Manual iPhone App
Contents
1. Industries Ka Controller Login Roth UID 56FF73064889485X000000X Unique ID Number needed in case password user name is lost Password 1234 NEN gt Type in the default password 1234 COMETA GE ET Press Reset Password Please Change your Password Type in your user name and password in consideration of the following con ditions A e The user name must be at least between 3 characters and not more than 18 ke Controller Login characters long e The user name first character must be a letter or digit e The user name cannot contain any spaces punctuation marks or special User Nimes characters ae etc e The user name can contain underscores periods and hyphens e The password must be at least between 4 characters and not more than 16 characters long e The password cannot contain spaces punctuation or special characters Old Password New Password Confirm Password Registration on Portal O Select Registration on Portal on SR Press Submit to connect the Controller to the Portal Message field that shows the following results e Connecting to Portal e Invalid user name or Invalid password Roth Industries p Violation of the name password conditions above please change Controller Login e User name already used or Password already used Chosen name password defined by other user in Portal before User Name MyUserName please change Old Pass2. UID of your iPhone is shown at the top e Send this UID to the following e mail Touchline PW reset Roth industries com You Will receive a reset code to reset the password to de fault value e Press Reset Password leave the field Password blank Roth Industries oo oniroiier ogin I Mon na e Type in the reset code and press Reset Password button Katie The password is reset to default settings 1234 UID 56FF6D064889485750262387 e hen change your password as described on page 8 and make a Password new registration on the portal server It is possible to use your pre vious password Reset Password Reset Code P100011302 A 17 iPhone Manual Roth EnergyLogic Touchline er i Problem solving 6 2 Problems with GSM connection The speed of the data transmission is depending on the connection strength when using the iPhone GSM connection Roth Industries lt OK Weak lost Roth Industries Main Main Weak or interrupted signal during a session is indicated with a small red rectangle as shown in the right picture E Rooms For a proper control of the system online the GSM signal should be at least one beam Mode gt Mode T Config T Config 11 35 02 09 2011 11 35 02 09 2011 18 P100011302 A Roth iPhone Manual Roth EnergyLogic Touchline Problem solving 6 3 Controller not found If the controller cannot be found please do t
3. 2 22 1 C Bath 24 1 C Cellar 19 3 C Page 1 from 2 next Start gt Rooms e actual room temperatures e clock symbol showing that a time program is active Roth Industries Mode a Active Day Night Off Holiday No Error om CJI DO 5 O Start Rooms Mode Config Start gt Mode Change mode of all room thermostats complete system e Select the mode iPhone Manual Roth EnergyLogic Touchline Roth Industries ke Livingroom Roth 21 0 C Actual Temperature Temp setpoint Status Program Lei ke Ed Rooms Mode Config Info Start gt Rooms gt Room Details e change setpoint e change mode of operation e change time program Roth Industries Mode Info Use setting DAY for all operating room units Activated time programs and subsequent changes to the room control unit itself have priority Cancel Start Rooms Mode Config Info Start Mode Confirm Note local time programs have a higher priority and need to be deac tivated if change is permanently wanted for all room thermostats See also FAQs Operation Roth Industries dem Livingroom Roth 21 5 C Set temperature Start gt Rooms gt Room Details gt Change value e Increase press up e Decrease press down P100011302 A 15 iPhone Manual Roth EnergyLogic Touchline Operation Roth Industries Mode a Active Day Night Off Holiday et
4. 2 can also be found at the info pages of your iPhone Info Dear customer Many thanks for your investment in the new Roth Touchline Control system and the Touchline APP To use the features of the APP the complete system must be set up and all room thermostats must be paired in the system If you have more than one controller a master controller must be defined and the slave controller s have to be paired to it Please use the system s handbook for the specific setup Hore is what you have to do step by step 1 Press the Config button in the main menu You will now see all the room thermostats which have been paired to the complete system next gt P100011302 A 13 iPhone Manual Roth EnergyLogic Touchline Operation f 5 3 Operation Activate the App Roth Industries Roth Industries Touchline EnergyLogic ouchline EnergyLogic Search for new controller gt Connect controller Select language gt Connect controller gt Roth Industries Main Rooms gt View all rooms Mode gt Change mode of all rooms T Config Configuration of room names 11 35 02 09 2011 Roth Industries Ro Touchline EnergyLogic MyUserName Password Connect via Internet Logon Logon with password select Internet or WLAN to enter 14 P100011302 A Roth Industries Rooms mM Ha 23 7 C D Livingroom Bedroom 1 21 9 C Bedroom
