INSTRUCTION MANUAL
Contents
1. page 14 6 SERVO DIRECTION T page 15 7 SETTING CPA Center Point Adjustment FUNCTION page 15 8 SETTING EPA END POINT ADJUSTMENT FUNCTION page 15 9 ADJUSTMENT OF THROTTLE FUNCTION S CURVE page 16 10 ARBITRARILY SHAPE CURVE SETTING page 16 11 THROTTLE AND GYRO SENSITIVITY LOCK page 16 12 MIXING FUNCTION page 17 13 STICK CALIBRATION AND LEFT RIGHT HAND MODE page 17 14 SELF HELP MOVEMENT OUT OF CONTROL FAIL SAFE page 17 15 REST SETTING page 18 page 2 THE MAIN FEATURES N 7 Digital Synthesis There is no need to replace crystal Automatic frequency selection to avoid interference with other communications Automaticly scanning receivers High sensitivity and high performance anti jamming combination PCM 1024 high accuracy and large range jumping to the total elimination of drift and rudder problems Large screen liquid crystal display with backlight Through the user interface settings menu you can adjust all parameters Programming give the possib2. J AUX2 CH8 BATTERY 3 AUX1 CH7 Flap Servo CH6 UBEC SWITCH Landing Gear Servo CH5 Rudder Servo CH4 ANTENNA 3 Throttle Servo CH3 Elevator Servo CH2 RECEIVER F Aileron Servo CH1 page 13 2 OPERATION READY 1 Befor turning on your transmitter make sure the throttle on the lowest position switch D R to position 1 and IDLE to position N 2 After power ON using the or key you can adjust the screen brightness 3 Check the battery voltage to ensure that the voltage is normal If the battery symbol is flashing and accompanied by the sound alarm you need to replace the battery 4 Check PCM PPM Modulation type model and his name accordingly to the guidelines in section 3 5 Observe the screen the radio columns will be changed continually according to the movements of the control stick and the controlled channel is indicated on the screen with cursor as below 1110 F TIME 1 j a s V ee F MODEL rcm Radio Columns ii i MOR EPA CPA CRY pate The controlled channel lt Z 10 H PA lt Sia AM ZELELE 43 11 4 800 S GYAAGEH BPH FEF 1101 XAUS 6 Press SET key 3 times the display graphics in the middle of the region will show the aircraft picture Pushing the control sticks you can observe the flying actions on display according your movemen
3. Push the aileron control stick to the maximum the right the HI will appear on the screen and blink use or key to set the end of servo s travle value 4 For example to set the end point of aileron servo s travle When EPA is blinking use CH key to select channel AIL move the aileron control stick to minimum position the left and now you can see LO appear on the screen Observe the aireron servo on your model Use or key to increase or reduce the value to meet your want Push the aileron control stick to the maximum the right the HI will appear on the screen Observe the aireron servo on your model Use or key to increase or reduce the value to meet your want Push the aileron control stick to minimum the LO will appear on the screen i IDEL Press SET key to EPA blink p A AN of sa LI 8 Use Bor key to increase or reduce i 1111 the end point value q E aA i Use CH key to select aileron channel All ZELELI JTHR FR 6 111 11 1 fale 11 80 L W TIME 111 B EPE MODEL PEM EPA w FE M I DR 1 Push the aileron control stick to maximum the EPA HI will appear on the screen GER FAL Press ENT key at the end to confirm your choice You will hear a long sound as confirmation that the value was written to memory 6 Switch D R to position 2 o
4. this time of the gyroscope sensitivity memory output value was down by Under the ENT button to confirm set from the state After the GC as long as the switch hit 2 position gyroscope sensitivity automatically to maintain output at that level do not have in flight re adjustment knob Channel 5 12 MIXING FUNCTION Press SET key until TYPE is blinking Next press ENT key to confirm you choice then press SET key to have MIX blinking AIL MIX will display on the sreen This means that the master servo is AIL MIX servo User can select any other servos as master ELE MIX THR MIX RUD MIX GEA MIX FLP MIX AUX1 MIX AUX2 MIX to do that he need press SEL key The CH line display the master mixing control servo Pressing CH change the slave servo to mix with master Next user need to adjust the rate of mixing with or keys At the end press ENT You will see the screen asking you YES NO After selecting YES will blink press ENT to confirm 13 STICK CALIBRATION AND STICK MODE Important remarque User should make a stick calibration before to make a change to stick mode To make a stick calibration first move all sticks aileron throttle rudder and elevator to middle position Push SET key until TYPE is blinking then press SEL CH key MOD1 will display Push or and shorty after when STK AIM is on screen push ENT To change left right hand mode press SET key until TYPE is blinking then press SEL CH key MOD1 will display o
5. E blinking characters said Into the lock throttle to set the value of the state of throttle push rod engine to idle operation the number of field observation showed that at this time of the stroke volume Speed in an appropriate value the TC will switch hit 2 THR HOD position the current value of the gas output was down memory the process can be repeated until a satisfactory value of the throttle lock the final press ENT button to confirm Set from the state Just after 2 position of TC hit switches power output would automatically be maintained at this level 12 MIXING FUNCTION Press SET key until TYPE is blinking Next press ENT key to confirm you choice then press SET key to have MIX blinking AIL MIX will display on the sreen This means that the master servo is AIL MIX servo User can select any other servos as master ELE MIX THR MIX RUD MIX GEA MIX FLP MIX AUX1 MIX AUX2 MIX to do that he need press SEL key The CH line display the master mixing control servo Pressing CH change the slave servo to mix with master Next user need to adjust the rate of mixing with G or keys At the end press ENT You will see the screen asking you YES NO After selecting YES will blink press ENT to confirm 13 STICK CALIBRATION AND STICK MODE Important remarque User should make a stick calibration before to make a change to stick mode To make a stick calibration first move all sticks aileron throttle rudder and elevator
6. ECTING page 6 4 MODEL NAME FUNCTION T page SET THE TYPE OF AIRCRAF page 6 SERVO DIREC ION page 8 7 SETTING CPA Center Point Adjustment FUNCTION page 8 8 SETTING EPA END POINT ADJUSTMENT FUNCTION page 8 9 ADJUSTMENT OF THROTTLE PITCH FUNCTION S CURVE page 9 10 ARBITRARILY SHAPE CURVE SETTING page 10 11 THROTTLE AND GYRO SENSITIVITY LOCK page 10 12 MIXING FUNCTION T page 11 13 STICK CALIBRATION AND LEFT RIGHT HAND MODE q page 11 14 SELF HELP MOVEMENT OUT OF CONTROL FAIL SAFE page 12 15 REST SETTING U page 12 FIXED WING AIRCRAFT 1 INSTALLATION DIAGRAN page 12 2 OPERATION READY n 2 22 n nonane n nn nnn nn nnn nana nnn ne page 13 3 FLYING TIME SETTING MODEL AND MODULATION PCM PPM SELECTING page 13 4 MODEL NAME FUNCTION page 14 SET THE TYPE OF AIRCRAF
7. INSTRUCTION MANUAL For T810 2 4GHz PCM1024 8 Channel RADIO CONTROL SYSTEM For Airplanes Helicopters gt P aa a DIGITAL RADIO CONTROL SYSTEM TIME 0 000 wp MODEL PCM SERVO Le A Lt ot TYPE REV EPA CPA CRV i i 4680 11 s IDL N D R 1 8 Channel CE0678 Thank you for purchasing digital model T810 remote control This manual will give you specific guidance in order to ensure that you enjoy the advantages provided by the various functions Please read this carefully before using the manual THE USE OF ALL SAFETY PRECAUTIONS AND NOTES 1 In the operation of this radio please be sure to read before this manual 2 The remote control device is not children s toys All systems need to be assembled correctly and tested before the operation in order to avoid the accident The owner must adopt the safest way to control the operation of model The inappropriate operation may cause serious personal injury or property damage Owner must assume full responsibility for the accident Because we cannot control assembly of model s system we cannot be hold responsible of acccident 3 The use of external power supply do directly charge the battery of transmitter is prohibited 4 If need to use A C charger you must disconnect the battery from transmitter never charge at a rate higher than 1000mAh 1 Amp 5 Before power on the transmitterthrottle must move to a minimum positio
8. OR or Reverse REV i iv TIME 11 1111 2 MODEL Pom SERVO re ll TYPE WOR EPA CPA CAN m o MI i gt IDL N 11 Ll nm TAIL Z ELELE 3 113 RUD SYR GER K PHFLP AUR th AUR NOTE User must check and correct all servo direction before flight Wrong servo direction movement may cause a crash 7 SETTING CPA Center Point Adjustment FUNCTION This fuction ues to adjust the center of the servos installed in your model 1 Move the channel stick you want to the middle position 2 Press SET key to SERVO blink then press ENT key one time next press SET again until CPA is blinking 3 Use CH key to select the channel you want to adjust Next press or key to select the servo you want to adjust CPA point Press ENT key to confirm You will hear long sound as confirmation 8 SETTING EPA END POINT ADJUSTMENT FUNCTION 1 It is to adjust the end of individual servo s travle The range for HI position is from 0 125 and for LO position is 125 0 2 Switch D R to position 1 IDLE to position N TC to position 0 3 Press SET key to SERVO blink When Servo is blinking press ENT key Next press SET key until EPA is blinking Use CH key to select the channel you want to adjust Move switch the control stick of channel you selecting to minimum and you can see LO appear on the screen and blink now use or key to set the end of servo s travle value When the EPA is blinking Push the a control
9. djustment TC Throttle Control switch 1 Throttle free O Throttle cut 2 Throttle hold 8 GC Gyroscope sensitivity control switch N Oo WN 1 Gyro free 0 Gyro cut 2 Gyro hold 9 D R Dual Rates Settings 10 IDLE Used to set THROTTLE curve and PITCH curve for idle state during the flight 11 AUX1 7 channel control switch 12 AUX2 8 channel control switch HELICOPTER SYSTEM SETTING 1 INSTALLATION DIAGRAM ai J AUX2 CH8 BATTERY UJ AUX1 CH7 Pith Or Flap Servo CH6 SWITCH Gear Servo Or Gyro CH5 Rudder Servo CH4 ANTENNA 1 Throttle Servo CH3 Elevator Servo CH2 RECEIVER m Aileron Servo CH1 page 5 2 OPERATION READY 1 Befor turning on your transmitter make sure the throttle on the lowest position switch D R to position 1 and IDLE to position N 2 After power ON using the or key you can adjust the screen brightness 3 Check the battery voltage to ensure that the voltage is normal If the battery symbol is flashing and accompanied by the sound alarm you need to replace the battery 4 Check PCM PPM Modulation type model and his name accordingly to the guidelines in section 3 5 Observe the screen the radio columns will be changed continually according to the movements of the control stick and the controlled channel is indicated on the screen with cursor as below Radio Columns The controlled channel 6 Press SET key 3 times the disp
10. ease the button until the indicator light to turn on it will lift the self storage process moves 15 RESET SETTING Press SET key to SERVO blink then press down SEL CH keys and You will hear DI sound as confirmation CONTENTS Transmitter 310 PCM1024 2 4GHz Modulation mode DSSS Operating system 2 stick 8 channel system Power supply 11 1V Li Poly battery Power consumption 300mA RECEIVER R810 8 channels receiver of DSSS system receiving on 2 4GHz band Power requirement DC5V or DC6V Power consumption 30mA Note Never use dry battery for T810 please use Li Poly battery for R810 page 19
11. he or keys to select a model name storaged in system 9 mode names storaged in the memore To renamed the model Press CH SEL key when MODEL blink Choose a character for the first letter of model s name by using or key Press SET key to choose next character in the same way You can use up to 6 character for the name For example for three letter name F16 5 SET THE TYPE OF Helicopters 1 Press SET key to TYPE blink press or key to select ACRO HELI then press ENT key to confirm After you select HELI the next step in will be a choice of type of Helicopter Four typical configuration are provided Standard two 120 degrees of swash plate and one 90 degrees Cross set the standard Normal 120 degrees swash plate three point cross set CCPM Inverse 120 degrees swash plate 90 degree swash plate CCPM three 120 degree CCPM 2 If your model doesn t belong to any one of this you need to use option DIY and provide the information about your heli using mixing ee of transmitter GR AUD 3 GYR GER 0 1 11 1141 TAN page 3 When setting is finished move the stick the plane s actions will be shown on the screen according to your controls 6 SERVO DIRECTION To reverse servo direction following to the following steps Press SET key to SERVO blink then press ENT key When the REV NOR blinking on the LCD screen Next press CH key to select the channel you wish to change Push or key to make the servo
12. ility to control a variety of aircraft types And the proportion of action to respond to manipulation of any adjustable curve Can switch in flight will also be able to meet the needs of learners with special needs User programmable mixed control mode To meet the exigence of variety types of helicopters In case of airplanes possibility of controlling V shaped tail Delta wing as well as other special needs to control the model 9 memory storage 8 Fail safe setting 9 Throttle cut RECEIVER S ANTENNA INSTALLATION MPORTANT Since the 2 4GHz have different characteristics than that of the conventional 27MHz and 72MHz frequencies please read this carefully to enjoy safe flight with the 2 4GHz system 1 Keep the antenna away from the motor ESC and other noise sources as much as possible Be very careful when handling the receiver antennas Repeated motion in and out of the case holes or excessive pulling forces could break or compromise the internal antenna connections The antenna should be placed at a 90 degree angle to the centre AXIS of model This is not a Critical figure but is very important to have a good range The antenna must be kept away from conductive materials such as metal and carbon by at least a half inch The coaxial part of the antennas does not need to follow these guidelines but do not bend it in a small radius If the fuselage is made of conductive material such as metal and carbon
13. k Use CH key to select THR channel The screen graphics display area will display throttle curve Press ENT key into the curve adjustment function The middle point of the curve will blink Using or key to change the middle point range of curve Press SET key to select next of 5 point 3 You can set different shape of curve for each position of IDLE switch 1 2 At the end press ENT key to confirm your choice Exactly in the same you can adjust pitch curve 10 ARBITRARILY SHAPE CURVE SETTING Normal user can set a shape of 5 point curve by edition of linear curve If the user needs any arbitrary curve s shape he need to proceed as follow You need to be in CRV submenu press Enter at moment when you see the CRV blinking In that moment you need to press and key at the same time In this manner you enter to the menu in which you can make the adjustement more points Pressing SET key you can select each of this point and using the or key you can adjust its position In addition to the throttle and pitch channel all channels 1 8 curves can be set up to improve quality of control Each channel can be set up to 3 different curves in relation to osition of D R switch in order to change the flight pattern posit W g gnt p page 17 11 IHROTTLE AND GYRO SENSITIVITY LOCK Switch IDLE to N TC switch to 1 On the screen display you will see THR FRE at the same time by holding down both the and keys so that the key to THR FR
14. lay graphics in the middle of the region will show the aircraft picture Pushing the control sticks you can observe the flying actions on display according your movements First user must know how to use the control stick to control the helicopter 7 Atthe beginning switch TC to 0 position throttle cut before connecting power to the model After finishing checking switch to position 1 for ready to fly 8 Power On the receiver and check if the receiver indicator light is on If the receiver light does not shine press the receiver SCAN button Diode will start flashing and then press SCAN button on RF Module of transmitter The diode of the RF module will start flashing as well If the both light are continuosly ON on transmitter and receiver you can use your radio 3 FLYING TIME SETTING MODEL AND MODULATION PCM PPM SELECTING Pushing SEL key you will see on display top blinking menu item in order TIME MODEL PCM PPM Blinking menu item is selected When TIME is blinking pushing or button you can adjust the actual flight time Use the ENT key to confirm your selection If MODEL is blinking using the or key you can select models Seeing the PCM PPM item blinking using the or you can change type of modulation from PCM to PPM and inversely NOTE When you fly a model you must select PCM mode as PPM mode is only for the use of simulator page 6 4 MODEL NAME FUNCTION Press SEL key to MODEL blink then press t
15. mprove quality of control Each channel can be set up to 3 different curves in relation to position of D R switch in order to change the flight pattern THROTTLE AND GYRO SENSITIVITY LOCK 1 Throttle lock value adjustments Switch IDLE to N TC switch to 1 On the screen display you will see THR FRE at the same time by holding down both the and keys so that the key to THR FRE blinking characters said Into the lock throttle to set the value of the state of throttle push rod engine to idle operation the number of field observation showed that at this time of the stroke volume Speed in an appropriate value the TC will switch hit 2 THR HOD position the current value of the gas output was down memory the process can be repeated until a satisfactory value of the throttle lock the final press ENT button to confirm Set from the page 11 state Just after 2 position of TC hit switches power output would automatically be maintained at this level 2 In accordance with the above mentioned in the same way you can adjust the flight pattern of N 1 2 under the gyroscope sensitivity value of the lock pulled GC switch to 1 on the screen display you will see GYR FRE at the same time and then hold down both the and keys GYR FRE characters blinking into the lock set value of the state of rotation 5 Gyroscope channel knob adjustment sensitivity to the appropriate location GC will switch hit 2 GYR HOD at
