Advanced Lock英文说明书.cdr
Contents
1. Armature plate Cables shall be larger than 0 75mm2 in case of power supply with a large power capacity the output of power supply controlled within 12VDC 15 strictly The screw connecting locks and Armature plate shall be tightened Check the fixing of the lock and the board after three months Install carefully to avoid damage to Armature plate and the galvanized coating of locks and otherwise the normal use suction force and service life will be damaged The complete contact between the Armature plate and the lock as well as the size of contact surface will decide the suction force directly A rubber ring is required between the Armature plate and the lock so as to maintain a proper flexibility of the suck board and tensive screws of the Armature plate shall not be fixed too tightly in order to maintain the appropriate flexibility of rubber ring Armature plate cannot be welded on the door directly and otherwise the normal use of magnetic locks will be damaged Wipe off rust preventive oils on the locks with cotton cloth while alkaline or irritant detergents not allowed Precautions NO GR wNa SK Door Frame AD Door Frame Thickness Al Thickness A2 f TT eT TTT Series mm mm M I LE EET a te a a A er ey eP Leese eS AP 280 543 553 Door frame not less than 5mm AP 350 gt 42. Magnetic Lock Series Electric Bolt Lock series Electric Strike Series Mechanical Lock Seriess Electronic Lock Series Brackets and Accessories ISO9001 ISO9001 AL 130 Series Electric Strike User Manual wm E Welcome to use Advanced Lock products In order to protect your rights and interests read this User Manual carefully before use Please contact the dealer or the manufacturer in case of query Applicable Range This lock is applicable for use together with anode mechanical lock or ball lock in office buildings wooden doors stainless steel doors fire doors and entrance gate of residence community Product Advantage Recessed type installation and pleasant looking appearance The electromagnetic part adopts high quality magnetic materials and special processing workmanship to ensure normal use and no residual magnetism even after long time operation Door Opening 90 and available for load of 250kg Electrical Gar Users can select appropriate products with different models and functions based on the following table Customization is available according to users requirements Voltage DC Current mA Unlock Method NO unlock by AL 130NO 12V 15 et ma oe omnia power Customization is available for products with 6 24VDC i NC unlock by AL 1 30NC 12V 15 disconnecting power Wiring 1 One diode is an accessory provided in the accessory bag The diode is used to prevent bounce back current and voltage produc
3. EWC118303Q EWC118303Q 2000 BD 0982 s APPROVED 9 Welcome to use Advanced Lock prod ucts In order to protect your rights and inter ests read this User Manual caref ully before use Please contact the dealer or the manufact urer in case of query Applicable Range This lock is applicable for use together with anode mechanical lock or ball lock in office buildings wooden doors stainless steel doors fire doors and entrance gate of residence community Product Advantage Recessed type installation pleasant looking appearance wide lock mouth and more extensive application The electromagnetic part adopts high quality magnetic materials and special processi ng workm anshi p to ensure normal use and no residual magnetism even after long time operation Door Opening 90 and available for load of 400kg Electrical Property Users can select appropri ate products with different models and functions based on the following table Customization is available acco a to users requirements Voltage DC Current mA Unlock Method NO unlock by Re AL 131NO 12V419 gt oe Customization is available for Ss Onneg ROWE products with 6 24VDC NC unlock b AL 1 31NC 12V 15 disco ecg pout Wiring 1 One diode is an accessory provided in the accessory bag The diode is used to prevent bounce back current and voltage produced during locking or unlocking from affecting the access control mainframe Users can connect the diode to the wiring termi
