Data Input YDI50Z. Dedicated Keyboard Rated to IP
Contents
1. Power cord Interface cable for connection to an MP 8 balance scale Fuse Keyboard overlays for the function keys How to Set Up the YDI 50 Z Data Input Keyboard Set up the Data Input dedicated keyboard in a suitable area If you plan on connecting peripherals such as a balance or scale with an interface a printer etc make sure that the ambient conditions are also suitable for these devices How to Adjust the Voltage Selector to Your Local Line Voltage The Data Input keyboard has been factory set to 220 volts To adjust the voltage selector to the local line voltage rating that you use unscrew the cover plate from the base of the YDI 50 Z keyboard Then adjust the voltage selector to your local line voltage rating Write the new voltage setting on the manufacturer s label Whenever you change the operating voltage to 100 120 V make sure to exchange the installed T 80 mA fuse for the T 160 mA fuse that comes with the Data Input keyboard The fuse 12 is located on the side panel of th Data Input keyboard How to Connect the Data Interface Cable and the Power Cord Connect the data interface cable to th balance scale first with the unit unplugged then to the YDI 50 Z Data Input keyboard Plug the power cord of the Data Input keyboard into a properly installed wall outlet Important Note If you connect your Data Input keyboard t2. 2 4 program dependent switch setting How to Adjust the Contrast of the LCD Located between the DIP switches 2 is a small screw which you can use to adjust the contrast of the LCD Please refer to the program description for information on the switch setting Keypad Description The keypad consists of the CE key CF key numeric keys function keys and the ENTER key PRINT key on some models n addition each function key has an LED which can be activated or deactivated by the program Keys Function Clear Function sE Press this key to end a program Clear Entry Fe This key deletes digits a zero is displayed umeric keys Use these keys to enter digits 4 5 6 and decimal points 1 2 3 0 Function keys F1 Re fe You can insert different keyboard F4 F5 F6 overlays for the software programs ENTER he ENTER key has functions which change based on the program The functions are described in the user s manual for each set of programs Adapting the YDI 50 Z Data Input Keyboard to Individual Requirements Additional devices can be connected to the two additional interfaces 3 4 Configuration Options COM A and COMB in the Sartonet Mode In the SARTONET mode up to 32 units can be connected in parallel to one data interface cable SARTONET system for networking YDI 50 Z Data Input k
3. Germany on paper that has been bleached without any use of chlorine W1A000 KT Publication No WYD6068 197054 sartorius
4. Re 98646 000 60 Data Input YDI 507 Dedicated Keyboard Rated to IP 65 with LCD Installation and Operating Instructions sarforius UOT UMN NUE sa rtorius a a NCEE fag SEED iy B o sart rius LCD LCD An DIP swi the con DIP Sch r den zeige Affichage LCD tches and screw for adjusting trast of the LCD alter und Stellschraube Kontrast der LCD Anzeige Commutateurs DIP et vis de r glage pour le contraste de l affichage LCD COM B COM B COMB COM A COM A COMA Manufacturer s label Typenschild Plaque CF key signal tique clear function CF Taste Clear Funktion Touche CE key CF Clear Function clear entry CE Taste Clear Entry Touche CE Clear Entry 10 11 12 13 14 Numeric keypad Zahlenblock Bloc num rique Function keys Funktionstastenfeld Touches de fonctions PRINT key PRINT Taste Touche d impression PRINT ON OFF switch EIN AUS Schalter Commutateur Marche Arr t ON OFF Fuse Netzsicherung usible de secteur CTI nterface for connecting the balance scale Waagenschnittstelle nterface balance Voltage selector Spannungsw hler S lecteur de voltage Contents Page About the Product Warranty 4 Storage and Shipping Conditions 4 Equipment Supplied 5 How to Set Up the YDI 50 Z Data Input Keyboard 6 How to Adjust the Voltage Selector to Your Local L
5. ce scale Data Input keyboard SARTONET data interface Additional Literature SARTONET Description and User s Manual Interface Description for Sartorius Balances and Scales MP 8 4 98647 000 03 Specifications Model YDI 50 Z Power requirements 110 120 220 240 V selectable approx 30 VA 50 60 Hz Fuse T 80 mA 160 mA for 110 120 V Dimensions of the housing W 260 mm D 160 mm 210 mm incl plug H max 110 mm Weight 3 kg Temperature range 10 C to 40 C ROM for programs 64 KB Data memory 32 KB LCD 20 characters 2 lines backlit Protection rating IP 65 Marking CE The CE marking affixed to the equipment indicates that the equipment meets the requirements of the following Directive s issued by the Council of the European Union 89 336 EEC Electromagnetic compatibility EMC Applicable European Standards Limitation of EN 50081 1 Residential commercial and emissions light industry EN 50081 2 Industrial environment Defined immunity to EN 50082 1 Residential commercial and interference light industry EN 50082 2 Industrial environment Important Note The operator shall be responsible for any modifications to Sartorius equipment and for any connections of cables or equipment not supplied by Sartorius and must check and if necessary correct these modifications and connections On request Sartorius will provide info
