Handleiding CopyBox 7 USB
Contents
1. ReScan Bus searches for the connected USB pen drives If the controller does not automatically identify the USB pen drive the drive can be scanned and identified again through this function Press ENT to enter the next figure The default is Off Press Y to select On Press ENT The following message will be displayed on the LCD The number of the connected devices will be shown in the LCD If the device remains unfound after rescanning please check the device for defects or check the list of compatible devices on the manufacturer website 7 Source Size The function Source Size shows the disk capacity of the source USB pen drive A y Page 8 of 19 2009 Virtual Vision 7 User Manual CopyBox 7 USB Duplicator Operational Functions 8 Select Source Function 8 Select Source is to identify and assign source drives Select function 8 9 Image Function 9 Image is only usable under Stand Alone mode when a HDD is connected This function includes 8 subfunctions Load Delete Image Image Info Compare Image Select Image Select Src Drive Image Format Info and Edit The loaded data is called an image file Select function 9 9 1 Select Image This function is to select a partition in the hard disk First select the function by pressing Y After installing a hard disk your copy controller will format it automatically Each partition occupies 5GB The number of partitions is dependent on the2. The Compare function compares the data in the source USB pen drive with that in the target USB pen drive after the copying operation finishes Choose the third function Compare Please insert the source and target USB pen drives Upon completion of data comparing the following results will be displayed on the LCD and the LED of the target USB port will turn orange and stay lit 4 Async Compare The function Async Compare adds an extra target drive for data comparing during the comparing operation Choose the fourth function Async Compare and insert the source and target USB pen drives to the corresponding USB ports During the process you can insert another target USB pen drive for the Async Compare operation The comparing rate will change accordingly The blinking green USD LED on the CopyBox panel shows that the comparing is in progress When the LED turns orange and stay lit the data comparing of the USB pen drive on that USB port is completed Upon completion the following message is displayed on the LCD 5 PreScan The function PreScan scans and tests the readability of the source USB pen drive Choose the fifth function PreScan and insert the source USB pen drive X yaa Page 7 of 19 2009 Virtual Vision User Manual CopyBox 7 USB Duplicator Operational Functions Press ENT The following message will be displayed on the LCD 6 ReScan Bus The function
3. hard disk s capacity The partitions are alphabetically arranged Select a partition by pressing A Y and LCD will show the message as follows 9 2 Image Info This function is to show the basic information of an image file stored in a particular partition First select the function by pressing Y X yaa Page 9 of 19 2009 Virtual Vision User Manual CopyBox 7 USB Duplicator Operational Functions 9 3 Load Now press ENT and you will enter the following figure Here the function Load is to let you load data from USB into the current partition of the hard disk P A means partition A 9 4 Compare Image This function is to compare the contents of the source DVD and those of the image file in the partition First select the function by pressing Y When comparison is successfully LCD will show the results as follows 9 5 Delete Image If you want to delete an image file stored in a particular partition you can use the function Delete Image to do so First select the function by pressing V A y Page 10 of 19 2009 Virtual Vision 7 User Manual CopyBox 7 USB Duplicator Operational Functions 9 6 Rename Image This function is to rename the image file First select the function by pressing V After the image file is successfully renamed LCD will show the results as follows 9 7 HDD Usage This function is to check the capacity of the HDD First select the function by
