Instruction of safe use
Contents
1. Replace components as necessary and assemble in reverse order Avoid pinching any wires Be careful that the reflector does not come into contact with LEDs during assembly Carefully insert the o ring seal back in the groove and then place the lens over the o ring The locking ring should be tightened while in the charging stand in order to ensure sufficient tightness EON a on oo FO N IL 6400 lamp disassembly and assembly AUN ow Remove the charging contacts on the bottom of the lamp open Phillips screws Open the six hex socket screws 2 5 mm hex key and remove the lens frame lens and seal Open the hex socket screw 3 mm hex key and lift the reflector out Open the six hex socket screws 2 mm hex key and open the aluminum frame slightly and carefully disconnect the black red wire connector from the LED circuit board Pay special attention to not touch any of the 4 LEDs on the circuit board Slide the carriage unit halfway out of the enclosure if the carriage is stuck tap the lamp gently against the edge of a table and disconnect the pushbutton connector Pull the carriage completely out of the cover Replace components as necessary and assemble in reverse order Avoid pinching any wires Be careful that the reflector does not come into contact with the LEDs during assembly Pushbutton replacement Note The lamp must be disassembled before the pushbutton can be replaced 1 Unscrew the four s2. be discharged fully approximately once a month This helps to avoid the battery memory phenomenon that reduces operating time Please note that you may not install an NiMH battery in an NiCd lamp CHARGING AND STORAGE Do not charge IL 640 amp IL 6400 lamps in charging stands other than the new MICA ILC4 Older MICA charging stands will not charge the lamp correctly but can be upgraded to be suitable contact your dealer for more information IL lamps should be stored in their stands while not in use Please read the charger manual as well CHARGING TIMES IL 640 NiMH 11h IL 640 NiCd 7h IL 6400 NiMH 11h MAINTENANCE During the warranty period components may be replaced by an authorized ATEXOR service agent only Only original ATEXOR spare parts may be used Other procedures will invalidate the warranty IL 640 lamp disassembly and assembly Unscrew the charging contacts on the bottom of the lamp Pozidriv 2 Unscrew the locking ring remove the lens and seal Open the hex socket screw 3 mm hex key and lift the reflector out Carefully disconnect the connector from the LED circuit board Pay special attention to not touch any of the 4 LEDs on the circuit board Open the Torx T20 key screws and remove the LED module Slide the carriage unit halfway out of the enclosure if the carriage is stuck tap the lamp gently against the edge of a table and disconnect the pushbutton connector Pull the carriage completely out of the enclosure
3. crews holding the switch cover plate in place 2 Remove the cover plate and the rubber cover and remove the switch from the inside of the cover 3 Before reassembling check that the rubber cover is intact since its condition is crucial to the ingress protection of the lamp SPARE PARTS 1 22002 Battery pack 9 0 Ah NiMH 7 M01297_X Glass lens 22006 Battery pack 5 5 Ah NiCd 8 21017 IL 640 LED module Cool 2 M00940 Charging contact assembly 21018 IL 640 LED module CRI 3 16034 IL 640 lamp body NiMH 21019 IL 6400 LED module Cool 16035 IL 640 lamp body NiCd 21020 IL 6400 LED module CRI 16036 IL 6400 lamp body NiMH 9 M02867 IL 640 O ring seal 1 pc 4 MH0101_2 Switch cover assembly black 10 MH0106_3_ IL 6400 O ring seals 2 pcs NiMH lamps 11 21013 IL 640 main circuit board MH0101_1 Switch cover assembly grey 21014 IL 640 EM main circuit board NiCd lamps 21015 IL 6400 main circuit board 5 M03356 Pushbutton assembly 12 16023 Reflector 6 M00895 IL 640 locking ring black 13 M01193 Internal cassette assembly NiMH lamps 14 M02673 Gore Tex valve M01264 IL 640 locking ring grey 35032 IL 640 screw set NiCd lamps 35033 IL 6400 screw set M02862 IL 6400 lens frame 70705 IL shoulder strap ACCESSORIES M11350 Red filter plastic IL 640 M11351 Green filter plastic IL 640 M11352 Orange filter plastic IL 640 M11357 Diffuser filter plastic IL 640 M11265 Flashlight stand IL 640 6400 M11266 Filter pouch IL 640 TECHNICAL SPECIFICATIONS Light s