16. n and TC must switch to 0 6 If you are not sure to have the ability to operate RC system we recommend that you look for an experienced RC pilot or you can join the local Modelist Club in order to obtain the necessary support knowledge and skills Product manufacturers and distributors are not responsible for any accident that is result of your leak of knowleagde 7 Children under 12 cannot use the product 8 G2 G3 XTR FMS is compatible with the remote control and other software simulator However you need to buy a separate cable PACKAGE CONTENTS This package includes 1 T810 8 channel transmitter with RF module x set 2 R810 8 channel PCM Receiver x 1piece 3 English user manual x 1 page 1 THE USE OF ALL SAFETY PRECAUTIONS AND NOTES T page 1 PACKAGE 60 1 45 5 page 1 4 06 lt page 2 THE MAIN FEATURES Y page 3 RECEIVER S ANTENNA INSTALLATION page 3 KEY FUCTIONS 92 92 92 nn nnn nnn nnn nnn nnn nnn page 4 HELICOPTERS SYSTEM SETTING 1 INSTALLATION DIAGRAN page 5 2 OPERATION READY 2 22 n nonane nn nn nana nnn nn nnn nanan page 6 3 FLYING TIME SETTING MODEL AND MODULATION PCM PPM SEL
17. n the screen Pressing or key will display MOD2 At moment you see MOD2 push ENT key To verify if the mode really has change move Trottle stick Moving Trottle key should display small triangle above Trottle channel on display Note If you change the stick mode peease make stick calibration page 12 14 19 SELF HELP MOVEMENT OUT OF CONTROL FAIL SAFE Model lost in the remote control transmitter signal when the implementation of dynamic self help movement This action is stored in a set of 8 channel receiver by the user to set their own store Method Open the first remote control transmitter receiver after the opening to ensure that the receiver Always light can be normal to accept instructions Press the button on the receiver to keep 2 seconds until the light is off said the store began to manipulate the action this time to send button to open soon in the remote control transmitters operate on self help movement to do that in 5 seconds after the re turn on the light before the operation In the remote control transmitter made on the operation of action will be down the memory If the indicator light turns off so that the buttons did not release the button until the indicator light to turn on it will lift the self storage process moves RESET SETTING Press SET key to SERVO blink then press down SEL CH keys and You will hear DI sound as confirmation FIXED WING AIRCRAFT INSTALLATION DIAGRAM
18. o select THR channel The screen graphics display area will display throttle curve Press ENT key into the curve adjustment function The middle point of the curve will blink Using or key to change the middle point range of curve Press SET key to select next of 5 point 3 You can set different shape of curve for each position of IDLE switch 1 2 At the end press ENT key to confirm your choice Exactly in the same you can adjust pitch curve 4 The following charts are the samples for different flight mode throttle pitch curve for reference NORMAL FLIGHT PATTERNS Throttle Curve Pitch Curve FLIGHT MODEL 1 Throttle Curve Pitch Curve page 10 Flight Model 2 Throttle Curve Pitch Curve 5 You can see the curve of each Flight Model on screen moving the stick after finishing the setting 10 ARBITRARILY SHAPE CURVE SETTING 1 Normal user can set a shape of 5 point curve by edition of linear curve If the user needs any arbitrary curve s shape he need to proceed as follow You need to be in CRV submenu press Enter at moment when you see the CRV blinking In that moment you need to press and key at the same time In this manner you enter to the menu in which you can make the adjustement more points Pressing SET key you can select each of this point and using the or key you can adjust its position In addition to the throttle and pitch channel all channels 1 8 curves can be set up to i
