Before each ride check your 36 4 The drivetrain Pedals Chainring Chain and Cassette 43 Check that the wheels are 36 5 Gear 22 2 2 2 menester street erret erret renes 44 Check tire pressure nen 36 Traditional drivettaiil 2 n e err ere ebbe m a bcc ee 44 Check your 5 36 Internal gear hub drivetrain 47 Check that both wheels are secured eese 37 6 Fork and headset ssssssseeeeneneemeeeneemreer erret retener serere trenes 47 Check the handlebar and stem for signs of fatigue or increased tension 37 Braking SyStem nennen nnne nnne ren 48 Check the adjustment of the 37 Rit braking Voi c cette 48 C
59. or if the cassette stops as soon as you let go it may need to be repaired or replaced take the bike to your authorized dealer Once a month if your bike has a chainguard check that it is securely attached and aligned Try to move the chainguard from one side to the other and tap it Lift the rear wheel and turn the crank arms to hear if the chain or the chainring is rubbing against the chainguard Realign the chainguard and adjust the screws so it is secure Inspect your pedals every three months Check that the pedal reflectors are clean and correctly positioned Make sure the pedals are properly secured to the crank arms To check that the pedal bearings are well adjusted move the pedals up and down and left to right If you feel that anything is loose or too stiff take the bicycle to your dealer so they can be adjusted lubricated or replaced Every three months inspect the crankset and check that the bolts are secured The following torques should be applied Single chainring binder bolt 40 50Nm Crank arm binder bolt 15Nm Chainring bolts 8 10 Chainring adjustment check Shift the chain to the largest chainring Spin the chainrings until the crank arms are parallel to the seatpost ORBEA Put one hand on the crank arm and one on the seatpost try to move the crank arm towards and against the seatpost If it is loose it needs to be checked by your dealer If when turning the chainrings you notice that th
60. or that the nut is well tightened For more information about tightening the wheel read the corresponding section or ask your authorized dealer Check that the wheels are trued and centered by spinning them If the rim spin is not uniform talk to your authorized dealer Make sure the wheels are inflated and the tire pressure is correct Inflate the tires using a hand pump Never inflate your tires at a gas station Check the tires for wear or any other type of damage If a tire has any cuts or openings that allow you to see the inner tube change it before riding Check that the wheels are clean A dirty or greasy wheel could impede proper brake function Clean the rims with a clean cloth or ORBEA wash them with soap and water Rinse and allow to air dry Every week make sure there are no loose damaged or broken spokes If a wheel is not in good condition the efficacy of the brakes and the rigidity of the set will be severely reduced WARNING An improperly adjusted hub could cause you to lose control and fall Carefully ins pect the hub system before each ride and do not use the bike until any problem that may arise during the inspection has been resolved Once a month check that the front and rear hubs are well adjusted Lift the front wheel and try to move the rim from left to right Watch and feel for any play in the rim Spin the wheel and listen for any strange sounds in the movement If the hub appears to be loose or makes stran
61. r tube A normal tire can fit onto the rim without using an inner tube without a problem However you will have to install a tube since the tire is not sufficiently sealed to maintain the pressure This section explains the requirements of this system and includes instructions for assembly WARNING A normal tire is not able to maintain air pressure without an inner tube If an inner tube is not used you could lose control and fall Always use an inner tube with standard tires Repairing punctures in tubeless tires A well installed tubeless tire can lose up to 0 25atm per day If the loss is greater than that look for a leak Dirt sand mud or possible grooves could weaken the seal between the rim and the tire and cause leaks Check that the valve is firmly in position Check for punctures and the sealing surface Tire with rim Valve with rim If the tire has a puncture hole smaller than 3mm it can be repaired from inside the tire with an appropriate patch If the opening of the tire is greater than 3mm the entire tire must be ORBEA replaced A tubeless tire must be completely sealed to the rim Before inflating a tubeless tire you must make sure that the connection between the rim and tire is correct This connection must be even more secure than that of the conventional tire If you are using tire levers be careful not to damage the rim or the tire itself If any of the surfaces is scratched installing the tire could
