LM6100 Series LCD Monitor
Contents
1. When this item is selected there will be only the OSD time icon with an adjustment indication bar under it between the main menu area and the video signal mode Press or POSIFLEX button to adjust the waiting time for OSD operation before OSD termination between 5 to 60 seconds Default is 30 seconds Press OSD button to save the current setting and return to OSD submenu OSD HORIZONTAL POSITION When this item is selected there will be only the vertical position icon with an adjustment indication bar under it between the main menu area and the video signal mode Press button to shift OSD window right Press to shift left Press OSD button to save the current setting and return to OSD submenu OSD VERTICAL POSITION When this item is selected there will be only the vertical position icon with an adjustment indication bar under it between the main menu area and the video signal mode Press button to move OSD window downward 6699 Press to go upward Press OSD button to save the current setting and return to OSD submenu g EXIT Return to Tools submenu mE RESET TO DEFAULT Pressing OSD button on this icon will set all parameters back to the status when the monitor left factory SMOOTHNESS SHARPNESS ADJUST When this item is selected there will be only the smoothness sharpness adjust icon with an adjustment indicatio2. these four screws holes which are in the back of monitor as A in the right picture Note Please DO NOT fasten these screws to the end at first time rotates The best way is rotate about 2 3 circles 2 Take the bracket and aim the four matching holes to these four rotated screws Then push the bracket as arrowed direction in picture B at right 3 After push the bracket to the end of winding slot please fasten the screws which are just rotated at step 1 as showing on the picture C POSIFLEX V OSD A OSD buttons OSD button To enter OSD setup menu or to perform function selected in OSD operation NXT button To go to next option function button To increase setting button To decrease setting button To turn the monitor power ON OFF The monitor can be turned OFF only when there is video signal and can be turned ON only when there is video signal and after the Turn Off Panel message vanishes The default status is set to ON when power is supplied unless manually turned OFF Since this button controls only the display power but not the display controller please try disconnect the power cable or the VGA cable once unfortunately the screen display goes into a mess B OSD functions Press OSD button with a normal display on the screen to activate the OSD functions On Screen Display adjustment The OSD window will pop up on the screen On to
3. POSIFLEX LM6100 Series LCD Monitor USER S MANUAL Rev B l FEATURES E e Light weight and high luminance LCD monitor for industrial and commercial use e Application covers POS POIS Kiosk Factory Automation etc e High quality 12 1 TFT LCD panel with scaling up function for full screen display e Successor from earlier LM6000 series and supports display resolution up to 1024 x 768 pixels e Tilt and swivel adjustable construction e Spill proof and easy maintenance structure allowing easy cleaning e Wall mount bracket with 75mm VESA standard FCC NOTICE This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual may cause interference to radio communications It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules which are designed to provide reasonable protection against interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct the interference WARRANTY LIMITS Warranty will terminate automatically when the machine is opened by any person other than the authorized technicians The user should consult his her dealer for the problem happened Warranty voids if the user does not follow the instru
4. ance to a color temperature of 9300 degrees Kelvin EI EXIT Return to Color adjust submenu E EXIT Return to Main menu KY GEOMETRY ADJUST SUBMENU There are 6 icons in this submenu HovrvesSsi Press OSD button to select item or return to main menu Press NXT button to select among auto geometry adjust horizontal size phase horizontal position vertical position and exit AUTO GEOMETRY ADJUST Upon an OSD button press on this icon the monitor will perform an automatic geometry adjustment and exits the OSD window leaving 2 icons below at center of the screen Press NXT button to switch the selection Press OSD button to make the choice POSIFLEX e ACCEPT Accept the adjustment setting REJECT Decline the adjustment setting and return to previous setting S HORIZONTAL SIZE When this item is selected there will be only the horizontal size icon with an adjustment indication bar under it between the main menu area and the video signal mode Press button to increase horizontal size Press to decrease Press OSD button to save the current setting and return to Geometry adjust submenu E PHASE When this item is selected there will be only the phase adjust icon with an adjustment indication bar under it between the main menu area and the video signal mode Press or button to adjust the pixel synchro
