LinkBone 1-to-15 Switch user manual v0.9
Contents
1. PortN on Port O on Copyright 2014 LinkBone All nights reserved Figure 19 User configuration page in multi switching mode At the top of page there is navigation bar with the following pages e Switch switch configuration page e Network Ethernet settings configuration e Help Basic information about device operation The user Switch configuration page shows the port connection schematic To change the switch mode of the device select button with Switch mode label In single tap on the port status box mode to change the connection state The On label means that the connection is enabled The disconnected port is indicated by Off label In the multi mode select port state by using the checkbox and then click Apply changes key to confirm changes Detailed information about switching modes can be found in chapter 3 Device description To refresh the information about the device state select Refresh Status button The Network settings page figure 20 allows changing port mode Static or DHCP IP address subnet mask and default gateway The Ethernet port settings are described in Chapter 4 4 Ethernet settings ln DHCP mode change of IP address subnet mask and default gateway is not possible To accept changes select the Apply changes button After the update of network settings a message EJ LinkBone Switch User manual 1 to 15 Dual 1 to 15 type Link EERE will be displayed to use the newly2. Infrared remote control menu figure 11 contains the following items e IR access enabled disabled Enables or disables the infrared receiver When the receiver is turned on the switch state changes after successful decode of received RC5 code When the infrared receiver is off the device does not respond to the received RC5 codes e Assign RC5 code assigns the RC5 remote control code to current switch port state After assigned RC5 code is received the device will change its switch port state to programmed configuration e Delete RC5 code remove RC5 code with assigned switch port state from device memory After receiving the removed RC5 code the device will not alter its state e Return Return to the main menu The Infrared RC5 codes are being received using an RC Remote Control sensor on the front panel To modify the switch port status press previously assigned button on the remote control pointing at RC sensor figure 12 During receive of the infrared signals the status diode is red blinking r LinkBone Switch User manual 1 to 15 Dual 1 to 15 type System Display www LinkBone com Bone CI amm CIM Po L Figure 12 LinkBone Switch infrared remote control To assign a button from the remote control to the current configuration of port switches select Assign RC5 code option from menu In the next step press the remote control button to be programmed pointing at the RC sensor A
3. Link EEE LinkBone Switch Type 1 to 15 Dual 1 to 15 User manual Version 0 9 Copyright 2014 LinkBone All rights reserved Link EAE Table of Contents Me AO Ts ACO ee ee Ad 3 2 Inspection Ofthe SU UME a A OE OKE GOA dia ee eee eme De 5 3 DOVE Ce CO R o AA RA ene ae dues 6 3 1 OR O OPO A AOLO AE AEO 7 3 2 RE 7 3 3 MUM en SETUD e A E RAE R E EEN EEE EEN N OE ES 9 3 4 19 Rack system mounting procedure sise 10 SNS DEDO y e E EE EAE A AA 11 4 1 ASS Cl COUN OE A E EE E O Ge 11 4 2 Skee SECU ES E E AWARE E EA R E A Cn 13 4 3 infrared Remote Control Settings a a AEG GK locka kc 14 4 4 RSS a eee 16 4 5 DSZOZSBIUNOS OKO a oo OE WA 18 5 Eth fnet remote control porwana obescunauencavedduetanncindeetatvnncsdh dolaasssbwarsivdeoaddertteoraateaedeant 19 5 1 RS a A A E O S E E AA NA GAGA 19 5 2 FONCIER EEE AEGEE ORO at Go de ae 21 6 Access through RS 232 interface cscscsscssssccssosssccnsssssccsceusssscecusssssccsuseessuessseccusssssccussesseousesss 22 7 Text commands accepted by LinkBone Switch 1 to 15 Dual 1 to 15 type eseeeeeaaaaa aa aana 23 S DOVE CAR ee cE EEEE AO an De ne eee 24 J PEOGNE TECYCINE wawa a ea a te de 24 TE SOO CU CAS a a ae O 25 11 Appendix A Electromagnetic Compatibility ss 26 2 LinkBone Switch User manual 1 to 15 Dual 1 to 15 type Link EERE 1 Safety instructions The user should get familiar with safety requirements and operating instructions before t
4. Tapping Back button returns to previous menu canceling changes Figure 16 Ethernet interface edit screen LinkBone Switch User manual 1 to 15 Dual 1 to 15 type rza Link EERE 4 5 RS 232 settings Figure 17 Settings menu for the serial port RS 232 The RS 232 serial port settings menu figure 17 contains the following items e Baud Specifies the RS 232 port baud rate e Parameter specifying the length of the transmitted data words and parity bit The following configurations are available o 8 bits no parity 8 bit data word length no parity bit is transmitted o 8 bits odd parity 8 bit data word length odd parity bit is transmitted o 8 bits even parity 8 bit data word length even parity bit is transmitted e Stop bits specifies the number of stop bits between data words e This parameter defines the hardware control flow mode of RS 232 interface The following configurations are possible o HW flow disabled data is transmitted without control flow mechanism o HW flow RTS CTS data is transmitted using RTS CTS control flow according to the RS 232 standard e Accept accept the changes and update device settings e Cancel cancel the changes It is recommended to use the shielded M F all line RS 232 extension cables with up to 10 meter length for the connection with remote PC a LinkBone Switch User manual 1 to 15 Dual 1 to 15 type Bone 5 Ethernet remote control port The Link