4. CopyBox USB Duplicator User Manual User Manual CopyBox 7 USB Duplicator Table of Contents A y Page 2 of 19 2009 Virtual Vision User Manual CopyBox 7 USB Duplicator Table of Contents Table of Contents Table DECO ari aa dae airada aa 3 OV SL VIS Wisin iaa 4 AS NN 4 BUR ons ond LED ias 4 Operational FUNCION cnn ii 5 Vi CODY siria iia 6 ASA GE COPY aaen an a E EERE E NE E E E 6 Dees OF MAL E E EE Licei 7 ACASO COMP ONS 5 aa a 7 PESCON aee RN 7 CROS CON BUS oenina eE E EEEE E EE EEE E EE 8 Ty SOUCO SKE iii A N a staccato eee 8 8 SEISCTSOUICE O E a a aa aa a a aaa a a a a E dada a a aa at 9 imagen La 9 9 l seleciimage a aaa iaia iaia 9 92 Image lO iii iii ibas 9 o RN 10 D A COMP GNIS incitan aaa aan E ii 10 2 5 Delete IMAGE AA ARR RIA RARI IAA ATA AIAR AIA ATRIA 10 9 6 RENGMEAMAGS inline in abano aan alan AAA 11 9 7 DD Us ade iii lil ii ed 11 O ADD BONING sormeaan aLaaa ie ALA sad 1 IO SSM Pasti O NA 12 TOPO G UGG csceas eves cede O cia 12 ARA CN 12 TOS SIAMU MENU iii aaa adas jaa des toads Genii 12 OL AUTO COMP OC ia dani 13 TOSS BUMOAMSOUN Gis scsseecsesessiesesescetsepesedesceeseesseces acaacaeanesdesesecaacdeaeesdecesecauceeaededeseiedsachsanesdeaeaecaacaeaeesieseiacsschaseadsenaseeas 13 IOG B T 54 eer a aaa aia 13 TOTO a A soleil A ala 14 108 FAST COPY iii ia e lion dalla Md det dons id loves dl en lia aaa 14 TOLD AUTO a da isis 14 10 10 AUTO Siam ias 15 M AdVAncSdO SOU uni LIL La LL LL
5. Lana Liana 15 TI Updafe Finmware a ias 15 Il 2Compare FMmware siglata aaa aaa aaa 15 ISA WDIGgnosie ana 16 TLA Lood Dra iii ea ea nani ea ana e ai 16 TroubleShootingl siria aaa aa aaa aa Raa AAR 17 EEIN ENI e EA AEEA E IAA EEA i e 18 Y yaa Page 3 of 19 2009 Virtual Vision User Manual CopyBox 7 USB Duplicator Overview Overview The CopyBox 7 USB is a standalone USB stick data backup system which supports Hi Speed USB USB 2 0 pen drives Users can easily and instantly back up their pen drives through the LCD panel and keys on this system without connecting their pen drives to computers This system supports most mainstream USB pen drives and is perfect for data backup and small scale production in households common offices and small businesses Features Standalone USB to USB pen drive data backup controller Independent copy controller without the need of additional hardware or software Supporting one internal 3 5 inch SATA hard drive Supporting one to many data backup of Hi Speed USB pen drives Instant backup of important data from the pen drives LCD User friendly interfaces and the message will be displayed on the LCD Updating firmware via a USB pen drive Buttons and LCD There are four buttons and an LCD on the panel of the CopyBox 7 USB LCD display Displays all functions and messages A ENT vV Esc Selection Button Up Selection Button Enter Scroll up the function list or the menu Ex
6. anges system status It includes 4 sub functions Update Firmware Compare Firmware H W Diagnostic and Load Default Please refer the figure on Page 14 for other information 11 1 Update Firmware Now press ESC and Y to enter the following menu This function updates the firmware to the latest version But you have to download the latest firmware first You can ask your supplier for the latest firmware by email or directly download the latest firmware from the website Extract the zip file to a blank pen drive You don t have to extract the file if it is a bin file Insert the pen drive to the source USB port and press ENT The system will start searching for the new firmware as shown in the following figure Next press ENT to start updating the firmware Upon completion the system will reboot itself automatically 11 2 Compare Firmware Now press ESC and Y to enter the following menu This function compares the current version of firmware and the newly download firmware It verifies whether the download version is the latest y Page 15 of 19 2009 Virtual Vision User Manual CopyBox 7 USB Duplicator Operational Functions Next press ENT to start comparing the firmware as shown in the following figure You can upgrade the firmware after the comparing confirms that it is the latest 11 3 H W Diagnostic Press ESC and Y to enter the following menu This function tests the system Press ESC and Y to ent
7. arget Drive Space Not Enough PreScan Fail Save new config Fail Load Default Config Preparing Check Target Please Await Identical Hold ESC to Exit Initializes the system SDRAM Detects the USB pen drives connected to the system Aborting the operation in progress Analyzes the source USB pen drive The source USB pen drive is not inserted or unable to identify The target USB pen drive is not inserted or unable to identify The Hard Disk do not have image file The image file can not be read or read error from Hard Disk The source USB pen drive can not be read or read error The target USB pen drive can not be read or read error The target USB pen drive can not be written or write error The target USB pen drive space is too small The PreScan of the source USB pen drive fails Saving the new configuration fails Load the default configuration or not The system is preparing itself for data copying The system is checking the target device now The two copies of data for comparison are identical Hold down ESC for about 1 second to terminate the test Page 18 of 19 X E 2009 Virtual Vision f User Manual CopyBox 7 USB Duplicator LCD Messages X ya Page 19 of 19 2009 Virtual Vision 7
