Industrial Device Server STE-604C / STE-604C
Contents
1. Figure 5 21 Authentication Antaira Technologies 42 antaira STE 604C User s Manual 5 2 1 2 Port serial setting Serial configuration Figure 5 21 Serial configuration 43 Antaira Technologies STE 604C User s Manual antaira The following table describes the labels in this screen Label Description Port Alias Remark the port to hint the connected device Interface RS232 RS422 RS485 2 wires RS485 4 wires 110bps 300bps 1200bps 2400bps 4800bps 9600bps 19200bps ie 38400bps 57600bps 115200bps 230400bps 460800bps Data Bits 5 6 7 8 Stop Bits 1 2 1 5 Parity No Even Odd Mark Space Flow Control No XON XOFF RTS CTS DTR DSR Force TX Interval Time Performance Force TX interval time is to specify the timeout when no data has been transmitted When the timeout is reached or TX buffer is full 4K Bytes the queued data will be sent 0 means disable Factory default value is 0 Throughput This mode optimized for highest transmission speed Latency This mode optimized for shortest response time Apply Activate settings on this page Antaira Technologies Table 5 14 Serial configuration 44 antaira STE 604C User s Manual Port Profile Port1 y 4001 Serial to Ethernet 0 ms 1 00 2 oo 3 00 4 Ethernet to Serial 0 ms 12. Label Description Accessible IP Setting To prevent unauthorized access by setting host IP addresses and network masks You can set the password to prevent unauthorized access from your server Factory Password setting default is no password Table 5 2 Security Antaira Technologies 20 antaira STE 604C User s Manual ES Device List 192 168 10 2 Y poti Y port2 4 porta Y port VCOM List 5 Setup Wizard d IP Collection YY System Log 21 Network Setting Device DS can connect the Network by wire a You must assign a valid IP address for DS before attached in your network environment Your network administrator should provide you the IP address and related settings The IP address must be unique within the network otherwise DS will not have a valid connection to the network You can choose from three possible IP configuration modes Static DHCP BOOTP The Factory Default IP address is 192 168 10 2 Options Help Device Firmware Wizard Wizard Wizard Notification Management Upgrade Firmware Save Load Wire M Using StaticiP P Using DHCP BOOTP Static IP Settings IPAddess 92168102 Netmask 255 255 2550 Gateway 192 168 101 DNS1 EEE DNS2 o Ethemet Mode Redundant Mode Switch Mode 1 Refresh Figure 5 7 Network Setting Antaira Technologies STE 604C User s Manual antaira The following table describes the labels in this screen Label Descr
3. Auto IP Report lo 0 seconds Ethernet Mode Redundant O Switch Figure 5 20 IP configuration Antaira Technologies 40 antaira Label STE 604C User s Manual The following table describes the labels in this screen Description DHCP BOOTP Obtain the IP address automatically from DHCP server Static IP Address Subnet Mask Assigning an IP address manually Set the subnet mask to communicate on the network Gateway Enter the IP address of the router in you network DNS Server Enter the IP address of the DNS server to translate domain names into IP address Auto IP Report The device server will report its status periodically At DS Tool gt IP collection option show the device server status The report interval is O indicate disable this setting default But you can set the other IP or Port Switch Mode Redundant When the connection between master link and LAN fails the DS can automatically switch to another LAN port within10mS and still guarantees a non stop connection Switch Daisy Chain support to reduce usage of switch ports 41 Table 5 13 IP configuration Antaira Technologies STE 604C User s Manual antaira Authentication You can set the password to prevent unauthorized access from network Input the Old password and New password to change the password Factory default is no password
4. Idle Timeout indicate disable this function Factory default value is 0 If Multilink is configured only the first host connection is effective for this setting The serial device will send TCP alive check package in each defined time interval Alive Check to remote host to check the TCP connection If the TCP connection is not alive Alive Check the connection will be closed and the port will be freed 0 indicate disable this function Factory default is 0 Table 5 8 Virtual COM Not allowed to mapping Virtual COM from web Service Mode TCP Server Mode In TCP Server Mode DS is configured with a unique Port combination on a TCP IP network In this case DS waits passively to be contacted by the device After a connection is established it can then proceed with data transmission TCP Server mode also supports up to 5 simultaneous connections so that multiple device can receive data from the same serial device at the same time Antaira Technologies 30 antaira STE 604C User s Manual DS Tool Eile Device Configuration COM Configuration Options Help Ga AE Remove Broadcast Device yaa Device 3 vcom Device Firmware i Wizard Wizard Wizard Wizard en SE a Vez DSTool Serial Settings Service Mode Notification Device List portl 192 168 10 2 Service Mode TCP Server Mode Y portl Y port2 TCP Server Mode Y port3 Y port TCP Server Settings Misc G VCOM List Idle Timeout
5. STE 604C User s Manual Table 3 1 Front panel LEDs 3 3 Serial Ports There 4 serial ports on the front panel of STE 604C showed as below DB9 connector Pin RS 232 RS 422 RS 485 eee 4 wire 2 wire 1 DCD RXD RXD 2 RXD RXD RXD 3 TXD TXD TXD DATA 4 DTR TXD TXD DATA 5 GND GND GND GND 6 DSR 7 RTS 8 CTS 9 RI RS 232 mod act as DTE Antaira Technologies Table 3 2 Pin assignment 10 antaira 5 Pin Terminal block connector 12 34 5 RETIRE 1 GND GND GND 2 RXD RXD 3 RXD RXD 4 TXD TXD DATA 5 TXD TXD DATA 3 4 Bottom Panel The bottom panel components of STE 604C are showed as below 1 Terminal block includes PWR1 PWR2 12 48V DC and Relay output 1 A 24VDC 2 Reset bottom 5 seconds for factory default Reset Button PWR1 PWR2 12 48V DC and Relay output 1A 24VDC N Figure 3 2 Bottom Panel STE 604C User s Manual Antaira Technologies STE 604C User s Manual antaira 3 5 Rear Panel The rear panel components of STE 604C are showed as below 1 Screw holes for wall mount kit 2 Din Rail kit Figure 3 3 Rear Panel Antaira Technologies 12 antaira STE 604C User s Manual Cables 4 1 Ethernet Cables The STE 604C has standard Ethernet ports According to the link type the STE 604C use CAT 3 4 5 5e UTP cables to conn