5. ctions in application of this merchandise The manufacturer is by no means responsible for any damage or hazard caused by improper application ABOUT THIS MANUAL This manual assists the user to utilize the LCD Monitor LM6100 series These series provide versatile font formats and support various instruction sets These series of products receive instructions in serial communication protocols and is capable of entering pass through mode so that all instructions received pass on to next connected serial device if properly configured The manufacturer of the LM6100 series heartily apologizes to the user for reserving the right to change or to modify this manual without notice due to the rapid and constant progress and improvement on science and technology The user may always obtain the most up to date information through any of our web sites http www posiflex com tw http www posiflexuk com http www posiflexusa com TRADE MARKS AND SERVICE MARKS All brand and product names and trademarks are the property of their respective holders Copyright Posiflex Technology Inc 2009 P N 19050900030 1 POSIFLEX ll MODEL NUMBERS LM6112 12 1 LCD Monitor w stand LM6101 12 1 LCD Monitor w joining mechanism for Posiflex touch terminals such as TP 8000 series LM6101 on back of TP8000 LM6112 lll CARTON CONTENTS LCD Monitor panel unit Monitor stand for LM6112 or joining mechanism for LM6101 Pivot scre
6. n bar under it between the main menu area and the video signal mode Press button to increase smoothness of display oo 99 decrease sharpness Press to go the other way Press OSD button to save the current setting and return to OSD submenu MODE SELECT Pressing OSD button on this icon will have no effect at all if the display mode is not one of the confusing modes The confusing modes here mean 640 x 400 or 720 x 400 in display resolution as both mode have refresh rate of 70Hz horizontal frequency of 37 9KHz and pixel frequency of 31 5MHz making it impossible for automatic select These modes are not used in normal Windows display g EXIT Return to Main menu EJ EXIT Exit OSD setup with all adjustment saved POSIFLEX VI SUPPORTED DISPLAY MODES For video signals beyond the supported display modes there will be a message Out Of Range on middle of screen Maximum supported color depth is 18 bits or 262 144 colors Supported display modes are as in the table Display Resolution Refresh Rate Hz Horizontal Frequency KHz 640 400 70 37 9 60 31 5 640 480 72 37 9 75 37 5 720 400 70 37 9 56 35 1 800 600 ss 31 2 72 48 1 75 46 9 60 48 4 1024 768 70 56 5 715 60 POSIFLEX G EHEAR REPRE Em EER Kapi FARE PREE E R HMF Bo RMA FR SRR EE a TNE
7. nization phase for best picture display Press OSD button to save the current setting and return to Geometry adjust submenu HORIZONTAL POSITION When this item is selected there will be only the horizontal position icon with an adjustment indication bar under it between the main menu area and the video signal mode Press or button to shift the screen display to right or left Press OSD button to save the current setting and return to Geometry adjust submenu Ss VERTICAL POSITION When this item is selected there will be only the vertical position icon with an adjustment indication bar under it between the main menu area and the video signal mode Press button to shift up the screen display Press to shift down Press OSD button to save the current setting and return to Geometry adjust submenu E EXIT Return to Main menu TOOLS SUBMENU When this item is selected there are 5 icons in this submenu eal Press OSD button to select item or return to main menu Press NXT button to select among OSD submenu reset to default phase smoothness sharpness adjust mode select and exit OSD SUBMENU When this item is selected there are 4 icons in this submenu eB Press OSD button to select item or return to main menu Press NXT button to select among OSD time OSD horizontal position OSD vertical position and exit OSD TIME