62. r use rims designed for disc brakes with these systems The rims must have a flat surface on which the brake shoes can act Inspection Before using your bike squeeze the brake levers firmly The lever should never come in contact with the handlebar If the lever touches the handlebar the reach should be regulated as explai ned below If you have a hydraulic systemic it must be purged This action must be performed by your authorized dealer since it requires specific materials and know how Likewise if you have a hydraulic system check that there are no crimps or leaks in the hose Replace any hydraulic part that does not pass inspection This replacement requires specific tools and know how Therefore it should be done by an authorized dealer When the brakes are not being applied the shoes should be 1 2mm from the rim The brake shoes must be aligned with the rim surface If your brakes are too loose tight or misaligned with the rim adjust them prior to using the bicycle The angular alignment of the brake shoe must be considered to prevent the brakes from squea king Used brake shoes and some new V Brake types may not require this alignment Once a month check the status of the brake shoes The brake shoes have small channels on the friction surface If any of these channels is less than 2mm deep or less than 1mm in V Brakes ORBEA the brake shoes must be replaced If the original brake shoes did
63. railleur To confirm try pedaling with all of the chainring cog combinations possible If the chain falls off onto the crank arm in any of the combinations turn the outer limit screw H one quarter turn clockwise If the chain falls off onto the bottom bracket in any of the combinations turn the inner limit screw L one quarter turn clockwise If the front derailleur makes noise or the chain does not shift from one chainring to another smoothly in the intermediate positions turn the barrel adjustment on the derailleur lever to achieve the optimum adjustment Adjusting the rear derailleur Like the front derailleur the rear derailleur has inner and outer screws to limit the motion of the rear derailleur that can be positioned in two different places depending on the derailleur model The process is very similar to that used to regulate the front derailleur and is explained below ORBEA Position the upper jockey wheel of the rear derailleur in line with the smallest cog using the outer limit screw H Position the jockey wheel of rear derailleur in line with the largest cog using the inner limit screw L screw screw wheel top idler wheelin ner limit screw To confirm try pedaling with all of the chainring cog combinations possible If the rear derailleur makes noise or the chain does not shift from one cog to another smoothly in the intermediate positions turn the barrel adjustment located on th
64. resist the weight of a person up to 100 kg and 10 kg of cargo Mountain bikes For use on an asphalt gravel surfaces or rough trails and any type of terrain in which the tires could momentarily lose contact with the ground Road bikes For use on asphalt surfaces where the tires are always in contact with the ground Recreation bikes For use on asphalt and gravel surfaces or rough terrain where the tires are always in contact with the ground 1 BEFORE YOUR FIRST RIDE Your authorized dealer should provide you a bicycle that fits you correctly In a standing position on your bike make sure there is adequate space between your groin and the top tube For MTB bikes this distance should be between 50 75mm For all other bikes this distance should be 25mm Practice at slow speeds Before riding at high speeds or under adverse conditions you need to learn the functions and characteristics of all of your bike s mechanisms by riding on flat roads without traffic That way you can get to know all of the features of your bicycle If you want any operational features other than those that come standard to your bicycle for example a brake force modulator consult your authorized dealer Avoid excessive vibrations or imbalances on the front wheel Heavier cyclists with large bikes sometimes experience excessive vibration harmonic oscilla tion or frame vibration at certain speeds If you experience this reduce your speed and t
65. rial and thus weaken it It is advisable that you contact your dealer The frame should not be exposed to extreme temperatures 65 C since they could damage the binding adhesive of the various components If the frame is modified in any way the warranty is voided and the use of the frame could be hazardous Changing the fork could affect your bicycle s turning capacity or create excessive tensions Suspension forks can generate effects of fatigue on your bicycle You must not add suspension to a road bike or modify the length of a fork If you are going to replace the fork of your bicycle talk to your dealer to make sure that the fork is compatible with the frame WARNING Never modify the frame assembly in any way Sanding drilling filling holes uninsta lling excess devices or any other operation on the bicycle in addition to improper modifications of the frame fork or any other component could cause you to lose control of the bicycle and fall Carbon frames It is essential that carbon frames have a chainstay guard in place in the event the chain falls inward Check that the frame chain protectors are always in good condition If they are dama ged go to your dealer so they can be replaced immediately Do not leave these frames exposed to the sun since they degenerate faster than aluminum or steel frames Frame repair Most damage to the frame has to be repaired at the Orbea plant The frame can be returned through an authorized