4. Step 9 After installation is finished typical and the center line of bolt hole on the magnetic wooden door installation effect is shown in the buckling plate diagram above Step 7 Fix the magnetic buckling plate on the door with screws 2 Installation diagram Dimensions of Electric Bolt Lock Z oy P mE ae Cover metal plate WET A Moles EST Electric Bolt Lock series Electric Strike Series Mechanical Lock Seriess Electronic Lock Series Brackets and Accessories WET AA oTe EST Electric Bolt Lock series Electric Strike Series Mechanical Lock Seriess Electronic Lock Series Brackets and Accessories ELECTRIC LOCKS CERTIFIED CERTIFIED ae os Magnetic Lock User Manual EDH OT CE D OEA ABA F044 EWC118303Q EWC118303Q congas APPROVED R4 RE Welcome to use Advanced Lock prod ucts In order to protect your rights and inter ests read this User Manual caref ully before use Please contact the dealer or the manufact urer in case of query Applicable Range This lock is applicable for use together with building interphone and access control system This lock is applied extensively in security door emergency door and fire door Product Advantage The magnetic lock adopts professional magnetic materials and special processing workmanship No residual magnetism is produced even after long time operation Long time use will not cause magnetization of adsorption plate and result in reduction of adsorptive force This lock has longer
5. Tn Jewo Nol Noo j ek a i Se A scm em eg et iy Gece ste el Precautions 1 Read this User Manual carefully before installing the electric strike 2 Select qualified power source and wires to avoid insufficient locking force caused by abnormal power supply 3 This lock has no delay function If delay function is necessary it shall be used together with the controller AL 132 Series Electric Strike Installation Drawing 25mm Electric strikes 240mm 220mm Mechanical LAL Tf Lock Electric strikes 3 Door Frame gg ee SS Latch Installation Precautions 1 Allow a 1 2mm gap between the electric strike and the bolt of electric dropbolt Otherwise normal g door opening will be affected Fig 1 Fig 1 2 Allow a 3 5mm gap between the electric strike and the face plate of electric dropbolt Otherwise smooth door closing will be affected Fig 1 Magnetic Lock Series Electric Bolt Lock series Electric Strike Series Mechanical Lock Seriess Electronic Lock Series Brackets and Accessories ET Fala d em oTe ESTA Electric Bolt Lock series Electric Strike Series Mechanical Lock Seriess Electronic Lock Series Brackets and Accessories AL 133 Series Glass Door Lock User Manul A A o om CE P EWC118303Q EWC118303Q SV taovoy cH 10002 s APPROVED KF RE Welcome to use Advanced Lock prod ucts In order to protect your rights and inter ests read this User Manual caref ully before use Please contact
6. Access control 7 i anne a Access controller oT wel on Gah A Sit aa I il a i ccess Permanent magnet qa waussetplate ee a Ff i controller l Mic AL 300 eno nef nofoo 7 Time delay diagram Ea diagram1 Diagram only for reference Standard packing list Cover metal Plate L210XW40XH1 ee Se e aT wanna 7 istataton E Component Number Series AL 100 AL 300 Applicable Range Remark s r l The distance between glass door Upper Bracket AL 200PZ AL 200PZ glass door E and door frame can not less than 7mm Bracket on frameless door The distance For down frameless between glass door and door frame Down Bracket AL 100PF AL 100PF can not less than 4mm on unilateral frameless door Side mount bracket for hollow frame ro er elow aper 2 Precautions 1 Installation shall be conducted as per the User Manual and the installation drawing Cut off the power during installation and wiring Do not carry out wiring with power connected 2 Select qualified power source and wires to avoid out of service of the lock due to abnormal power supply It is recommended to connect the lock to the power source 3 Make sure the installation position is proper and firm Otherwise the bolt will lock improperly and the lock will produce heat leading to shortening of lock service life 4 If the lock fails to work after the power is connected check whether the permanent magnet is aligned to the m
7. fix the L auxiliary bracket to the doorframe Step 2 Use cross screwdriver to dismount the anti dismantle screw on the lock The sign refer t rotate direction 2 Inside Outside a E E a en a ae ie NN a a a a a a a Gn E E T im i Step 4 Use Allen key to install the lock to L bracket Be careful to hold the screw to prevent slipping Step 5 Use cross screwdriver to mount the anti dismantle screw onto the lock ae ree a D ran ees a mm a S O en a Pangan E cee ee R a R etme e a E a ate em may ee ee Sere es firme a Perey Strats L O Sie eta Remy E a a a S geen rent ram comers ree me Pee ie tae eee ees Rhee ee ete eee ie L ees eee a Coy eee a ee es ee Inside a Ng a a a A Ce ee ae ge ee 2 Step 9 Fix Z bracket to relevant position on the door leaf Note Keep tight contact between the sub plate and the lock BS a ee ise co T cps ices Sed EE eee ee ee en mh eet Aes E me med a RN eet Samet Ge Tey eee che Step 7 Use cross screwdriver to assemble the Z bracket Step 8 Install the sub plate to the Z bracket see schematic diagram in Fig 8 a A a a a a a a a aA a a aA a a a a a a a a a a a a h a a A ae el a a g i i Position L bracket a ices ao Length Width Height rubber ring v AL 180PL 166 26 50 2 TAL 180DPL 332 26 50 it RS dl ee AL 180PZ 131 40 100 o AL 280PL 253 30 50 Ho