8. drive is inserted and the target USB pen drive has a disk space equal to or larger than the source drive Choose the first function Copy Insert the source pen drive to the source USB port and a blank pen drive to the target USB port 8 Shows the number of detected pen drives including the source and target pen drives Press ENT to start copying data The following message will be displayed on the LCD and the green LED on the CopyBox panel will blinks In the figure the data volume and the copy time decrease while the completed percentage increases Upon completion of data copying the following message will be displayed on the LCD and the LED indicator of the USB port that has successfully completed the copying operation will turn orange and stay lit 2 Async Copy The function Async Copy adds an extra target drive during the copying operation Choose the second function Async Copy During the process you can insert another USB pen drive as the target of the Async Copy operation The copying parameters will change accordingly The blinking green USD LED on the CopyBox panel shows that the copying is in progress When the LED turns orange and stay lit the data copying of the USB pen drive on that USB port is completed Upon completion the following message is displayed on the LCD X re Page 6 of 19 2009 Virtual Vision 7 User Manual CopyBox 7 USB Duplicator Operational Functions 3 Compare
9. ecute the selected function A ENT Selection Button Down Selection Button Escape Scroll down the function list or the menu Abort the selected function v ESC X re Page 4 of 19 2009 Virtual Vision 7 User Manual CopyBox 7 USB Duplicator Operational Functions Operational Functions The copy controller has 11 functions in total 8 sub functions under the ninth function 10 sub functions under the tenth function and 4 sub functions under the eleventh function These functions are listed below Copy Compare PreScan WOON A 0O0AO0N Image 9 01 9 02 9 03 9 04 9 05 9 06 9 07 9 08 10 Setup 10 01 10 02 10 03 10 04 10 05 10 06 10 07 10 08 10 09 10 10 11 Adv Setu 11 01 11 02 11 03 11 04 Async Copy Async Compare ReScan BUS Source Size Select Source Select Image Image Info Load Compare Image Delete Image Rename Image HDD Usage HDD Format Language Copy Size Startup Menu Auto Compare Button Sound Device Info System Info Fast Copy Auto Start Auto Start Timer p Update Firmware Compare Firmware H W Diagnostic Load Default Page 5 of 19 Y ya 2009 Virtual Vision User Manual CopyBox 7 USB Duplicator Operational Functions 1 Copy The Copy function copies directly the data of the source USB pen drive to a blank USB pen drive Before copying please make sure that the source USB pen
10. er the following menu The system first tests the LCD and next the buttons Subsequently the system carries out the RAM self test hardware connection test and flash memory test All the test results are displayed on the LCD This is most easy and simple way to check whether the system functions normally Upon completion of the entire process the following message will be displayed on the LCD 11 4 Load Default Now press ESC and Y to enter the following menu This function restores all the settings to the default values Load Default Press ENT and to enter the following menu Confirm restoring to the default values by pressing A or Y Load Default A y Page 16 of 19 2009 Virtual Vision 7 User Manual CopyBox 7 USB Duplicator Troubleshooting Troubleshooting The LCD If nothing shows up on the LCD after system starts please ensure the power cable is firmly connected and the sockets work normally The Error Messages If a user stops the copying process by pressing ESC an error message will be displayed on the LCD Interruption of the copying process may freeze the system and rebooting the system is necessary If the USB pen drive is unreadable an error message will appear on the LCD Please get another USB pen drive and try again If the copy controller does not detect any device after it initializes an error message will be displayed on the LCD Compatibility of USB pen drives You can download
11. owing menu This function allows you to choose any function except Advance Setup as the first item on the menu every time the system starts Press ENT to enter the following menu The default setting is Copy You can choose any other function as the first item Remember to save the new setting by pressing ENT A y Page 12 of 19 2009 Virtual Vision 7 User Manual CopyBox 7 USB Duplicator Operational Functions 10 4 Auto Compare In the above menu press ESC and Y to enter the following menu This function automatically compares the source pen drive and the target pen drive after copying Press ENT to enter the following menu The default setting is Off You can change itto On by pressing VW 10 5 Button Sound Now press ESC and Y to enter the following menu This function controls the sound of the button when it is pressed Press ENT to enter the following menu The default setting is On You can change it to Off by pressing V 10 6 Device Info Now press ESC and Y to enter the following menu This function shows the information of the source and target USB pen drives connected to the controller You can browse the device information of the devices plugged to all the ports with the buttons 4 and Y or enter the following menu to check the version information of the USB pen drive by pressing ENT VW Page 13 of 19 2009 Virtual Vision User Manual CopyB
