MIDI WOWEE-WAH MWW-1 User Manual
Contents
1. e Connect the device into an outlet on a circuit different from that to which the receiver is connected e Contact with the manufacturer e Consult the dealer for help Certificate of Conformity ELZAB S A ul Kruczkowskiego 39 41 813 Zabrze Poland hereby declares on own responsibility that the following product MIDI WOWEE WAH G LAB MWW 1 that is covered by this certificate and marked with CE 07 label conforms with following standards PN EN 60065 2004 Safety requirements for mains operated electronic and related apparatus for household and similar general use PN EN 55103 Product family standard for audio video audiovisual and 1 1998 entertainment lighting control apparatus for professional use Part 1 Emission PN EN 55103 Product family standard for audio video audiovisual and 2 1998 entertainment lighting control apparatus for professional use Part 2 Immunity with reference to regulations in following directives 73 23 EEC 2004 108 EEC Issued in Zabrze April 2009 Jerzy Biernat President of the ELZAB S A Board of Directors 12 DO NOT PLACE THIS PRODUCT INTO THE WASTE CONTAINER This device is marked with a cross lined waste container symbol according to 2002 96 EU Directive on Waste Electric and Electronic Equipment pm Such marking informs that after usage equipment can not be trashed together with other household waste An user obligation is to return wasted equipment to a party collecting was2. LOW 64 127 HI SET ALL Prog Chang number Regulation of the resistance to motion force MIDI WOWEE WAH posses the ability to adjust the resistance to motion force by using the spring set screw For regulation it is needed to use the 7 mm open ended spanner Screwing in of the screw increases the resistance to motion min 0 mm max 5mm ATTENTION Do not screw out the screw more than indicated on the picture Technical parameters Dimensions width 99 mm depth 250 mm height 85 mm Weight 1 4 kg Power supply 9V DC 8 7 do 9 4V regulated Current consumption 30 mA 10 EMC EMI amp Certificate of conformity EMC EMI This device has been designed and manufactured to conform with directives and standards in the field of safety operations and electromagnetic interference This device uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However in spite of performing below standards there is no guarantee that interference will not occur in a particular installation If this device does cause harmful interference to radio or television reception which can be determined by turning the device on and off the user is encouraged to try to correct the interference by one or more of the following operations e Reorient or relocate the receiving antenna e Increase the separation between the device and receiver
3. GILAB GUITAR LABORATORY www glab com pl WOWEE WAH User Manual Mode d emploi W Instrukcja obs ugi BI Bedienungsanleitung Version 1 1 Table of contents Structure Switches functions Basic ideas of the tone switches settings Power supply Connecting to a gear MIDI channel setting D O N N OOO A Controlling via MIDI commands Regulation of the resistance to motion force 10 Technical parameters 10 EMC EMI amp Certificate of conformity 11 Dear Customer Thank you for choosing our product MIDI WOWEE WAH MWW 1 is a classic analog wah wah effect enabling to set the tones and featuring new and comfortable switching mode MIDI interface enables fast switching of the tones by using any MIDI controller e g G LAB GSC Basic characteristic Full analogue circuit with an increased voltage which ensures functionality without distortion and a lower noise level Photo element instead of potentiometer which ensures smaller resistance to motion thanks to that the smaller effort allows you to operate the pedal faster and greater reliability BASS switch LOW bass attenuation like in typical wah wah HIGH without bass attenuation DEEP switch to control the depth of the resonance circuit functionality Q FACTOR switch quality factor of the resonance circuit decreases boosting of resonance frequency VOLUME switch to control the output signal level Two ON
4. OFF switching modes classic with the use of the switch located in front of the pedal SWITCH mode or our new mode simple by placing the foot on the wah wah pedal TOUCH Clickless TRUE BYPASS circuit that is based on photo resistors Two backlighted indicators on the left and right side of the wah wah visualising active mode of the wah wah effect yellow colour to make it easy for you to find the wah wah on a dark stage MIDI IN connector to control the wah wah by Program Change and Control Change commands MIDI THRU connector with copy of the signal form MIDI IN connector Regulation of the resistance to motion force Powder coated case and stainless steel elements 9V supply from regulated adapter 9V DC current consumption 30 mA Structure BASS HI LOW switch MIDI IN and MIDI THRU connectors OUT connector 9V DC power supply connector MIDI IN channel switch Functions indicators VOLUME HI LOW switch ON OFF mode switch IN connector Q FACTOR HI LOW switch DEEP HI LOW switch Effect active mode indicators Switches functions BASS DEEP Q FACTOR VOLUME Switch LOW bass attenuation like in a classic wah wah HIGH without bass attenuation Switch changing the effect intensity HIGH position decreases the signal level of the frequencies behind the resonance what increases effect intensity in all range of pedal regulation a side effect is attenuation of the s
5. OWEE WAH from 9V DC regulated adapter with a capacity of 30 mA or more Before plugging the adapter please check the pin polarization CTR center negative DECO ATTENTION Damages caused by improper power supply causes the loss of the warranty Connecting to a gear It is recommended to connect WOWEE WAH between the guitar and amp and if using other guitar effects between the guitar and stompboxes MIDI channel setting To set a MIDI channel on which the MWW 1 receives the commands serves MIDI CHANNEL rotatable switch To change the channel use a small screw and turn it a little right or left The arrow head indicates set channel A B C D E F letters correspond with 10 11 12 13 14 15 channels numbers and 0 digit indicates channel No 16 Controlling via MIDI commands MWW 1 can be controlled by Program Change and or Control Change commands The Program Change number should be counted by following formula Prog Change 1 if BASS HI 2 if DEEP HI 4 if Q FACT HI 8 if VOL HI If all the functions are set on LOW the Prog Change 16 DEEP PROGRAM The table below shows numbers and functions of Control Change commands Controllers from 104 to 107 serve to control individually each function and controller number 86 functions similarly to the Program Change command Controler s BASS 0 63 LOW 64 127 HI DEEP 0 63 LOW 64 127 HI Q FACT 0 63 LOW 64 127 HI VOLUME 0 63
6. ignal it is recommended to set VOL switch on HIGH position Quality factor of the resonance circuit switch HIGH position increases resonance signal level especially of low part of the regulation band high pedal positions what intensifies the wah wah effect Volume of the effect signal HIGH position increases the signal by 3 5dB ON OFF MODE Switching mode switch SWITCH position classic mode by using of the switch located in front of the pedal TOUCH position pressure activated mode by placing the foot on the wah wah Basic ideas of the tone switches settings IM Classic deep wah wah effect with bass attenuation crunch High intensity of the wah wah effect on low part of the regulation band VOL HI position boosts the signal for more overdrive Low intensity of the wah wah effect on low part of the regulation band reducing choking of the gain by low frequencies of regulation high HI LO LO A e Low intensity of the wah wah overdrive effect assuring its legibility fV VOL HI position boosts the signal for more overdrive LO LO HI Y Y High intensity of the wah wah effect on middle and low part of A the regulation band VOL HI position boosts the signal for more overdrive If MWW 1 is controlled by MIDI interface switching of any of the tone switches causes setting of the tone defined by the switches mode Power supply It is recommended to supply the W
7. ted electric and electronic equipment Parties collecting such equipment organise a system including local collection points shops and other units allowing to return such equipment This Directive assures an user free of charge utilisation of such delivered equipment This device is made of materials which can be recycled or utilised after becoming out of use Proper handling of wasted electric and electronic equipment reduce demand for row materials and contribute in avoiding harmful consequences for environment and health of people caused by dangerous components and not proper storing and utilising of such equipment User Manual Drawing No G411NAOO GILAB GUITAR LABORATORY G LAB is a brand of ELZAB SA COMPANY ADDRESS ELZAB SA ul Kruczkowskiego 39 41 813 Zabrze Poland phone 48 32 272 20 21 fax 48 32 272 81 90 Sales amp Export Department ssssse phone 4 48 32 272 30 51 ext 34 39 64 48 32 272 20 21 ext 308 366 468 e mail glab glab com pl Technical Guppor CT 2 22 coo se ono aa so a uas sna ra aono ra phone 48 32 272 30 51 ext 64 48 32 272 20 21 ext 308 e mail help glab com pl www glab com pl Nr rys G41TINOO
Download Pdf Manuals
Related Search