Dokumentation - myIPE - IPETRONIK GmbH & Co. KG
Contents
1. Conflict at parallel access to the same resource A possible solution is the definition of module and channel settings NI DAQmx Plugin new IPETRONIK GmbH 8 Co KG ipetronik com 21 22 Explanations for some error messages IP TRON K 5 7 A svnchronization error in the acquisition of channel x occurred LE eil A svnchronization error in the acquisition of channel x occurred The sampling rate eventuallv does not correspond to the external timer If an external cycle source is used the sampling rate of the current module channel has to correspond to the cycle source frequency If they are not conform an asynchrony between the device and IPEmoOtion results and the time stamp of the values does not correspond to the expected times A possible solution is the exact customization of the sampling rate to the external cycle NI DAQmx Plugin new IPETRONIK GmbH 8 Co KG ipetronik com 22 222. KG ipetronik com 18 22 Devices BNC 6221 and BNC 6229 P TRON K 4 4 5 Initial value The initial value defines the value for counting start 4 4 6 Duty Cycle The duty cycle defines the relation between the logical status Example A duty cycle of 0 5 corresponds to 50 High level and 50 Low level according to the impulse duration 4 5 Hardware timed Digital Inputs Outputs E oe oe B X Project Signals Acquisition View Data manager Analysis Reporting NU N EY TOR LKE NI DAQmx DEL Le Detect Initialize Display Details S H Hardware Configuration Access View v01 01 00 Name Active Unit Phas Min Phy Kee Sur a Dev ijporti jined wi o Ei a W USB 6221 BNC 1 bii F Dev 1 port0 ine1 a ID Digital 0 Dev 1 port line2 0 io Counter 0 Dev 1 port0 line3 0 1 IN Analog In z Dev 1 port0 line4 o 1 3 e l a Dev 1 port0 lineS 0 1 g Digital Hardware Timed Dev 1 portO fines g i Dev Liport0Jine Il i General Extended timinq Timing tvpe External Cyde source ai SampleClock H 4 In contrast to the software timed digital inputs and outputs the hardware timed channels can access an external cycle source Timing by using the software timer is not possible By using the Extended timing tab you can define the following settings gt Timing type gt Cycle source gt Active edge 4 5 1 Timing type There are two different timing types available internal and external Internal timing uses the
3. LICENSEE will notify all of its employees agents or representatives permitted access to the SOFTWARE of the duties and obligations under this Software License Agreement d LICENSEE has the right to MODIFY the SOFTWARE for use on any internal computer or of EQUIPMENT as long as it is only on one computer or piece of EQUIPMENT at any given time e Any MODIFICATION S to the SOFTWARE are subject to the terms and conditions of this Agreement f LICENSEE may not i Loan rent lease give sublicense distribute transmit or otherwise transfer the SOFTWARE or otherwise exercise any of IPETRONIK s legal rights in and to the SOFTWARE or any derivative works of the SOFTWARE in whole or in part except with the prior written agreement of IPETRONIK li Copy translate reverse engineer decompile disassemble the SOFTWARE in whole or in part NI DAQmx Plugin new IPETRONIK GmbH 8 Co KG ipetronik com 5 22 Important and general information P TRON K iii Except as provided is Section 2 d create derivative works based on the SOFTWARE in whole or in part iv Remove modify or cause not to be displayed any copyright or trademark notices license agreements or startup messages contained in the programs or documentation v Transmit or otherwise export outside of the Unites States any of the SOFTWARE or technology in violation of United States or other applicable laws or regulations 3 Ownership of Intellectual Property LICE
4. frequency defined as sampling rate for generating the samples The cycle generation runs in the device itself External timing uses the device for generating the samples by using an external cycle Please note that the Sampling rate must correspond to the external cycle in order to avoid potential synchronization problems between the device and IPEmoOtion NI DAQmx Plugin new IPETRONIK GmbH 8 Co KG ipetronik com 19 22 Devices BNC 6221 and BNC 6229 P TRON K 4 5 2 Cycle source The hardware timed digital channels need an external cycle source because they do not have a timing unit In addition to the use of an external cycle source you can define the internal timers of the analog inputs and outputs as external timer for the counter The corresponding descriptions in the drop down menu are ai SampleClock for the analog inputs timer and ao SampleClock for the analog outputs The internal timer of the analog inputs and outputs can only be used as external cycle source if the channels are active This means that at least one channel of this type has to be active and the timer has to be started The usage of several analog timers at the same time is limited A maximum of four resources for every device can access the analog timer at one time The analog inputs and outputs are already included Using this limitation it is not relevant if the timer is one of the analog inputs or outputs Please note that the sampling rate must correspond to the e