6. 2 3 00 Figure 5 21 Port Profile 45 Antaira Technologies STE 604C User s Manual antaira The following table describes the labels in this screen Label Description Flush Data Buffer After The received data will be queued in the buffer until all the delimiters are matched When the buffer is full 4K Bytes or after flush S2E data buffer timeout the data will also be sent You can set the time from 0 to 65535 seconds Serial to Ethernet Delimiter You can define max 4 delimiters 00 FF Hex for each way The data will be hold until the delimiters are received or the option Flush Serial to Ethernet data buffer times out 0 means disable Factory default is O Flush Data Buffer After The received data will be queued in the buffer until all the delimiters are matched When the buffer is full 4K Bytes or after flush E2S data buffer timeout the data will also be sent You can set the time from 0 to 65535 seconds Ethernet to serial Delimiter You can define max 4 delimiters 00 FF Hex for each way The data will be hold until the delimiters are received or the option Flush Ethernet to Serial data buffer times out O means disable Factory default is O Table 5 15 Port Profile Antaira Technologies 46 antaira STE 604C User s Manual Service Mode Virtual COM Mode In Virtual COM Mode the driver establishes a transparent connection between host and serial device
7. Hosts on a specific subnet can access the device server IP address 255 255 255 0 e g 192 168 0 2 255 255 255 0 3 Any host can access the device server Disable this function by un checking the Enable IP Filter checkbox Access IP Control List O Enable IP Filtering Not check this option will allow any IP to have assessibility Activate the IP IP Address Netmask Figure 5 26 Access IP Antaira Technologies 54 antaira STE 604C User s Manual SMTP SNMP Conf Email Server configuration includes the mail server s IP address or domain If the authentication is required specify your name and password There are 4 Email addresses that you can specify to receive the notification SNMP Server configuration includes the SNMP Trap Server IP address Community Location and Contact There are 4 SNMP addresses you can specify to receive the notification SysLog server configuration includes the server IP and server Port This option need to use with DS Tool SMTP SNMP Configuration E mail Settings Port 25 O My server requires authentication SNMP Trap Server Figure 5 27SMTP SNMP conf 55 Antaira Technologies STE 604C User s Manual System Event Conf Specify the events that should be notified to the administrator alarmed by E mail SNMP trap or system log System Event Configuration Device Event Notification Hardware Reset Cold Start O SMTP M
8. value is 0 If Multilink is configured only the first host connection is effective for this setting Alive Check The serial device will send TCP alive check package in each defined time interval Alive Check to remote host to check the TCP connection If the TCP connection is not alive the connection will be closed and the port will be freed 0 indicate disable this function Factory default is 0 Connect on Startup The TCP Client will build TCP connection once the connected serial device is started Connect on Any Character The TCP Client will build TCP connection once the connected serial device starts to send data 33 Table 5 10 TCP Client mode Antaira Technologies STE 604C User s Manual antaira Service Mode UDP Mode Compared to TCP communication UDP is faster and more efficient In UDP mode you can Uni cast or Multi cast data from the serial device server to host computers and the serial device can also receive data from one or multiple host Device ay Device Serial Settings Service Mode Notification ES Device List port ER 192 168 10 2 Service Mode X Y poti Y port2 UDP Mode Y porta Y porta UDF Settings Sa VCOM List Listening Port 4000 ER Auto Scan 3 Setup Wizard d IP Collection YY System Log Multilink Destination Host Begin Destination Host End Sending Port to e Auto Scan 2 to eQ Auto Scan Ey to eQ
9. Auto Scan 4 o o o to eQ Auto Scan gt Apply Only gt Apply and Save 7 Figure 5 15 UDP mode Antaira Technologies 34 antaira STE 604C User s Manual Notification Specify the events that should be noticed The events can be noticed by E mail SNMP trap or system log ES Device List 192 168 10 2 Y poti Y pon SNMP Settings Email Settings Syslog Settings Y port A 4 M Notified Items amp veer DCD Changed CTS Changed M Email Notification Iv Syslog Notification HSE Setup Wizard DSR Changed Port Connected d IP Collection YY System Log Al Changed 7 Port Disconnected Email to Mail Server Mail to 1 Refresh amp Apply Only gt Apply and Save Z Figure 5 16 Notification 35 Antaira Technologies STE 604C User s Manual antaira The following table describes the labels in this screen Label Description When DCD Data Carrier Detect signal changes it indicates that the modem DCD changed connection status has changed Notification will be sent When DSR Data Set Ready signal changes it indicates that the data communication DSR changed equipment is powered off A Notification will be sent When RI Ring Indicator signal changes it indicates that the incoming of a call A RI changed Notification will be sent When CTS Clear To Send signal changes it indicates that the transmission between C
10. Management Enable Goto Telnet Management SNMP Management Settings Community Location Contact Trap Server Trap Server Trap Server3 Trap Serverd 1 Refresh 2 Apply Only gt Apply and Save Figure 5 9 Management The following table describes the labels in this screen Label Description Web Management Enable To enable management from Web Click Goto Web Management button to access web Telnet Management Enable To enable management by Telnet Click Goto Telnet Management button to execute Telnet command SNMP Management Enable To enable management by SNMP SNMP Management Settings To configure SNMP related settings Table 5 4 Management Antaira Technologies 24 antaira STE 604C User s Manual Upgrade Firmware Options Help General Security Networking Notification Management Upgrade Firmware Save Load ES Device List 192 168 10 2 Y di I Browsing Upgrade Y porta Y port a VCOM List 92 Setup Wizard d IP Collection 9 System Log Firmware Image 1 Refresh en Apply Only gt Apply and Save Figure 5 10 Upgrade Firmware The following table describes the labels in this screen Label Description Browsing Browse the file and upgrade Upgrade Enable the firmware upgrade Table 5 5 Upgrade Firmware 25 Antaira Technologies STE 604C User s Manual antai