66. rmost cogs or outer chainring with the two innermost cogs These situations as shown in the figure below lead to a diagonal chain line that jeopardizes the performance of the drivetrain and durability of your components premature wear CHAINRING CRANKSET 7 speed freewheel bottom bracket chain crossover to avoid Replacing the gear wire Position the chain on the inner chainring and outer cog Loosen the pinch bolt holding the wire and pull it through the shifting lever If you cannot access the wire due to the type of shifter talk to your dealer Inspect the housing Change it if it is worn or rusted Grease the new wire and insert it through the lever and all guides and housing Follow the instructions for adjusting the cassette Cut the wire so that it does not overhang more than 5cm from the pinch bolt Attach a metal end cap to the wire to prevent the end from fraying Lubrication Every month lubricate all of the pivot points of both the front and rear derailleurs as well as on the jockey wheels Any wires that have been replaced must be lightly greased in those areas where it passes through housing or rubs against anything ORBEA INTERNAL GEAR HUB DRIVETRAIN Some bicycles are equipped with a type of shifter inside the rear hub Nexus 7 8 speed The internal gear hub drivetrain is made up of the following specific components Shifters
67. ructions above inversely including the slow tightening of the bolts Once this is completed check the tension of the derailleur cable and inspect the wheel Lubrication You must lubricate the pivots of the brake lever every three months Every time a new brake cable is installed it must be lubricated COASTER BRAKES Introduction Instead of being applied with your hands coaster brakes are applied using your feet and peda ling backwards The chain transmits the movement of the pedals to the rear wheel hub where the braking mechanism is located This braking system consists of Rear hub Chain and chainring crank arm set Inspection Once a month you must make sure the sprocket bolt is tight and the driver system is well fit to the sprocket Once a month or whenever you replace a wheel make sure to check the tension of the wheel Without proper tension the chain can fall off causing the brake to malfunction Chain ad justment is explained in previous chapters Removing the rear wheel To remove the brake arm loosen and remove the brake arm bolt To uninstall the hub loosen the hub bolts gradually in small increments so that the adjustment of the bearing axis is not affected Slightly loosen the nut on one side of the hub by turning it one quarter of a turn Slightly loosen the nut on the other side of the hub by turning it one quarter of a turn Continue loosening the nuts carefully until you are able to r
68. the handlebars or any other part of the frame they could get stuck in the spokes and cause the handlebars to jerk suddenly making you lose con trol of your bicycle Do not ride under the effects of alcohol or medicines that cause drowsiness Bicycles require good coordination of movements and your must always be alert to your surroundings Do not carry anyone on your bicycle Standard bikes are not designed to hold the additional weight of a second rider Moreover the extra weight makes the bicycle much harder to turn and stop Ride defensively To pedestrians drivers and other cyclists you are not as visible as a car You must always beware of dangerous situations and be prepared to stop Watch the road Be prepared to avoid potholes sewer grates or shoulders since they could cause your wheels to skid When maneuvering around an obstacle try to do so at a 90 angle and if you are unsure lI ORBEA of the conditions get off your bike Watch the cars you are going to pass If a car suddenly crosses your path or someone suddenly opens the door of a parked car you are going to pass you could have a serious accident Install a bell on your bike to alert others of your presence Be careful when riding in low light conditions Your bike is equipped with a complete range of reflectors Keep them clean and properly positio ned Though reflectors help you to be seen they do not provide emit light
69. the length of the old cable for installing the new cable Install the new cable Attach the cable fixing nut Attach the shifter casing Attach a metal end cap to the wire to prevent the end from fraying Follow the instructions to adjust the rear drivetrain Lubrication The rear drivetrain must be lubricated once a year This process requires specific tools and special know how It should only be performed by an authorized dealer The cable must be lubricated whenever it is replaced 6 FORK AND HEADSET The headset is the set of bearings that allows the fork stem and handlebar of the bicycle to rotate This section will explain how to inspect lubricate and adjust the fork and headset If your bike is equipped with a suspension fork read the chapter on suspension forks If your bi cycle has an aluminum or carbon fiber fork read the chapter on caring for your fork and frame Inspection Once a month inspect your bike s headset and check that it is not too loose or tight If it is do not use the bicycle Take it to your authorized dealer Checking headset play Stand over the horizontal tube of the bike with both feet on the ground Squeeze the front brake while moving the bicycle forward and back If your bicycle does not have a front brake turn the front wheel so that it is perpendicular the force applied Watch listen and feel if the headset is loose Checking the tightness of the headset adjustment