5. is to reduce the sampling rate or the number of channels 5 3 General acquisition error or buffer overflow in one x channel Data storage has been stopped during acquisition due to missing valid data from the device This often results from a buffer overflow but can also have other reasons A detailed error description can be found in the send NI error code in the documentation of the NI DAQm x driver A possible solution is the selection of a lower sampling rate 5 4 The sampling rate is invalid The used software timer runs with a period duration For limiting the user in selection the sampling rate as less as possible no fixed values are given but any defined sampling rate is checked for validity Therefore the sampling rate must be selected for being converted into a period duration without decimal places Calculation Period duration 1000 Sampling rate A possible solution is the selection of a new sampling rate 5 5 Maximum 4 channels can operate as analog cycle source As already described in the chapters above a maximum of four resources can access the internal timer of the analog channels at one time otherwise a resource conflict can result A possible solution is the access limitation of the analog channels timer to four 5 6 The acquisition task for the channel type x cannot be started Channels are eventually used by several tasks at the same time You can find a detailed description of this limitation above under
6. 0 00 TA Analog In 24 Dev 1 port2 line1 si 0 00 DW Analog Out 4 Dev 1 port fline2 m 0 00 IO Digital Hardware Timed 32 Dev i port line3 S 0 00 In this example 2 USB devices are connected to the computer After detection both systems with complete channel overview are generated All the channels are grouped on signal type On device level in the Extended tab sheet the device serial number is indicated NI DAQmx Plugin new IPETRONIK GmbH 8 Co KG ipetronik com 10 22 Project ACQuskjon Vew N E p T Ve Ea d Svstem pon Adjust Detect Lon urabori Acess hey Ext Appnosl VO1 01 00 Name Active Unit Name gt 16 2 8 2 8 78 16 2 24 A A4 NI DAQmx Plugin new IPETRONIK GmbH 8 Co KG ipetronik com 11 22 3 Device 6501 3 1 Device Overview gt 24x digital I O lines gt 1x 32 bit counter 3 2 Digital oe ee X Project Signals Acquisition View Data manager Analysis Reporting Scripting Info NI NI RB A TO Sa pn Ei A NI DAQmx Check Adjust Detect Initialize Display Details CSV Importer Hard Configuration Access View Ext Appliciation H VO1 01 00 Name jA Unit Phys Min Phys Max 7 Sensor Min Sensor Max Sampling rate Name ge base 0 1 0 1 10 Hz 0 1 0 1 10 Hz 1 port0 line3 0 1 0 1 10 Hz 1 port0 line4 0 1 0 1 10 Hz 1 portO lineS 0 1 0 1 10 Hz 1 port0 line6 0 1 0 1 10 Hz 1 port0 ine7 0 1 0 1 10 Hz General Format Scaling Display Active v Name 1 port0 ine1 Description Digital I O channel
7. D i g i 10 Hz General Format Scaling Output Display Data type Type rr Task Default NoValue DefaultValue Value FullScale D Deactivate NoValue and use Default Value Channel type Input Output NI DAQmx Plugin new IPETRONIK GmbH 8 Co KG ipetronik com 20 22 Explanations for some error messages IP TRON K 5 Explanations for some error messages This chapter provides information about potential error messages and known behavioral patterns of the NI DAQmx Plugin 5 1 Conflict at parallel access to the same resource Different functions of a device sometimes use the same physical channel A counter which is defined as an output physically generates for instance its data on a Digital l O channel If the digital channel is defined as an input and the counter channel as an output a resource conflict occurs You should generally avoid multiple use of physical channels You can find the respective channel configuration in the data sheet of the corresponding module 5 2 Sampling rate of analog inputs too high The possible selection of the analog inputs outputs sampling rate depends on the number of active channels within a module Please note in general that the maximum sampling rate can only be selected according to 6 93 the maximum possible sampling rate divided by the active channel count in the module x indicates the maximum sampling rate which can be selected with the current configuration A possible solution
