UNPACKING THE UNIT Your NVRS-F night vision riflescope comes
Contents
1. After mounting the riflescope it will be necessary to zero the scope by firing at a target and making the necessary adjustments using the reticle adjusting knobs 8 You may power up the scope and the IR iluminator via the remote control accessory by inserting the connector of the remote into the jack 9 ATTENTION Your NVRS F can be used in extremely cold temperatures However when the unit is brought back into a warm environment you must wait approximately 5 HOURS before using the unit This is due to condensation that may accumulate on the electronic circuitry EE ZEROING OF THE RIFLESCOPE It is recommended to zero your riflescope at operating temperature according to the following sequence place your rifle with a riflescope on a support make sure there are no bright light sources in your scope s field of view e put the target at a zeroing distance for instance 50m The illumination of the target area should not be greater than 1 lux remove flip up cap from the objective lens e activate the device by turning the power switch 3 to the ON position aim the foresight of the rifle to a center of the target adjust your scope according to the instructions listed in Operation section rotate the lever of the objective lens focusing ring 5 until the target image is clear adjust the reticle brightness by rotating the switch 4 if the centre of the target does not coincide with the aimin2. ALON Visual Magnification x Objective diameter mm Resolution lines mm Angular Field of View Recognition Range yd m Objective Lens Adjustment m Eyepiece Adjustment diopters Operating Voltage V Eye Relief mm Temperature Range Maximum Humidity Operating Time hour 0014 2 5 z gt 50 Maximum distance at which a human 35 figure can be recognized under ideal gt viewing conditions Ideal viewing 15 conditions are defined as clear 200 200 atmosphere no fog dust etc 1 2 with ambient light as produced by KE 1 4 moon 5x10 lux minimum a 45 22 F 104 F 30 C 40 C 93 50 Dimensions Length in mm Width in mm Height in mm Weight 0z kg 10 0 255 3 1 80 3 3 85 Mm UNPACKING THE UNIT Your NVRS F night vision riflescope comes with the following Carrying Case HEE OVERVIEW Photo Adapter Reducer Remote Control This User s Manual One Warranty Registration Card Your NVRS F starlight night vision scope is a professional quality device designed to provide high quality viewing in nearly total darkness Many active night vision devices require an artificial infrared light source The NVRS F is a passive starlight device it does NOT require any artificial light source The NVRS F does include a powerful infrared illuminator that is useful when the subject to be viewed is in shadows or total darkness The NVRS
3. F consists of a sophisticated electro optical assembly contained in an extremely durable titanium housing The entire unit is ruggedized for extreme field conditions It is entirely self contained and can operate for up to 50 hours at temperatures ranging from 22F to 104F 30C 40C Your NVRS F scope is ideal for a wide variety of professional and recreational uses including e Wildlife observation Security Search and rescue e Nighttime photo video EEE WARNINGS AND PRECAUTIONS Your NVRS F night vision scope was designed to provide many years of reliable service To ensure that you get the most enjoyment out of your NVRS F always obey the following Warnings and Precautions e Do not point the NVRS F towards any light source greater than 1 lux such as car headlights if the unit has been activated or if the eyepiece shows a green glow Turn the unit off and wait until the green glow dissipates before removing the lens cap e Do not open the case of the NVRS F or otherwise attempt to service this device Clean optical parts lenses with professional lens cleaning supplies designed for use with multicoated optics Failure to observe these warnings may void the warranty EE BATTERY INSTALLATION To install the two AA batteries unscrew the battery compartment cover Slide in the batteries according to polarity indicated on the cover Tighten the battery compartment cover 1 Clean the lens with professional lens cl
4. cameras For these purposes you require a night vision photo adapter for digital cameras Install the reducer into a riflescope s mount Setup the digital camera is done according to the photo adapter operating manual Mm STORAGE Always store the NVRS F in its case in a dry well ventilated area away from heating air conditioning vents or heating devices Temperature should not go below 50F Humidity should not exceed 70 Remove the batteries if the device is to be stored for longer than 2 months EE TROUBLESHOOTING The riflescope will not turn on Check that the battery is installed properly Install the battery according to the and polarity ensuring that the markings on the battery and battery compartment correspond with one another Check the battery contact to ensure it is clean and free of corrosion if necessary clean the contact Make sure that the external contact lug is not broken If necessary replace the battery as it may be depleted Also be sure that the power is in the ON position when trying to turn on the scope Distinct black dots appear on the screen The dots are minor cosmetic blemishes resulting from tube production processes and do not interfere with the reliability or performance of the riflescope e The image flickers flashes or snows The scope may flicker or flash when used in a bright environment to correct this place the cap over the objective lens and enter a dark environmen