5. Energy systems Control system EnergyLogic Wireless control Touchline Trea Bedroom 1 User manual iPhone App Bedroom 2 Bath Cellar D O O Mi AUTO C T CL LEE B 8 5 B Les L3 a NL LE E g e vest D HS ne 8 8 M O O O D D 0 ooon i e LG GH ZC j p ee KI d hs s ooo 0 0 0 0 0 ooon NEU U 88 884000 D wees ps Living full of energy Roth UK Ltd Taunton Somerset TA4 2 RL Telephone 44 0 19 84 62 39 82 Telephone 44 0 19 84 62 39 15 E Mail sales roth uk com www roth uk com Revision number A Revision date July 2013 i P100011302 A LH I iPhone Manual Roth EnergyLogic Touchline LIT Table of content Table of content WD Va d Le e e ro MP 4 2 Connect Master Controller to WLAN Router 5 5s BOWHlloOdU ADD EE 6 4 Network Configuration using the WLAN Network 6 MEE 10 Os e 9 EE 10 5 2 Configure names for all wireless room thermostats 12 o MEE Go rufo BEE 14 6 Problem Ee Lu e 17 OL Passwords TE 17 6 2 Problems with GSM connection 18 6 3 Controller not found 19 6A FAQS ee eee ee eee ee eee 20 P100011302 A 3 iPhone Manual Roth En
6. N 2 nei Jr O Start Rooms Mode Config Info Start gt Mode Menu mode when alarm active e Press error to see alarm details Roth Industries Config ID 253 1 Livingroom ID 242 1 N N ID 242 2 N N ID 242 3 N N ID 242 4 N N System Info Start gt Config Giving names to room thermostats 16 f Roth Industries Error RF Communication Interrupted Check room units lt E gt ke 1 Il d dj KE Rooms Mode Config Info Start Mode Error Possible alarms e RF communication interrupted e High limit dewpoint e High limit supply water Will only occur if a supply water high limit safety thermostat is in stalled See user manual parameter P 62 Roth Industries System Info DEO ge a Mode Config o Start gt Config gt System Info Overview installed system P100011302 A Fr iPhone Manual Roth EnergyLogic Touchline Problem solving 6 Problem solving 6 1 Password lost Roth Industries In case you have lost your password you have to do the following oniroiier ogin D D gieren e Find the Unique ID number UID of your iPhone by the following procedure MyUserName UID 56FF6D064889485750262387 Be sure that the connection between iPhone and controller Password goes through WLAN L Activate the App Reset Password Select your language Select Search new controller Press the found controller The
7. charged with a one time fee any future updates are free of charge 4 Network Configuration using the WLAN Network The master controller is connected to the WLAN router and the App is in stalled on the iPhone Open the settings menu of your iPhone by pushing Ka Airplane Mode Ka Wi Fi Your Network gt gt Select Wi Fi settings K Carrier F SFR gt k Notifications On gt bi Sounds EX Brightness ig Wallpaper Kg General Select Wi Fi ON Choose a Network V Your Network a P Select your network Other Ask to Join Networks ET Known networks will be joined automatically If no known networks are available you will be asked before joining a new network gt Start the App on your iPhone by pushing the Roth Touchline icon 6 P100011302 A iPhone Manual Roth EnergyLogic Touchline Network Configuration using the WLAN Network ouchline EnergyLogic Select your language Touchline EnergyLogic Search for new controller gt gt Push Search for new controller Connect controller Roth Industries dim Found controllers Scanning ID 253 ROTH E77F4B The Roth Master Controller connected to the WLAN network is listed Select the controller If the controller could not be found please check chapter 6 3 P100011302 A T iPhone Manual Roth EnergyLogic Touchline Roth Network Configuration using the WLAN Network m l i Roth
8. de to reset the password to default values For further details see section 6 1 P100011302 A 9 iPhone Manual Roth EnergyLogic Touchline Fa I I Operation C ER 5 Operation All wireless room thermostats are addressed to the controller s and if there is more than one con troller the slave controllers must be addressed to the master The WLAN connection is made in ac cordance to Chapter 2 the App is activated in accordance with Chapter 3 and the network is config ured in accordance with Chapter 4 5 1 Logon Activate the App ouchline EnergyLogic Select your language Roth Touchline EnergyLogic Search for new controller gt Connect controller gt Select Connect controller 10 P100011302 A iPhone Manual Roth EnergyLogic Touchline Operation Touchline EnergyLogic MyUserName Enter your password Password Connect via Press Internet or WLAN Internet The Start screen is shown your log on was successful Rooms J O Mode T Config 11 35 02 09 2011 If the Language screen is shown again then you have entered the wrong password Please try again If you have lost your password please follow the instructions as defined in section 6 x ouchline EnergyLogic P100011302 A 11 iPhone Manual Roth EnergyLogic Touchline Operation f 5 2 Configure names for all wireless room thermostats D Raih Industries Main Rooms M