8. ID BY THE LICENSEE TO IPETRONIK FOR THE SOFTWARE c Since some states or jurisdictions do not permit the exclusion of implied warranties or limitation of liability for consequential damages in such states or jurisdictions the liability is limited to the fullest extent permitted by law 5 Intellectual Property Infringement Indemnification a IPETRONIK shall defend indemnify and hold LICENSEE harmless from and against any claims and fees including attorneys fees damage awards arising in connection with a claim that the licensed SOFTWARE or documentation when properly used infringes upon any presently existing valid and enforceable United States patent trademark or other intellectual oe right provided that such claim of infringement is not based on any Modification or action taken or suffered by LICENSEE other than the use of the licensed SOFTWARE and documentation in accordance with the terms and conditions of this agreement li such claim of infringement is not based on any action by LICENSEE in modifying the SOFTWARE pursuant to the terms of Section 2 d iii LICENSEE promptly notifies IPETRONIK of such claim in writing at supportOipetronik com and gives IPETRONIK exclusive control over the defense and settlement of such claim iv LICENSEE provides such cooperation and assistance at IPETRONIK S expense as IPETRONIK may reasonably request to settle or oppose any such claim and v such claim of infringement is base
9. IP TRONIK IP morton Software NI DAQmx Plugin September 2013 Table of contents Tapie 1 ta a i l 2 1 Important and general information eee aa EMMM nnmnnn nnmnnn nnmnnn mnnn 4 1 1 KEV URS Te AT ji gi tel UV ATV EE 4 1 1 1 Safety and Warning instructions cccccccccceeeeceeeeseeeeceeeeeeeeeeeeesaeeeeeeeessaaseeeeeseeaseeeessaaeeeeeessaeeeees 4 1 1 2 Liability Warranty Copyright License agreement rna 4 1 2 General information cccccccssssecccccseeeeceecceeeeceecseaueeeeeeseesseeeesaeueceeeseeaseceeessaaeeeeesssaaeeeeessaegeeeeessaaees 8 UE WE ie E L me A said ie in a a iet a a 8 12 2 AE 8 123 Legend of used ee 8 TZ SUPDOM ET 8 2 MPMI e TT H 2 1 NIl DAQmx driver installation ninni F HA AAAAAAEE EA AEEKAKAEENAEEEANEEEZNNENNNEEEZZZEEZZZA 9 2 2 FlUSIN ISTAM AMO ee E 10 2 3 PUP are de ee iri e Ke i l a a a ates seca eeeenta bagpecest aeseseeleeasest 10 3 Device O50 FG i i a E 12 3 1 Re e 12 3 2 Digital Inputs e A 12 3 3 COE MPU EE 13 A Devices BNC 6221and BNG 6229 iii i aaa aaa 14 4 1 Ries AAEE ednde Raa iatdednci tui Sasbtaacati teen n nnr een emenn 14 4 2 PNOO lo e DE 15 A a Analog Ru E EE 15 4 2 2 Extended Timing Tab 15 4 3 PROC US i ease E E EE E EE E E EE EN 16 4 3 1 Timing tab sheet mi a sj gene sss genie seu ahostecsuoandice cee ssecaqenaseeaiecoequdenedece 17 4 38 27 OVCE SOG ae ee l a a a E 17 ee EE 17 4 4 OCA TS NN eege 17 4 4 1 Mode Edge counting
10. ISED OF THE POSSIBILITY OF SUCH DAMAGES FURTHERMORE IPETRONIK S LIABILITY WHETHER IN CONTRACT TORT OR OTHERWISE ARISING OUT OF OR CONNECTED WITH THIS AGREEMENT OR THE LICENSED SOFTWARE OR DOCUMENTATION SHALL IN NO CASE EXCEED THE PAYMENTS RECEIVED BY IPETRONIK FROM LICENSEE FOR THE LICENSED SOFTWARE AND DOCUMENTATION EXCEPT IN CONNECTION WITH ITS OBLIGATIONS UNDER ARTICLE 5 i IN NO EVENT SHALL LICENSEE BE LIABLE FOR SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES INCLUDING WITHOUT LIMITATION LOST PROFITS LOST DATA OR LOST SAVINGS EVEN IF LICENSEE WAS ADVISED OF THE POSSIBILITY OF SUCH DAMAGES AND li LICENSEE SS LIABILITY WHETHER IN CONTRACT TORT OR OTHERWISE ARISING OUT OF OR CONNECTED WITH THIS AGREEMENT OR THE LICENSED SOFTWARE OR DOCUMENTATION SHALL IN NO CASE EXCEED THE PAYMENTS OWED TO LICENSOR FOR THE LICENSED SOFTWARE AND DOCUMENTATION 7 Indemnification Obligations of LICENSEE a LICENSEE shall defend indemnify and hold IPETRONIK harmless from any claims losses expenses fees including attorneys fees costs or damages arising in connection with a MODIFICATION or LICENSEE S unauthorized use of the Licensed Software or Documentation 8 Merger Clause a LICENSEE agrees that this Software License Agreement is the complete and exclusive agreement between LICENSEE and IPETRONIK governing the SOFTWARE This Software License Agreement supersedes and merges all prior agreements with IPETRONIK concerni
11. NED IN THE ABOVE AGREEMENT DURING INSTALLATION COPYING OR USING THIS PRODUCT IN ANY WAY YOU ACKNOWLEDGE THAT YOU HAVE READ THIS LICENSE AND THAT YOU UNDERSTAND AND EXPRESSLY AGREE TO BE BOUND BY THE TERMS AND CONDITIONS SET FORTH BELOW 1 Definitions a SOFTWARE is defined as computer program in object code or machine readable format together with any and all modifications enhancements updates and improvements provided by IPETRONIK as well as any subsequent versions corrections bug fixes enhancements updates or other modifications regardless of the source The term Licensed Software shall not include the source code version of the Licensed Software b EQUIPMENT is defined as automotive measuring equipment produced by IPETRONIK as well as other parties c LICENSEE is defined as the recipient of this SOFTWARE and any of its employees agents or representatives d MODIFY or MODIFICATION is defined as change to the SOFTWARE by LICENSEE in order to customize the SOFTWARE for use solely by LICENSEE 2 License Terms a As long as LICENSEE complies with all terms in this Software License Agreement IPETRONIK grants LICENSEE a non exclusive non transferable license to load and use the SOFTWARE upon the terms and conditions set forth below b LICENSEE has the right to load the SOFTWARE for use on any internal computer or piece of EQUIPMENT as long as it is only on one computer or piece of EQUIPMENT at any given time c