70. the self adjuster Therefore you will not be able to reassemble the disc If this were to happen consult the disc brake manual or go to your authorized dealer ORBEA Inspection Before using your bike squeeze the brake levers firmly The lever should never come in contact with the handlebar If the lever touches the handlebar the system should be purged This action must be performed by your authorized dealer since it requires specific materials and know how Check that there is no oil grease or other type of dirt on the disc The disc is an essential part of the braking system therefore it must be kept clean Remove the brake pads from the cali pers when you are going to deep clean Do not use cleansers degreasers or solvents to clean the disc Only use isopropyl alcohol Once a month make sure that the disc brakes are not worn If the brake pads have a thickness less than 1mm they should be changed You must also check that the brake pads are correctly positioned at a distance between 0 25 and 0 75mm from the disc when the brakes are not applied Turn the wheel When the levers are not depressed the brake pads should touch the discs as little as possible The torque for disc brake bolts is Caliper mount bolts 11 5 12 5Nm Caliper bridge bolt 11 5 12 5Nm Disc screws 5 6Nm Handlebar Master Cylinder Clamp Screw 3 4Nm Check there are no crimps or leaks in the hose Replace any hydraulic part that does not pass inspec
71. ties in your path and reduce the vibrations you feel Suspension forks must be regularly lubricated so that they can work smoothly and have a long service life The section below is complementary to the information provided by the fork supplier If you have not received said information you can download it from the supplier s website or contact us Inspection Before every use make sure the suspension fork is working correctly Never use the bicycle if there is not enough space between the fork and the wheel Adjustment The suspension fork preload setting can be modified as can the damper and coil spring speed Changing the characteristics of the suspension fork will have an impact on the headset and braking system of your bicycle After making any changes ride in an area that is flat and free of traffic so that you can check and familiarize yourself with your bike s new performance Lubrication Follow the lubrication and maintenance instructions in the suspension fork manual WARNING An improper adjustment of the suspension fork could cause you to lose control and fall Make sure the suspension fork bolts are properly adjusted and that the distance between the tire and fork is adequate Suspension systems rear suspension Rear suspension allows for a vertical movement of the rear wheel to absorb the shock from irregularities in your path and reduce the vibrations you feel The section below is complementary to the information
72. time Always ensure that the seat post is inserted within the seat tube above the minimun insertion levelRe tighten the quick release or saddle bolt WARNING A seatpost that is too high could damage the bicycle and cause you to lose control and fall Make sure the minimum insertion mark of the seatpost is inside the seat tube Lubrication The seatpost should be lubricated annually To do so Loosen the quick release or saddle bolt to remove the seatpost from the frame Clean the seatpost and remove the old grease if necessary Apply a new layer of lubricant Insert the seatpost in the frame Adjust the seatpost height align the saddle with the frame and tighten the quick release or the saddle bolt 3 PEDALS Pedals are the part of the bicycle where you put your feet Your control and safety on the bike depend on the security of the connection between the pedal and your foot For recreational use in flat areas a pair of soft soled shoes is sufficient For more intense use the pedal system should help keep your feet on the pedals Orbea uses different types of pedals Clipless pedals that snap into a cleat in the sole of the cyclist s specialized shoe Pedals without any type of attachment system If your bicycle is equipped with pedals that do not satisfy your needs talk to your dealer about this issue WARNING While riding your bike your shoes should be in contact with the pedals otherwise you could lose co
73. tion This replacement requires specific tools and know how Therefore it should be done by an authorized dealer Adjustment Adjusting brake lever reach Locate the reach adjustment screw between the lever and the handlebar near the lever pivot To increase the reach turn the screw clockwise To reduce the reach turn the screw counter clockwise Aligning the brake with the disc Loosen the caliper mount bolt Depress the lever as much as possible and gradually tighten the bolts as specified in the inspection section Removing brake pads Remove the wheel With your fingers or needle nose pliers pull the tab of the brake pad Removing the wheel Removing the wheel with disc brakes does not require you to take apart the braking system Carefully slide the disc out of the brake When you are going to replace the wheel carefully guide the disc between the brake pads If you press the edge of the disc against the pads they can crack or be damaged and need to be replaced Lubrication Lubricate the pivots every three months with synthetic lubricant as you would with the chain The brake pads do not need to be lubricated MECHANICAL DISC BRAKES Introduction Instead of a shoe exerting pressure on the rim of wheel a pad acts on a disc located in the front or rear hub The disc fits onto the hub with bolts on the left side The brake is activated using a cable that extends out of the lever The braking system is mad