4. e L 640 IL 640 EM o IL 6400 User Manual MICA Please read this manual carefully in order to experience the full benefits of your lamp Please store the manual for later use USING THE LAMP The charge of the lamp s battery will be reduced when the lamp is stored The lamp must be carefully charged prior to use by using a MICA ILC4 charging stand The battery will be charged from empty to full in 6 to 12 hours depending on the temperature and condition of the battery A new battery will reach its full capacity when it has been fully charged and discharged about ten times The first charging of a new lamp must take at least 12 uninterrupted hours OPERATING MODES A pushbutton controls the functions of different lamp models as follows IL 640 LOW POWER gt FULL POWER gt OFF IL 640 EM LOW POWER gt FULL POWER gt OFF If the lamp is in the charging stand and a power failure occurs the lamp is automatically lit at LOW POWER IL 6400 LOW POWER gt FULL POWER gt OFF Boost is available when the lamp is switched on IL 6400 is equipped with a Boost function which is activated by holding the button down IL 6400 will provide over 50 more light in Boost mode compared to FULL POWER but it is intended to be used only briefly to prevent overheating The function stays on for as long the button is held down IL 640 EM SAFETY LIGHT The light will be automatically turned on when the lamp is in the char
5. ging stand and the charging power is cut off power failure etc IL 640 EM is always automatically in safety light mode when placed in the charging stand Manufacturer ATEXOR OY P O Box 89 FIN 60101 SEINAJOKI Tel 358 207 343 250 Internet www atexor com MICA IL 640 IL 640 EM IL 6400 User Manual OPERATING TIMES The operating time with a fully charged battery depends on the lamp model and the operating mode used see table PY L640 NiMH IL 640 NiCd IL 6400 NiMH LOW POWER 24h 16h 24h FULL POWER 8h 5h 5h The series of red LEDs under the handle show the battery charge If only one LED is on and or the lamp begins to flash approximately every 15 seconds the lamp battery is almost empty 10 20 minutes remaining The control electronics will automatically turn off the lamp prior to deep discharge of the battery In an emergency the lamp can still be used for a short period of time but the battery s service life will be reduced The operating time will become shorter as the battery ages If the overall operating time remains clearly below the values stated in the table even with a fully charged battery the battery should be replaced TO BE TAKEN INTO ACCOUNT WHEN USING LAMP In case of NiCd batteries in order to guarantee the longest service life possible the battery should be discharged completely from time to time by leaving the lamp on until it automatically shuts off Lamps equipped with NiCd batteries should
6. ource 4 x Cree LED Battery NiMH 6V or NiCd 6V Operating temperature range 20 C 40 C Ingress Protection class IP67 Dimensions 215mm L x 120mm W x 125mm H Weight MICA IL 640 with NiMH battery 1 4 kg with NiCd battery 1 3 kg MICA IL 6400 with NiMH battery 1 6 kg TERMS AND CONDITIONS OF GUARANTEE A two year guarantee from the purchase date is granted for the MICA lamp covering any manufacturing and material defects according to generally applicable terms and conditions of guarantee Please note that the guarantee period for the battery is six months The guarantee becomes void if the adjustment values of the electronics components have been changed or if any components have been damaged in any other way Under the warranty period the lamp may be serviced by an authorized Atexor service agent only For maintenance repair please send the lamp and the charger stand as well as the purchase receipt with the product Note A new MICA lamp battery must be used or recharged within three 3 months of manufacture 5 2014 ATEXOR OY We reserve the right to make changes to these user instructions without advance notice ee Manual_IL 640_IL 640 EM_IL 6400_ENGL_5 2014_lowress
Download Pdf Manuals
Related Search