12. NSEE agrees and acknowledges that the SOFTWARE is being provided to it only for use in EQUIPMENT in the ordinary course of business and that LICENSEE agrees and acknowledges that IPETRONIK is the owner of all title and proprietary rights in the SOFTWARE including without limitation any and all patents copyrights trademarks or any other intellectual property rights associated with it under the laws of the United States or any jurisdiction throughout the world No right title or interest in the SOFTWARE or any IPETRONIK patent copyright trademark or any other intellectual property right is transferred to LICENSEE or any other party through this Software License Agreement 4 Disclaimer of Warranties Liability Limitations a THE SOFTWARE IS PROVIDED TO YOU AS IS THERE ARE NO WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND COMPATIBILITY AND TITLE b LICENSEE ASSUMES ALL RISK AS TO THE SELECTION USE PERFORMANCE AND QUALITY OF THE SOFTWARE IN NO EVENT WILL IPETRONIK OR ANY OTHER PARTY WHO HAS BEEN INVOLVED IN THE CREATION PRODUCTION OR DELIVERY OF THE SOFTWARE BE LIABLE FOR SPECIAL DIRECT INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING LOSS OF PROFITS OR INABILITY TO USE THE LICENSED MATERIAL IN NO EVENT SHALL IPETRONIK S LIABILITY FOR ANY DAMAGES OR LOSS TO LICENSEE OR TO ANY THIRD PARTY EXCEED ANY LICENSE FEE ACTUALLY PA
13. Pulse output ar AAKA EEA EEKAAAEEAEEnKEnEEEnEEEEEATI 18 A G VGIE SOUE rq i a eee er en ee Renee en O eee eee 18 4 4 3 EENEG 18 4 4 4 Counting direction a arsncdercd exnet 20s cacenacdnesanavenccataienect iinkenabiiduzaz tn tepo ateiiizaei ai akoneiddsa i tbiowinniieng iii heda 18 AA e EN 19 446 Duty Cycle ee 19 4 5 Hardware timed Digital Inputs Oumpute sse nnnnnnnnnn ann nanna nr rna KEnnnnnnnrnnnnEAEnnnEnnzEEzKEEEnAEEEZZ TA 19 NI DAQmx Plugin new IPETRONIK GmbH 8 Co KG ipetronik com 2 22 4S1 TIMIN ha e EE 19 4 09 20 OVCIE e 20 ADS Active le 20 5 Explanations for some error messages iii ok pr b ed 21 5 1 Conflict at parallel access to the same resource e esnnnnnnnnnnnnnn mnn nanna nn nnnnnr nanna ann rnnnnn nn nnnnnnta 21 5 2 Sampling rate of analog inputs too bgh arr rna AKEnnnEnAnEEEzAEAEnAEEENAEEEZEZA 21 5 3 General acquisition error or buffer overflow in one x channel 21 5 4 TAS sampling FATS H e resies ianen ka skur ian e kein bat REONE ERREEN EEE na ka a 21 5 5 Maximum 4 channels can operate as analog cycle source 21 5 6 The acquisition task for the channel type x cannot be starte 21 5 7 A synchronization error in the acquisition of Channel x occurred e enennnenznnnennnnnnnnnnnnnnnnn 22 NI DAQmx Plugin new IPETRONIK GmbH 8 Co KG ipetronik com 3 22 Important and general information P TRON K 1 Important and general information 1 1 Important information Please follow these inst
14. Reference The digital inputs and outputs are software timed channels i e the data is periodically sampled by using a software timer Analog to the software timed counter only sampling rates are accepted which can be converted into an even period duration 1000 Sampling rate gt The same sampling rate configured for one channel is automatically applied to all other digital inputs Defining Data direction gt The Format tab defines the channel type as an input or output This configuration defines whether the channel is operated as an input or output General Format Scaling Output Display Data type Type 1 5ii Task Default H NoValue DefaultValue Value FullScale _ Deactivate NoValue and use Default Value Channel type Input l Output v NI DAQmx Plugin new IPETRONIK GmbH 8 Co KG ipetronik com 12 22 3 3 Counter Input Project Signals Acquisition View Data manager Analysis N N i li b Ee d 4 L YE cs d i NI DAQmx System Component Export Check mi Detect Initialize Displa Hardware Configuration Access I vo1 01 00 Name Active Unit Phys Min General Format Scaling Display Counter I o The 6501 module supports only software timed counter The software timed counter uses a software timer based on the sampling rate for periodical data sampling Because of working with a period duration only sa
15. adapts to the required status 4 4 2 Cycle source In addition to the use of an external cycle source you have the ability to define the internal timers of the analog inputs and outputs as external timer for the counter The corresponding descriptions in the drop down menu are ai SampleClock for analog inputs timer and ao SampleClock for analog outputs The internal timer of analog inputs and outputs can only be used as external cycle source if the channels are active This means that at least one channel of this type has to be active and the timer has to be started The usage of several analog timers at the same time is limited A maximum of four resources for every device can access the analog timer at one time The analog inputs and outputs are already included Using this limitation it is not relevant if the timer is one of the analog inputs or outputs Please note that the sampling rate must correspond to the external cycle for avoiding potential synchronization problems between the device and IPEmotion Information l The external cycle source should not be mixed up with the event counter input The event counter input differs per device type and can be found in the corresponding device description 4 4 3 Active edge The active edge defines the time for sample generation 4 4 4 Counting direction The counting direction defines the upward and downward motion of the event counter NI DAQmx Plugin new IPETRONIK GmbH amp Co