5. Specifications Due to internal construction of signal ports there are two LinkBone Switch types 1 to 15 each port contains only one line for routing electrical signals Dual 1 to 15 each port has two symmetrical lines for routing electrical signals with numbers 1 and 2 e g for stereo audio or differential signals User configuration P Figure 1 LinkBone Switch 1 to 15 internal port connection diagram The device operates in two port switching modes single only one out of A to O ports can be connected to common port P at the same time In this configuration the device operates as a classic analog multiplexer demultiplexer To protect connected instruments from short circuit during switching all ports are disconnected before change of switch state multi there is no limit of ports connected to node P Meaning that more than one port can be connected to port P at the same time 6 LinkBone Switch User manual 1 to 15 Dual 1 to 15 type Link EERE NOTE because several ports can be shorted together during operation of switch proper protection circuits techniques are needed to avoid damage of connected equipment The port connection configuration can be done via touch screen located on the front panel or remotely via Ethernet RS 232 or infrared remote control The access via Ethernet interface is possible by following services HTTP server with user configuration page described in chapter 5 1 H
6. 61000 6 3 2008 A1 2012 poz 1 2 w Tablicy 1 Metody bada wykonanych wed ug procedur akredytowanych PN EN 61000 4 2 2011 PN EN 61000 4 3 2007 A1 2008 A2 2011 PN EN 61000 4 4 2013 PN EN 61000 4 5 2010 Metody bada wykonanych wed ug procedur nie obj tych akredytacj PN EN 61000 4 6 2009 PN EN 61000 4 11 2007 PN EN 55016 2 1 2009 PN EN 55016 2 3 punkt 7 4 PN EN 61000 3 2 2007 A1 2010 A2 2010 Data przyj cia obiektu do bada 07 04 2014 r Data wykonania bada 18 04 2014 27 05 2014 Wyniki bada Badana matryca prze czaj ca sygna y analogowe cyfrowe LinkBone Switch typu Dual Matrix S N A0142237019 z zasilaczem sieciowym PSC12R 120 S N P31501298A1 po zmianach konstrukcyjnych wykonanych w trakcie bada spe nia wymagania EMC okre lone w zakresie bada podanym powy ej Zmiany wprowadzone przez producenta w konstrukcji badanego urz dzenia mia y na celu obni enie emisji zaburze _przewodzonych i z Autoryzowa mgr in Donat Zeme ko 30 05 2014 r PAE pepas BADAWCZEGO WZQR ne mgr in Donat Zeme ko Niniejsze sprawozdanie z bada mo e by rozpowszechniane lub kopiowane tylko w ca o ci LinkBone Switch User manual 1 to 15 Dual 1 to 15 type
7. please remove the bottom battery cover Replace the batteries according to the drawing under the battery cover Please pay attention to the battery LinkBone Switch User manual 1 to 15 Dual 1 to 15 type EE Link EERE polarities and type Insert the battery cover The manufacturer is not liable for damage to the remote control because of badly inserted batteries The device LinkBone Switch fulfills the requirements of European Union directives for conducted and radiated emissions as specified in the appendix of this manual Connecting external high amplitude or high frequency signal sources to LinkBone Switch ports may increase the emissions level of the device to the value which does not comply with EU directives Therefore the user is obligated to check if conducted and radiated emission levels were not exceeded after connecting external signal sources and receivers to the LinkBone Switch ports If emission requirements are not met the user should tune the signal sources to reach an acceptable level of the EM emission If guarantee seals are broken or removed the manufacturer is not responsible for secure and proper operation of the device All repair or servicing activities should be performed only by authorized service centre Care should be taken to avoid mechanical damage of the unit during transport Do not faulty or damaged device In order to ensure safe and fault free operation of the device it is recommended to do the inspection of th
