Go to http://www
Contents
1. bay del bay b lt bay id gt delete a bay configuration Sample command line bay add b M1 a The command in the above example is bay The operation is add and the switches are b and a This would add bay M1 with the role of Master Target or Master and Target ZClone Command Line Interface Page 1 of 8 October 2012 Logicube Inc e 19755 Nordhoff Pl Chatsworth CA 91311 USAe te 1 818 700 8488 fax 1 818 435 0088 www logicube com Application Note iK ube Connecting to the CLI To use the CLI users must connect to the ZClone through one of three ways 1 SSH 2 Telnet 3 Serial port Information on how to connect using SSH Telnet or the serial port can be found in the ZClone user s manual Section 7 Remote Operation TIP It is highly recommended to reboot the ZClone prior to connecting to the CLI While connected to the CLI do not perform any tasks on the ZClone as some tasks may interfere with changes performed through the CLI Navigating Inside the CLI Once connected the following prompt will appear it zclone gt e Type help then press the enter key to see the list of commands available on this menu level The key can also be used instead of help to see the list of commands e Type the command by itself for example config bay repo etc to go to that menu for example the config menu or to display the syntax and list of operations and switches for that comm2. Chatsworth CA 91311 USAe tel 1 818 700 8488 fax 1 818 435 0088 www logicube com Application Note iK ube Example 2 Changing bays M1 and M2 from Master only to Master and Target This will allow both M1 and M2 bays to be selectable when choosing a Target drive Steps 1 through 3 connect to the ZClone Steps 4 and 5 navigate to the proper menu prompt Steps 6 and 7 delete the configuration for bays M1 and M2 Steps 8 and 9 add bays M1 and M2 as a Master Target rather than just Master Steps 10 and 11 saves then loads the database configuration The name of the database can be any other name with a db extension Step 12 reboots the ZClone to make sure the correct database or configuration loads 1 Reboot the ZClone Important step After the reboot do not perform any operation clone wipe hash etc on the ZClone until asked to reboot again on step 12 2 Connect to the ZClone CLI via Telnet SSH or serial port as described in the user s manual Section 7 Remote Operation 3 Login using the username it and the password it 4 From the main prompt type command then press the enter key 5 Type config then press the enter key 6 Type bay del b M1 then press the enter key 7 Type bay del b M2 then press the enter key 8 Type bay add b M1 a then press the enter key 9 Type bay add b M2 a then press the enter key 10 Type db save m1m2 db then press the enter key 11 Type db load m1m2 db then press the enter key 12
3. Reboot the ZClone After it reboots M1 and M2 as Master should now be selectable as Master or Target drives Root Menu Command Menu Software Menu Figure 1 Graphical representation of the CLI menu structure ZClone Command Line Interface Page 4 of 8 October 2012 Logicube Inc e 19755 Nordhoff Pl Chatsworth CA 91311 USAe tel 1 818 700 8488 fax 1 818 435 0088 www logicube com Application Note LAni rube Command Line Interface Menus Below is a list of CLI menus and the available commands for each menu To the right is a description of what each command does Top level menu The commands below are available in the top level menu it zclone gt Show available commands Show a list of previously run commands Turn on privileged commands System reserved command Zclone menu enable Exit from current mode Command level menu The commands below are available in the Command level menu it zclone command gt configure unit config Goes to config level menu show information show Goes to show level menu software tasks software Goes to software level menu ZClone Command Line Interface Page 5 of 8 October 2012 Logicube Inc e 19755 Nordhoff Pl Chatsworth CA 91311 USAe te 1 818 700 8488 fax 1 818 435 0088 www logicube com Application Note iK tube Config level menu The commands below are available in the Config level menu which include configuring the database network user
4. Shows the current configuration ZClone Command Line Interface Page 7 of 8 October 2012 Logicube Inc e 19755 Nordhoff Pl Chatsworth CA 91311 USAe te 1 818 700 8488 fax 1 818 435 0088 www logicube com Application Note iK ube Software level menu The commands below are available in the Software level menu which include showing the software version currently installed checking for software updates both via web and USB and updating the software both via web or USB it zclone command sw gt Show available commands Disconnect Disconnect Exit from current mode Show a list of previously run commands Shows the current software version on the ZClone check www usb check for software updates check Command used to check for software updates on the internet or USB U6 update www usb update software update Command used to update the software via internet or USB U6 If you have any questions regarding this application note or using the ZClone please contact our technical support team via telephone at 818 700 8488 opt 3 or via email at support l ogicube com ZClone Command Line Interface Page 8 of 8 October 2012 Logicube Inc e 19755 Nordhoff Pl Chatsworth CA 91311 USAe te 1 818 700 8488 fax 1 818 435 0088 www logicube com
5. repository drive bays tasks buzzer printer temperature image and audit it zclone command config gt help Show available commands quit Disconnect logout Disconnect exit Exit from current mode history Show a list of previously run commands configure database Command used for saving loading listing and removing databases configure network net Command used to configure the ZClone network options DHCP or Static configure user user Command used to add or remove users repo configure a repository use help h for more info Command used to configure repositories used for Drive to Image or Image to Drive modes when cloning bay configure bay role use help h for more info Command used to configure a specific bay to be a Master only Target only or both Master and Target task configure a task use help h for more info Command used to configure tasks without using the GUI clone wipe hash This command can also be used to start show reset and abort tasks export configure a filesystem export use help h for more info Command used to export a filesystem using CIFS or iSCSI buzzer success error on off configure the light tower buzzer for an event Command used to configure the optional light tower with buzzer printer configure a printer use help h for more info Command used to configure a printer repo bay task export buzz