16. d only on the licensed SOFTWARE and documentation as provided to LICENSEE b Inthe event of any infringement claim for which IPETRONIK is liable pursuant to section 5 a IPETRONIK may at its sole option and expense NI DAQmx Plugin new IPETRONIK GmbH 8 Co KG ipetronik com 6 22 Important and general information P TRON K I procure for LICENSEE the right to continue using the licensed SOFTWARE or documentation li modify or amend the licensed SOFTWARE or documentation so that it becomes non infringing iii replace the licensed SOFTWARE or documentation with a non infringing substitute or iv recover the infringing licensed software and documentation from LICENSEE and repay to LICENSEE all license fees paid to IPETRONIK in connection therewith less a reasonable amount based on LICENSEE s use prior to such recovery and refund This Article 5 sets forth IPETRONIK s sole obligations and liability for intellectual property infringement These indemnity provisions only apply to the SOFTWARE as originally licensed to LICENSEE and do not cover any MODIFICATIONS made by LICENSEE or any other third party 6 Limitation of Liability a EXCEPT WITH RESPECT TOITS INTELLECTUAL PROPERTY INDEMNIFICATION OBLIGATIONS AS SET FORTH IN ARTICLE 5 INNO EVENT SHALL IPETRONIK BE LIABLE FOR SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES INCLUDING WITHOUT LIMITATION LOST PROFITS LOST DATA OR LOST SAVINGS EVEN IF IPETRONIK WAS ADV
17. e device itself The second type of the external timing uses the device for generating the samples by using an external cycle Please note that the sampling rate must correspond to the external cycle for avoiding potential synchronization problems between the device and PEmotion 4 3 2 Cycle source The cycle source defines input and external timing 4 3 3 Active edge The active edge defines the time for generating the samples 4 4 Counter Channels Project Signals Acquisition View Data manager Analysis Reporting Scripting Info NI NE za AA LKA S NI DAQmx System i Check Adjust Detect Initialize Display CSV Importer Hardware Configuration Access View Ext Appliciation VO1 01 00 Name Active Unit Phys Min Phys Max Sensor Min Sensor Max Sampling rate Name ae LI 4 NI USB 6221 Zoe 1 S Devi ctri 0 4294967295 0 4294967295 1Hz T 0 me weg 0 2 Perap Out 0 IO Digital Hardware Ti 0 General Format Scaling Display Counter O Active Name Devi ctrO Description Reference Sampling rate 1kHz You generally have to distinguish between two different counter types Whereas the counter of the USB 6501 can only be used as a software timed module the counter of the USB 6221 BNC can use an external cycle source and therefore offers various definition possibilities The software timed counter uses a software timer based on the sampling rate for periodical sampling Each counter channel can use its own sa
18. fassung Benutzerdefiniert E Wahlen Sie die zu installierenden Komponenten aus dik o After installation and connection of the device to the computer the hardware is directly recognized in the Devices and Printer menu E ae a A a g f wg a alka b Systemsteuerung b Hardware und Sound Datei Bearbeiten Etras Ger t hinzuf gen Drucker hinzuf gen a Drucker und Faxger te 7 Pas Canon MG5300 Fax HP LaserJet 3390 series Printer 3392 PCLS 4 Ger te 3 ITO2 0293 Optical USB PL2409HD Mouse 4 Nicht angegeben 2 21 USB 6221 BNC USB 6229 BNC NI DAQmx Plugin new IPETRONIK GmbH 8 Co KG ipetronik com 9 22 namen IPETRONIK 2 2 Plugin installation The NI DAQm x Plugin is hosted on the IPETRONIK website www ipetronik com After having installed the Plugin you need to restart IPEmOtion A message window will notify you telling that a new Plugin was found After activation the Plugin can be used for data acquisition The Plugins can be managed in the options of IPEMOtION options l KEE Em IPEmotion options x jj Frequentlyused Jla iive Title Version Description Se ADDI DATA 01 00 00 14930 ADDI DATA Ethernet Devices Appearance ADVANTECH 01 00 00 27461 RC ADVANTECH bus coupler 01 02 00 BECKHOFF Bus Coupler 01 00 01 CAN Send with IPETRONIK CAN server 01 05 00 CAN Acquisition with IPETRONIK CAN Ser 01 03 00 14870 Se