8. two options e Brightness settings related with screen brightness figure 10 including the following elements o Slider for adjusting the brightness of the backlight display by pressing the or keys o Screen off control specifying after what time the screen will be switched off This option can have the following values never the screen backlight will be never switch off 10sec switch off the screen after 10 seconds 30sec switch off the screen after 30 seconds 1 min switch off the screen after 1 minute 2 min switch off the screen after 2 minutes a 5 min switch off the screen after 5 minutes 10 min switch off the screen after 10 minutes Figure 10 Brightness settings e Calibrate starts touch screen calibration procedure figure 11 After selecting this item the user is asked to tap on the calibration points marked with symbol The incorrect or inaccurate calibration of the screen may cause erroneous responses from the touch screen If an error occurs during calibration procedure e g by touching wrong point location the process can be repeated by selecting Calibrate option or by holding down the reset button on the front panel for 5 seconds LinkBone Switch User manual 1 to 15 Dual 1 to 15 type 3 Link EERE Figure 10 Calibration of the touch screen e Return to return to the main menu 4 3 Infrared Remote Control settings Figure 11 Infrared Remote control settings
9. 348 4221 BP D BADANIA tel sekretariat 71 372 9934 fax 71 348 2183 e mail sekretariat iase wroc pl AB 1384 Laboratorium Badawcze i Wzorcujace SPRAWOZDANIE SKR CONE Z BADA Nr 34 DL II1 2014 Przedmiot bada a a Matryca prze czaj ca sygna y analogowe cyfrowe LinkBone Switch typu Dual Matrix w wersji z 15 parami z cz we BNC i jedn par z cz wy BNC S N A0142237019 produkcji Z U H KAMSERWIS Marcin Ostopinko z zasilaczem sieciowym PSC12R 120 S N P31501298A1 produkcji PHIHONG Zleceniodawca Zak ad Us ugowo Handlowy KAMSERWIS Zlecenie bada nr 483 600 606 Marcin Ostopinko er 98 400 Wierusz w ul Kasztanowa 4 zdnia 07 04 2014 r Rodzaj bada Laboratoryjne badania kompatybilno ci elektromagnetycznej EMC Podstawa Zakres bada Badania wykonano na podstawie normy PN EN 61326 1 2013 Wyposa enie elektryczne do pomiar w sterowania i u ytku w laboratoriach Wymagania dotycz ce kompatybilno ci elektromagnetycznej EMC Cz 1 Wymagania og lne z odst pstwem dotycz cym metody badania emisji zaburze promieniowanych Badania odporno ci wykonano wed ug wymaga przewidzianych dla urz dze przeznaczonych do pracy w podstawowym rodowisku elektromagnetycznym Emisj zaburze promieniowanych badano na stanowisku w komorze FAR metod wg normy PN EN 55016 2 3 2010 punkt 7 4 Poziom dopuszczalny emisji zaburze promieniowanych przyj to wed ug normy og lnej PN EN
10. Bone Switch Ethernet offers the following remote access services HTTP server with user configuration page Telnet server accepting text commands described in Chapter 7 Text commands accepted by LinkBone Switch 1 to 15 Dual 1 to 15 type For proper operation of network services a configuration of Ethernet settings is required The configuration is described in chapter 4 4 Ethernet settings 5 1 HTTP server To access HTTP server please type in the address bar the configured IP address of the LinkBone Switch Based on device switch mode appropriate user configuration page should be displayed Figure 18 shows the webpage in single switch mode operation Figure 19 shows the page in multi switch mode I 192 168 1 5 Bone Switch status Switch mode Signle Refres status Reset all ports PortA Porte NS Port C Port D Port E Port F Port G Port P Port H Port I Port J Port K Port DNS Port DNS Port N Port O Copyright 2014 LirkSone All rights reserved Figure 18 User configuration page in single switching mode LinkBone Switch User manual 1 to 15 Dual 1 to 15 type 19 o Link EERE om 192 168 1 5 NETWORK Switch status Switch mode Multi Refres status Apply changes Reset all ports Port A on PortB Con E Potc DER Cor PotD Con EJ PortE Con DER Port P PortH on E
11. Bone Switch accepts text commands described in Chapter 7 Text commands accepted by LinkBone Switch 1 to 15 Dual 1 to 15 type Done Unknown command Type help for list of commands IL ACE Figure 21 RS 232 remote terminal access a LinkBone Switch User manual 1 to 15 Dual 1 to 15 type Link EERE 7 Text commands accepted by LinkBone Switch 1 to 15 Dual 1 to 15 type List of text commands accepted by LinkBone Switch 1 to 15 and Dual 1 to 15 types e help prints the list of available commands e info prints information about the device e mode lt mode gt sets the operation mode of the device e off lt ports gt changes the port state to Off there is no connection to port e on lt ports gt changes the port state to On port is connected to common port P e reset resets the state of all ports to Off all ports are disconnected e status prints information about status of the switch e ping checks if connection to the device is active by replying Pong e quit closes current session this command is only available for a Telnet clients Remarks e All commands are case sensitive e lt mode gt parameter can have two values o single only one of A to O ports can be connected to port P In this mode switch operates as a Classic analog multiplexer o multi more than one A to O port can be connected to port P In this mode user should keep in mind that ports in On state are internal