9. ergyLogic Touchline Re Introduction 1 Introduction The iPhone connection to the Roth EnergyLogic Touchline control system enables remote access with full operational control of the system Once in stalled it is possible to read actual temperatures to change setpoints and to check and change the mode of operation of each individual wireless room thermostat In addition it is possible to change the mode of operation of the entire system with just one touch The iPhone App can be used for iPhone iPad and iPod touch For the iPod touch however only within a WLAN network System topology The iPhone can be connected to a home network by using a WLAN router In addition it is possible to access the system via Internet by using the Roth portal server The use of a WLAN router is obligatory in order to set up the system Controller RF Network m Pi sa 228 w ul Bu d l S on eene a ea Slave Controller 2 Room Control RF Network Slave 2 N iPhone through I gt we the Internet Ss fie Portal Server E d RB m ww Slave Controller 1 Room Control RF Network Slave 1 iPhone in I mn Wf we I Home Network l H N P ES d 7 ve DSL Router WLAN Router Master Controller Room Control RF Network Master Fig 1 Topology wireless connection module s with iPhone If the home network doesn t comprise a WLAN router it is possible to in stall a WLAN rou
10. he following Check if the controller is set as Master Check the network installation in accordance with section 2 Check the LAN cables used Check the power connection to the WLAN router Please switch off the power of the WLAN router and switch on again Check the power connection to the controller Check the WLAN connection with your iPhone Check if a mini SD card is installed in the controller Check if the mini SD card is completely inserted into the controller o Warning switch off the power of the controller before removing or installing the SD card Check if the mini SD card is readable o Switch off the controller o Remove the mini SD card by pushing it into the controller o Use a mini SD card adapter and connect this adapter to a PC o Use Windows Explorer to see if the files are visible Attention do not open move or delete any files o lffiles are not visible visit the Roth web site to find the instructions to format the mini SD card and to download a new set of files fthis doesn t work please purchase a new mini SD card o Prepare the mini SD card in accordance to the instructions on the Roth web site o Insert the mini SD card into the controller o Connect power to the controller o Wait approx one minute until the controller is rebooted LED s are flashing rapidly during this process o Try again to find a new controller P100011302 A 19 iPhone Manual Roth EnergyLogic Touchline er i Problem solv
11. ing 6 4 FAQs Q All room thermostats show an actual temperature of 21 0 C A After a power interruption or at the first start up the controller has default values of 21 C for all actual room temperatures It will take 10 to 13 minutes before all temperatures are updated Q It is not possible to build up the connection by GSM After log on the Select Language page appears again A The following could be valid e Wrong password please check e GSM connection too weak please wait for a better signal at least one beam e Internet connection of the WLAN router is not active e Power interruption of the controller WLAN router or ADSL router Q All thermostats are set to the same mode with the central mode function but after a while one or more rooms are in another mode A Local operation at the room thermostats has higher priority than operation by iPhone Hence ei ther somebody has changed the mode at home or a time program is still active One or more time programs are still active if the clock symbol is shown on the Mode page Deactivate all time programs visible at the Rooms page and then select the desired central mode again Q Notall room thermostats are set to the same mode immediately by the central mode func tion A All room thermostats connected to the master controller are set immediately to the desired mode For room thermostats connected to slave controllers it can take up to 3 minutes before they a
