RaySafe ThinX - ELSO Philips Service
Contents
1. ACTIVE COMPENSATION 15 10 mm Al total filtration for 45 100 kV Note If any parameter is out of range no measurement results will be shown PARAMETERS N 459 OO 1 84 mag 2T mmAl a A 68 5 klp D DEFINITIONS Exposure time is measured from start trig until the signal drops below 25 of max HF DC or from the first pulse that has a peak above 25 of max until the last time the signal drops below 25 of max AC All recorded samples are used to calculate dose and HVL Dose rate is dose exposure time kVp is calculated from 5 ms after trig until the signal drops below 75 of peak HF DC or from pulses with a peak signal level above 75 of maximum AC LED INDICATION Unfors ThinX Intra has three LED s Normal state is an idle blink every fourth second u Giese Idle blink The instrument is ready to use Intense blink An exposure has been recorded Yellow Replace the battery 100 exposures left Red Idle blink Replace the battery No further measurements are allowed Intense blink An error has occurred See details on display DISPLAY MESSAGES Exposure error message Low signal High signal Radiation during calculation Total filtration gt specification Time lt 10 ms Time gt 10 s Dose lt 20 uGy 2 3 mR Dose gt 999 mGy 114 R Dose rate lt 0 1 mGy s 0 7 R min Dose rate gt 100 mGy s 685 R min Number of pulses lt 3 for kVp kVp lt 45 kVp kVp gt 100 k2. CLEANING Use a damp cloth for cleaning INSTRUMENT VERSIONS This manual is valid for 1302023 A SUPPORT Do not hesitate to contact Unfors RaySafe for support Technical support 49 731175 492 20 technicalsupport raysafe com Service 46 31719 9710 customerservice se raysafe com 2012 08 Unfors RaySafe 5000099 B USER MANUAL RaySate ThinX Intra KA eed WRaySafe SPECIFICATIONS GENERAL EMC tested according to EN 61000 6 1 2007 and EN 61000 6 3 2007 Dimension Weight Display Power on Power off Battery Trig level DOSE Range 108x45x13 mm 4 3x1 8x0 5 in 70 g 2 5 02 128x64 pixels LCD auto radiation triggered 150 s after exposure 3V CR2450 0 1m Gy s 0 7 R min 20 uGy 999 mGy 2 3 MR 114 R at gt 70 kV Minimum dose at 50 kV Resolution Uncertainty DOSE RATE Range 100 uGy 11 4 mR 1 uGy 0 1 mR 9 0 1 mGy s 100 mGy s 0 7 R min 685 R min at gt 0 kV Minimum dose rate at 50 kV Resolution Uncertainty KVP Range Resolution Uncertainty HVL Range Resolution Uncertainty EXPOSURE TIME Range Resolution Uncertainty Bandwidth PULSES Number of pulses Uncertainty 0 5 mGy s 3 4 R min 0 01 mGy s 0 1 R min 5 45 100 kVp 0 5 kVp 3 1 0 10 0 mm Al 0 1 mmAl 10 or 0 2 mm Al 10 ms 10 s 1 ms 0 5 0 5 kHz 3 999 Max 375 ms dead time between pulses 1 pulse
3. D A X nei NO WRaySafe SPECIFICATIONS GENERAL EMC tested according to EN 61000 6 1 2007 and EN 61000 6 3 2007 Dimension 108x45x13 mm 4 3x1 8x0 5 in Weight 70 g 2 5 02 Display 128x64 pixels LCD Power on auto radiation triggered Power off 150 s after exposure Battery 3V CR2450 Trig level 0 1 mGy s 0 7 R min DOSE Range 20 uGy 999 mGy 2 3 mR 114 R at gt 70 kV Minimum dose at 50 kV 100 uGy 11 4 mR Resolution 1 uGy 0 1 mR Uncertainty 9 DOSE RATE Range 0 1 mGy s 100 mGy s 0 7 R min 685 R min at gt 70 kV Minimum cose rate at 50 kV 0 5 mGy s 3 4 R min Resolution 0 01 mGy s 0 1 R min Uncertainty 9 KVP Range Resolution Uncertainty HVL Range Resolution Uncertainty EXPOSURE TIME Range Resolution Uncertainty Bandwidth PULSES Number of pulses Uncertainty 45 150 kVp 0 5 kVp 3 1 0 10 0 mm Al 0 1 mmAl 10 or 0 2 mm Al 10 ms 10 s 1 ms 0 5 0 5 kHz 3 999 Max 375 ms dead time between pulses 1 pulse ACTIVE COMPENSATION 1 5mm AI 0 5 mm Cu total filtration for 45 125 kV 2 5 mm Al 10 mm Al total filtration for 125 150 kV 1 When measuring on an AMX4 or AMX4 multiply the displayed kVp value with 1 055 to get the correct kVp Note If any parameter is out of range no measurement results will be shown PARAMETERS 1 84 m aia 1 638 5
4. RaySate ThinX An easy tool for fast results Elso Philips Service KELSO Jilemnick ho 2 911 01 Tren n rie enia na presn meranie tel 421 32 6582410 fax 421 32 6582592 email elso elso sk R S TM web www elso sk OY q e AN EASY TO USE INSTRUMENT The RaySafe ThinX is an easy to use instrument thanks to its fully automatic user interface There is no need to adjust settings set up or range selection as the RaySafe ThinX works all automatically As soon as radiation is detected the instrument switches itself on by using the automatic on off function With a long battery lifetime of more than 1 year no maintenance is needed HOW IT WORKS measured values 1 POSITION INTRA POSITION RAD RaySate ThinX The RaySafe ThinX has been designed to meet the need for a basic multi parameter instrument for simultaneous measurement of dose dose rate kVp HVL time and pulses All parameters can be continually viewed in the convenient LCD display s AE ACTIVE COMPENSATION Thanks to the RaySafe Active Compensation technology no further corrections are required regarding variations in beam filtration to both kVp and dose measurements Multiple sensors and advanced calculations automatically determine the beam quality thereby eliminating the need for further corrections of measured kVp and dose values The solid state sensor technology enables maximum accuracy whilst making measurements as ef
5. Vp Number of pulses gt 999 Information message Battery low 100 exposures left Battery low Replace battery Instrument error Action Increase dose dose rate or kV Decrease dose dose rate or kV Wait longer between exposures or make the time be tween pulses shorter than 375 ms Decrease the amount of filtration Increase exposure time Decrease exposure time Increase dose Decrease dose Increase the dose rate Decrease the dose rate Increase the number of pulses to make an AC kVp calculation Increase kVp Decrease kVp Decrease the number of pulses Action Replace the battery Replace the battery immediately No further measurements allowed Please write down the error code and contact support contact information on back side of this manual
6. fortless as possible Simply position the meter under the X ray beam and make an exposure The display shows all 3 READ OUT U XPOSE 1 84 68 5 SPECIFICATIONS EMC TESTED According to BOSE RANE EN 61000 6 1 2007 and RANGE 0 1 mGy s 100 mGy s at gt 70 kV EN 61000 6 3 2007 0 7 R min 685 R min EXPOSURE NEEDED One Minimum dose rate at 50 kV POWER ON Auto radiation triggered IS 9 3 Moys AAA Rmin POWER OFF Automatic after 2 5 min of inactivity RESOLUTION 0 01 mGy s 0 1 R min RESET Automatic UNCERTAINTY 5 BATTERY 3V CR 2450 HVL BATTERY LIFE 2 years of typical use RANGE 102100 mm AI READ OUT 128 x 64 pixel LCD RESOLUTION 0 1 mm AI TRIG LEVEL 0 1 Gy s 0 7 R min SIZE H x W x L 13 x 45 x 108 mm UNCERTAINTY 10 or 0 2 mm Al 0 5 x 1 8 x 4 3 in EXPOSURE TIME WEIGHT lt 70 g 2 5 02 RANGE 10 ms 10 s Ip UNCERTAINTY 0 5 RANGE RAD 45 150 kVp RESOLUTION 1 ms RANGE INTRA 45 100 kVp BANDWIDTH 0 5 kHz RESOLUTION 0 5 kVp _ UNCERTAINTY 3 jaro mm PULSES 3 999 pulses max 375 ms dead time da between pulses RANGE 20 uGy 999 mGy at gt 70 kV 2 3 mR 114 R UNCERTAINTY 1 pulse Minimum dose at50 kV ACTIVE COMPENSA is 100 uGy 11 4 mR RANGE RAD 1 5 mm AI 0 5 mm Cu total filtration RESOLUTION 1 Gy 0 1 mR 45 125 kVp UNCERTAINTY 5 2 5 10 mm Al total filtration 125 150 kVp RANGE INTRA 1 5 10 mm Al total filtration 45 100 kVp MODEI PARAMETERS 0 If the X ray generator wavefo