19. operate normally NOR or Reverse REV tie TIME FPO lt MODEL PEM SERVO Ki LIL HPA EPA CPA CHW 7 SETTING CPA Center Point Adjustment FUNCTION This fuction ues to adjust the center of the servos installed in your model 1 Move the channel stick you want to the middle position 2 Press SET key to SERVO blink then press ENT key one time next press SET again until CPA is blinking 3 Use CH key to select the channel you want to adjust Next press or key to select the servo you want to adjust CPA point Press ENT key to confirm You will hear long sound as confirmation MODEI 11 14 CPA is blinking ERVO ____ TYPI F einige g amas oa A ees 1114 H Channel and a WR CPA position gt 3 THA 41118 SURGE 011 401 11181 8 SETTING EPA END POINT ADJUSTMENT FUNCTION 1 It is to adjust the end of individual servo s travle The range for HI position is from 0 125 and for LO position is 125 0 2 Switch D R to position 1 IDLE to position N 3 Press SET key to SERVO blink When Servo is blinking press ENT key Next press SET key until EPA is blinking Use CH key to select the channel you want to adjust Move switch the control stick of channel you selecting to minimum left or down and you can see LO appear on the screen and blink now use or key to set the end of servo s travie value page 8 When the EPA is blinking
20. r 3 you can set the EPA rate 0 100 separately of aileron elevator rudder gyro sensitivity and AUX1 AUX2 You can change this amount of servo s travel in flight For D R2 and 3 you don t need put the sticks to maximum minimum position Do the same way as steps above to select EPA When the EPA is blinking D R 2 or D R 3 will appear on the screen use CH key to select the channel you want use or key to set the value and press ENT key at the end to confirm Select EPA to blink Use Mor key to increase or reduce the rate value 6 Switch IDEL to position 1 or 2 you can set the EPA rate 0 100 separately of throttle and pitch You can change this amount of servo s travel in flight For IDEL1 and 2 you don t need put the sticks to maximum minimum position Do the same way as steps above to select EPA page 9 When the EPA is blinking IDLE 1 or IDLE 2 will appear on the screen use CH key to select the channel you want use or key to set the value and press ENT key at the end to confirm I lt Wi Select EPA to blink 2 lt gt gt Soe Se lt lt lt Se Sas Use or key to increase or reduce the rate value 9 ADJUSTMENT OF THROTTLE PITCH FUNCTION S CURVE 1 Before adjustemt wwitch IDLE to N and TC to 0 2 Press SET key and next press ENT key SERVO will be blinking Next press SET key until CRV start to blink Use CH key t
21. stick to the maximum the right the HI will appear on the screen and blink use or key to set the end of servo s travle value 4 Press ENT key at the end to confirm your choice You will hear a long sound as confirmation that the value was written to memory page 16 Fush the 24241 4134 stick s miner the LC iB on the screen ACRO 4 8 ink H 22501 feed hairy Ez inc 1 AR aa Fa 431 vee nm i 11 j t Ahin IPE TER EPIMFLE TUJI 21180 Ci e EER 4 5 c s nominal stick to mainen j ae MODEL Pew EPH will appear on sanan 2051 TYPE i I ACRO WE 1011 F LA GA 41118 BK 5 Switch D R to position 2 or 3 you can set the EPA rate 0 100 separately of aileron elevator rudder gyro sensitivity and AUX1 AUX2 You can change this amount of servo s travel in flight For D R2 and 3 you don t need put the sticks to maximum minimum position Do the same way as steps above to select EPA When the EPA is blinking D R 2 or D R 3 will appear on the screen use CH key to select the channel you want use or key to set the value and press ENT key at the end to confirm 9 ADJUSTMENT OF THROTTLE FUNCTION S CURVE 1 Before adjustemt wwitch IDLE to N and TC to 0 2 Press SET key and next press ENT key SERVO will be blinking Next press SET key until CRV start to blin
22. the antennas part must be placed outside of the fuselage In addition to that do not attach the antenna part on the fuselage Installing the RECEIVER into that kind of fuselage this guideline must be kept Antenna Coaxial cable KING MAX SCAN LED R810 Autoscan 2 4 GHz RECEIVER WWW HK8WIFT COM N QO h QO 4 page 3 TC Antenna GC Buzzer IDLE D R AUX1 AUX2 PIT FLP GYR GER Throttle Mode2 Elevator Mode1 Throttle Trim Lever Rudder Stick Model Elevator Trim Lever Mode2 Throttle Trim Lever Mode2 Elevator Trim Lever Model Rudder Trim lever Throttle Mode1 Elevator Mode2 aileron Stick Aileron Trim lever Power Switch ee v TIME k MODEL PCM SEL 6658 0 TYPE WN REV EPA CPA CRV ACRO MIX 7 Dad IDL N i SET D R 1 b ENT CH TAIL 2 ELE LE 3THR 4RUD 5 GYR GER 6 PIT FLP 7ZAUX1 B AUX2 moy ae Peso i ene 8 Channel LCD x Handle RF Module ISTAT w gt Simulator Jack Battery Cover DC 12V Jack not for charging page 4 1 SEL To Select model to adjust the time radio frequency modulation and frequency channel and so on SET To select the menu function the parameters of servos or the type of aircraft and so on CH The choice of channel Toincrease the value of parameters To decrease the value of parameters ENT button to confirm the a