8. 2 The screw fixing the adsorption plate shall not be tightened excessively Allow proper resilience for the rubber ring to make it available for adjusting the adsorption plate to the correct position so as to produce maximal adsorption force See Fig 2 Dimension Identification Series Model gg A F AP 180D0_ 332 35 23 130 8 D Sucking Disk AP 280D LED 506 42 245 6 248 185 38 12 AP 350D LED 506 48 275 6 273 185 48 12 CAP 5OOD LED 560 70 385 7 37 5 1845 58 14 5 a E a ee H L Sucking Disk 4 253 APSOUEED 253 48 275 6 27 i 185 46 12 4 184 5 A2 B2 C2 D2 E2 F 3 ott AteoM 166 35 21 198 20 182 130 3 Magnetic Lock Series Electric Strike Series Electronic Lock Series Brackets and Accessories WET Fala dem Moles EST Electric Bolt Lock series Electric Strike Series Mechanical Lock Seriess Electronic Lock Series Brackets and Accessories Diagram of Magnetic Lock Auxiliary Bracket Installation Procedures Inward opening Door AL 180PL AL 180DPL AL 280PL AL 280DPL AL 350PL AL 350DPL AL 500PL AL 500DPL AL 180PZ AL 280PZ AL 350PZ AL 500PZ k The sign refer to rotate oo Ss re a ee ee ee ee BS es as a a ees aes ea ee es a es as as i M as Ss es a a A Step 3 Use Allen key to separate the connecting plate from the bottom of the lock Be careful to hold the screw to prevent slipping Step 1 Use cross screwdriver to
9. 6 gt 56 il Pull out AP 500 gt 58 gt 68 Pull out 10 During installation of this product offset toward right left upside and downside of center position of both the adsorption plate and the lock shall not exceed 3mm Direction X mm Y mm Left lt 3 O X T Right lt 3 O Up O lt 3 Down 0 S3 WET Fala dem Moles ESTA Electric Bolt Lock series Electric Strike Series Mechanical Lock Seriess Electronic Lock Series Brackets and Accessories ET Fal a dem oTel EST Electric Bolt Lock series Electric Strike Series Mechanical Lock Seriess Electronic Lock Series Brackets and Accessories Magnetic Lock Installation Drawing Armature Doorframe Armature Armature plate plate Magnetic Lock Magnetic Lock Pull out Push in double door pull out type Door frame Circuit diagram for L type cable only COM NC NO The products normally use 12VDC See Diagram2 If use 24VDC please take the JP 2 and 3 connected See Diagram1 T Sucking disk Diagram 3 24VDC Diagram 1 12VDC Wiring Description see Fig 1 Precautions for installation of adsorption plate 1 The rubber ring in the accessory bag must be installed between the adsorption plate and the door to ensure impulse force and balance the contact between each other
10. Gusset Glass door Position Model eee E CORe 106 61 48 Upper bracket Length Width Height Glass door Down bracket WET Fala dem Moles ESTA Electric Bolt Lock series Electric Strike Series Mechanical Lock Seriess Electronic Lock Series Brackets and Accessories
11. L bracket TAL 280DPL 506 30 50 Pt AL 280PZ 185 50 100 eae E i AL 350PL 253 30 50 o 7 bracket AL 350DPL 506 30 50 Ho AL 350PZ 185 50 100 Me j SOE E AL 500PL 280 42 72 Step 10 inetallatiow is nished Note The rubber ring must be installed to keep AL S500DPL 560 42 72 proper resilience see Fig 10 AL 500PZ 185 65 133 Magnetic Lock Series Electric Bolt Lock series Electric Strike Series Mechanical Lock Seriess Electronic Lock Series Brackets and Accessories ET Fala dem oTe EST Electric Bolt Lock series Electric Strike Series Mechanical Lock Seriess Electronic Lock Series Brackets and Accessories Diagram of Magnet ic Lock Auxiliary Bracket Installation Procedures Downside Frameless Glass Door AL 180PU AL 280PU AL 350PU AL S00PU Schematic Connecting plate diagram __ j I I l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l Doorframe 4 Step 1 Use cross screwdriver to dismount the Step 2 Use Allen key to separate the connecting Step 3 Use screws to fix the connecting plate anti dismantle screw on the lock plate from the bottom of the lock to the doorframe and fix relevant positions WN S amp i S VRS VNR 7 a Door frame Install the tamper screw Step 4 Use Allen key to install the lock onto the Step 5 Use cross scre
12. agnetic induction area and check connection correctness of the electric circuit amp power source If the multimeter is used to measure the load make sure that voltage at lock power input end shall not be less than 12VDC Magnetic Lock Series Electric Bolt Lock series Electric Strike Series Mechanical Lock Seriess Electronic Lock Series Brackets and Accessories ET AA oTe EST Electric Bolt Lock series Electric Strike Series Mechanical Lock Seriess Electronic Lock Series Brackets and Accessories Diagram for Electric Bolt Lock Installation Procedures 1 Installation Procedures Note Call us for installation method for hollow door and metal door Step 1 Firstly make sure the door is closed Step 2 Align the center line of perforated Step 3 Use drilling tool to drill holes at positions properly Then decide the center line and sticking paper to the center line on the doorframe corresponding to type of electric bolt lock mark on the doorframe and door leaf Then stick the paper on it Step 5 Decide the center line according to the Step 6 Use special drilling tool to drill holes on door electric bolt lock and the bolt Then stick relevant type of magnetic buckling plate the perforated paper to the door according to corresponding electric bolt lock 8 Step 4 Fix the lock and the decoration plate on the doorframe based on the holes N 1 S j ESAE Schematic diagram Step 8 Keep alignment between bolt center line
