RACK-250 CHASSIS USER`S MANUAL
Contents
1. 66612 innu TES EHHHHHHHHUH E 20061 e B 30 iL BE 22222222 000 g S 8006 UNIT mm EXPLODED DIAGRAM APPENDIX B 172. 12255 90900000002299 00 2200000 00000 8800 RESET SWITCH POWER LED POWER SWITCH 2 2 LP 01 Control Panel of 250 Rack 250 is equipped with LP 01 control board Please refer to the following figure as you set up your system LES Poe POWER LED GREEN HDD LED RED 12345678 Pin NOTE 1 2 PIN BUZZER 3 4 PIN POWER LED GREEN 5 6 PIN HDD LED RED 7 8 PIN RESET SWITCH LP 01 Panel BZ1 BUZZER D1 POWER LED D2 System HDD LED SW1 RST system reset button CN1 FUNCTION SPEAKER SPEAKER ___ 7 RESET 2 O O O O O o O 2 3 Rear Panel of RACK 250 Please refer to the following diagram which illustrates the equipment of the rear panel SS 2A 9 gt 2 0 96 ae gt AGING IE VGA Port LINE OUT Printer Port LINE IN COM1 COM2 MIC MOUSE 10 100 Base T PORT Ethernet NETWORK LED EXT K B 2 USB Port 2 4 Removing the chassis cover The cover is mounted by some screws on the top of the chassis Hence you can remove the screws and open the cover of chassis directly Figure below shows how to remove the chassis cover 2 5 Multimedia POS Control Board Installation Figure below illustrates how to install the POS Control Board on the RACK 25
3. 0 2 6 Disk Drives Installation 10 1 Open the upper disk drive cover 2 Fix the HDD and FDD into bracket and then install them into the chassis 3 Connect the necessary cables 2 7 Replacing the Filter Just The filter should be removed and cleaned at least once a month to achieve optimum performance The filter of the RACK 250 is located at the front end of the chassis replace it with the new one if its already worn out 12 2 8 Power Supply Installation Please refer to the figure below to install the Power Supply mt e gt CEST x 55 gt lt 8 8 5 2 lt S o vo 2 5 gt E lt 5 m 2 13 2 9 Fan Installation The following diagram is provided for your reference as you install the Fan and connect to the Power Supply SUPPLY POWER SA o f SS Sh M e OS DDIN lie SUN AS Q 6 N 14 2 10 Power and Control Board Cable Connecting Please refer to the following diagrams to connect the cables to the Control Board POS 566 Control Board ACE 890A POS 566 Control Board IP 52 15 PASSIVE CONTROL BOARD APPENDIX A
4. One 3 5 FDD and One 3 5 HDD drive space Cooling Fan Dual Ball bearing fans Indicator Two LEDs to monitor the status of HDD and Power Supply Dimension 484x412x44 WxDxH Power Supply Standard equipped power supply for the RACK 250 is ACE 890A 9OW Optional ACE 890P 70V 132VDC input power supply ACE 890T 36V 72VDC input power supply ACE 890C 18V 36VDC input power supply ACE 890V 9V 16VDC input power supply Working Environment Operating Temperature 0 50 Relative Humidity 595 Relative humidity Vibration 5 17Hz 0 1 double amplitude displacement 17 640Hz 1 5G acceleration peak to peak Shock 10G acceleration peak to peak Safety approval meet CE FCC Cooling Fan Dual rear ball bearing cooling fans for optimum system cooling Drive Capacity One 3 5 FDD and one 3 5 HDD drive space imensions 1 3 D 484mm x 44mm x 412mm WxHxD i 021 N A 4 06 5x10 0B UNIT mm 431 0 466 0 484 0 09 Chapter 2 Installation Procedure The following procedure is provided to assist you in installing the system please follow the steps below 2 1 Front Panel of RACK 250 The front panel is equipped with Power Switch Reset Switch Power LED and HDD LED as the following diagram shown
5. RACK 250 CHASSIS USER S MANUAL Copyright Notice This document and product is copyrighted Jun 1999 by ICP Electronics Inc All rights are reserved No part of this manual may be reproduced copied or translated without prior notice to ICP Electronics Inc The information provided in this document is for reference only We do not assume any responsibility arising out of the application of the products This manual is subject to change without any notice RACK 250 and ICP are trademark of ICP Electronics Inc Table of Contents Chapter 1 Product Information 1 1 General Information 1 2 Product Specifications 1 3 Dimensions Chapter 2 System Setup 2 1 Front Panel of RACK 250 2 2 LP 01 Control Panel of RACK 250 2 3 Rear Panel of RACK 250 2 4 Removing the chassis cover 2 5 Multimedia POS Control Board Installation 2 6 Disk Drives Installation 2 7 Replacing the Filter 2 8 Power Supply Installation 2 9 Fan Installation 2 10 Power and Control Board Cable Connecting Appendix A Passive Control Board Appendix B Exploded Diagram Chapter 1 Product Information 1 1 General Information RACK 250 IPC chassis is a rugged PC AT compatible computer designed for the factory floor and other Industrial harsh environment RACK 250 is designed for POS 566 POS Control Board and standard equipped with ACE 890 series power supply 1 2 Product Specifications General specification Construction Heavy duty steel Disk Driver
Download Pdf Manuals
Related Search