12. ox 7 USB Duplicator Operational Functions 10 7 System Info Now press ESC and Y to enter the following menu This function shows the system information Press ENT to enter the following menu Press ENT to enter the following menu Press ESC to exit the menu when you finish 10 8 Fast Copy Now press ESC and Y to enter the following menu This function is fast data copying It supports FAT and FAT32 file formats Press ENT to enter the following menu The default setting is On You can change it to Off by pressing V 10 9 Auto Start Now press ESC and Y to enter the following menu This function enables automatic data copying It has to be used together with the 9 10 function for automatic data copying Press ENT to enter the following menu The default setting is Off You can change it to 1 8 by pressing Y according to the number of connected devices A y Page 14 of 19 2009 Virtual Vision 7 User Manual CopyBox 7 USB Duplicator Operational Functions 10 10 Auto Start Timer Now press ESC and Y to enter the following menu This function sets the start time of the automatic copying which is related to the 10 09 function If the 10 09 function is off the 10 10 function is ineffective too Press ENT to enter the following menu The default setting is Off You can change it to 50s 5s by pressing VW 11 Advanced Setup The function Adv Setup ch
13. pressing V 9 8 HDD Format This function is to see how you have formatted your hard disk Now press ESC and Y to enter the following figure VW Page 11 of 19 2009 Virtual Vision User Manual CopyBox 7 USB Duplicator Operational Functions 10 Setup The function Setup changes the default settings Once the settings are changed they have to be saved by pressing ENT However the default settings are recommended for best performances This function has 10 sub functions including Language Copy Size Startup Menu Auto Compare Button Sound Device Info System Info Fast Copy Auto Start and Auto Start Timer Please refer to the figure in Page 14 for detailed information Choose the eighth function Setup as shown in the following figure 10 1 Language Now press ENT to enter the following menu This function can specify the language of the LCD messages Press ENT to enter the following menu The default setting is English You can change the display language to Spanish Japanese Traditional Chinese and Simplified Chinese 10 2 Copy Size Now press ESC and Y to enter the following menu This function controls the percentage of the source USB pen drive to be copied Press ENT to enter the following menu The default setting is 100 You can change the setting to ALL and 1 to 99 of the source drive depending on your needs 10 3 Startup Menu Now press ESC and Y to enter the foll
14. the list of compatible USB pen drives from the ACARD website and check your drive s compatibility Buttons If the buttons are irresponsive they might not work properly Please check the settings of the crossover switches Unreadable USB pen drives If the USB pen drive is unreadable after copying please check the drive through the Compare function or try again with a new pen drive High Failure Rate If the failure rate of data copying is pretty high please following the following procedures to improve it 1 Check if the pen drive has good quality 2 Update the firmware Updating Firmware If you have trouble updating the firmware please check the firmware It might be caused by incorrect file download Failure to update the firmware may make the system unable to start In this case please send the controller board back for repair The Ninth Function and Cancelling To execute the ninth function Adv Setup please press and hold down ESC for 2 seconds You can also cancel a function such as copying and testing during operation by pressing and holding down ESC for 2 seconds y Page 17 of 19 2009 Virtual Vision User Manual CopyBox 7 USB Duplicator LCD Messages LCD Messages Initialize SDRAM Detect Drives User Abort Analyzing Source Drive Not Exist Target Drive Not Exist HDD Image Not Exist HDD Image Read Fail Source Drive Read Fail Target Drive Read Fail Target Drive Write Fail T
Download Pdf Manuals
Related Search