11. Original IP 192 168 10 2 HE Setup Wizard IV Using Static IP Using DHCP 3 IP Collection 9 System Log Assign Static P IP Address 192168102 Netmask 255 255 255 0 Gatway 192 168 10 2 0 DNS P DNS2 P eQ Auto Scan or gt Cancel OK Cancel Clear All elect Add 7 Alot of IPs need to be re config Click here 2 Your best choice Group IP Wizard Figure 5 4 17 Antaira Technologies STE 604C User s Manual antaira 5 1 2 2 Configure device servers General settings This page includes the setting of device name SNTP server and Auto IP Report Security Networking Notification Management Upgrade Firmware Save Load ES Device List 192 168 10 2 Power Y portl STE 1m 20 Y port2 3 Y port3 LAN IP Address LAN MAC Address Version Networking Y port 192 168 10 2 00 1E 94 5E 00 1E 1 03 1B 20 a VCOM List F Setup Wizard 8 Locate On d IP Collection System Log Device Name Location STE 604C M Using SNTP Time Server Auto IP Report 1 Refresh Figure 5 5 General settings Antaira Technologies 18 antaira STE 604C User s Manual The following table describes the labels in this screen Label Description You can set the device name or related information By clicking Locate On button you Device Name location can locate the serial server s position Set SNTP Input the SNTP server domain name or IP address port and se
12. User s Manual When an unauthorized access from the Console or Web interface a notification will be sent IP Address Changed When IP address of device changed a notification will be sent Password Changed When password of device changed a notification will be sent Access IP Blocked When the host accesses the device with blocked IP addresses a notification will be sent Redundant Power Change When status of power changed a notification will be sent Redundant Ethernet When status of Ethernet port changed a notification will be sent Change DCD changed When DCD Data Carrier Detect signal changes it indicates that the modem connection status has been changed A Notification will be sent DSR changed When DSR Data Set Ready signal changes it indicates that the data communication equipment is powered off A Notification will be sent RI changed When RI Ring Indicator signal changes it indicates an incoming call Notification will be sent CTS changed Port connected When CTS Clear To Send signal changes it indicates that the transmission between computer and DCE can proceed A notification will be sent In TCP Server Mode when the device accepts an incoming TCP connection this event will be trigger In TCP Client Mode when the device has connected to the remote host this event will be trigger In Virtual COM Mode Virtual COM is ready to use A notification wil
13. can establish a TCP connection with server by the method you have settled Startup or any character After the data has been transferred device can disconnect automatically from the server by using the TCP alive check time or Idle time settings File Device Configuration COM Configuration Options Help Ma 21 Add Remove Broadcast Device Device py l DSTool Serial Settings Service Mode Notification ES Device List portl 192 168 10 2 Service Mode TCP Client Mode Y portl Y porta TCP Client Mode Y porta Y port TCP Client Settings Misc lt a VCOM List Idle Timeout 0 0 65535 Seconds Gta Setup Wizard Destination Host Port i Alive Check 420 0 65535 Seconds s ru 4000 eQ Auto Scan Connect on Startup y IV Enable Control Port 4001 Multilink Destination Host Port 1 e Auto Scan 2 e Auto Scan 3 eQ Auto Scan 1 Refresh gt Apply Only gt Apply and Save Figure 5 14 TCP Client mode Antaira Technologies 32 antaira STE 604C User s Manual The following table describes the labels in this screen Label Description Destination Host Set the IP address of host Port Set the port number of data port Idle Timeout When serial port stops data transmission for a defined period of time Idle Timeout the connection will be closed and the port will be freed and try to connect with other hosts 0 indicate disable this function Factory default
14. 0 0 65535 Seconds j A a Na _ 2 Auto Scan Alive Check 420 0 85535 Seconds collection W System Log Control Port 4001 Multilink Max Connections 1 7 Refresh Destination Host 1 192 168 10 220 2066 2 3 1 Refresh 3 Apply Only Pe Apply and Save Figure 5 13 TCP Server mode The following table describes the labels in this screen Label Description Data Port Set the port number for data transmission Auto Scan Scan the data port automatically When serial port stops data transmission for a defined period of time Idle Timeout the connection will be closed and the port will be freed and try to connect with other hosts Idle Timeout 0 indicate disable this function Factory default value is O If Multilink is configured only the first host connection is effective for this setting The serial device will send TCP alive check package in each defined time interval Alive Check to remote host to check the TCP connection If the TCP connection is not Alive Check alive the connection will be closed and the port will be freed 0 indicate disable this function Factory default is 0 The number of Max connection can support simultaneous connections are 5 default Max Connection values is 1 Table 5 9 TCP Server mode 31 Antaira Technologies STE 604C User s Manual antaira Service Mode TCP Client Mode In TCP Client Mode device
15. Antara Industrial Device Server STE 604C STE 604C P User s Manual Version 1 0 entaira www antaira com Table of Content GETTING TO KNOW YOUR DEVICE SERVER nnuuununuununnunnnnnnnnnnunnnnnnnnnnunnnnnnnnnannnnnnnnnnnnnnn nana nnmnnn nnmnnn nnn 1 1 1 About the STE 604C Serial Device Server sis 1 1 2 Software Features us os IA dere Se A cee eee ida 2 1 3 ES A a nie 2 HARDWARE INSTALLATION ui is 3 2 1 Install STE 6046 on DIN Ra ill 3 3 8 a 3 2 1 1 Mount STE 6046 0n DIN R ll 4 2 3 02 datar dt da 3 2 2 Wall Mounting Installation 22 2 22 12a era 4 2 2 1 Mount STE 604G on wall 2 ee a ia Alone at 5 HARDWARE OVERVIEW coccion dla 8 3 1 Front Panel nie NE fe rn IO gaa etnies eto 8 3 2 Front Panels EDS iaa 9 3 3 Serial POS ici Rai AA AA AA rien 10 3 4 Bottom Panel tn ne Bae eas paa 11 3 5 Rear Panel een tal nn 12 A een A re mure sn nee encres ae 13 4 1 Ethernet Cables sinon A Men ant Min ont ei 13 MANAGEMENT INTERFACE coonccccccccccacacacacncncacaca cnn 15 5 1 DS lt TOOIL HS Se a mue io Wa I O sees LU ee a bol ii da dla 15 5 1 1 A O 15 54152 Using DS Togliani es AAA eee 17 5 1 2 1 Explore device Servers cic aii aaa en 17 5 1 2 2 Gonfigure device Servers cies siete ached ment 18 5 1 2 3 G nfigure serial Boll 42 2 kein eli 27 5 2 Configuration by Web Browser iii 37 5 2 1 Connect to the Web page une een ai ea nee 37 5 2 1 1 SV SUSI ss sire 6 D Homann a 39 5 2 1 2 Port Se