8. o make the choice POSIFLEX a ACCEPT Accept the reset result REJECT Decline the reset and return to previous setting e COLOR BALANCE ADIUS T When uns item is selected there will be 7 icons in this item Sia on fe between main menu area and the video signal mode Press OSD button to select an item or return to color adjust submenu Press NXT button to select among separate color adjust 4200K 5000K 6500K 7500K 9300K and exit SEPARATE COLOR ADJUST When this item is selected there will be 3 adjustment indication bars between the main menu area and the video signal mode Press NXT button to select among the 3 colors Red Green and Blue respectively Press button to intensify that color Press to reduce Press OSD button to save the current setting and return to Color balance adjust 3 submenu 4200K Pressing OSD button on this icon will set the color balance to a color temperature of 4200 degrees Kelvin pooo 5000K Pressing OSD button on this icon will set the color balance to a color temperature of 5000 degrees Kelvin 6500K Pressing OSD button on this icon will set the color balance to a color temperature of 6500 degrees Kelvin 7500K Pressing OSD button on this icon will set the color balance to a color temperature of 7500 degrees Kelvin 9300K Pressing OSD button on this icon will set the color bal
9. p part of this window is a Posiflex logo with the OSD firmware version indicated to its lower right Below this area is a row of icons for main OSD menu Below the main menu is a group of icons for submenu that corresponds to one icon selected in the main menu An analysis of the video signal on resolution and refresh rate will be displayed at the bottom Applicable icons in the main menu and its subsequent menus are explained below MAIN MENU There are in total 5 icons in this menu One of the 5 Vio VK S icons will be displayed in inverted color to indicate its POSIFLEX relationship with the submenu below Pressing NXT button will shift the selected icon one by one from left to right and then wrap around to the most left Press OSD button to enter the selected sub menu If there is no button for OSD setting is pressed within a period of time about 5 seconds to 1 minute as programmed the OSD window will disappear with all the adjusted parameters saved Explanations on items in sub menu are as below BRIGHTNESS CONTRAST ADJUST SUBMENU There are 3 b DEI Press OSD button to select item or return to main menu Press NXT button to select among brightness contrast and exit BRIGHTNESS ADJUST When this item is selected there will be only the brightness icon with an adjustment indication bar under it icons in this submenu p between the main menu area and the video signal mode Pres
10. s button ee 99 to increase brightness Press to decrease Press OSD N to save the current setting and return to Brightness Contrast submenu D CONTRAST ADJUST When this item is selected there will be only the contrast icon with an adjustment indication bar under it between the main menu area and the video signal mode Press button to ee 99 increase contrast Press to decrease Press OSD button to save the current setting and return to Brightness Contrast submenu g EXIT Return to Main menu COLOR ADJUST SUBMENU There are 4 icons in this submenu G BEEJ Press OSD button to select item or return to main menu Press NXT button to select among auto color adjust auto RGB reset Color balance adjust and exit AUTO COLOR ADJUST Upon an OSD button press on this icon the monitor will perform an automatic color adjustment and exits the OSD window leaving 2 icons below at center of the screen Press NXT button to switch the selection Press OSD button to make the choice ACCEPT Accept the adjustment setting e REJECT Decline the adjustment setting and return to previous setting AUTO RGB RESET Upon an OSD button press on this icon the monitor will perform an automatic RGB reset and exits the OSD window leaving 2 icons below at center of the screen Press NXT button to switch the selection Press OSD button t
11. w 1x and pan head fixing screws 2x for LM6101 User s Manual VGA cable Power adaptor amp power cord SON RT DoE Wall mount bracket with 4 screws IV INSTALLATION Base Mount and Stand along 1 Match the bottom of the panel unit into the monitor stand for LM6112 or p4 joining mechanism for LM6101 LM6112 Pivot Screw LM6101 ow 2 Screw on the pivot screw for LM6112 Screw on the pivot screw through a split washer and then through a plain washer for LM6101 POSIFLEX 3 Fix LM6101 to the Posiflex TP8000 terminal per instruction of the terminal 4 For LM6112 connect the end of VGA cable with the power connector to the back of the panel unit For LM6101 please arrange the power to be supplied through the interface cable from the main unit and just connect the video interface cable Connect the other end of VGA cable to the appropriate VGA port The monitor will always turn ON whenever power is made available Power Connector in VGA Cable r for LM6112 VGA Connector Power Connector from Power Adaptor 5 Adjust for best viewing tilt angle and engage the on screen display OSD adjustment for best display effect whenever necessary The monitor will sign for No Signal status and go into power saving mode in 5 seconds when there is no video signal The display will come back when the signal does Wall Mount 1 Please use the four screws which are attached with wall mount bracket to rotate into
Download Pdf Manuals
Related Search