7. klip at m PA Instrument model Dose kVp Dose rate HVL Time Pulses RAD RAD kVp 3 RAD Dose gt DEFINITIONS Exposure time is measured from start trig until the signal drops below 25 of max HF DC or from the first pulse that has a peak above 25 of max until the last time the signal drops below 25 of max AC All recorded samples are used to calculate dose and HVL Dose rate is dose exposure time kVp is calculated from 5 ms after trig until the signal drops below 75 of peak HF DC or from pulses with a peak signal level above 75 of maximum AC LED INDICATION Unfors ThinX RAD has three LED s Normal state is an idle blink every fourth second Idle blink The instrument is ready to use eee Intense blink An exposure has been recorded Yellow Replace the battery 100 exposures left Red Idle blink Replace the battery No further measurements are allowed Intense blink An error has occurred See details on display DISPLAY MESSAGES Exposure error message Low signal High signal Radiation during calculation Total filtration gt specification Time lt 10 ms Time gt 10 s Dose lt 20 uGy 2 3 mR Dose gt 999 mGy 114 R Dose rate lt 0 1 mGy s 0 7 R min Dose rate gt 100 mGy s 685 R min Number of pulses lt 3 for kVp kVp lt 45 kVp kVp gt 150 kVp Number of pulses gt 999 Information message Battery l
8. ow 100 exposures left Battery low Replace battery Instrument error Action Increase dose dose rate or kV Decrease dose dose rate or kV Wait longer between exposures or make the time between pulses shorter than 375 ms Decrease the amount of filtration Increase exposure time Decrease exposure time Increase dose Decrease dose Increase the dose rate Decrease the dose rate Increase the number of pulses to make an AC kVp calculation Increase kVp Decrease kVp Decrease the number of pulses Action Replace the battery Replace the battery immediately No further measurements allowed Please write down the error code and contact support contact information on back side of this manual RaySafe ThinX measures X ray radiation The instrument is always on triggered by radiation You don t need any correction tables since the active compensation feature automatically applies correc tions for variation in beam filtration Position RaySafe ThinX on a flat surface Posi tion the collimator of the X ray machine close to the sensor area Expose Read the values on the display If the detected waveform is pulsed the num ber of pulses will automatically be displayed BATTERY REPLACEMENT When the yellow LED is blinking please replace the battery 1 Remove the battery cover 1 eng 2 Replace the battery CR2450 Ga 3 Putthe cover back The instru ment is ready to use
9. rm is pulsed the instrument will also RaySafe ThinX Intra Dose rate kVp HVL time pulses automatically display pulses RaySafe ThinX RAD Dose rate kVp HVL time pulses RaySafe ThinX RAD kVp kVp time pulses RaySafe ThinX RAD Dose Dose rate HVL time pulses Unfors Instruments has changed its name to Unfors RaySafe www raysafe com WRaySafe 2013 06 Unfors RaySafe 5200044 B RaySafe ThinX measures X ray radiation The instrument is always on triggered by radiation You don t need any correction tables since the active compensation feature automatically applies correc tions for variation in beam filtration Position RaySafe ThinX with the sensor area centered in the X ray field Expose Read the values on the display If the detected waveform is pulsed the num ber of pulses will automatically be displayed BATTERY REPLACEMENT When the yellow LED is blinking please replace the battery 1 Remove the battery cover 2 Replace the battery CR2450 3 Putthe cover back The instru ment is ready to use CLEANING Use a damp cloth for cleaning INSTRUMENT VERSIONS This manual is valid for 1302024 A 1302025 A and 1302026 A SUPPORT Do not hesitate to contact Unfors RaySafe for support Technical support 49 731175 492 20 technicalsupport raysafe com Service 46 31719 9710 customerservice se raysafe com 2012 08 Unfors RaySafe 5000094 B USER MANUAL RaySate ThinX RA
Download Pdf Manuals
Related Search