16. TS changed computer and DCE can proceed A notification will be sent In TCP Server Mode when the device accepts an incoming TCP connection this event will be trigger In TCP Client Mode when the device has connected to the remote host Port connected this event will be trigger In Virtual COM Mode Virtual COM is ready to use A notification will be sent In TCP Server Client Mode when the device lost the TCP link this event will be trigger Port disconnected In Virtual COM Mode When Virtual COM is not available this event will be trigger A notification will be sent Table 5 11 Notification Antaira Technologies 36 antaira STE 604C User s Manual 5 2 Configuration by Web Browser 5 2 1 CONNECT TO THE WEB PAGE Step 1 Input the IP address of DS with http 192 168 10 2 in the Address input box of IE Step 2 Input the name and password then click OK Connect to 192 168 10 2 The server 192 168 10 2 at cgi bin requires a username and password Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection User name admin Password Remember my password Figure 5 17 Certificate Only if password is set Step 3 The system information will be shown as below 37 Antaira Technologies STE 604C User s Manual antaira 192 168 10 2 00 1E 94 5E 00 1E 1 03 Figur
17. Y port YCOM List HE Setup Wizard H IP Collection System Log 29 STE 604C User s Manual Service Mode Virtual COM Mode In Virtual COM Mode The driver establishes a transparent connection between host and serial device by mapping the Port of the serial server serial port to local COM port on the host computer Virtual COM Mode also supports up to 5 simultaneous connections so that multiple hosts can send or receive data by the same serial device at the same time Serial Settings Service Mode Notification port Service Mode Virtual COM Mode Virtual COM Mode Virtual COM Settings Misc Idle Timeout 0 0 65535 Seconds Data Port 4000 Edit IP Port Number Corea Fav HOOT de Man Vitual COM Alive Check 420 0 65535 Seconds Multilink Max Connections OO a Destination Host VCOM Name 192 168 10 220 Mapped by Other Site 2 1 Refresh Figure 5 13 Virtual COM Antaira Technologies STE 604C User s Manual antaira Label The following table describes the labels in this screen Description Map Virtual COM Max Connection Select a Virtual COM Name to map on The number of Max connection can support simultaneous connections are 5 default values is 1 When serial port stops data transmission for a defined period of time Idle Timeout the connection will be closed and the port will be freed and try to connect with other hosts 0
18. ail U SNMP Trap Software Reset Warm Start O SMTP Mail U SNMP Trap Login Failed O SMTP Mail SNMP Trap _1P Address Changed O SMTP Mail U SNMP Trap Password Changed O SMTP Mail U SNMP Trap Access IP Blocked O SMTP Mail C SNMP Trap Redundant Power Changed O SMTP Mail SNMP Trap Redundant Ethernet Changed O SMTP Mail SNMP Trap Port Event Notification Port1 y DCD changed O SMTP Mail SNMP Trap DSR Changed O SMTP Mail C SNMP Trap RE Changed O SMTP Mail C SNMP Trap CTS Changed O SMTP Mail SNMP Trap Port Connected O SMTP Mail SNMP Trap LSS SSS aaa Figure 5 28 SMTP SNMP conf The following table describes the labels in this screen antaira The events can be Syslog Syslog Syslog Syslog Syslog Syslog Syslog Gi oo Syslog Syslog Syslog Syslog Syslog ajaja jaja Syslog Label Description Hardware Reset Cold Start This refers to starting the system from power off contrast this with warm start performing a cold start DS will automatically issue an Auto warning message by sending E mail log information or an SNMP trap after booting When Software Reset Warm Start This refers to restart the computer without turning the power off When performing a warm start DS will automatically send an E mail log information or SNMP trap after reboot Antaira Technologies 56 antaira Login Failed STE 604C
19. al Management Interface 5 1 DS Tool DS Tool is a powerful Windows utility for DS series It supports device discovery device configuration group setup group firmware update monitoring functions etc It is easy for you to install and configure devices over the network 5 1 1 Install DS Tool Step 1 Execute the Setup program click start after selecting the folder for DS Tool 32 nstalling DS Tool Destination Directory C Program Files DST ool Required 8175 K Available 14362104 K Browse Figure 5 1 15 Antaira Technologies STE 604C User s Manual antaira Step 2 When installation complete successfully then click OK Sel Installing DS100 Installation was completed successfully 100 Figure 5 2 Step 3 Check for your selection The installation of DS tool is finished Launch DSTool Later Figure 5 3 Antaira Technologies 16 antaira STE 604C User s Manual 5 1 2 Using DS Tool 5 1 2 1 Explore device servers DS Tool will broadcast to the network and search all available DS devices in the network The default IP address of device is 192 168 10 2 and selects the searching device you wish to use and press Add button You can set static IP address or in DHCP client mode to get IP address automatically Finally click OK button to add the device ll gt Sm Ml H i D5 Tod e MAC 00 44 BB CC DD 77 Device List MR 4 VCOM List PIECE C