19. icle s control units ECUs especially with such of the brake system and or of the engine and transmission control power train control system Installation of components for remote data transmission mobiles GSM GPRS modems WiFi and Bluetooth components 4 Before directly or indirectly using the data acquired by an IPETRONIK measurement system to calibrate control units please review the data regarding to plausibility 5 With regard to the application of IPETRONIK products in vehicles during use on public roads the manufacturer and or registered user of the vehicle has to ensure that all changes modifications have no influence concerning the license of the vehicle or its license of operation 6 User does agree to the instructions and regulations as mentioned above In case the user does not agree with the instructions and regulations as mentioned above he has to notify this expressly and immediately in writing to IPETRONIK before confirming the sales contract 1 1 2 Liability Warranty Copyright License agreement Limitation of liability Any liability of IPETRONIK its representatives agents and the like especially with regard to personal injury or damage to property of any kind shall be excluded within the legally admissible framework as far as the instructions and warnings aS mentioned below have not been followed Warranty Products accessories and services have a 24 months warranty All product data specificati
20. motion 1 2 2 Version This manual has the version number V01 released 09 2013 All rights reserved 1 1 2 3 Legend of used icons Q Tip This icon indicates a useful tip that facilitates the application of the software Information This icon indicates additional information for a better understanding d d K af AN Attention This icon indicates important information to avoid potential error messages 1 2 4 Support Headquarter IPETRONIK GmbH amp Co KG Im Rollfeld 28 76532 Baden Baden Germany Phone 49 7221 9922 0 Fax 49 7221 9922 100 info ipetronik com www ipetronik com Limited commercial partnership with its head office in Baden Baden registry court HRA No 201313 IPETRONIK Verwaltungs GmbH Baden Baden is an individually liable society registry court Mannheim HRB No 202089 CEOs Erich Rudolf Andreas Wocke Technical support and product information www ipetronik com e mail support ipetronik com NI DAQmx Plugin new IPETRONIK GmbH 8 Co KG ipetronik com 8 22 2 Plugin Overview 2 1 NIl DAQmx driver installation The Ni DAQmx Plugin requires the NI DAQm x driver library of National Instruments This library needs to be installed so that the devices are recognized correctiv via the USB interface The latest driver is hosted on the NI website The NI DAQmx device driver should be selected for installation ni com data acquisition ra NI DAQ mx 9 6 TreiberSoftware fur die Datener
21. mpling rate The settings are defined on the respective channel itself By using the Counter I O tab you can define the following settings Mode gt Cycle source gt Active edge gt Counting direction gt Initial value gt Duty Cycle NI DAQmx Plugin new IPETRONIK GmbH 8 Co KG ipetronik com 17 22 Devices BNC 6221 and BNC 6229 P TRON K General Format Scaling Display Counter I O Mode Edge counting Cycle source FEIS Active edge Falling edge z Initial value 0 Duty evde 0 5 4 4 1 Mode Edge counting Pulse output There are two different modes available edge counting and impulse sequence The first mode of Edge counting is a common event counter Since no possible internal cycle generation is available the counter depends on an external timer if it is not used as a software timed counter This cycle defines the frequency for generating and storing the samples The second mode Creating an impulse sequence uses the counter as output and an impulse sequence can be generated The sampling rate defines the frequency for generating an impulse sequence The duty cycle defines the relation between the logical status Example A duty cycle of 0 5 corresponds to 50 High level and 50 Low level according to the impulse duration The channel type in the Format tab does not have to be changed separately at Information changing between edge counting and generation of an impulse sequence because it automatically
22. mpling rates are accepted which can be converted into an even period duration 1000 Sampling rate The other boards like USB 6221 or 6229 can have external cycle sources which will be discussed in the following chapters NI DAQmx Plugin new IPETRONIK GmbH 8 Co KG ipetronik com 13 22 Devices BNC 6221 and BNC 6229 P TRON K 4 Devices BNC 6221 and BNC 6229 4 1 Device overview The channels in PEmotion are grouped in the same structure as on the board For example the USB BNC 6221 board has the following channel configuration gt 8x differential BNC analog inputs 16 bit 250 kS s gt 2x BNC analog outputs 16 bit 833 kS s b 8x BNC digital inputs hardware timed gt 16x BNC digital inputs gt 2x BNC 32 bit counters VO1 01 00 Name USB 6221 BNC 1 TA Digital Port1 amp 2 Counter Analog In Analog Out ta A Digital Hardware Timed Port i U MB M NI DAQmx Plugin new IPETRONIK GmbH 8 Co KG ipetronik com 14 22 Devices BNC 6221 and BNC 6229 P TRON K 4 2 Analog Inputs Project Signals Acquisition View Data manager Analysis NI N 3 Tt GC Ba ii HO i e GE Check Detect Initialize Displ i Hardware Configuration Access l vo1 01 00 Name Active Unit Phys Min Name SI a A 2 gt vi l 10 o oO l 10 10 2 10 i ra ta mi pe Y 10 General Analoginput Extended timing Circuit type Differential All analog inputs operate with the same sampli
23. ng the SOFTWARE and can only be modified by a subsequent written agreement signed by IPETRONIK To the extent that there is any conflict between this Software License Agreement and any IPETRONIK purchase order or other written agreement for the purchase of IPETRONIK parts or products the terms of the purchase order or written agreement control 9 General a If any provision or portion of a provision of this Software License Agreement is determined to be invalid or unenforceable it shall be deemed omitted and the remaining provisions of this software License Agreement shall remain in full force and effect to the fullest extent permitted by law LICENSEE may not assign or transfer all or part of this Software License Agreement to any third party without the express written approval of IPETRONIK NI DAQmx Plugin new IPETRONIK GmbH 8 Co KG ipetronik com 7 22 Important and general information P TRON K c This Software License Agreement will be governed by the laws of the State of Michigan without regard to its conflict of laws provisions d All disputes arising out of or in connection with the present contract shall be finally settled under the Rules of Arbitration of the International Chamber of Commerce by one or more arbitrators appointed in accordance with the said Rules 1 2 General information 1 2 1 About this manual This manual describes how to use the NI DAQmx Plugin to build your data acquisistion applciation with PE
24. ng rate When defined on one channel it is automatically udpated on all other channels count This results per channel from the maximum sampling rate divided by the O Please note that the maximum sampling rate depends on the active channel v Information channel are possible 4 2 1 Analog Input Tab channel count The more input channels are active the less sampling rates per Using the Analog input tab you can define the Circuit type The circuit type defines the type of grounding for the analog input channels A detailed description can be found in the documentation of the NI DAQmx driver 4 2 2 Extended Timing Tab By using the Extended timing tab you can define the following settings gt Timing type gt Cycle source gt Active edge General Analoginput Extended timing Timing type External IT E Cyde source PFIL3 z Active edge Rising edge zi NI DAQmx Plugin new IPETRONIK GmbH 8 Co KG ipetronik com 16 22 Devices BNC 6221 and BNC 6229 P TRON K There are two different timing types available internal and external The first type of the internal timing uses the frequency defined as sampling rate for generating the samples The cycle generation runs in the device itself The second type of the external timing uses the device for generating the samples by using an external cycle Please note that the sampling rate of the inputs must correspond to the external cycle for avoiding potential synchro
25. nization problems between the device and PEmotion The cycle source defines the input where the external timing signal is coming from The active edge defines the time for generating the samples based on a rising edge or falling edge 4 3 Analog Outputs LS ck Project Signals Acquisition View Data manager Analysis Ru NI N B tTa NSO NI DAQmx System Components Exp Check EE Detect Initialize Display Hardware Configuration Access VO1 01 00 Name JActive Unit Phys Min Name gt OI a HI USB 6221 ENJA 1 4 ID Digital 0 Counter 0 TE TI General Extended timing Timing type internal i Cyde source PF IO Active edge R sing edge All analog inputs operate with the same sampling rate When defined on one channel it is automatically udpated on all other channels Please note that the maximum sampling rate depends on the active channel count This results per channel from the maximum sampling rate divided by the channel count The more input channels are active the less sampling rates per channel are possible Information NI DAQmx Plugin new IPETRONIK GmbH 8 Co KG ipetronik com 16 22 Devices BNC 6221 and BNC 6229 P TRON K 4 3 1 Timing tab sheet There are two different timing types available internal and external The first type of the internal timing uses the frequency defined as sampling rate for generating the samples The cycle generation runs in th