23. the memore To renamed the model Press CH SEL key when MODEL blink Choose a character for the first letter of model s name by using or key Press SET key to choose next character in the same way You can use up to 6 character for the name For example for three letter name F16 5 SET THE TYPE OF AIRCRAFT Press the SET button until TYPE is blinking Next using or key select ACRO Use ENT button to confirm In the next step pressing or you can make a choice between different configuration of airplane like V tail delta and so on If your airplane doesn t belong to this categories of airplane use DIY and set up your own mixed control configuration Delta wings and flying wings V tail CH 1 aileron CH2 elevator CH2 elevator CH4 rudder Glider CH1 left aileron CHT right aileron Select the control mode after the press ENT button to confirm that there will be a menu asked YES NO With or button to select YES to YES flashes can be recognized In the adjustment or to see the type of aircraft from promoting the stick on the screen to see the aircraft control surface dynamic presentation page 15 6 SERVO DIRECTION To reverse servo direction following to the following steps Press SET key to SERVO blink then press ENT key When the REV NOR blinking on the LCD screen Next press CH key to select the channel you wish to change Push or key to make the servo operate normally N
24. to middle position Push SET key until TYPE is blinking then press SEL CH key MOD1 will display Push or and shorty after when STK AIM is on screen push ENT To change left right hand mode press SET key until TYPE is blinking then press SEL CH key MOD1 will display on the screen Pressing or key will display MOD2 At moment you see MOD2 push ENT key To verify if the mode really has change move Trottle stick Moving Trottle key should display small triangle above Trottle channel on display Note If you change the stick mode peease make stick calibration page 18 14 SELF HELP MOVEMENT OUT OF CONTROL FAIL SAFE Model lost in the remote control transmitter signal when the implementation of dynamic self help movement This action is stored in a set of 8 channel receiver by the user to set their own store Method Open the first remote control transmitter receiver after the opening to ensure that the receiver Always light can be normal to accept instructions Press the button on the receiver to keep 2 seconds until the light is off said the store began to manipulate the action this time to send button to open soon in the remote control transmitters operate on self help movement to do that in 5 seconds after the re turn on the light before the operation In the remote control transmitter made on the operation of action will be down the memory If the indicator light turns off so that the buttons did not rel
25. ts First user must know how to use the control stick to control the airplane iv TIME Mi 1114 MODEL pcre A CPA CRY thon atta a Pied rt 7 Atthe beginning switch TC to 0 position throttle cut before connecting power to the model After finishing checking switch to position 1 for ready to fly 8 Power On the receiver and check if the receiver indicator light is on If the receiver light does not shine press the receiver SCAN button Diode will start flashing and then press SCAN button on RF Module of transmitter The diode of the RF module will start flashing as well If the both light are continuosly ON on transmitter and receiver you can use your radio 3 FLYING TIME SETTING MODEL AND MODULATION PCM PPM SELECTING Pushing SEL key you will see on display top blinking menu item in order TIME MODEL PCM PPM Blinking menu item is selected When TIME is blinking pushing or button you can adjust the actual flight time Use the ENT key to confirm your selection If MODEL is blinking using the or key you can select models Seeing the PCM PPM item blinking using the or you can change type of modulation from PCM to PPM and inversely NOTE When you fly a model you must select PCM mode as PPM mode is only for the use of simulator page 14 4 MODEL NAME FUNCTION Press SEL key to MODEL blink then press the or keys to select a model name storaged in system 9 mode names storaged in
Download Pdf Manuals
Related Search