20. al Service Mode TCP Server Mode In TCP Server Mode DS is configured with a unique Port combination on a TCP IP network In this case DS waits passively to be contacted by the device After the device establishes a connection with the serial device it can then proceed with data transmission TCP Server mode also supports up to 5 simultaneous connections so that multiple device can receive data from the same serial device at the same time Port1 y TCP Server Mode y 4000 0 65535 seconds 420 0 65535 seconds 11 y max connection 1 5 Figure 5 23 TCP Server Mode 49 Antaira Technologies STE 604C User s Manual antaira The following table describes the labels in this screen Label Description TCP Server Port Set the port number for data transmission When serial port stops data transmission for a defined period of time Idle Timeout the connection will be closed and the port will be freed and try to connect with other hosts 0 Idle Timeout indicate disable this function Factory default value is 0 If Multilink is configured only the first host connection is effective for this setting The serial device will send TCP alive check package in each defined time interval Alive Check to remote host to check the TCP connection If the TCP connection is not alive Alive Check the connection will be closed and the port will be freed 0 indicate disable this function Factory default i
21. anage STE 604C inside or outside the NAT router It is easy for different IP domain users to use STE 604C Therefore STE 604C is the best communication redundant solution for current application of serial devices 1 Antaira Technologies STE 604C User s Manual antaira 1 2 1 3 Software Features Redundant Dual Ethernet Ports Recovery time lt 10ms Switch Mode Supported Daisy Chain support to reduce usage of switch ports NAT pass through User can manage STE 604C through NAT router Redundant Power Inputs 12 48VDC on terminal block Redundant multiple host devices 5 simultaneous in Virtual COM TCP Server TCP Client mode UDP Management by HTTP and Telnet Versatile Modes Virtual Com Serial Tunnel TCP Server TCP Client UDP Event Warning by Syslog Email SNMP trap Relay and Beeper Various Windows O S supported Windows NT 2000 XP 2003 VISTA 32bits Hardware Features Redundant Power Inputs 12 48 VDC on terminal block and power jack Operating Temperature 30 to 70 C Storage Temperature 40 to 85 C Operating Humidity 5 to 95 non condensing Casing IP 30 2 10 100Base T X Ethernet port 1 optional P O E PD port Dimensions W x D x H 52 mm W x 106 mm D x 144 mm H Antaira Technologies 2 antaira STE 604C User s Manual Hardware Installation 2 1 Install STE 604C on DIN Rail Each STE 604C has a Din Rail kit on rear panel The Din Rail kit helps STE 604C to fix on the Din Rail Itis eas
22. by mapping the Port of the serial server serial port to local COM port on the host computer Virtual COM Mode also supports up to 5 simultaneous connections so that multiple hosts can send or receive data by the same serial device at the same time Port1 y Virtual COM Mode y 0 0 65535 seconds 420 0 65535 seconds 11 y max connection 15 Figure 5 22 Virtual COM mode 47 Antaira Technologies STE 604C User s Manual antaira The following table describes the labels in this screen Label Description When serial port stops data transmission for a defined period of time Idle Timeout the connection will be closed and the port will be freed and try to connect with other hosts Idle Timeout 0 indicate disable this function Factory default value is O If Multilink is configured only the first host connection is effective for this setting The serial device will send TCP alive check package in each defined time interval Alive Check to remote host to check the TCP connection If the TCP connection is not Alive Check alive the connection will be closed and the port will be freed 0 indicate disable this function Factory default is 0 The number of Max connection can support simultaneous connections are 5 default Max Connection values is 1 Table 5 16 Virtual COM mode Not allowed to mapping Virtual COM from web Antaira Technologies 48 antaira STE 604C User s Manu
23. d I Access IP Blocked iz Redundant Power Changed Power 1 Fault Redundant Ethernet Changed Power 2 Fault r r r r r r System Log Settings Server IP Port The following 1 Refresh 19 Retesh jo Using Current Host s Log Server Eth 1 Link Down T Eth 2 Link Down General Security Networking Notification Management Upgrade Firmware Save Load Syslog Notificatioy Fault LED Relay 3 Apply Only E Apply and Save Figure 5 8 Notification table describes the labels in this screen Label Description SNMP Trap To notify events by SNMP trap Email Notification Syslog Notification To notify events by Email To notify events by Syslog Notify items Events to be notified Apply Apply and Save Apply current setting Apply and save current setting 23 Table 5 3 Notification Antaira Technologies STE 604C User s Manual Management File Device Configuration Ca Al Broadcast Device a Device gy Options Help veom Device Firmware Wizard Wizard Wizard sig sig Se Wizard Pig Sas hz M DSTool Device List 192 168 10 2 Y port Y potz Y porta Y port a VCOM List 5 Setup Wizard d IP Collection YY System Log General Security Networking Notification Management Upgrade Firmware Save Load lv Web Management Enable Goto Web Management IV Telnet
24. e 5 18 System information Antaira Technologies 38 antaira STE 604C User s Manual 5 2 1 1 System Time SNTP STE 604C OEnable Disable GMT 08 00 Pacific Time US amp Canada Tijuana E Wed Dec 31 16 13 18 PST 1969 pool ntp org Port 123 Console OEnable Disable Figure 5 19 Time SNTP The following table describes the labels in this screen Label Description Name You can set the name of DS SNTP Enable the SNTP server Time zone After you set the SNTP enable select the time zone you located Time server Input SNTP server domain name or IP address and Port Telnet Console SSH is included for security reasons In some cases you may need Console to disable this function to prevent unauthorized access from internet The factory default is enable Table 5 12 Time SNTP 39 Antaira Technologies STE 604C User s Manual antaira IP Configuration You must assign a valid IP address for DS before attached in your network environment Your network administrator should provide you with the IP address and related settings The IP address must be unique and within the network otherwise DS will not have a valid connection to the network You can choose from three possible IP configuration modes Static DHCP BOOTP The Factory Default IP address is 192 168 10 2 Static y 192 168 10 2 255 255 255 0 192 168 10 1 192 168 10 1