12. ode yk Config 11 35 02 09 2011 Roth Industries Config ID 253 1 ID 242 1 ID 242 2 ID 242 3 ID 242 4 System Info Roth Industries Config ID 253 1 Livingroom ID 242 1 N N ID 242 2 N N ID 242 3 N N ID 242 4 N N System Info You are logged in and the Start screen is shown gt Press the Config button in the main menu You will now see all the room thermostats which have been paired to the complete system In each line you see an ID no for 1 Display in stand by mode 2 Sensor buttons example 253 1 253 for controller 1 for a menu thermostat followed by N N no name b ok You now need to identify the room thermo c escape stats and name them one by one so you will easily recognize which room you are looking at Fig 3 Room Thermostat Go to the first room thermostat and do the following look at fig 3 to follow The room thermostat shows the standby mode gt Press one of the sensor buttons for more than 2 seconds to activate The thermostat now switches to operating mode The set point temperature is flashing gt Press the sensor button menu for 5 seconds The display shows P01 Press the sensor button menu several times to choose the parameter P08 Show ID number of the room thermostat Press the sensor button OK In the display the ID number can be seen Note the ID number of the thermostat for example 03 Press the sensor bu
13. re set to the desired mode For more information please see www roth industries de qr touchline htm 20 P100011302 A
14. ter temporarily until the system using the portal server is set up After that the WLAN router can be removed again and the master wireless connection module is connected directly to the DSL router All communication will be done by Internet 4 P100011302 A iPhone Manual Roth EnergyLogic Touchline M Connect Master Controller to WLAN Router 2 Connect Master Controller to WLAN Router In order to connect the iPhone to the controller the master wireless connec tion module must be connected first to a WLAN router The WLAN router can only be connected to a master controller A master controller can be identified by the master LED must be on In a system with two or three controllers there is always a master controller If only one controller is installed it is possible that this controller is not set as master To set this controller as master push the master button 10 sec onds For further details please read the User Manual Touchline Switch off master controller Connect the master controller to the WLAN router in accordance with figure 1 section 3 Switch on master controller LAN Options 1 PowerLAN B12237 Fig 2 LAN Verbindung P100011302 A 5 iPhone Manual Roth EnergyLogic Touchline Fd I Download App h C 3 Download App The Roth Touchline App can be downloaded from the App store at your iPhone Please note that this is not a free download your iTunes account will be
15. tton OK P 09 is shown in the display Show ID Number of the controller Press the sensor button OK In the display the ID number can be seen Note the ID number of the controller for example 253 only needed if you have more than one controller Find the ID numbers of respectively the controller and the thermostat in the overview of the Config page in the APP for example 253 03 p Press on the field with the name N N and type the name of the room you want for example Living room Press the sensor button Esc to leave the menu of the thermostat The display shows the operating mode and the set point temperature is flashing Repeat the above operation for all room thermostats which are paired in the system If there are more wireless room thermostats than listed press next 12 P100011302 A Fr iPhone Manual Roth EnergyLogic Touchline Operation Roth Industries Config ID 253 1 Livingroom ID 242 1 Bedroom 1 p ID 242 2 Bedroom 2 a ID 242 3 Bath 5 ID 242 4 Cellar System Info gt D Press System Info of the Config menu to overview the entire system Roth Industries System Info In this example the system consists of 5 room thermostats addressed to in total 2 controllers The Master controller is always shown in first upper position and the next will be Slave 1 and Slave 2 p Press Info Config Roh Industrias The procedure as defined in this section 5
16. word e Failed connecting the Portal New Password Please check if your iPhone has Internet access Confirm Password e Registration on Portal done Registration on Portal EM Submit Registration on Portal done 8 P100011302 A iPhone Manual Roth EnergyLogic Touchline f Network Configuration using the WLAN Network Roth Industries ler Login Ro Press arrow back to leave the connecting to the portal procedure MyUserName UID 56FF73064889485743362287 Password L v Change User Name Password Connected to Portal y You are now able to enter the App either through WLAN or the Internet Roth Touchline EnergyLogic MyUserName Password gt Enter Password Connect via Internet gt Select Internet or WLAN If App failed connecting the Portal please check Internet connection using the Internet browser of your iPhone that is connected to your WLAN net Work As long as your iPhone is within the WLAN network the WLAN network will be always chosen When this connection is lost and your Phone has Internet access then the connection will be built up through the portal server If the user name and password are lost you need to identify the unique ID number of your iPhone This unique ID number can be found as described in section 6 1 Then you have to send this unique ID to Roth by e mail Upon receipt of your mail Roth will send you a reset co
Download Pdf Manuals
Related Search