12. Bone Switch containing the following elements 8 AtoP bidirectional signal ports The specification of the ports can be found in chapter 10 Specifications a The BNC port version has the following pin connections Center nut port signal line Shield ground connection b The XLR port version has the following pin connections pin numbers are included on the XLR connector 1 ground connection 2 positive signal line 3 negative signal line 9 fuse socket for fuse replacement type please refer to chapter 10 Specifications 10 12V DC input power connector refer to chapter 10 Specifications for more information 8 9 10 Ja ee eG ee ee ee oe ee en NN TD TD 1 8668 Figure 3 Rear panel of the LinkBone Switch FI LinkBone Switch User manual 1 to 15 Dual 1 to 15 type Link EERE 3 3 Instrument setup Before powering the LinkBone Switch please place it on a flat stable and dry surface Stick the four self adhesive rubber feet on the bottom surface of the device housing Ensure that there is no access to the unit by children Insert the power adapter DC plug into 12VDC socket on the rear panel of the device Set the power switch on front panel into O position Please make sure that used AC power outlet fulfills the power requirements described in chapter 10 Specifications Plug the power adapter into your AC power outlet Figure 4 shows the power connection diagram AC wall outlet 12VDC power
13. Switch User manual 1 to 15 Dual 1 to 15 type ES Link EERE 3 Device description LinkBone 1 to 15 Switch is an analog multiplexer switch designed for switching digital and analog signals between common port P and set of fifteen ports marked with letters from A to O Gold cladding on internal switching contacts ensures very low resistance and failure rate In order to maximize the contact life time all switching contacts are cut off from external atmosphere to prevent from corrosion and oxidation The state of internal switches does not change after interruption or disconnection of power supply which allows limiting power consumption in standby mode to minimum The architecture of LinkBone instruments provides high reliability of switching for wide range of signal voltage levels and current values The block diagram illustrating the connection of input output ports is shown in figure 1 Each port with marking from A to O includes individual signal switch allowing shorting or disconnecting to common node P Each switch state is set by user configuration independently All lines can route electrical signals bidirectionally between ports Meaning that port P can be connected to signal source and ports from A to O to receivers or vice versa To prevent the accumulation of electrostatic charge that can damage connected devices each port is connected to ground via a 5 1 MQ resistor For detailed port parameters and characteristics please refer to chapter 10
14. TTP server Telnet server accepting text commands described in chapter 7 Text commands accepted by LinkBone Switch 1 to 15 Dual 1 to 15 type The switch control via RS 232 interface is done by using text commands with syntax similar to the Telnet server commands described in chapter 7 Text commands accepted by LinkBone Switch 1 to 15 Dual 1 to 15 type Additionally the switch status can be configured by included RC5 infrared remote control 3 1 Front panel Figure 2 shows the front panel of the LinkBone Switch containing the following elements 1 power switch position means that power is on and O indicates that power is off 2 status indicator the blue color indicates that the device is ready for operation 3 infrared Remote Control RC sensor with RC5 decoder 4 reset button with the following functions e single button press disconnects all ports e holding down button for 5 seconds starts touch screen calibration procedure 5 RS 232 port described in chapter 6 Access through RS 232 interface 6 Ethernet port described in chapter 5 Ethernet remote control port 7 System Display with touch screen described in chapter 4 System Display System Display 1 mm U Link GZO mE gas www LinkBone com O O C lt lt a Figure 2 Front panel of the LinkBone Switch 3 2 Rear panel LinkBone Switch User manual 1 to 15 Dual 1 to 15 type Link EERE Figure 3 shows the rear panel of the Link