6. eyboard functions as the MASTER and all other connected devices are referred to as SLAVES please see Additional Literature on page 12 data interface balance scale interface SARTONET RS232 ISLAVE balance scale YDI50Z peripheral 1 SLAVE SARTONET eee a eee COM B Pee MASTER balance scale YDI50Z COM A SARTONET peripheral 2 SLAVE balance scale interface RS232 SLAVE balance scale YDI507Z SARTONET data interface COM A and COMB in the RS 232C Mode If you operate COM A and COM B in the RS 232C mode you can directly connect other devices such as a com or a spectrometer please s balance scale Additional Literature on page 12 puter a printer a floor scale a recorder printer RS 232C COM B YD1I50Z Data Input keyboard COM A RS 232C floor scale COM A in the Sartonet Mode and COM B in the RS 232C Mode You can connect a printer to COM B and simultaneously work with COM A in the Sartonet mode printer RS 232C COM B YDI507Z MASTER balance scale Data Input keyboard COM A SARTONET peripheral 2 YDI507Z SLAVE balan
7. ine Voltage 6 How to Connect the Data Interface Cable and the Power Cord 6 Adjusting the Data Transmission Rate of the Balance Scale Interfac 7 Turning the YDI 50 Z Data Input Keyboard On and Off 7 Overview of the DIP Switch Settings 8 How to Adjust the Contrast of the LCD 8 Keypad Description 9 Adapting the YDI 50 Z Data Input Keyboard to Individual Requirements 9 Configuration Options 10 Additional Literature 12 Specifications 13 C Marking 14 About the Product Warranty The YDI 50 Z Data Input dedicated keyboard is a programmable terminal that can be connected to all MP 8 and MCT Balances and Scales that are equipped with an interface MC1 Balances and Scales must have a YDO 01 interface Read these Installation and Operating Instructions carefully before operating your Data Input keyboard Do not miss out on the benefits of our full warranty Please complete the warranty registration card indicating the date of installation and return the card to your Sartorius dealer Storage and Shipping Conditions Storage temperature 40 C 470 C AO F 158 F After unpacking the Data Input keyboard please check it immediately for any visible damage as a result of rough handling during shipment Save all parts of the packaging and the box because you may need to ship your equipment Before you pack your equipment to ship it unplug all connected cables to prevent damage Equipment Supplied
8. o a power supply which does not have a protective grounding conductor be sure to ground the unit For information on startup of the balance scale please refer to the installation and operating instructions supplied with it Adjusting the Data Transmission Rate of the Balance Scale Interface To adapt the Data Input keyboard and the balance scale it is necessary to change the data transmission rate in the balance scale operating program from 1 200 baud to 9 600 baud see the installation and operating instructions of the balance or scale you are using For this purpose change code 224 to 227 Turning the YDI 50 Z Data Input Keyboard On and Off You can turn the YDI 50 Z on and off using the ON OFF switch 11 O no power power is on Important Note Always unplug the Data Input keyboard and the balance scale from line power before you connect or disconnect devices to or from the interface ports Overview of the DIP Switch Settings itches 2 are located behind a cover plate ide of the Data Input keyboard 1 OFF V24 mode 2 OFF V24 mode ON Sartonet 2 ON Sartonet 3 not assigned not assigned itch S221 m dependent switch setting itch S2 2 m dependent switch setting DIP switch 52 3 d c d VNV VUV VV ON data can be transmitted to the LCD DIP switch S2 3 OFF data cannot be transmitted to the LCD DIP switch
9. rmation on the minimum operating specifications in accordance with the Standards listed above tor defined immunity to interference 73 23 EEC Electrical equipment designed for use within certain voltage limits Applicable European Standards EN 60950 Safety of information technology equipment including electrical business equipment EN 61010 Safety requirements for electrical equipment for measurement control and aboratory use Part 1 General requirements If you use electrical equipment in installations and under ambient conditions requiring higher safety standards you must comply with the provisions as specified in the applicable regulations for installation in your country Sartorius AG amp 37070 Goettingen Germany amp Weender Landstrasse 94 108 37075 Goettingen Germany 449 551 308 0 4 49 551 308 32 89 Internet http www sartorius com Copyright by Sartorius AG Goettingen Germany All rights reserved No part of this publication may be reprinted or translated in any form or by any means without the prior written permission of Sartorius AG The status of the information specifications and illustrations in this manual is indicated by the date given below Sartorius AG reserves the right to make changes to the technology features specifications and design of the equipment without notice Status May 1997 Sartorius AG Goettingen Germany Printed in
Download Pdf Manuals
Related Search