DL Display Line
Contents
1. HA2 PORKKA LA2 PORKKA P1 33 PORKKA Pp2 PORKKA P3 I D l Z TT REASON High temperature alarm The temperature inside the cabinet has exceeded the set alarm temperature The alarm can be instigated by sudden icing of the evaporator Initiate manual de frosting see instructions on page 4 Ensure the cabi net has not been loaded with warm products Check that a door has not been left open Check if product is blocking air circulation within the cabinet Low temperature alarm The temperature inside the cabinet has fallen below the set value Ensure that the products put into the cabinet are not too cold The temperature alarm is reset automatically after the interior of the cabinet returns to set temperature range If this does not happen move the products to another cabinet and contact your service provider Condenser high temperature alarm The condenser filter needs to be cleaned Switch the cabinet to standby mode remove cover and clean the filter by washing and or using a soft brush and vacuum cleaner Remove dirt and debris from the condenser face Check also that air circulation to the condenser is not blocked or that the ambient temperature is not too high If the alarm still does not stop remove products to another cabinet and contact you service provider Condenser low temperature alarm Thermostat probe failure Evaporator probe failure Condenser probe fa2. beginning of the defrosting period are displayed After that the display returns to the normal mode Manual defrosting Push N key for 3 seconds when the manual defrosting will start After manual defrost the cabinet will continue to defrost at regular intervals Manual defrosting is recommended if there is a lot of ice on the evaporator i e if the door has been left open for a long time or if warm uncovered food has been placed in the cabinet To check the lowest temperature Push W key Code Lo is displayed after which the lowest registered temperature is displayed The display returns to the normal mode automatically after 5 seconds To check the highest temperature Push AN key Code Hi is displayed after which the highest registered temperature is displayed The display returns to the normal mode automatically after 5 seconds To delete the lowest and highest temperatures registered The registered lowest and highest temperatures are deleted separately Get the lowest and highest temperature registered on the display by pushing the arrow key ZX or NY Push immediately the SET key for 3 seconds until the code rST reset starts to flash on the display Release the key and the temperatures have been deleted and the display returns to the normal mode ALARM SIGNALS FOR COMBINED CONTROLLER AND DIGITAL TEMPERATURE DISPLAY CODE HA PORKKA LA PORKKA Reset the alarm signal by pushing SET key
3. Cleaning operator s responsibility To remove a handle Good to know If the cabinet does not function correctly Disposal of the equipment Guarantee Service during the guarantee period EO N D AARAA AWWW OW W O N 414 NN O 0 OD O O1 RECEIPT Check the product as soon as you receive it If you notice that it has suffered from damages during transportation you must indicate this in the delivery documents and tell about the matter to the carrier off the retailer The manufacturer s guarantee does not cover damages caused by transportation INSTALLATION AND INTRODUCTION Unpack the cabinet as close to the installation place as possible Remove the protective films on exterior surfaces of the cabinet Sort packing material and dispose off according to local legislation reguirements Avoid placing the cabinet in direct sunlight or close to any eguipment radiating heat such as cookers and radiators The ambient temperature must not exceed 25 or fall below 5 C Ensure the cabinet is horizontal if necessary use spirit level The legs are adjustable All legs must touch the floor with even weight loading per leg If the cabinet is eguipped with castors it must be placed on an even level surface Uneven floor can distort the frame of the cabinet and cause height differences between units Lock the castors with brakes once the unit is in position Clean the cabinet carefully before usage using a mild dete
