User manual Dishwasher ZDF11001WA
Contents
1. Make sure that the pressure of the water supply is not too low For this information contact your local water authority Make sure that the water tap is not clogged Make sure that the filter in the inlet hose is not clogged Make sure that the inlet hose has no kinks or bends The appliance does not drain the water Make sure that the sink spigot is not clogged Make sure that the drain hose has no kinks or bends The anti flood device is on Close the water tap and contact the Service After the checks are completed turn the pro gramme knob until the programme marker is aligned with programme that was in operation when the problem occurred The programme If the washing and drying results are not satisfactory Whitish streaks or bluish layers on glasses and dishes continues from the point of interruption If the problem occurs again contact the Serv ice If other alarm codes show contact the Service 10 The released quantity of rinse aid is too much Adjust the rinse aid selector to a lower position The quantity of detergent is too much www zanussi com Stains and dry water drops on glasses and dishes The released quantity of rinse aid is not suffi cient Adjust the rinse aid selector to a higher The rinse aid dispenser is empty The quality of the rinse aid can be the cause Refer to HINTS AND TIPS for other pos position sible causes The quality of the detergent can be the2. User manual MANUAL ZDF11001WA ZANUSSI Contents Safety instructions Control panel Programmes Options em dii e Ena hn Ak Hara Before first use ________________ Daily use 9 QI QI J gt Wh A Safety instructions Before the installation and use of the appliance carefully read the supplied instructions The manufacturer is not responsible if an incorrect installation and use causes injuries and dam ages Always keep the instructions with the ap pliance for future reference Children and vulnerable people safety Warning Risk of suffocation injury or permanent disability Do not let persons children included with re duced physical sensory reduced mental functions or lack of experience and knowl edge use the appliance They must have su pervision or instruction for the operation of the appliance by a person who is responsible for their safety Do not let children play with the appliance Keep all packaging away from children Keep all detergents away from children Keep children and pets away from the appli ance door when it is open Installation Remove all the packaging Do not install or use a damaged appliance Do not install or use the appliance where the temperature is less than 0 C Obey the installation instruction supplied with the appliance Electrical connection A Warning Risk of fire and electrical shock The appliance must be earthed Hints and tips
3. cause Dishes are wet The programme is without a drying phase or with a low temperature drying phase Technical information Dimensions Width Height Depth mm 600 850 625 Electrical connection Refer to the rating plate Voltage 220 240 V Frequency 50 Hz Water supply pressure Min max bar MPa 0 5 0 05 8 0 8 Water supply 1 Cold water or hot water2 max 60 C Capacity Place settings 12 Power consumption Left on mode 0 50 W Off mode 0 50 W 1 Connect the water inlet hose to a water tap with a 3 4 thread 2 If the hot water comes from alternative sources of energy e g solar panels aeolian energy use the hot water supply to decrease energy consumption Rating plate Environment concerns Recycle the materials with the symbol amp Put the packaging in applicable containers to recycle it Help protect the environment and human health and to recycle waste of electrical and electronic appliances Do not dispose appliances marked www zanussi com with the symbol with the household waste Return the product to your local recycling facility or contact your municipal office Discard correctly the packaging material Re cycle the materials with the symbol 11 www zanussi com shop K l 9 6 156966970 A 292013 MN
4. 8 Care and cleaning _____ 9 Troubleshooting 2 10 Technical information ____________ 11 Environment concerns 11 Subject to change without notice Make sure that the electrical information on the rating plate agrees with the power supply If not contact an electrician Always use a correctly installed shockproof socket Do not use multi plug adapters and extension cables Make sure not to cause damage to the mains plug and to the mains cable Should the ap pliance power supply cable need to be re placed this must be carried out by our Serv ice Centre Connect the mains plug to the mains socket only at the end of the installation Make sure that there is access to the mains plug after the installation Do not pull the mains cable to disconnect the appliance Always pull the mains plug Do not touch the mains cable or the mains plug with wet hands Only for UK and Ireland The appliance has a 13 amp mains plug If it is necessary to change the fuse in the mains plug use a 13 amp ASTA BS 1362 fuse This appliance complies with the E E C Di rectives Water connection Make sure not to cause damage to the water hoses The appliance is to be connected to the wa ter mains using the new supplied hose sets Old hose sets must not be reused www zanussi com Before you connect the appliance to new pipes or pipes not used for a long time let the water flow until it is clean The
5. cleaning pads or sol vents Internal cleaning If you regularly use short duration programmes these can leave deposits of grease and lime scale inside the appliance To prevent this we recommend to run long du ration programmes at least 2 times per month Troubleshooting The appliance does not start or it stops during operation With some problems different indicators flash continuously or intermittently at the Before you contact the Service refer to the in same time to show an alarm code formation that follows for a solution to the prob lem The start indicator flashes continuously The appliance does not fill with water The end indicator flashes 1 time intermittently The start indicator flashes continuously The appliance does not drain the water The end indicator flashes 2 times intermittently The start indicator flashes continuously The anti flood device is on The end indicator flashes 3 times intermittently Warning Deactivate the appliance before you do the checks Turn the programme knob until the programme marker is aligned with the on off indicator You cannot activate the appliance Make sure that the mains plug is connected to the mains socket Make sure that there is not a damaged fuse in the fuse box The programme does not start Make sure that the appliance door is closed Press the start button The appliance does not fill with water Make sure that the water tap is open
6. first time you use the appliance make sure that there is no leakage Use This appliance is intended to be used in household and similar applications such as Staff kitchen areas in shops offices and other working environments Farm houses By clients in hotels motels and other resi dential type environments Bed and breakfast type environments Warning Risk of injury burns electrical shock or fire Do not change the specification of this appli ance Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position Do not keep the appliance door open without supervision to prevent to fall on it Do not sit or stand on the open door Dishwasher detergents are dangerous Obey the safety instructions on the detergent pack aging Do not drink and play with the water in the appliance Control panel Do not remove the dishes from the appliance until the programme is completed There can be detergent on the dishes The appliance can release hot steam if you open the door while a programme operates Do not put flammable products or items that are wet with flammable products in near or on the appliance Do not use water spray and steam to clean the appliance Disposal A Warning Risk of injury or suffocation Disconnect the appliance from the mains supply Cut off the mains cable and discard it Remove the door catch to prevent c
7. andard programme for test institutes 3 With this programme you can wash a load with fresh soil It gives good washing results in a short time 4 Use this programme to quickly rinse the dishes This prevents the remaining food to bond on the dishes and bad odours to come out from the appliance Do not use detergent with this programme Information for test institutes For all the necessary information for test performance send an email to info test dishwasher production com Write down the product number PNC that is on the rating plate www zanussi com Options Half load decreases the programme duration and the consumption of energy and water Load the upper basket and the lower basket and decrease the quantity of detergent Activate or deactivate this option before the start of a programme You cannot acti vate or deactivate this option while a pro ramme operates ORE 9 P i This option is not applicable to Gio and Set this option when you want to wash a small f quantity of tableware and cookware This option Before first use 1 Make sure that the set level of the water 4 Open the water tap softener agrees with the water hardness in 5 Processing residues can stay in the appli your area If not adjust the water softener ance Start a programme to remove them Contact your local water authority to know Do not use detergent and do not load the the water hardness in your area baskets 2 Fill th
8. e salt container 3 Fill the rinse aid dispenser Adjusting the water softener Water hardness En German French mmol l Clarke Level degrees degrees degrees Wela GL 47 50 84 90 8 4 9 0 58 63 10 43 46 76 83 7 6 8 3 53 57 9 37 42 65 75 6 5 7 5 46 52 8 29 36 51 64 5 1 6 4 36 45 7 23 28 40 50 4 0 5 0 28 35 6 19 22 33 39 3 3 3 9 23 27 51 15 18 26 32 2 6 3 2 18 22 4 11 14 19 25 1 9 2 5 13 17 4 10 7 18 0 7 1 8 5 12 lt 4 lt 7 lt 0 7 lt 5 12 1 Factory position 2 Do not use salt at this level How to adjust the level of the water 2 Press and hold gt At the same time turn softener the knob counterclockwise until the pro 1 Make sure that the programme marker on gramme marker is aligned with amp the knob is aligned with Q 3 Release gt when 1 2 and start to flash www zanussi com 5 4 Press gt Put 1 litre of water in the salt container only for gt starts to flash the first time 1 2 and Q continue to flash Filling the rinse aid dispenser The intermittent flashing of refers to X the current set level e g 5 flashes pause 5 flashes level 5 5 Press gt again and again to change the set ting Each time you press gt the level num ber increases 6 To confirm the setting and deactivate the appliance turn the knob until the pro gramme marker is aligned with Filling the salt container Caution Wat
9. eactivate the appliance within 5 minutes all indicators goes off This helps to decrease energy consumption 1 To deactivate the appliance turn the knob until the programme marker is aligned with Q Paci 2 Close the water tap Important Let the dishes become cold before you re move them from the appliance Hot dishes can be easily damaged Hints and tips The water softener Hard water contains a high quantity of minerals that can cause damage to the appliance and bad washing results The water softener neutral ises these minerals The dishwasher salt keeps the water softener clean and in good conditions It is important to set the right level of the water softener This makes sure that the water softener uses the correct quantity of dishwasher salt and water Using salt rinse aid and detergent Only use salt rinse aid and detergent for dishwasher Other products can cause dam age to the appliance The rinse aid helps during the last rinsing phase to dry the dishes without streaks and stains Combi detergent tablets contain detergent rinse aid and other added agents Be sure that these tablets are applicable to the water hardness in your area Refer to the instruc tions on the packaging of the products Detergent tablets do not fully dissolve with short programmes To prevent detergent resi dues on the tableware we recommend that you use the tablets with long programmes Do not use mo
10. er and salt can come out from the salt container when you fill it Risk of corrosion To prevent it after you fill the salt container start a programme To adjust the released quantity of rinse aid turn the selector between position 1 lowest quanti ty and position 4 highest quantity Daily use 1 Open the water tap If the salt indicator is on fill the salt con 2 Turn the knob until the programme marker is tainer aligned with the programme you want to set If the rinse aid indicator is on fill the rinse Set the correct programme for the type of aid dispenser load and the degree of soil 3 Load the baskets 6 www zanussi com 4 Add the detergent 5 Start the programme Using the detergent Put the detergent or the tablet in compartment A If the programme has a prewash phase put a small quantity of detergent in compartment B Using the combi detergent tablets When you use tablets that contain salt and rinse aid do not fill the salt container and the rinse aid dispenser The rinse aid indicator al ways comes on if the rinse aid dispenser is empty 1 Adjust the water softener to the lowest level 2 Set the rinse aid dispenser to the lowest po sition If you stop to use the combi detergent tablets before you start to use separately detergent rinse aid and dishwasher salt do these steps 1 Set the water softener to the highest level 2 Make sure tha
11. hildren and pets to get closed in the appliance Service Contact the Service to repair the appliance We recommend only the use of original spare parts When you contact the Service ensure that you have the following information that is available on the rating plate Model PNC Serial Number On off indicator D Programme marker www zanussi com Indicators Start button gt Half load button 1 2 ERR BE Wy Programmes G Programme knob End indicator Salt indicator This indicator is off while the programme operates Rinse aid indicator This indicator is off while the programme oper ates Programme Degree of soil Programme Duration Energy Water LD Type of load phases min kWh 1 ECO CP ac 5 o 3 My 4 Normal soil Crockery and cut lery Normal soil Crockery and cut lery Heavy soil Crockery cutlery pots and pans Fresh soil Crockery and cut lery All Prewash Wash 50 C Rinses Dry Prewash 100 110 1 2 1 6 15 16 Wash 65 C Rinses Dry Prewash Wash 70 C Rinses Dry Wash 65 C 30 0 8 9 Rinse 130 150 1 4 13 15 Prewash 14 0 1 4 1 The pressure and the temperature of the water the variations of the mains supply the options and the quantity of dishes can change the values 2 With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil This is the st
12. r the type of load and for the degree of soil The correct quantity of detergent is used There is dishwasher salt and rinse aid unless you use combi detergent tablets The cap of the salt container is tight www zanussi com Care and cleaning Warning Before maintenance deactivate the appliance and disconnect the mains plug from the mains socket Dirty filters and clogged spray arms de crease the washing results Make a check regularly and if necessary clean them Cleaning the filters www zanussi com To remove filters B and C turn the handle counterclockwise and remove Pull apart filter B and C Wash the filters with water Remove filter A Wash the filter with water Before you put the filter A back make sure that there are no residues of food or soil in or around the edge of the sump Make sure that filter A is correctly positioned under the 2 guides D Assemble filters B and C Put them back in filter A Turn the handle clockwise until it locks An incorrect position of the filters can cause bad washing results and damage to the appliance Cleaning the spray arms Do not remove the spray arms If the holes in the spray arms are clogged re move remaining parts of soil with a thin pointed object External cleaning Clean the appliance with a moist soft cloth Only use neutral detergents Do not use abra sive products abrasive
13. re than the correct quantity of detergent Refer to the instructions on the detergent packaging Loading the baskets Refer to the supplied leaflet with examples of the load of the baskets First remove the items from the lower basket then from the upper basket There can be water on the sides and on the door of the appliance Stainless steel be comes cool more quickly than the dishes Only use the appliance to wash items that are dishwasher safe Do not put in the appliance items made of wood horn aluminium pewter and copper Do not put in the appliance items that can ab sorb water sponges household cloths Remove remaining food from the items To remove easily remaining burned food soak pots and pans in water before you put them in the appliance Put hollow items cups glasses and pans with the opening down Make sure that cutlery and dishes do not bond together Mix spoons with other cutlery Make sure that glasses do not touch other glasses Put the small items in the cutlery basket Put the light items in the upper basket Make sure that they do not move Make sure that the spray arms can move free ly before you start a programme Before starting a programme Make sure that The filters are clean and correctly installed The spray arms are not clogged The position of the items in the baskets is correct The programme is applicable fo
14. t the salt container and the rinse aid dispenser are full 3 Start the shortest programme with a rinsing phase without detergent and without dishes www zanussi com 4 Adjust the water softener to the water hard ness in your area 5 Adjust the released quantity of rinse aid Setting and starting a programme Setting mode i The appliance must be in setting mode to start a programme Turn the programme knob until the programme marker is aligned with a programme on the con trol panel lf comes on and gt starts to flash the appliance is in setting mode If the control panel does not show this condi tion press and hold at the same time 1 2 and D until the appliance is in setting mode Starting a programme 1 Open the water tap 2 Close the appliance door 3 Turn the knob until the programme marker is aligned with the symbol of the programme you want to set Ocomes on gt starts to flash 4 Press P to start the programme Qand gt are on Opening the door while the appliance operates If you open the door the appliance stops When you close the door the appliance continues from the point of interruption Cancelling the programme 1 Press and hold 1 2 and gt until gt starts to flash Make sure that there is detergent in the de tergent dispenser before you start a new programme At the end of the programme When the programme is completed gt comes on If you do not d
Download Pdf Manuals
Related Search