13. distance between glass door and doorframe shall not be less than 7mm In case only one part is frameless glass the distance between glass door and doorframe shall not be less than 4mm i Clamp the lock and the U bracket upwards to the corresponding position After assembling the effect is as shown en use the screwdriver to fix it Lock Upper bracket q Class frame Position Length Width Height Down bracket e al Glass door jy lt AL 200PZ 205 61 48 Diagram of Electric Bolt Lock Downward Bracket Installation Procedures AL 100PF Decoration plate Fix it with screws he screws Then dismantle U bracket Adjust the position eosere els ROWne gt and then fix it on the glass door with screws Use screwdriver to dismantle Install spacer for downward 3 Assemble the dismantled a accessory cover and then assemble it together with the U bracket Close o Glass door Close over Fix the magnetic buckling _ After assembling the effect is as Note In case both the upside and downside parts are Screws doorframe shall not be less than 7mm ln case only one part is frameless glass the distance between glass door and doorframe shall not be less than 4mm _ G plate on the bracket with Ke shown in Fig 6 frameless glass the distance between glass door and
14. ed during locking or unlocking from affecting the access control mainframe Users can connect the diode to the wiring terminal in parallel A e ee a Access controller Jel noloo Precautions 1 Read this User Manual carefully before installing the electric strike 2 Select qualified power source and wires to avoid insufficient locking force caused by abnormal power supply 3 This lock has no delay function If delay function is necessary it shall be used together with the controller AL 130 Series Electric Strike Installation Drawing 35 LOs ae ie yy gt _ _ p LLY LL Electric strikes NN SN NN Mechanical Lock P E A ENE E EN Y A EA IAE E NETT E R E ESE AA Electric strike Door Frame Latch Installation Precautions 1 Allow a 1 2mm gap between the electric strike and the bolt of electric dropbolt Otherwise normal door opening will be affected See Fig 1 2 Allow a 3 5mm gap between the electric strike and the face plate of electric dropbolt Otherwise smooth door closing will be affected See Fig 1 Magnetic Lock Series Electric Bolt Lock series Electric Strike Series Mechanical Lock Seriess Electronic Lock Series Brackets and Accessories ce Fig 1 ET AA Moker ESTA Electric Bolt Lock series Electric Strike Series Mechanical Lock Seriess Electronic Lock Series Brackets and Accessories AL 131 Series Electric Strike User Manual T E C E
15. ime operation This lock was designed and manufactured based on electronic mechanical and mechanics principle to realize low current operation and reduce rate of failure and maintenance Auxiliary bracket can be used for installation of frameless glass door Door Opening 180 and available for load of 1000kg Electrical Property and others Users can select suitable products with different models and functions based on the following table Customization is available according to users requirements aa a Door Lock With Ball Indicator Volt DC UnLock mode Delay function AL 300 Unlock by Adjustable at 0 3 6 9 200X35X38 12V 15 j Yes Yes seconds Pore PENAN m a See Diagram 1 Wiring 1 Power source Red wire is the positive input end of the lock power source and shall be connected to positive end Black wire is the negative input end of the lock power source and shall be connected to negative end of the power source 12VDC 2 Door signal conventional 2 wires configuration upon delivery Two white wires are used for door status signal NO normal open indicates door opening status output end Limited current of door status signal is 300mA when the input voltage is 12VDC Overload is forbidden Door opening and closing status can be monitored after it is connected to the central control room 3 The indicator lamp indicates working status of the electric lock and turns red after connected to power Door signal nonconven
16. nal in parallel O R A A i iA F 044 x d m a ee oe e E comm n Ce Leon Oa a a TEE y m e a o I U a e m _ 4 ms weno ee ee manno me eee ee ee ee ee ee marmo manene t Precautions 1 Read this User Manual carefully before installing the electric strike 2 Select qualified power source and wires to avoid insufficient locking force caused by abnormal power supply 3 This lock has no delay function If delay function is necessary it shall be used together with the controller AL 131 Series Electric Strike Installation Drawin Electric strikes is N Mechanical Lock Installation Precautions 1 Allow a 1 2mm gap between the electric strike and the bolt of electric dropbolt Otherwise normal door 7 opening will be affected Fig 1 2 Allow a 3 5mm gap between the electric strike and the face plate of electric dropbolt Otherwise smooth Fig 1 door closing will be affected Fig 1 WET Fala L Moker EST Electric Bolt Lock series Electric Strike Series Mechanical Lock Seriess Electronic Lock Series Brackets and Accessories ET AA oTe EST Electric Bolt Lock series Electric Strike Series Mechanical Lock Seriess Electronic Lock Series Brackets and Accessories ISO9001 ISO9001 AL 132 Series Electric Strike User Manual lt gt O mm CC P CTR J I JA F 044 EWC118303Q EWC118303Q mwanz 3 Welcome to use Advanced Lock prod ucts In order
17. service life and is free of mechanical failure abrasion and noise Auxiliary bracket can be used for installation of frameless glass door Door Opening 90 Electrical Property Users can select suitable products with different models and functions based on the following table Customization is available according to users requirements Di Voltage Curr ent Indicator Lamp amp Signal imensions mm DC mA Output NC NO AL 180M 198X21X35 Not provided AL 180 166X21X40 12V 10 Not provided AL 180D 332X21X40 Not provided AL 280 LED 253X25X48 500 250 12V 10 AL 350 LED 953X28X55 500 250 24V 10 AL 350D LED 506X28X55 1000 500 AL 500D LED 560X38 5X70 1400 700 Wiring The positive phase and negative phase are connected to the power box Use the model that has signal output Signals are connected as required by users 1 Connected to COM and NO if normal open signals are necessary 2 Connected to COM and NC if normal close signals are necessary 3 The indicator lamp turns red if the lock is separated from the adsorption plate or if contact is not thorough The lamp will turn green if the lock and the adsorption plate contact with each other correctly 4 in case of abnormal indicator lamp when the lock is working it may be caused by improper contact between the lock and the adsorption plate Adjust the position of the lock and the adsorption plate to ensure thorough contact AL 350 LED Access control TnT controller
18. t power 3 This lock has no delay function If delay function is necessary it shall be used together with the controller AL 133 Series Glass Door Lock Installation Drawing Door Frame Lock Body Lock Body Front Tablet Front Tablet Back Tablet Back Tablet non non n tr Glass Door Glass Door n P Hou ou M5X10 Screw Ry G Door closing illustration Door opening illu stration Note The door must press the rear pressing sheet when closed overnise normal opening will be affected Magnetic Lock Series Electric Bolt Lock series Electric Strike Series Mechanical Lock Seriess Electronic Lock Series Brackets and Accessories WET AA oTe EST Electric Bolt Lock series Electric Strike Series Mechanical Lock Seriess Electronic Lock Series Brackets and Accessories Electric Bolt Lock User Manual a Fa a D O mA CE ORA BA F044 2 EWC118303Q Wet 2000 mA H0902 s APPROVED 9 Welcome to use Advanced Lock prod ucts In order to protect your rights and inter ests read this User Manual caref ully before use Please contact the dealer or the manufact urer in case of query Applicable Range This lock is applicable for office buildings and frame door at the entrance of residence community Product Advantage Recessed type installation and pleasant looking appearance The electromagnetic part adopts high quality magnetic materials and special processing workmanship to ensure no residual magnetism even after long t
19. the dealer or the manufact urer in case of query Applicable Range This lock is applicable for use together with anode mechanical lock or ball lock in office buildings wooden doors stainless steel doors fire doors and entrance gate of residence community Product Advantage Recessed type installation pleasant looking appearance wide lock mouth and more extensive application The electromagnetic part adopts high quality magnetic materials and special processi ng workm anshi p to ensure normal use and no residual magnetism even after long time operation Door Opening 90 and available for load of 250kg Electrical Property Users can select appropri ate products with different models and functions based on the following table Customization is available acco rding to users requirements NC unlock b 12V415 peee power Wiring 1 One diode is an accessory provided in the accessory bag The diode is used to prevent bounce back current and voltage produced during locking or unlocking from affecting the access controller Users can connect the diode in parallel to the wiring terminal at the electric lock power input end AL 133NC Access control power source i 1 Access controller l y aes amp Precautions 1 Read this User Manual carefully before installing the electric strike 2 Select qualified power source and wires to avoid insufficient locking force caused by abnormal power supply insufficien
20. tional 3 wires configuration customized When the door is under the opening status the green wire blue wire and orange wire refer to COM common wire NC normal close and NO normal open respectively Limited current of door status signal is 300mA when the input voltage is 12VDC Overload is forbidden Door opening and closing status can be monitored after it is connected to the central control room Lock signal conventional 2 wires configuration upon delivery When the door is under the opening status the purple wire and light blue wire output NO normal open lock signals The purple wire and orange wire output NC normal close lock signals In case of 2 wire signal output select only one between NO and NC limited current of lock status signal is 300mA when the input voltage is 12VDC Overload is forbidden Locking and unlocking status can be monitored after it is connected to the central control room 3 Lock signal nonconventional 3 wires configuration customized When the door is under the opening status the purple wire orange wire and light blue wire refer to COM common wire NC normal close and NO normal open respectively The purple wire and orange wire output NC normal close lock signals Limited current of lock status signal is 300mA when the input voltage is 12VDC Overload is forbidden Locking and unlocking status can be monitored after it is connected to the central control room Remark O can be customized
21. to protect your rights and inter ests read this User Manual caref ully before use Please contact the dealer or the manufact urer in case of query Applicable Range This lock is applicable for use together with anode mechanical lock or ball lock in office buildings wooden doors stainless steel doors fire doors and entrance gate of residence community Product Advantage Recessed type installation pleasant looking appearance wide lock mouth and more extensive application The electromagnetic part adopts high quality magnetic materials and special processi ng workm anshi p to ensure normal use and no residual magnetism even after long time operation Door Opening 90 and available for load of 400kg Electrical Property Users can select appropri ate products with different models and functions based on the following table Customization is available acco rding to users requirements Model Voltage DC Current mA Unlock Method NO unlock AL 132NO 12V 15 acdc ie Customization is available for products with 6 24VDC AL 132NC 12V 15 Mo unioni Dy disconnecting power Wiring 1 One diode is an accessory provided in the accessory bag The diode is used to prevent bounce back current and voltage produced during locking or unlocking from affecting the access control mainframe Users can connect the diode to the wiring terminal in parallel AL 132NC ee 3 r ee eM ee Be ee ee ee ee ee eS d f Access controller
22. wdriver to install wire box Step 6 Install U bracket to the glass door and doorframe connecting plate in corresponding cover and the anti dismantle screws align it with lock position on the doorframe Then position fix it with screws Small metal oe for height SST osition iene eae Feien oi Model AL 180PU 140 29 40 E AL 280PU_ 195 29 40 Screw Outside Inside AL 350PU 195 6 rv i l Glass door AL 500PU 198 42 66 Step 7 Use screws to fix the su b plate and 7 Step 8 miona aae the U bracket Their positions shall be consistent Make sure the rubber ring is installed during installation WET LAA ole ESTAA Electric Bolt Lock series Electric Strike Series Mechanical Lock Seriess Electronic Lock Series Brackets and Accessories ET AA oTe EST Electric Bolt Lock series Electric Strike Series Mechanical Lock Seriess Electronic Lock Series Brackets and Accessories Diagram of Electric Bolt Lock Upward Bracket Installation Procedures AL 200PZ The U bracket clamps upwards Use screws to fix the cover and the the glass frame according to L bracket to the main frame thickness use spacer of the glass door After correction of the position fix it on the glass Use screwdriver to dismantle the screws under the upward bracket 4 Glass frame Note In case both the upside and downside parts are frameless glass the
Download Pdf Manuals
Related Search