4. DL Display Line ASENNUS JA KAYTTOOH EET INSTALLATIONS OCH BRUKSANVISNING INSTALLATION AND OPERATION MANUAL INSTALLASJ ONS OG BRUKSANVISNING 2011 10 JE D l Z TT THESE INSTRUCTIONS ARE FOR CHILLED FOOD DISPLAY LINE DL CL IT IS VERY IMPORTANT TO READ THESE INSTALLATION AND OPERATING INSTRUCTIONS CAREFULLY BEFORE YOU START USING THE EOUIPMENT FOR THE FIRST TIME ALSO PLEASE KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE OR USE BY ANOTHER OPERATOR BY FOLLOWING THESE INSTRUCTIONS YOU CAN IM PROVE THE PRODUCT S PERFORMANCE AND REDUCE UNNECESSARY REPAIR COSTS PLEASE NOTE ITIS IMPORTANT TO HAVE YOUR EQUIPMENT REGULARLY MAINTAINED BY A PROFESSIONAL ENGINEER YOU WILL FIND THE TERMS OF GUARANTEE ON PAGE 7 TABLE OF CONTENTS Receipt 2 Installation and introduction Couplers of the cooling unit the air forced cooling of display area on off function Use Combined controller and temperature display keyboard locking and unlocking the keys function of the key lamp lights function of the display lights main switch to modify the temperature set points defrosting manual defrosting to check the lowest temperature to check the highest temperature to delete the lowest and highest temperatures registered Alarm signals for combined controller and digital temperature display Cooling unit removal of the unit for cleaning and servicing Operator s user s responsibility
5. be caused by e g a door gt that has been left ajar or high air humidity Check inside the unit if there is ice in the air circulation openings of the rear edge of the cold machine cassette If you notice ice or if you suspect that the evaporator has frozen start manual defrost according to the instructions Repeat manual defrosts until the evaporator is completely free of ice In case the product still does not reach the temperature needed contact a service company I D l Z TT If the machinery gives a strange sound check that the feet of the cabinet are adjusted properly Make sure that the cabinet does not rock when pushed from one or another of the front corners ensure that goods inside the unit e g bottles do not clink against each other DISPOSAL OF THE EOUIPMENT Once the equipment becomes redundant it may not be disposed of with normal waste because the eguipment is governed by the WEEE directive It has to be disposed of following the WEEE act which became effective on August 13th 2005 GUARANTEE Check the guarantee period at your merchandiser The guarantee does not cover faults caused by transportation overloading or users negligence negligence due to not reading manuals proper care and maintenance changes in current max 10 allowed caused for example by lightning etc modifications or repairs performed by an unauthorized service agent use of parts not s
6. e key for 3 seconds the set point can be modified JE D l Z TT PORKKA Note The temperature of the lower storage area of the cabinet can be changed from 4 to 12 C when the temperature in the display area compartment will be 6 to 15 C The top shelve of the display area when fitted with three shelves is not chilled Note The manual defrosting resets the defrosting time counter so that by means of the manual defrosting period the regular defrosting periods can be scheduled to take place e g outside the peak periods Note After the first start reset the lowest and highest temperatures stored Main switch The cabinet is switched on and off by using the main switch When you move to the standby mode the code OFF is displayed In the standby mode all the control functions are off If the product is connected to the monitoring system it does not receive control or alarm data from the monitoring unit The light switch functions when the instrument is on standby To modify the temperature set points Push SET key 3 seconds and the temperature set point flash on the display Modify the value by pushing Lx or 7 key within 15 seconds Save the new value by pushing SET key again or wait for 15 seconds after which the display returns to the normal mode Defrosting The evaporator is defrosted automatically During the defrosting period the defrosting LED and temperature in the
7. ilure Note The cabinet operates on its standby system and will hold normal temperature but reset the alarm signal and immediately contact your service provider E D l Z TT COOLING UNIT Removal of the unit for cleaning or servicing standby button and remove socket Remove the grating 1 Lift it lower edge outwards when the grating will come off Switch off power supply by the socket for shelf cooling and for light 2 edge of the unit 3 Pull the cooling unit out Replace by reversing procedure Operators user s responsibility ie Clean the condenser filter on the cooling unit 4 two times a month or when necessary Remove the filter and rinse under running water Shake off excess water and replace filter Clean the finned condenser on the unit 5 once a month using a soft brush and or vacuum cleaner Take care not to damage fins If the cabinet is situated in a very dusty environment i e bakery it has to be cleaned more often The cooling unit should be removed and serviced by a professional company 1 2 times per year CLEANING AND MAINTENANCE Clean spillages immediately Ensure effective operation of the equipment and the quality of the stored products by defrosting and cleaning the equipment once a month at least Switch off cabinet by pressing straight upwards and draw the removing socket Also remove Loosen 2 screws on the lower Rem