74. tire pressure Lubricate the suspension fork Check the adjustment of the bea Inspect the cassette and chainrings Lubricate quick releases rings Check your brakes Check the spokes Inspect the adjustment of all acces Inspect the crank arms and pedals Lubricate the seatpost sories Check that both wheels are secure Clean the bicycle Check the chain tension Lubricate the valve stem Check the handlebar and stem Check the lighting system and Check the braking system Lubricate the pedal threads and reflectors bearings Check the suspension setting Check the tire for cuts and rips Check the internal shifter Lubricate the wheel bearings Check the lighting system Inspect and lubricate the cassette Lubricate the fork crown bearings and derailleur Check the saddle Inspect derailleur function Check gear and brake cables Check the chainguard and fender Check the saddle and seatpost Check the handlebar and stem We recommend taking your bike to your dealer for annual revision If you have any questions about how to perform any of these checks see the manual or talk to your dealer This maintenance sche dule is based on normal use If you use your bicycle in the rain or snow or if you ride on paths more frequent maintenance is required If any piece is damaged inspect it and repair it immediately or talk to your dealer ORBEA ORBEA RECOMMENDATIONS Never forget that taking care of nature is everybody s responsibility If you consider yourself a na
75. ture lover do not go off paths or trails or ride through prairies or meadows Always respect all living beings that cross your path be they people or animals Always grant them the right of way The best show of your good manners and sense of civic responsibility is to ensure that the only evidence of your ride through nature be the wonderful memories you have created If we all practice our favorite sport in perfect harmony with others and with nature we will be able to do so for many many years to come ADDITIONAL QUALITY GUARANTEE Orbea bicycles comply with the following safety standards EN 14766 Mountain bicycles EN 14781 Road racing bibycles EN 14761 Utility bicycles AENOR 5 AENOR D 62 Empresa Gesti n Registrada Ambiental Since 1995 has been awarded Orbea has satisfied the ISO 14001 ISO 9001 and IQNET quality assurance Environmental Standard since March certification 2004 www orbea com
76. ust be positioned at the proper height for your use and height Moreover you must also check that the seatpost and seat are correctly positioned and tightened 3 RIDING SAFELY Wear a helmet You must ALWAYS WEAR A HELMET and when riding on public roadways you must use the SIGNALING SYSTEMS provided with your bike An unprotected head is very fragile even in the event of a minor bump but wearing a helmet that complies with EC safety regulations or other recognized legislation could reduce that risk Eye protection and proper clothing are also recommended Be aware of local traffic laws for bicycles Most states have specific laws for cyclists Cycling clubs or the Department of Transportation or its equivalent in your area should be able to provide you information in that regard Some of the most important regulations are Use the appropriate hand signals When riding with other cyclists form a single file line Ride on the correct side of the road never against traffic Expect the unexpected and ride defensively Cyclists are difficult to see and many drivers are unaccustomed to recognizing the rights of cyclists Do not perform stunts or other unsafe activities with your bike Many cycling accidents can be avoided by using common sense Some examples Do not ride no hands the slightest imperfection in the road could cause a vibration or su dden turn of the front wheel Do not ride with objects hanging from
77. you are unsure about the adjustment of your brakes or if you suspect there is a problem do not use the bicycle Take it to your authorized dealer It is difficult to adjust the braking system if you do not have the necessary knowledge experien ce or materials We highly recommend that you have your authorized dealer adjust your brakes Not all brakes are compatible with all levers Only use levers that are compatible with your brakes such as those that originally came with your bike WARNING Never use the bicycle if the braking system is not working correctly or if you suspect there could be some problem either with the brakes cables or hydraulic system Poor brake function could cause you to lose control and fall If your bicycle is not functioning properly readjust it and take it to your authorized dealer RIM BRAKING SYSTEMS Introduction This system is made up of different brake families such as Cantilever V Brake and Caliper In these systems the levers are connected to the brake through cables or hydraulic systems When squeezing the levers the brake shoes act on the rim and slow the wheels which reduces the speed of the bicycle These systems are made up of the following components Rim Braking levers Fluid reservoir Brake cable and housing Hydraulic hose Brake shoes Brake fluid from the hydraulic system is highly corrosive Avoid contact with the skin or bicycle as it could corrode the paint Neve

Orbea Avant User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents