MCF5253 Evaluation Board Quick Start Guide
Contents
1. A USB to serial adapter if your computer is not equipped with a serial port A USB flash drive also known as a jump drive or a thumb drive A computer meeting the following requirements Windows 98SE or later An available DB 9 serial port or an extra USB port for a USB to serial adapter An available USB port MCF5253 Evaluation Board Quick Start Guide Rev 0 Freescale Semiconductor EE Preparing the EVB for Operation 2 Preparing the EVB for Operation This section provides instructions for setting jumpers on the EVB circuit board and connecting it to your computer 2 1 Configuring the EVB Jumpers The EVB circuit board is shipped from the factory with several jumpers A complete listing of the jumpers is found in the M5253EVB User s Manual To run the USB demonstration e Leave the factory installed jumpers in their place e Add jumpers to the JP42 and JP43 jumper blocks located as shown in Figure 2 JP43 JP42 Figure 2 Location of JP42 and JP43 Jumper Blocks 2 2 Connecting the EVB to Your Computer The EVB communicates with your computer using a serial interface The EVB circuit board includes a DB 9 female serial connector which is labeled SERIAL PORT NOTE Do not confuse the SERIAL PORT connector with the adjacent FLEXCAN connector which also uses a DB 9 interface Attach the male end of a DB 9 serial cable to this connector Attach the other female end to the serial connector on yo2. Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document Freescale Semiconductor reserves the right to make changes without further notice to any products herein Freescale Semiconductor makes no warranty representation or guarantee regarding the suitability of its products for any particular purpose nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability including without limitation consequential or incidental damages Typical parameters that may be provided in Freescale Semiconductor data sheets and or specifications can and do vary in different applications and actual performance may vary over time All operating parameters including Typicals must be validated for each customer application by customer s technical experts Freescale Semiconductor does not convey any license under its patent rights nor the rights of others Freescale Semiconductor products are not designed intended or authorized for use as components in systems intended for surgical implant into the body or other applications intended to support or sustain life or for any other application in which the
3. EVB s flash memory You may now run the demonstration as described in Section 3 Running the USB Demonstration MCF5253 Evaluation Board Quick Start Guide Rev 0 Freescale Semiconductor 9 How to Reach Us Home Page www freescale com Web Support http www freescale com support USA Europe or Locations Not Listed Freescale Semiconductor Inc Technical Information Center EL516 2100 East Elliot Road Tempe Arizona 85284 1 800 521 6274 or 1 480 768 2130 www freescale com support Europe Middle East and Africa Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen Germany 44 1296 380 456 English 46 8 52200080 English 49 89 92103 559 German 33 1 69 35 48 48 French www freescale com support Japan Freescale Semiconductor Japan Ltd Headquarters ARCO Tower 15F 1 8 1 Shimo Meguro Meguro ku Tokyo 153 0064 Japan 0120 191014 or 81 3 5437 9125 support japan freescale com Asia Pacific Freescale Semiconductor Hong Kong Ltd Technical Information Center 2 Dai King Street Tai Po Industrial Estate Tai Po N T Hong Kong 800 2666 8080 support asia freescale com For Literature Requests Only Freescale Semiconductor Literature Distribution Center P O Box 5405 Denver Colorado 80217 1 800 441 2447 or 303 675 2140 Fax 303 675 2150 LDCForFreescaleSemiconductor hibbertgroup com Document Number M5253EVBQSG Rev 0 04 2007
4. Freescale Semiconductor Document Number M5253EVBQSG Rev 0 04 2007 MCF5253 Evaluation Board Quick Start Guide 1 Overview 1 1 Introduction Welcome to the MCF5253 Evaluation Board EVB The EVB features the MCF5253 microcontroller which is a part of the ColdFire family and includes a high speed Universal Serial Bus On The Go USB OTG module This module is USB 2 0 compliant contains an internal USB physical transceiver PHY with a USB transceiver macrocell interface UTMI and supports device and host mode 1 2 Purpose of this Document This document e Introduces you to the EVB components e Provides you with instructions for connecting the EVB to a power supply and to a computer e Guides you in running a demonstration of the EVB s high speed Universal Serial Bus On The Go USB OTG module Freescale Semiconductor Inc 2007 All rights reserved Contents OUGIMIEW ac choke rae Koh Gees AU E aees 1 INMOMUCHON i cis det oc aae nae taaas enka tina 1 Purpose of this Document 2 20s 0s60e ce wena 1 1 3 Components of the EVB 000 2 Preparing the EVB for Operation 3 Configuring the EVB Jumpers 3 2 2 Connecting the EVB to Your Computer 3 Running the USB Demonstration 4 Configure a Terminal Application for Viewing the EVB Output 4 32 Apply Power to the EVB wsic tenancies amine ae 4 3 3 Ensure Demo Sta