15. adapter System Display Figure 4 Connection of the LinkBone Switch to the power outlet To turn on the unit set the power switch position on position The status indicator will light up red After a few seconds the light color should change to blue indicating the device readiness for operation The system display will show the main screen described in chapter 4 System Display If the status indicator will not light up after power on please check the fuse on the rear panel In case of error message printed on the System Screen please contact your local sells representative in order to analyze the problem LinkBone Switch User manual 1 to 15 Dual 1 to 15 type EE Link EERE 3 4 19 Rack system mounting procedure The LinkBone Switch can be mounted in a standard a 19 rack frame using included brackets The instalation handles are fastened with four screws on both sides of the housing as shown in figure 5 Please make sure that all screws are tightened at there is no loose connection between the unit housing and the handle Four oval shaped holes on the mounting handles are used for unit installation into rack rails The equipment installation procedure in 19 rack frames is dependent on the used frame system and should be described in rack installation instructions Installation of the LinkBone Switch in 19 rack should be performed only by adequately qualified personnel Figure 5 Installation of LinkB
16. configured device new IP address for accessing configuration page od 192 168 1 5 network htn Network settings Network mode DHCP gt In DHCP mode Ip Network Mask Gateway fields are ignored ip sz e 0 Network mask 255 255 255 Gateway 192 168 1 MAC address 00 1E CO 84 31 C8 Apply changes Copyright 2014 LinkBone All rights reserved Figure 20 The network settings configuration page 5 2 Telnet Server To connect to LinkBone Switch Telnet server a client program is needed figure 21 In the address bar of the client enter the device IP address and port 23 After successful connection to the server a welcome message is displayed The system accepts text commands described in Chapter 7 Text commands accepted by LinkBone Switch 1 to 15 Dual 1 to 15 type The number of simultaneously open client Telnet sessions is limited by the server All inactive telnet sessions are closed automatically after 2 minutes in order to save system resources To keep the session alive execute one of telnet text commands before the timeout e g ping LinkBone Switch User manual 1 to 15 Dual 1 to 15 type CE Link EERE 6 Access through RS 232 interface Access through the serial interface RS 232 is done via terminal on remote computer figure 21 Before establishing the connection parameters of RS 232 serial interface need to be set as described in chapter 4 5 RS 232 settings The Link
17. e unit once a year by an authorized service center The manufacturer reserves the right to modify or completely change the operating instructions and specification of the device at any time The latest version of documentation can be found at www LinkBone com Manufacturer ZUH Kamserwis PL98 400 Wieruszow ul Kasztanowa 4 tel 48 601 743 537 EJ LinkBone Switch User manual 1 to 15 Dual 1 to 15 type Link EERE 2 Inspection of the instrument After receiving the unit please inspect if the shipping container is not damaged and the check the completeness of the delivery In case of mechanical or electrical damage please contact the sales representative The responsibility for device damages during the delivery is held by sender or carrier side The manufacturer is not liable for defects caused during transport In case of damage of shipped goods please keep the complete shipping container and filling Before the first run of the device please check that none of the instrument elements are damaged or defective Pay special attention inspecting the power adapter supplied with the unit to avoid electric shock In case of finding defect please contact sales representative Packing list LinkBone Switch 1 to 15 type AC wall adapter 12V 1000mA Infrared remote control Two mounting brackets for 19 rack installation with screws Self adhesive rubber feet for placing the device on a flat surfaces User manual LinkBone
18. ectric shock In order to connect external equipment to LinkBone Switch the user should always check the electrical and mechanical compatibility of the devices The specified voltage and current values for the connectors cannot be exceeded In case of incompatibility of electrical or mechanical properties devices should not be connected When connecting external equipment to ports with labels from A to P please use proper protection against signal reflections electrostatic discharge and other intended or unintended e g by device failure short circuits with other port lines or ground Make sure that cables being connected to the device are previously discharged to prevent damage of the equipment from ESD It is not recommended to use LinkBone Switch with sensible equipment which can be damaged by unexpected electric signals or short circuits The manufacturer is not liable for any equipment damage resulting from not using suitable protection circuits or improper use of the LinkBone Switch To reduce probability of device failure because of external noise sources shielded cables should be used Please use proper overvoltage protection to prevent damage of the equipment e g by lightning strike Use only fuse types specified for given device Do not operate the unit with the cover or any part of casing removed When the power supply is connected to LinkBone Switch do not touch elements with high voltage To change the batteries in IR remote control