5. eaning supplies intended for use with multicoated optics EE OPERATION Your NVRS F scope operates using two AA batteries Make sure they have been installed according to instructions listed in the Battery Installation section e Move into a dark area before powering on the device You can also try your scope in daylight with the lens cover on Remove the lens cap 2 only when the scope is in the dark e Activate the device by turning the power switch 3 down to the first click ON position e When additional illumination is needed activate the IR illuminator by turning the power switch 3 until second click IR position To iluminate the reticle turn the switch 4 clockwise and adjust the reticle brightness by rotating the switch clockwise or counterclockwise e To focus the scope select an object approximately 100 yds away Set the lever of the objective lens focusing ring 5 opposite the mark 100 m Direct your riflescope at the subject to be viewed and rotate the eyepiece focusing ring 6 until the image quality is optimal e The green LED indicates that the scope is on e After these adjustments irrespective of distance and other conditions do not rotate the eyepiece ring 6 adjust the image quality by rotating the lever of the objective lens focusing ring 5 The night vision riflescope NVRS F can be attached on any rifle equipped with a bar for side or top mounting by use of a Weaver mount 7
6. g dot the centre of the red reticle remove the caps from reticle adjusting knobs 8 and rotate the knobs R and UP until the centre of the target and the centre of the reticle coincide e aim at the aiming dot and fire 3 4 control shots determine the close grouping of shots and the position of the middle hit point e if the deviation of the middle hit point is more than the allowable value rotate the reticle adjusting knobs UP vertical adjustment R horizontal adjustment until the middle hit point coincides with the aiming dot One click of the adjusting knob will cause a 20mm shift at a distance of 100m check the accuracy of adjustment by shooting Your riflescope is zeroed at a chosen distance ATTENTION The recommended energy for Generation 1 Riflescopes NVRS F should not exceed 3700 Joules The Gen 1 riflescopes tolerate the overload shock corresponding to the caliber of no more than 7 62 300 The guarantee is null and void if cartridges with calibers of more than 7 62 300 or self made cartridges have been used EEE MAINTENANCE To avoid failures during operation of your riflescope and to provide the detection and elimination of reasons causing the premature deterioration of assemblies and parts in time it is necessary to carry out technical inspection and current technical maintenance of the riflescope A TECHNICAL INSPECTION It is necessary to take the following steps during technical inspection carry ou
7. he same caliber and type of bullets are being used as when the scope was initially sighted in If the scope was sighted in during the summer and is now being used in the winter or vice versa a small displacement of the aiming point is possible e Visibility decreases or disappears Bright light sources such as headlights may cause visibility to decrease or disappear and the image to flicker Turn the power off and turn the riflescope away from the light source visibility will restore itself in several minutes
8. t The scope will restore itself to a natural functioning state in several minutes or hours depending on how long the scope had been exposed to the light The scope may flicker for the first several seconds of use even when in a dark environment before the scope corrects itself and functions properly The scope may snow for several minutes after being exposed to a bright light source daylight a car s headlights fire etc even if being operated in complete darkness e The red reticle is blurred and can not be focused with the eyepiece The diopter adjustment range of the eyepiece is not powerful enough for your eye if you use glasses stronger than 5 diopters use your glasses while looking through the eyepiece The image will not focus but the red reticle is clearly seen Make sure the lenses are not foggy or dusty if so carefully clean the external surfaces of lenses with a soft cotton fabric Replace the battery if the total battery charge is less than 2 2 V When the unit is brought into a warm environment from a cold one condensation may appear on the internal lenses you must wait two hours before using the unit e The scope or the IR does not turn off via the ON OFF switch If the scope was activated by remote control then turn the scope and IR off by again using the remote control The reticle is being displaced while shooting Make sure that the scope is firmly attached to the mount and be sure that t
9. t the external examination of the riflescope external surfaces should not have splits dents and signs of corrosion check if the riflescope properly and securely mounted on the rifle clearance is inadmissible check the condition of optical surfaces objective and eyepiece lenses should not have splits fat stains dirt and various coatings on them check the condition of power supply elements and contacts contacts should not be oxidized or have salt coatings on e check the work of operation switches and of a reticle brightness switch Having detected some malfunction while using the riflescope it is necessary to check the following e riflescope s mounting on a rifle e the absence of dust dirt hoar frost water etc on the objective lens if the batteries are discharged e if the riflescope is on Pay particular attention to ensure that batteries have been installed B CURRENT TECHNICAL MAINTENANCE Carry out the current maintenance of the riflescope at least once in a half of a year Current maintenance requires the following steps to be taken remove dust dirt and moisture from the riflescope clean the external surfaces of metal parts clean the optics of the scope using a light coating of lens cleaning solution on a soft cotton cloth ATTENTION DISMANTLEMENT OF THE RIFLESCOPE IS PROHIBITED EE USING THE PHOTO ADAPTER You can take night pictures with the help of the riflescope using digital
Download Pdf Manuals
Related Search