5. e USB Demonstration use CF Flasher to clear the EVB s flash memory and transfer the demonstration to it This section guides you through installing CF Flasher connecting the required hardware to use it and using it to transfer the USB demonstration application to the EVB flash memory 4 1 Installing CF Flasher To install CF Flasher on your computer 1 Start your computer and ensure that you are logged in with administrative privileges 2 Create a folder called cFFLAsHER on your desktop 3 Download CF Flasher from the MCF5253 Product Summary Page on the Freescale ColdFire Web site http www freescale com coldfire and save the files to the crrLasHER folder on your desktop 4 Open the crriasuer folder on your desktop and extract the contents of the CFFLASHER zip archive two applications crFlasher 3 1 setup exe and CF Flasher 3 1 M5208EVB patch exe to the same folder 5 Run the application cFFlasher 3 1 setup exe to begin installing CF Flasher and required drivers for the P amp E USB BDM interface 6 Accept all default options during the installation 7 When prompted restart your computer 8 Runthe application cr Flasher 3 1 M5208EVB patch exe to apply a necessary patch to CF Flasher MCF5253 Evaluation Board Quick Start Guide Rev 0 Freescale Semiconductor 7 The CF Flasher Tool 9 Accept all default options during the installation 10 If prompted restart your computer 11 Ensure
6. e cach write through sda lt 7 gt usb storage queuecommand called sdal sd 0 0 0 0 1 1 l is 1 PRPPRP PR 257 MB 257 MB Attached scsi removable disk sda Figure 5 Typical output of the insmod command r tmp mydisk t dev sdal tmp mydisk MCF5253 Evaluation Board Quick Start Guide Rev 0 ANSI SCSI revision 02 Freescale Semiconductor The CF Flasher Tool NOTE If your flash drive is formatted using a Windows based file system FAT or NTFS you may receive the message shown in Figure 6 This message does not affect the functionality of this demo VFS Can t find an ext2 filesystem on dev sdal Figure 6 Warning Message During the Mount Process 5 Type the following commands pressing Enter after each command to view the contents of the flash drive cd tmp mydisk ls 6 Type the following command to create a new empty file called newfile txt on your flash drive touch newfile txt Congratulations You have successfully used the high speed USB OTG module of the MCF5253 in host mode to communicate with a USB device 4 The CF Flasher Tool CF Flasher is a Windows based software tool that is used to program and erase the flash memory on the EVB The tool can be downloaded from the MCF5253 Product Summary Page on the Freescale ColdFire Web site http www freescale com coldfire If you have trouble running the USB demonstration application discussed in Section 3 Running th
7. epeat the steps in Section 3 4 Attach the Flash Drive to the EVB and Section 3 5 View Contents of the Flash Drive Using uClinux with another flash drive MCF5253 USB EHCI is found ehci ehci 1 EHCI Host Controller ehci ehci 1 new USB bus registered ehci ehci 1 irq 180 ehci ehci 1 USB 0 0 started usb usbl Product usb usbl usb usbl usb usbl hub 1 0 1 0 hub 1 0 1 0 ehci mcf5253 ehci SerialNumber ehci 1 USB hub found 1 port detected usb usb usb usb Product Cruzer Micro Manufacturer SerialNumber can t find transceiver probe of ehci 0 failed with error 16 ID 0x5 Rev 0x40 assigned bus number 1 io mem 0x80000600 EHCI 1 00 EHCI Host Controller Manufacturer uClinux 2 6 17 7 ucl ehci_hcd driver 10 Dec 2004 configuration 1 chosen from 1 choice 1 new high speed USB device using ehci and address 2 SanDisk Corporation 200443176107C3E0C684 4 Type the following commands pressing Enter after each command to mount the flash drive in uClinux mkdi moun usb usb scsi0 Vendor device v0781 p5151 is not supported configuration 1 chosen from 1 choice SCSI emulation for USB Mass Storage devices SanDisk Model Cruzer Micro Rev 0 1 Type Direct Access SCSI device sda 501759 512 byte hdwr sectors sda Write Protect is off sda assuming drive cach write through SCSI device sda 501759 512 byte hdwr sectors sda Write Protect is off sda assuming driv
8. failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application Buyer shall indemnify and hold Freescale Semiconductor and its officers employees subsidiaries affiliates and distributors harmless against all claims costs damages and expenses and reasonable attorney fees arising out of directly or indirectly any claim of personal injury or death associated with such unintended or unauthorized use even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part RoHS compliant and or Pb free versions of Freescale products have the functionality and electrical characteristics as their non RoHS compliant and or non Pb free counterparts For further information see http www freescale com or contact your Freescale sales representative For information on Freescale s Environmental Products program go to http www freescale com epp Freescale and the Freescale logo are trademarks of Freescale Semiconductor Inc All other product or service names are the property of their respective owners Freescale Semiconductor Inc 2007 All rights reserved lt p 2 freescale semiconductor
9. m Memory Window Erase Figure 7 The CF Flasher Main Window 3 Click the Target Config button The target configuration window shown in Figure 8 appears MCF5253 Evaluation Board Quick Start Guide Rev 0 8 Freescale Semiconductor EE _________v_v________ir The CF Flasher Tool M Target Configuration CPU 7 MBAR Ox z I Echo initialization sequence IPSBAR Ox z RAMBARO Ox z M Flash Algorithm _ lt none gt RAMBAR1 Ox z View Flash Info FLASHBAR Ox z BDM Communication m Flash z Flash Base Address Ox z Configure Figure 8 The Target Configuration Window Select the option M5253EVBE from the Target Configuration pull down menu 5 Select the option PE USB ML from the BDM Communication pull down menu Click the OK button to close the target configuration window and return to the CF Flasher main window 7 Click the Program button The Program window shown in Figure 9 appears m File Select N FileType SRecord Binary m File info Block s of Data Figure 9 The Program Window 8 Click the Browse button The standard Windows file browser appears 9 Navigate to the CFFLASHER folder on your desktop 10 Select the file m5253evb_flash s19 and click Open 11 Click the Program button The successful completion of these steps indicates that the USB demonstration has been properly transferred to the
10. nto the corresponding socket P2 of the EVB circuit board 4 Insert the electrical plug into an electrical outlet When the EVB is properly receiving power the green power LEDs on the circuit board glow 3 3 Ensure Demo Starts Properly After you apply power as described in Section 3 2 Apply Power to the EVB check that the following events occur 1 Your terminal application displays the startup message shown in Figure 3 MCF5253 Evaluation Board Quick Start Guide Rev 0 4 Freescale Semiconductor Running the USB Demonstration Hard Reset ColdFire MCF5253 on the M5253EVB Firmware v4c 1lb la Built on Nov 7 2006 12 11 38 Copyright 2006 Freescale Semiconductor Inc Enter help for help Press any key to stop autoboot 3 Figure 3 Demonsiration Startup Message 2 The last line in Figure 3 changes to reflect a three second countdown 3 Your terminal application displays a series of messages reflecting the boot process of the preinstalled uClinux kernel and drivers At the end of the process your terminal application displays information similar to that shown in Figure 4 NOTE You may need to press the Enter key to see the uClinux prompt shown in Figure 4 Starting syslogd and klogd sbin ifconfig missing unable to configure the network Setting system clock to RTC WARN Real time clock power loss Date information may be corrupt WARN Real time clock power loss Date information may be corru
11. pt Wed Feb 21 04 56 21 2007 0 000000 seconds BusyBox v1 00 2007 03 01 23 27 0000 Built in shell msh Enter help for a list of built in commands Figure 4 Typical Result of the uClinux Boot Process If these events do not occur it indicates the USB demo was not properly preloaded onto your EVB s flash memory Please see Section 4 The CF Flasher Tool for information on how to reload the demo into the EVB s flash memory 3 4 Attach the Flash Drive to the EVB Follow these steps to attach your USB flash drive to the EVB 1 Use the GE 6 in 1 USB cable and adapters to create a cable with the following connectors Mini A plug Standard A socket Attach the mini A plug of the cable to the mini AB socket on the EVB 3 Attach the USB flash drive to the standard A socket of the cable MCF5253 Evaluation Board Quick Start Guide Rev 0 Freescale Semiconductor 5 Running the USB Demonstration 3 5 View Contents of the Flash Drive Using uClinux Follow these steps to mount your flash drive and to access its contents using the uClinux command line 1 In your terminal application ensure the uClinux prompt is visible If it is not press the Enter key to display it 2 Type the following command and press Enter insmod lib modules 2 6 17 7 ucl kernel drivers usb host ehci hed ko 3 Observe the output in your terminal application and ensure it resembles the output shown in Figure 5 If it does not r
12. rts Properly 4 3 4 Attach the Flash Drive to the EVB 5 3 5 View Contents of the Flash Drive Using uClinux 6 The GF Flasher TOO vias dciek sci guncecetdhordears 7 installing CF Flashef cise coda os epee erkad an duge ta T 4 2 Connecting Required Hardware 8 4 3 Transferring the USB Demonstration to the EVB 8 e ae Z freescale semiconductor Overview 1 3 1 3 1 Components of the EVB EVB Kit Contents Figure 1 shows the components included in the MCF5253 EVB kit Please inspect your kit to ensure all components are present and undamaged If any of these components are missing or damaged please contact Freescale Semiconductor using resources available at http www freescale com support 1 3 2 Power adapter with plugs USB A B cable 6 P amp E USB BDM interface Figure 1 Components in the MCF5253 EVB Kit What You Need to Provide GE 6 in 1 Cable MCF5253 Evaluation Board Quick Start Guide this document Warranty Registration Card 920 75133 Technical Information Center Worldwide Contact List MCF5253 ColdFire Reference Manual M5253EVB User s Manual ColdFire Programmer s Reference Manual Additional components In addition to the components listed in Section 1 3 1 EVB Kit Contents you may also require the following components not included in the EVB kit Two standard circuit board jumpers A DB 9 serial cable male to female
13. that the icon CF Flasher 3 1 appears on your desktop If it does not repeat the steps in this section 4 2 Connecting Required Hardware CF Flasher communicates with the MCF5253 EVB through the provided P amp E USB BDM interface Follow the steps below to connect the proper components for CF Flasher to operate 1 Connect the standard A plug of the 6 USB cable to your computer 2 Connect the standard B plug of the 6 USB cable to the P amp E USB BDM interface 3 Locate the the BDM port labeled J12 BDM on the EVB circuit board 4 Connect the P amp E USB BDM interface to the BDM port on the EVB circuit board making sure that pin 1 on the interface as labeled on the tag near the connector aligns with pin 1 on the port 5 Ifthe EVB has not been connected to its power supply as described in Section 3 2 Apply Power to the EVB follow the instructions therein to apply power to the EVB 4 3 Transferring the USB Demonstration to the EVB The USB demonstration is stored as a flash memory image in the CF Flasher folder see Section 4 1 Installing CF Flasher Follow the instructions in this section to transfer this image to the EVB s flash memory 1 Ensure you have completed the steps in Section 4 1 Installing CF Flasher and Section 4 2 Connecting Required Hardware 2 Start the CF Flasher application The main CF Flasher window shown in Figure 7 appears CF CF Flasher loj xj Target Config Progra
14. ur computer If your computer does not have a serial port install a USB to serial adapter This adapter creates a virtual serial port on your computer and allows the EVB to communicate with the computer MCF5253 Evaluation Board Quick Start Guide Rev 0 Freescale Semiconductor 3 Running the USB Demonstration 3 Running the USB Demonstration The EVB is shipped with a sample uClinux based application preloaded in the EVB s flash memory which allows you to read the contents of a USB flash drive This application serves as one demonstration of the MCF5253 s high speed USB OTG capabilities Follow the steps in this section to run the demonstration 3 1 Configure a Terminal Application for Viewing the EVB Output Run a terminal application such as HyperTerminal to communicate with the EVB and to view its output Start the terminal application and set its communication parameters as shown in Table 1 Table 1 Terminal Communication Parameters Parameter Value COM port The PC port the DB 9 cable is connected to Baud rate 115200 or 19200 Data bits 8 Parity None Stop bits 1 Flow control None 1 If communication with one baud rate is not possible select the other baud rate 3 2 Apply Power to the EVB Follow these steps to apply power to the EVB 1 Select the appropriate plug for your electrical system 2 Connect the plug to the power adapter 3 Insert the power adapter s barrel plug i
Download Pdf Manuals
Related Search