English - Weintek.com
Contents
1. 11111 hat Tmefata sacart iatorra patinata The unit can be powered by DC power only voltage range 24 20 Volts DC compatible with It is necessary to connect the FIMI to CCC er ae EEN LN Power most controller DC systems The power conditioning circuitry inside the unit is accomplished by a NIA Gera a RJ 45 cable C IP address get from below switching power supply The peak starting current can be as high as 2A or l IP address 192 168 FF Subnet Mask 255 I 255 255 jg 0 If the display does not come on within 5 seconds of power up remove power An internal fuse will GateWay 192 168 25 Fusin AN A prevent damage if the polarity of the DC power is incorrect Check wiring for proper connections are and try to power up again An Internal fuse will prevent damage for overcurrent condition however it isn t guaranteed DC AN High Voltage voltage sources should provide proper isolation from main AC power and similar hazards eee A Hard wired EMERGENCY STOP should be fitted in any system using HMI to comply with ICS Q EasyBuilder Pro Software Settings Stop R Safety Recommendations Launch EasyBuilder Pro software select your A project file press F7 shortcut key to open Supply Do not power the unit and inductive DC loads or input circuitry to the controller with the same the downlode dialog box Voltage power supply Note The 24 VDC output from some controllers may not have enough current to Select Ethernet gt IP2. MT6000 8000iE series Installation Instruction installation and Startup Guide This document covers the installation of MT6000 8000iE Series HMI for the detailed specifications and operation please refer to Brochure and EasyBuilder Pro User Manual Install Environment NEMA Rating The MT6000 8000iE Series HMI is NEMA 4 rated Indoor Use Only The MT6000 8000iE Series has been tested to conform to European CE requirements This means that the circuitry is designed to resist the effects of electrical noise This does not guarantee noise immunity in severe cases Proper wire routing and grounding will insure proper operation Make sure that the displays are installed correctly and that the operating limits are followed Avoid installing units in environments where severe mechanical vibration or shocks are present Do not operate the unit in areas subject to explosion hazards due to flammable gases vapors or dusts Do not install the unit where acid gas such as SO2 exists This device should be mounted in the vertical position and for use on the flat surface enclosure Conform to UL508 ISBN 0 7629 0404 6 machine safety for use in Pollution Degree 2 Environment Electrical Environment Environmental Considerations NOTE Place the operator panel on a stable surface during installation Dropping it or letting it fall may cause damage unpacking the Unit Unpack and check the delivery If damage is found notify th
3. e and or physical injury to the operator Not used Data Rx If you use any programmable control systems that require an operator be aware that this potential safety hazard exists and take appropriate precautions Although the specific design steps depend on 3 RxD Received Data Data Rx j a your particular application the following precautions generally apply to installation of solid state 3 TxD Transmitted Data 3 Tx Tx programmable control devices and conform to the guidelines for installation of Controllers 4 Not used 4 Tx Tx recommended in NEMA ICS 3 304 Control Standards 5 GND Ground 5 GND GND COM1 TEROR 6 Not used 6 Not used To conform with ICS Safety Recommendations checks should be placed in the controller to ensure 7 RTS Ready to send output 7 Data Data Programming that all writable registers that control critical parts of plant or machinery have limit checks built into g CTS Clear to send input 8 _ Data AN Considerations the program with an out of limit safe shut down procedure to ensure safety of personnel GME608IE0_MT6070_8070_8100iE_Installation__150209 9 Not used 9 GND COM3 PiP sw settings AEAEE Touch Screen Calibration Mode Limited Warranty This product is limited warranted against defects in design and manufacture ON OFF ON OFF OFF Hide HMI System Setting Bar The proven defective product will either be repaired or replaced at Weintek s discretion OFF OFF ON OFF Boot Loader Mode This
4. e supplier 1 Installation Instruction 2 sided A4 1 2 Human Machine Interface 1 3 Power Connector 1 4 Brackets amp Screws 1 pack 5 USB Stick Clamp amp Tying Strap 1 6 Fuse 1 25A 250V 5 20mm 1 Installation Instructions Secure the operator panel in position using all the fastening holes and the provided brackets and screws ER A TE ee Am Be CEE USB Stick Clamp Usage Combining the USB Stick with the clamp and the tying strap can prevent USB stick from disconnecting with HMI when strong vibration is present 1 Insert the USB connector to the clamp and tie them together with the tying strap 2 Press the spring and insert the USB stick into HMI 4 Power Connections NOTE 1 Connect positive DC line to the terminal and the DC ground to the terminal 10 2 Please do not connect HMI with PLC and PC simultaneously to prevent potential difference from destroying USB ports of HMI and PC NOTE Make sure that all local and national electrical standards are met when installing the unit Contact your local authorities to determine which codes apply Osystem Settings Go to the Network tab you may choose CAUTION When HMI is powered up and displays image to auto get DHCP IP or designate your click the system setting button own IP EASE A etwork Time Date Securi is ory me settin Default System Password 1
5. tab gt Enter your HMI IP AN Condition POWE the unit gt Click Download to download this project file to HMI Wire Routin a Power wire length should be minimized Max 500m shielded 300m unshielded If use MT6070iE please select USB cable are ee ee i b Please use twisted pair cables for power wire and signal wire and conform to the impedance Please refer to EasyBuilder Pro User Manual piei A planing ene for software operation details PAPES c If wiring is to be exposed to lightning or surges use appropriate surge suppression devices ees d Keep AC high energy and rapidly switching DC power wiring separated from signal wires Communication Connections eee eee ot e Add a resistor and capacitor in the parallel connection between the ungrounded DC power NOTE 1 COM1 and COM3 RS485 2W support MPI 187 5K please use one at one time supply and the frame ground This provides a path for static and high frequency dissipation 2 COM1 RS485 COM3 RS485 with isolation protection N A for MT6070iE DANGER a a a COM1 RS232 9 Pin Male D sub ee RS485 9 Pin Female D sub 6789 9876 Hardware The system designer should be aware that devices in Controller systems could fail and thereby COM1 RS485 RS485 COM3 Considerations create an unsafe condition Furthermore electrical interference in an operator interface can lead to PIN Symbol COM1 R5232 PIN ore Tow La R5485 equipment start up which could result in property damag
6. warranty shall not cover any product which is E E E E OFF OFF ORE ON Not supported a Out of warranty period which is 12 months from the manufacturing month of the HMI products 1234 OFF OFF OFF OFF Normal b Damage caused by Force Majeure accident negligence improper installation or misuse NOTE Another method to enter touch screen calibration mode Press c Product has been repaired or taken apart by unauthorized technicians and hold anywhere on the screen for more than 2 seconds when HMI d Products whose identification markings have been removed or damaged starts
Download Pdf Manuals
Related Search