8. locking the keys A E VA The key lock prevents unintended use of ere the keys The lock is switched on and off by holding the keys down at the same time for 3 seconds The display momentarily shows letters PoF With key lock on you can still check the lowest and highest temperature 2 Socket for light registered The light switch function can still be used when keypad is locked Pon means that the keys are not locked 1 Socket for the electric wire 3 Combined controller and digital temperature display THE AIR FORCED COOLING OF DISPLAY AREA ON OFF FUNCTION Display lights LIGHT MODE FUNCTION OFF On The equipment is on standby mode o Set temperature is displayed and can be C Flashing handen W On Light is on e On Compressor is running 4 v SAARA sk Flashing Time delay to protect compressor after The air forced cooling of display area shelves can be turned off by a start up slide even if counter and basin is switched on e On The fan of the evaporator is on USE COMBINED CONTROLLER AND DIGITAL TEMPERATURE DISPLAY ne On Defrosting of the evaporator is on Keyboard ES Flashing Drying of the evaporator is on On ALARM see alarms on page 5 SWITCH FUNCTION Of Light switch The manual defrosting starts when you push the key for 3 A seconds The key to display and adjust the set point In the pro SET gramming mode the adjusting function is quitted by this key By pressing th
9. nclude commercial kitchens restaurants fast food outlets hotels industrial canteens hospitals laboratories and retailers throughout Europe Our main markets outside of Finland include Scandinavia United Kingdom Germany Switzerland Holland Belgium Russia and the Baltic regions 80 of the companies turnover is derived from foreign transactions and exports Ongoing and adaptive development by numerous foreign subsidiaries and representatives ensures our continued success Porkka s continued success is based on decades of experience customer focused design and continuous product development New innovative products are launched each year Porkka Finland Oy is part of the Huurre Group Porkka and Huurre brands are well known for their guality and reliability Porkka Finland Oy Sis lt Kioton p yt kirjan soveltamisalaan kuuluvia isal i fluorattuja kasvihuonekaasuja Kylm aine ja t ytt m r Soisalmentie 3 on ilmoitettu laitteen arvokilvess Ilmatiiviisti suljettu F1 15860 Hollola Finland x N a RoHS ontains fluorinated greenhouse gases covered by Tel 358 20 5555 12 the Kyoto Protocol Refrigerant and charge size can be Fax 358 20 5555 497 found on the name plate Hermetically sealed eguipment REACH e mail porkka huurre com SIA T www porkka fi R134a GWP 1300 Kaikki oikeudet muutoksiin pid tet n R290 GWP 3 All rights reserved O Porkka Finland Oy
10. ome to the normal level before using the equipment again TO REMOVE A HANDLE The handles of the doors and drawers are removable You can easily change a damaged handle to a new one Snap the handle end carefully with a hammer and the handle moves to the right Make sure the drawer is properly closed so that the mechanism will not be dam aged of the snap Take the handle off the holes Put the handle back in reverse order GOOD TO KNOW aM we 1 Air duct channels on the ends of compartment s shelves must not be covered 2 Shelve LED illumination and the well LED light are supplied as standard in the display area compartment 3 Bottom plates of the bottle basin are adjustable IF THE CABINET DOES NOT FUNCTION CORRECTLY The machine does not start check that the main switch has been turned to ON check that the electric cable has been connected to a socket check that the fuse of the socket is undamaged The cabinet does not become cool or does not reach the wanted temperature check that the thermostat has been correctly adjusted SET button to modify the temperature set points the defrost is not on the defrost LED is on the control unit air circulation inside the unit is not blocked Check that the ambient temperature is not too high the air circulation for the condenser is free and the filter of the condenser is not blocked evaporator has not frozen E This can
11. ove all food and store it in a back up store Switch off the unit from the main electrical power switch and take off the electric wire from the wall socket Remove shelves and GN rails as well as drawers and runners and shelf support uprights Wash the stainless steel surfaces of the equipment by a mild detergent mixed with water e g dishwasher detergent or other suitable detergent Use a cloth or a paper towel to prevent scratching RINSE WITH A DAMP CLOTH DRY AND ALLOW THE CABINET TO DRY OUT DO NOT USE DETERGENTS OR DESINFECTANTS CONTAINING CHLORINE SOLVENTS SCRUBBING PRODUCTS A KNIFE OR OTHER SHARP TOOLS DO NOT USE RUNNING WATER TO WASH THE CABINET THE COOLING UNIT OR THE CABINET WITH THE COOLING UNIT IN PLACE REFER TO THE PRODUCT DESCRIPTION OF THE DESINFECTANT TO SEE WHICH MATERIALS IT IS SUITABLE FOR DO NOT LET IT SPLASH ON SENSITIVE PARTS SUCH AS THERMOSTAT REGULATOR OR DOOR HINGES DRY THE EQUIPMENT AFTER THE DESINFECTION AND LET IT VENTILATE Clean the condenser and or condenser filter Clean the cabinet door gasket using a mild water soluble detergent and check the condition of the gasket A silicone spray makes the gaskets flexible and dirt rejecting Lubricate the drawer runners with lubricant suitable for food stuff Cleaning in dishwasher is not recommendable for the loose parts of the equipment Put back all removed parts and switch on the equipment Ensure that the temperature has bec
12. rgent Do not use scouring powder wire wool or chlorine i e bleach type cleaners When cabinet is delivered and if temperature is cold condensation may form on the exterior surface Do not connect power until unit is dry and at room temperature The unit should be connected to an earthed socket or isolator with 220 240 V 50 Hz supply It should be protected with a fuse of 10 amp rating Display Line cold cabinets are designed and tested for selling and storing of pre cooled products Note It is extremely important to keep foods with high acidity such as pickles and salad dressings in air tight containers Highly acidic foods will corrode the evaporator resulting in expensive repair work which will not be covered by warranty Ensure there is free air movement beneath the cabinet The product must not be used outdoors or be subjected to excessive amounts of sprayed water especially near the temperature display COUPLERS OF THE COOLING UNIT SWITCH FUNCTION 1 2 The key shows the highest thermostat value A registered In the programming mode you navigate inside the program or it is used to raise the selected value I D Z TT The key shows the lowest thermostat value registered In SV the programming mode you navigate inside the program or it is used to lower the selected value 1 Power switch Note The power operation light remains illuminated even when power is switched off eee Locking and un
13. upplied and approved by the manufacturer The guarantee does not cover incidental scratches marks or other minor faults caused when unpacking or during installation that does not effect operation or performance of the equipment THE MANUFACTURER OR HIS SELLING AGENT IS NOT AT ANY TIME OR UNDER ANY CIRCUMSTANCES LIABLE FOR FOOD LOSS HOWSOEVER IT OCCURS THE OWNER USER SHOULD ENSURE THE CONTENTS ARE INSURED AT ALL TIMES ALL GOOD ARE SUPPLIED UNDER OUR TERMS AND CONDITIONS OF SALE A COPY OF WHICH MAY BE OBTAINED UPON REQUEST Porkka Finland Oy on kansainvalisesti tunnettu kylmalaitevalmistaja Merkittavimmat asiakkaat ovat ammattikeittioita ravintoloita hotelleja teollisuuslaitoksia sairaaloita laboratorioita ja vahittaiskauppoja eri puolilla Eurooppaa Yrityksen paamarkkinat ovat kotimaan ohella Skandinavia Englanti Saksa Sveitsi Hollanti Belgia Ven j sek Baltia Liikevaihdosta 80 kertyy ulkomaisesta liiketoiminnasta ja viennist Joustavaa kehityst tukevat lukuisat ulkomailla sijaitsevat tyt ryhti t ja edustajat Porkka Finland Oy n menestys perustuu vuosikymmenten kokemukseen asiakasl ht iseen suunnitteluun ja jatkuvaan tuotekehitykseen Uusia tuotteita lanseerataan vuosittain Porkka Finland Oy kuuluu Huurre Group konserniin Porkka ja Huurre tuotteet edustavat aina luotettavaa laatua Porkka Finland Oy is an internationally recognised designer and manufacturer of refrigeration eguipment Major clients i
Download Pdf Manuals
Related Search