26. ons drawings etc correspond to the current condition of the indicated creation date For the purpose of optimizing technical processes and production some details of our modules and accessory components may be modified at any time without prior notification Although the present document has been prepared with the utmost attention to detail it may not be exempt of misprints typing or transcription errors These errors are not covered by any warranty NI DAQmx Plugin new IPETRONIK GmbH 8 Co KG ipetronik com 4 22 Important and general information P TRON K Copyright and Duplication All rights reserved to IPETRONIK GmbH amp Co KG in particular those of property copyright and trademarks The rights related to any third party trademarks mentioned in the present document remain unaffected This document may not be duplicated partially or entirely without the prior approval from IPETRONIK GmbH amp Co KG All graphics and explanations are copyright protected Any use beyond the scope of the document is prohibited Software license agreement This software is property of IPETRONIK GmbH amp Co KG and is protected by copyright laws Its total or partial reproduction is strictly forbidden A valid software license is required to use the software IMPORTANT READ CAREFULLY THIS IS A LEGAL AGREEMENT BETWEEN YOU LICENSEE AND IPETRONIK GMBH 8 CO KG IPETRONIK INC IPETRONIK BY CHECKING I ACCEPT ALL OF THE TERMS CONTAI
27. rial interface for GPS mouse Connecting NI DAQmx devices 01 02 00 Access to process data of Siemens PLCs 01 00 04 28250 Synchronic recording of video data for ca 01 01 00 31598 RC WAGO Bus coupler 01 01 03 CAN protocol acquisition with any CAN ha Download Plugin settings A Specify the plugins to be used The used plugin version can be changed within the list If a version number is selected that ends with a character no automatic update is run at installing later plugin versions e OK Cancel 2 3 Hardware detection IPEmOtION provides functions for automatic hardware detection Setting up communication between board and USB devices like the NI DAQmx family is very easy using automatic hardware detection Project Signals Acquisition View Data manager Analysis Reporting 5 N BITOMHBOE Export Check Detect nitialize Display Details CSV Importer Configuration Access View Ext Appliciation VQ1 01 00 Name Create a new hardware configuration with the devices This function does not only apply to the modules shown in systems but to all found hardware of all connected hardware USB 6221 E e T Digital 16 Devijportijine2 wi 0 00 Counter 2 Devijportijinez w 0 00 IN Analogin 8 Dev 1 port1line4 7 0 00 teg l Devijportijines 7 0 00 IO Digital Hardware Timed 8 _ Dev 1 port1 line si 0 00 a WI USB 6229 BNC 2 78 D Digital ei Devijportijine7 wi 0 00 T Daie 2 Dev 1 port lined Da
28. ructions before and during the use and application on any IPETRONIK product 1 1 1 Safety and Warning instructions Please follow the instructions and information as contained in the user manual 1 The user can influence an electronic system by applying the IPETRONIK product This might cause risk of personal injury or property damages 2 The use and application of the IPETRONIK product is permitted only to qualified professional staff as well as only in appropriate manner and in the designated use 3 Before using an IPETRONIK measurement system in the vehicle it has to be verified that no function of the vehicle which is relevant for secure operation might be influenced by the installation of the IPETRONIK measurement system in the vehicle by an potential malfunction of the IPETRONIK system during the test drive In order to avoid possible danger or personal injury and property damages appropriate actions are to be taken such actions have to bring the entire system into a secured condition e g by using a system for emergency stop an emergency operation monitoring of critical values Please check the following points to avoid errors Adaption of sensors to components of the electrical system electronics brake system engine and transmission control chassis body Tap of one or several bus systems CAN LIN ETHERNET including the required electrical connection s for data acquisition Communication with the veh
29. xternal cycle in order to avoid potential synchronization problems between the device and IPEmotion Information l The external cycle source should not be mixed up with the event counter input The event counter input differs per device type and can be found in the corresponding device description 4 5 3 Active edge The active edge defines the time for generating the samples gt The same sampling rate is configured for one channel and is automatically applied to all other digital inputs Defining data direction gt The Format tab defines the channel type as an input or output Over this configuration it is defined whether the channel is operated as an input or output o PB fC AE X a 3 P IPEmotion Project Signals Acquisition View Data manager Analysis Reporting Scripting Info b tt t N NA e 4 NI DAQmx System Components Impe Export Check EE Detect Initialize Display Details CSV Importer 7 kl Hardware Configuration Access View Ext Application VO1 01 00 Name Active Unit Phys Min Phys Max Sensor Min Sasor Max Sampling rate Name gt T m ag Dev 1 porti jined vi H 1 0 1 LO Hz a NI USB 6221 BNC 1 6 Dev 1 port0jline1 w o i l i 10 Hz ID Digital 0 Dev 1 port0 line2 l i o 1 10 Hz OD Counter o Dev 1 port line3 o 1 a 1 10 Hz IN Analog In z Devijportd red 0 i o i 10 Hz a Gene Vie el 2 Devijporti jine5 D i o i 10 Hz Di lu fare Timed E See i een Dew 1 port0 lined 0 1 0 i 10 Hz Dev L port dine 7
Download Pdf Manuals
Related Search