19. fter the successful decode of RC5 code the message will be displayed on the screen with detected code number figure 13 To return to main screen press Back to main screen button Pressing Back to last menu button returns to IR Remote Control menu If user presses the assigned remote control button in the future the switch will change its statstate to programmed value The switch configuration includes port connection setup and the switching mode Figure 13 Message about successful assignment of RC5 code To delete assigned RC5 configuration form device memory select Delete RC5 code option Then pointing with the remote control at the RC sensor press the button to be deleted After successful decode of button RC5 code a confirmation message will be displayed figure 14 To delete the code select the Accept button The device will no longer change state after receiving the deleted RC5 code configuration The remote control button can be assigned to different configuration in the future LinkBone Switch User manual 1 to 15 Dual 1 to 15 type ES Link EERE Figure 14 RCS code delete confirmation screen To cancel program or delete procedure of the RC5 code select the Cancel button Note The RC sensor exposed to directly sunlight or other of infrared sources can lead to change of device state This effect is visible through red blinking status indicator To avoid this behavior it is recommended to disable the IR access if not used 4 4 E
20. l life witch time System display o Resolution o Touch screen IR Receiver o Accepted codes o Carrier frequency Ethernet interface o Standards O O Q O o Connector type o Supported cable types RS 232 serial interface o Baudreate Transmission type Transmission control flow Connector type Supported cable types Operating temperature Operating humidity range O 2 Fuse type Installation in 19 inch rack AC Power adapter type PSC12R 120 o Input voltage Power Output Voltage Maximum output current DC connector O 0 Q Bone 24V 1 5A 500 gold plated bistable gold clad isolated from external atmosphere minimum 10 maximum 10ms 128x64 yes RC5 standard 38Khz 10Base T 100Base TX Auto MDIX Auto negotiation RJ45 STP Cat5E up to 100m length 9600 19200 38400 57600 115200 asynchronous full duplex RTS CTS none female 9 pin D sub D sub shielded extension cable 0 40 C lt 90 below 35 C lt 60 above 35 C 5x20mm fast blow type current rating 500mA yes 100 240 VAC 50 60Hz 12W 12VDC 1000mA Center positive standard LinkBone Switch User manual 1 to 15 Dual 1 to 15 type ES Link EERE 11 Appendix A Electromagnetic Compatibility INSTYTUT AUTOMATYKI SYSTEM W UN PCA ENERGETYCZNYCH Sp z 0 0 SY A a Rok za o enia 1949 Centrum Badawczo Rozwojowe HAC MRA ma ul Wystawowa 1 51 618 Wroc aw Bio gt A tel centrala 71
21. ly connected together e lt ports gt parameter species one or more ports with labels from a to o or A to O e g on d or off A E In single mode on command only accepts one port name at the time e By default all inactive Ethernet connections are terminated after 120 second timeout To keep connection active use one of device commands before timeout e g ping e When sending a new command the client should wait for completion acknowledge of the previous command by receiving appropriate message e g Done LinkBone Switch User manual 1 to 15 Dual 1 to 15 type 23 Link EERE 8 Device cleaning Before starting cleaning the instrument disconnect all attached cables Make sure that power cable is disconnected Clean the unit only with a lint free dry cloth Please take care to not scratch the display when cleaning 9 Product recycling The LinkBone Switch complies with the requirements of ROHS standard concerning the use of hazardous materials The product should be disposed by transferring to the recycling point in accordance with local law regulations To obtain information regarding disposal requirements please contact your local authorities m LinkBone Switch User manual 1 to 15 Dual 1 to 15 type 10 Specifications Characteristics of A to P ports o Maximum input voltage o Maximum current o Impedance o BNC XLR pin contact Internal switch specification o Switch type Contact material Expected mechanica
22. one Switch mounting handles for 19 rack systems 10 LinkBone Switch User manual 1 to 15 Dual 1 to 15 type Link EERE 4 System Display The System Display is located on front panel of the LinkBone Switch The user can control device state via touch screen interface Do not use sharp objects for interacting with the touch screen to avoid scratches or damage of the touch layer 4 1 Main screen Figure 6 The main screen The main screen figure 6 shows the current state of the port connections and the mode of operation Lines drawn between filled boxes with port name label represent port connections Disconnected ports are displayed with boxes with no fill To modify connections tap on the connection state illustration The screen with A to O buttons representing ports figure 7 will be displayed Highlighted key means that the port is connected to the common node P Buttons with no fill mean that the port is disconnected Changing the port status is done by taping the button with the port letter The update of internal switches is done immediately after the button is released To return to the main screen select the lt key Figure 7 The switch state configuration screen The information about currently selected switching mode is displayed in lower left corner of main screen The switching mode operation is described chapter 3 Device description By taping on mode button user can select two switch configurations e