25. ect to any other network device PCs servers switches routers or hubs Please refer to the following table for cable specifications Cable Type Max Length Connector 10BASE T Cat 3 4 5 100 ohm UTP 100 m 328 ft RJ 45 100BASE TX Cat 5 100 ohm UTP UTP 100 m 328 ft RJ 45 Table 4 1 Cable Types and Specifications 100BASE TX 10BASE T Pin Assignments With 100BASE TX 10BASE T cable pins 1 and 2 are used for transmitting data and pins 3 and 6 are used for receiving data 13 Antaira Technologies antaira STE 604C User s Manual Pin Number Assignment 1 TD TD RD Not used Not used RD Not used M oa BR D Not used Table 4 2 RJ 45 Pin Assignments The STE 604C supports auto MDI MDI X operation You can use a straight through cable to connect PC to STE 604C The following table below shows the 10BASE T 100BASE TX MDI and MDI X port pin outs Pin Number MDI port MDI X port 1 TD transmit RD receive 2 TD transmit RD receive 3 RD receive TD transmit 4 Not used Not used 5 Not used Not used 6 RD receive TD transmit 7 Not used Not used 8 Not used Not used Antaira Technologies Table 4 2 MDI MDI X pins assignment Note and signs represent the polarity of the wires that make up each wire pair 14 antaira STE 604C User s Manu
26. figuration by Telnet 5 3 1 Connect to DS You can use Telnet to access and configure the unit cs Telnet 192 168 10 2 STE 684C 192 168 18 2 Password login admin o www ANTAIRA Industrial Serial Device Server DD DC al D DE DE Det Det DD DD DD DE De Det Det DE DE Det DD DD DE DE DD DD Commander Ss jord Re Input Starting Main Menu ANTAIRA Industrial Serial Device Server Commander Overview General Settings Network Settings Ports setting Security lt Ac Notificatio Change Password Load Factory Default Save configuration Reboot Exit amp Logout ible IP gt Settings to Warning Settings elect one function 8 9 C L S R Q STE 604C User s Manual The Telnet interface is shown below Figure 5 30 Telnet 59 Antaira Technologies STE 604C User s Manual antaira Technical Specifications Network Interface 2x 10 100Base T X which support Redundant Dual Ethernet or Ethernet Switch Mode support Auto recover less than 10ms connector RJ 45 Protection Built in1 5KV magnetic isolation ICMP IP TCP UDP DHCP BOOTP ARP RARP DNS SNMP Protocols MIB Il HTTPS SSH Serial Interface Interface 4x RS232 RS422 4 2 Wire RS485 Which can be configured by DS Tool Connector Male DB9 Serial Baud Rate 110 bps to 460 8 Kbps Data Bits 5 6 7 8 Parity odd even none mark space Stop Bits 1 1 5 2 RS 232 signal
27. he PWR2 links the green LED will be light on 3 LED for fault indicator When fault occurred this red LED will be light on 4 LED for Serial ports status When data transmitted the green LED will be light on When data received the red LED will be light on 5 LED of 10Base T connection on Ethernet port Antaira Technologies 8 antaira 6 10 100Base T X Ethernet port STE 604C User s Manual 7 LED of 100Base TX connection on Ethernet port 8 RS 232 422 485 serial port Mode configured by DS Tool 3 2 Front Panel LEDS The following table describes the labels that stick on the STE 604C LED Color Status Description On Power supplied over Ethernet Cable P O E Green Red Indicates and IP conflict or DHCP or BOOTP Red Blinking server did not respond properly On DC power 1 activated PWR1 Green Red Red blinkin Indicates an IP conflict or DHCP or BOOTP 9 server did not respond properly On DC power 2 activated PWR2 Green Red Red blinkin Indicates an IP conflict or DHCP or BOOTP 9 server did not respond properly Fault Red On Fault event occurred Green Blinking Serial port is transmitting data S1 S4 Red Blinking Serial port is receiving data Green On Blinking 100Mbps LNK ACT ETH1 Green Amber Amber On Blinking 10Mbps LNK ACT Green On Blinking 100Mbps LNK ACT ETH2 Green Amber Amber On Blinking 10Mbps LNK ACT Antaira Technologies antaira
28. heck the TCP connection If the TCP connection is not alive Alive Check the connection will be closed and the port will be freed 0 indicate disable this function Factory default is 0 Connect on Startup The TCP Client will build TCP connection once the connected serial device is started Connect on Any The TCP Client will build TCP connection once the connected serial device starts to send Character data Table 5 18 TCP client mode Antaira Technologies 52 antaira STE 604C User s Manual Service Mode UDP Client Mode Compared to TCP communication UDP is faster and more efficient In UDP mode you can Uni cast or Multi cast data from the serial device server to host computers and the serial device can also receive data from one or multiple host f Port1 y UDP Mode e 4000 Figure 5 25 UDP client mode 53 Antaira Technologies STE 604C User s Manual antaira 5 2 1 3 Management Access IP Control Access IP Control Settings allow you to add or block the remote host IP addresses to prevent unauthorized access If host s IP address is in the accessible IP table then the host will be allowed to access the DS You can choose one of the following cases by setting the parameter 1 Only one host with a special IP address can access the device server IP address 255 255 255 255 e g 192 168 0 1 255 255 255 255 2
29. iption Using DHCP BOOTP IP Address automatically assigned by a DHCP server in your network Static IP Address Manually assigning an IP address All devices on the network must have the same subnet mask to communicate on the Subnet Mask network Gateway Enter the IP address of the router in you network Enter the IP address of the DNS server The DNS server translates domain names into DNS Server IP address Redundant When the connection between master link and LAN fails the DS can automatically switch to another LAN port within10mS and still guarantees a non stop connection Switch Mode Switch Daisy Chain support to reduce usage of switch ports Table 5 3 Network setting Antaira Technologies 22 antaira STE 604C User s Manual Notification Specify the events that should be notified to the administrator The events can be alarmed by E mail SNMP trap or system log gt DSTool Eile Device Configuration A ka gal Broadcast Device p Device ma Options Help vcom Device Firmware Wizard Wizard Wizard N E sie apy Wizard Pig a ER uz DSTool Device List 192 168 10 2 Y port Y port2 Y porta Y port Gs VCOM List 52 Setup Wizard d IP Collection YY System Log SNMP Trap Email Notification Syslog Setttings Notified Items Hardware Reset Cold Start Software Reset warm Start Login Failed IP Changed Password Change
30. l be sent Port disconnected In TCP Server Client Mode when the device lost the TCP link this event will be trigger In Virtual COM Mode When Virtual COM is not available this event will be trigger A notification will be sent Power 1 Fault When Power 1 Fault a notification will be sent and the Fault LED will be lighted Power 2 Fault When Power 2 Fault a notification will be sent and Fault LED will be lighted Eth1 link down When Eth1 link down a notification will be sent and Fault LED will be lighted Eth2 link down When Eth2 link down a notification will be sent and Fault LED will be lighted 57 Table 5 19 System event conf Antaira Technologies STE 604C User s Manual antaira 5 2 1 4 Save Reboot Figure 5 29 Save Reboot The following table describes the labels in this screen Label Description Load default configuration except settings of Network If you want load all factory default Factory Default you should press Reset button about the five seconds on the device Hardware restore Restore Restore the previous exported configuration Configuration Backup Export the current configuration to a file Configuration Upgrade Firmware Upgrade to a new firmware with specified file Reboot Device Reboot the device server warm start Table 5 20 Save Reboot Antaira Technologies 58 antaira 5 3 Con
31. lect the Time zone By Clicking the Get current Host button you will get your local IP and then set the Set Auto IP Report Report interval time The device server will report its status periodically Table 5 1 General settings At IP collection option show the device server status The report interval is 0 indicate disable this setting default But you can set the other IP or Port Security DSTool File Device Configuration Options Help T 3 i vcom Device Firmware m on gt j Wizard Wizard Wizard ff ae ee EA Broadcast weard 9 RER ar Ml DSTool General Networking Notification Management Upgrade Firmware Save Load Device List Access IP Table Password jp 192 168 10 2 P1 Mask Enabled New Password Y portl y port2 IP2 Mask D Enabled rT Enabled Confirm New Password Y porta Y port IP3 Mask gt Entel Old Password G VCOM List IP4 Mask Enabled A FR Setup Wizard Enabled dl IP Collection IPS Mask Change Password Enabled YY System Log IPG Mask Enabled IP rsd Mask iY IP8 Hm Mask Enabled Enabled IP9 Mask IP10 Mask Enabled Enabled IP11 Mask _ id Mask Enabled Enabled IP13 Mask Mask a a ua a a le 1 Refresh Figure 5 6 Security 19 Antaira Technologies STE 604C User s Manual antaira The following table describes the labels in this screen
32. ra Save Load File Device Configuration Options Help 3 vcom Device Firmware Ta m on I Wizard Wizard Wizard pe ae e Broadcast E Bence Wizard ei ms ez M DSTool General Security Networking Notification Management Upgrade Firmware Save Load Device List 192 168 10 2 Y poti Y potz 4 port3 4 port WCOM List Load Default FR Setup Wizard IP Collection Load Default YY System Log Save Configuration to Flash Reboot Device Reboot Device Import Export Configuration Import Export 1 Refresh 2 Apply Only ae Apply and Save Figure 5 11 Save Load The following table describes the labels in this screen Label Description Save Configuration to Save current configuration into flash memory Flash Load default configuration except the network settings If you want to load all factory Load Default default you need to press Reset button on the device Hardware restore Reboot Device Reboot the device server warm start Import Configuration Restore the previous exported configuration Export Configuration Exported current configuration to a file to backup the configuration Table 5 6 Save Load Antaira Technologies 26 antaira STE 604C User s Manual 5 1 2 3 Configure serial port Serial Settings Device Firmware Wizard Wizard Serial Settings Service Mode Notification ES De
33. rial SOtting PERERFERPEEFEREPPEFFEPPEFIUTERFEEFFFEPEPEFFFEEPPEFFPEEEFHRCLEEFEIEEFEREFERFLEFEFETELEFEFFRGEFFERFEFFIEFEFN 43 5 2 1 3 Manage Mai ee AA e ENS 54 5 2 1 4 Save RebDO0lkius cucuta aii 58 antaira STE 604C User s Manual 5 3 Configuration DY Telnet voii iaa dia 59 5 3 1 Gonnectt0 DS TEHPETRPRRLSRCFFFFINFTPERIFFECFEREURFCER ENEEPEPFETLEPFEIRPELFEFFFFEEFTESFIEEFFRIECEFFERFETSEFEIEPFEFERFFSPRRFERFTEFFERFE 59 60 TECHNICAL SPECIFICATIONS antaira STE 604C User s Manual Getting to Know Your Device Server 1 1 About the STE 604C Serial Device Server STE 604C is an innovative 4 ports RS232 422 485 to 2 ports LAN device server Optional P O E PD Ethernet port on STE 604C P Model Users are able to configure STE 604C by DS Tool via LAN port STE 604C offers many powerful features for HW 8 SW redundant functions When the connection between master link and LAN fails the STE 604C can automatically switch to another LAN port within 10mS and still guarantee a non stop connection STE 604C also supports switch mode users can use Daisy Chain to reduce the usage of Ethernet switch ports Secondly the STE 604C can simultaneously transfer data into 5 host PCs This feature can assure all critical data that saved in different host PCs to avoid Ethernet break or host PCs failure Thirdly the STE 604C provides dual redundant power inputs on terminal block STE 604C also provides NAT pass through function so that users are able to m
34. rnet to Serial Latency This mode optimized for shortest response time Delimiter You can define max 4 delimiters 00 FF Hex for each way The data will be hold until the delimiters are received or the option Flush Serial to Ethernet data buffer times out 0 means disable Factory default is 0 Flush Data Buffer After The received data will be queuing in the buffer until all the delimiters are matched When the buffer is full 4K Bytes or after flush S2E data buffer timeout the data will also be sent You can set the time from 0 to 65535 seconds Delimiter You can define max 4 delimiters 00 FF Hex for each way The data will be hold until the delimiters are received or the option Flush Ethernet to Serial data buffer times out 0 means disable Factory default is 0 Flush Data Buffer After The received data will be queuing in the buffer until all the delimiters are matched When the buffer is full 4K Bytes or after flushE2S data buffer timeout the data will also be sent You can set the time from 0 to 65535 seconds Force TX Interval Time Force TX interval time is to specify the timeout when no data has been transmitted When the timeout is reached or TX buffer is full 4K Bytes the queued data will be sent O means disable Factory default value is 0 Antaira Technologies Table 5 7 Serial settings 28 antaira ES Device List E 192 168 10 2 Y portl Y port2 Y porta
35. s TxD RxD RTS CTS DTR DSR DCD RI GND RS 422 signals Tx Tx Rx Rx GND RS 485 4 wire signals RS 485 2 wire signals Tx Tx Rx Rx GND Data Data GND Flow control XON XOFF RTS CTS DTR DSR Serial Line Protection LED Indicators Built in 15KV ESD protection PWR P O E 1 2 Ready 1 Red On Power is on and booting up Red Blinking Indicates an IP conflict or DHCP or BOOTP server did not respond properly Antaira Technologies 60 antaira STE 604C User s Manual 2 Green On Power is on and functioning normally Green Blinking Located by Administrator ETH1 2 Link ACT Orange ON Blinking 10 Mbps Ethernet Green ON Blinking 100 Mbps Ethernet Serial TX RX LEDS Red Serial port is receiving data Green Serial port is transmitting data Fault Fault alarm Red Power Requirements Power Input PWR1 2 12 48VDC in 6 pin Terminal Block Reverse Polarity Protection Present at terminal block Power Consumption Software Utility 7 Watts MAX Utility DS Tool for Windows NT 2000 XP 2003 VISTA which include Device discovery Auto IP report Device setting run time change no rebooting Access control list Group setting Device monitoring Serial port monitoring Log info Group Firmware update Serial Mode Virtual Com TCP Server TCP Client UDP Serial Tunnel TCP Alive Check Timeout Inac
36. s 0 The number of Max connection can support simultaneous connections are 5 default values Max Connection is 1 Table 5 17 TCP server mode Antaira Technologies 50 antaira STE 604C User s Manual Service Mode TCP Client Mode In TCP Client Mode device can establish a TCP connection with server by the method you set Startup or any character After the data has been transferred device can disconnect automatically from the server by using the TCP alive check time or Idle timeout settings Porti y TCP Client Mode y 0 0 0 0 4000 0 65535 seconds 420 0 65535 seconds Startup O Any Character 65535 65535 65535 65535 Figure 5 24 TCP client mode 51 Antaira Technologies STE 604C User s Manual antaira The following table describes the labels in this screen Label Description Destination Host Set the IP address of host and the port number of data port When serial port stops data transmission for a defined period of time Idle Timeout the connection will be closed and the port will be freed and try to connect with other hosts 0 Idle Timeout indicate disable this function Factory default value is 0 If Multilink is configured only the first host connection is effective for this setting The serial device will send TCP alive check package in each defined time interval Alive Check to remote host to c
37. tivity Timeout Delimiter for Data Packing Force TX Timeout for Data Packing Multiple Link 5 Hosts simultaneous connection Virtual Com TCP server TCP Client UDP 61 Antaira Technologies STE 604C User s Manual VCOM Driver Windows NT 2000 XP 2003 VISTA antaira Configuration Web HTTPS console SSH console Console Command DS Tool for Windows NT 2000 XP VISTA Environmental Operating Temperature 30 to 70 C 22 to 158 F Operating Humidity 5 to 95 Non condensing Storage Temperature 40 to 85 C 40 to 185 F Mechanical Dimensions W x D x H 52mm W x106mm D x144mm H Casing IP 30 protection Regulatory Approvals IEC 60068 2 27 Shock Free Fall IEC 60068 2 32 Vibration IEC 60068 2 6 EMI FCC Part 15 CISPR EN55022 class A EN61000 4 2 ESD EN61000 4 3 RS EN61000 4 4 EFT EMS EN61000 4 5 Surge EN61000 4 6 CS Warranty 5 years Antaira Technologies 62
38. vice List portl 192 168 10 2 Port Alias Port Y port2 Y port3 Baudrate 38400 al Stop Bits Fr Performance Throughput al de el Party No e FlowContiol No Fow y F4 Setup Wizard Data Bits g y Interface n5232 A d IP Collection APP YY System Log Delimiter Settings Serial to Ethernet Ethemet to Serial Delimiter 1 Delimiter 2 Delimiter 3 m Delimiter 4 fo HEX fo HEX fo HEX HEX F Enabled F Enabled F Enabled Enabled Flush Ethernet to Serial Data Buffer After je 0 65535 ms The received data will be queueing in the buffer until all the delimiters are matched When the buffer is full 4K Bytes or after flush E25 data buffer timeout the data will also be sent Force TX interval time a Apply and Saye Figure 5 12 Serial Settings 27 Antaira Technologies STE 604C User s Manual antaira The following table describes the labels in this screen Label Description Port Alias Remark the port to hint the connected device Interface RS232 RS422 RS485 2 wires RS485 4 wires 110bps 300bps 1200bps 2400bps 4800bps 9600bps 19200bps oo 38400bps 57600bps 115200bps 230400bps 460800bps Data Bits 5 6 7 8 Stop Bits 1 2 1 5 Parity No Even Odd Mark Space Flow Control No XON XOFF RTS CTS DTR DSR Throughput This mode optimized for highest transmission speed Performance Serial to Ethernet Ethe
39. y to install the STE 604C on the Din Rail 2 1 1 Mount STE 604C on DIN Rail Step 1 Slant the STE 604C and mount the metal spring to Din Rail T Metal Spring Figure 2 1 3 Antaira Technologies STE 604C User s Manual antaira Step 2 Push the STE 604C toward the Din Rail until you heard a click sound Figure 2 2 2 2 Wall Mounting Installation Each STE 604C has another installation method for you A wall mount panel can be found in the package The following steps show how to mount the STE 604C on the wall Antaira Technologies 4 antaira STE 604C User s Manual 2 2 1 Mount STE 604C on wall Step 1 Remove Din Rail kit Figure 2 3 5 Antaira Technologies STE 604C User s Manual antaira Step 2 Use 6 screws that can be found in the package to combine the wall mount panel Just like the picture shows below Figure 2 4 The screws specification shows in the following two pictures In order to prevent STE 604C from any damage the size of screws should not be larger than the size that used in STE 604C Pozidrive Figure 2 5 Antaira Technologies 6 antaira STE 604C User s Manual Step 3 Mount the combined STE 604C on the wall Figure 2 6 7 Antaira Technologies STE 604C User s Manual entaira Hardware Overview 3 1 Front Panel Figure 3 1 1 LED for PWR1 and system status When the PWR1 links the green LED will be light on 2 LED for PWR2 and system status When t
Download Pdf Manuals
Related Search