6. Application Note IK tube ZClone Command Line Interface CLI The ZClone is a versatile multi target and multi task drive duplicator To use the ZClone to its full potential a Command Line Interface CLI is included with the device This CLI allows the user to configure and fine tune the ZClone in ways that cannot be done by using the Graphical User Interface GUI Here are some examples of what can be done with the CLI Configure databases set default configurations Configure ZClone network settings Configure user access to CLI Configure repositories local built in and network Configure bays to be set as Master only Target only or both Configure tasks clone wipe hash etc Configure the buzzer and light tower Understanding the Command Line Syntax The CLI requires commands to be typed out rather than a graphical interface where users can touch tap or click icons The syntax for commands entered through the CLI typically consist of three parts The command operation and switch es Some require just the command without an operation or switch For example if the bay command is typed on its own in the config menu it shows bay add set bay b lt bay id gt options master m Role Master target t Role Target hide h Role Not Available all a Role Master Target bay list get the list of all bays and their current roles bay get bay b lt bay id gt get a bay configuration
7. and e Type exit to exit the current mode or go back one menu level e When finished simply disconnect and close the window Please consult the user s manual of the SSH Telnet or Serial Terminal program being used for instructions on how to disconnect a connection TIP Without saving and loading the database changes performed will not take effect Saving and Loading a Database configuration changes Whenever changes are made through the CLI the changes must be saved into a database then loaded again If these two steps are not done the changes will not appear the next time the ZClone is turned on or rebooted A filename must be chosen by the user The two commands are db save filename db db load filename db ZClone Command Line Interface Page 2 of 8 October 2012 Logicube Inc e 19755 Nordhoff Pl Chatsworth CA 91311 USAe te 1 818 700 8488 fax 1 818 435 0088 www logicube com Application Note iK tube Examples of Commonly Used Commands Here are two examples of commands from beginning to end Example 1 Adding a network repository To add a network repository the following information is required A name for the network repository The IP address or hostname of the computer with the shared folder or directory The shared folder or directory name Username and password for the computer with the shared folder or directory must have read amp write access The domain name where the computer is located if appl
8. er printer ZClone Command Line Interface Page 6 of 8 October 2012 Logicube Inc e 19755 Nordhoff Pl Chatsworth CA 91311 USAe te 1 818 700 8488 fax 1 818 435 0088 www logicube com D Application Note Logie C temperature disk system lt temperature gt set the temperature temperature threshold in degrees Celsius Command used to set the temperature threshold me image image management Use help h for more info image Command used to rename or delete images in a repository audit audit log management audit Use help h for more info Command used to rename or delete audit log files Show level menu The commands below are available in the Show level menu which include showing the bay status task configuration or status repository list or contents of one or the configuration it zclone command show gt Show available commands Disconnect Disconnect Exit from current mode Show a list of previously run commands m bay show bay status y Shows status of bays that have drives connected task config lt task id gt status lt task id gt list show task configuration or status Command used to show a list of tasks or the current status or configuration of a task repos list lt repo name gt list repositories or the contents of one task Command used to show the list of repositories or the contents of a repository config show configuration config l i
9. icable A name for the database configuration to be saved so the changes are persistent and will show every time the ZClone is turned on or rebooted anoo m O In this example we will use the following Name for repository netshare1 IP address or hostname 192 168 1 100 or netpc Shared folder name images Username support Password logicube Domain ZC Database name share1 Here are the command line interface commands to use 1 Reboot the ZClone Important step After the reboot do not perform any operation clone wipe hash etc on the ZClone until asked to reboot again on step 10 2 Connect to the ZClone CLI via Telnet or SSH as described in the user s manual Section 7 Remote Operation 3 Login using the username it and the password it 4 From the main prompt type command then press the enter key 5 Type config then press the enter key 6 Type the command to add the repository the example command is based on the information above repo add r netshare1 I Network p smb netpc images U support P logicube D ZC 7 It should show a successful message Next we have to save the database 8 Type db save share1 db 9 Type db load share1 db 10 Reboot the ZClone In the repository location screens for example when selecting a Drive to Image clone netshare1 will be visible as one of the repositories ZClone Command Line Interface Page 3 of 8 October 2012 Logicube Inc 19755 Nordhoff PI
Download Pdf Manuals
Related Search