23. single mode indicates that the device is operating in single mode e multi mode indicates that the device is operating in a multi LinkBone Switch User manual 1 to 15 Dual 1 to 15 type w Link EERE The change of switching mode is reflected during the next port switch sequence To access the device Settings menu tap on the button on bottom right corner of the main screen figure 8 Settings menu contains the following items e Screen System Display settings described in chapter 4 2 Screen settings e IR Remote Control infrared remote control options The RC5 IR remote control is described in chapter 4 3 Infrared Remote Control settings e Ethernet the Ethernet interface configuration described in chapter 4 4 Ethernet settings e RS 232 the RS 232 interface configuration described in chapter 4 5 RS 232 settings e System info information about software and hardware version and serial number of the device e Return returns to the main screen Figure 7 Settings Menu If there are more items in the menu than is possible to display on single screen a navigation slider is drawn on the left side of the screen The user can navigate between menu pages using the arrow keys on the slider figure 8 Figure 8 Second part of the Settings Menu a LinkBone Switch User manual 1 to 15 Dual 1 to 15 type Bone 4 2 Screen settings Figure 9 Screen menu The Screen menu shown on figure 9 includes
24. thernet settings Figure 15 Ethernet port settings The Ethernet settings menu figure 15 contains the following items e Button specifying the Ethernet port mode with two possible values o Mode DHCP device operates in DHCP client mode The DHCP server assigns the IP address subnet mask and default gateway In this mode it is not possible to modify other Ethernet port settings o Mode static device works with static IP address subnet mask and default gateway assigned by the user The device Ethernet mode settings are updated after the pressing the Accept button by user e Pxx xx xx xx displays IP address specified by the user or assigned by a DHCP server e MASK xx xx xx xx displays the subnet mask specified by the user or assigned by a DHCP server e GW xx xx xx xx displays the default gateway specified by the user or assigned by a DHCP server e Accept update of the device Ethernet settings e Cancel cancel modification of Ethernet settings 8 LinkBone Switch User manual 1 to 15 Dual 1 to 15 type Link EERE In Ethernet static mode by taping on the IP subnet mask and default gateway parameter buttons the user can modify related setting value The edit window is shown on figure 16 At the top of the screen edited parameter is displayed The user can edit parameter value by using the numerical keys and navigate between positions by using or gt buttons To confirm the changes select Ok button
25. urning on the device for the first time to prevent personal injury or damage of equipment The manufacturer does not take responsibility for any instrument damages or personal injuries caused by not restricting the device operation instructions and specifications The LinkBone Switch must be only used with the power adapter provided by the manufacturer The device should be operated at temperature range from 0 to 40 C and low humidity environment Ensure adequate air circulation to prevent overheating of the device During operation the device all its components must be always dry and used in an atmosphere free of conductive pollution The operating atmosphere should not contain explosive and corrosive gases In case of suspected device failure or any other hazardous situation the user should immediately stop the operation of the device Keep all elements of the system away from children The device should not be exposed to direct sunlight In case of spilling liquid on the equipment immediately disconnect the power supply and discontinue its use During installation please note that device housing and all connectors are connected to the negative rail of the power supply adapter marked as or ground on the 12VDC connector Do not short the device ground to elements with different electric potential e g by connecting device housing or external cables Touching device ground and elements with the different electric potential can result in el
Download Pdf Manuals
Related Search