KVM-9007 KVM Cat.5 Receiver
Contents
1. is foggy or un cleared on the screen 2 1 Please check if the VGA cable is properly connected Sometimes reconnect the cable may solve this problem 2 2 It is highly recommended to use Cat 5e cable when the connection is shorter than 150 meters and to use Cat 6 cable when the connection is between 150 and 300 meters Specifications Keyboard port USB Mouse port USB VGA monitor port 1 RJ 45 port 1 RJ 45 port connector 8P8C Local console port VGA blue HDDB 15 pin 3 to 1 cable connector to connect to PC LED Console port or PC port was selected VGA tuning Auto Adjusting Power adapter DC 9V 500 Weight g 360g Dimension mm 160 72 27 Resolution 1680 1050 150m 1280 1024 300m 10 Certification CE Certificate This equipment is in compliance with the requirements of the following regulations EN 55 022 CLASS A FCC This equipment has been tested and found to comply with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received Including interference that may cause undesired operation 29 C Fe2. D lt Lj H 0 On Hm m LevelOne KVM 9007 KVM Cat 5 Receiver User Manual Ver 1 00 0701 TABLE OF CONTENTS INTRODUCTION so deteriore decani OVERVIEW PEATURES ec ti EET a TE PACKAGE CONTEN Trara EEEE Da YR SE FRONT PANEL eee 1 2 3 4 REVISE PASSWORD WINDOW eene nnns 5 CONSOLE SATO 6 LOCAL PC PORT AND REMOTE PC PORT SWITCH 1 1 nennen nnne 7 BUZZER CONTROL si neta e Qe Rp e RAMS 8 SGAN PGO PORT Gale Mea ELE TROUBLESHOOTING SPEGIFIGATIONS 2 2 ERES CERTIFICATION EpL Introduction Overview Thank you for purchasing LevelOne KVM 9007 Cat 5 receiver KVM 9007 enables user to access the PC server or KVM switch up to 300 meters away from your keyboard VGA monitor and mouse It receives the signals from Cat 5 cable and converts them into signals of USB keyboard VGA and USB mouse respectively KVM 9007 can be used with KVM switch that has remote console port When working with KVM switch that has remote console port KVM 0831 1631 KCM 0831 1631 users are able to access KVM switch and control all the PCs which connected to
3. ight hand site of the Ctrl key oe 5 Lalt left hand site of the Alt key Ralt right hand site of the Alt key Lwin left hand site of the window key Rwin right hand site of the window key some keyboards might not have this key ae Uu es 1 Security To bring up the Security window 1 Power on 2 Press optional hotkey twice the press F4 key Note Default user name and password is 00000000 To close the Security window 1 key in a valid user name then press Enter key key in valid password then press Enter key 2 Press Esc key 3 Connect to a KVM device via Cat 5 interface Note 1 Available keys for user name and passwords are 0 9 a z no capital difference 2 Numbers on right hand site of the keyboard are not available to use 2 Help To bring up the Help window Tap optional hotkey twice then press F1 To close the Help window Tap any key on your keyboard 3 Hotkey OSD window To bring up the Hotkey window 1 Tap optional hotkey twice then press F2 2 In Help window tap F2 To close the Hotkey window 1 Press any key on your keyboard 2 Done the setup 4 Revise Password window To bring up REVISE Password window 1 Tap optional hotkey twice then press F3 key 2 In Help OSD window tap F3 key Note Before Revise Password window appears user has to enter the use
4. r name and password in Security OSD window 7 To close the REVISE window 1 Tap ESC key 2 Complete the USER NAME PASSWORD VERIFY setup 1 Default user name and password is 00000000 2 Available keys for user name and passwords 0 9 a z no capital difference 3 Press Enter three times gt to set up user name amp password as none 5 CONSOLE Status 1 First row shows remote console local console status 2 Second row shows hotkey mode e g The hotkey user selected now is Num Lock key To bring up REMOT LOCAL CONSOLE window 1 After complete SECURITY OSD window 2 Change remote local console mode 3 Press mouse left button then press ESC key To close REMOT CONSOLE window 1 Press any key on your keyboard 2 Press any button on your mouse 6 Local PC port and Remote PC port switch Press optional hotkey twice then press letter C T Buzzer control audio on off mode Press optional hotkey twice then press letter B 8 Scan PC port Scan Local port and Remote port VGA every 8 seconds Press optional hotkey twice then press letter S Troubleshooting 1 No video signal is displayed on the monitor 1 1 Please check if VGA cable and Cat 5 cable are properly connected to the connectors respectively 1 2 Make sure VGA cable is attached to computer during the boot up process 1 3 Make sure power adapter is connected to the receiver 2 Video signal
5. sh Auto detecting device on local port Select Button Select between local and remote side Rear Panel Bu me LOCAL HOST DC9v SOOmA CONSOLE RJ 45 DC power jack Connect power adapter Console port Connect to local monitor Local port Connect to local host PC RJ 45 port Connect to remote KVM switch or severs over Cat 5 cable Installation Connect to KVM switch with ACC 1000 Cat 5 console module 1 Attach the rubber feet to the bottom of KVM 9007 2 Connect keyboard VGA and mouse to the console port If you want to add a local PC connect local PC to the local host port with to 1 KVM cable ACC 2101 2102 2103 4 Connect one end of Cat 5 cable to the RJ 45 jack of KVM 9007 5 Connect the other end of Cat 5 cable to the remote console port ACC 1000 of the KVM switch KVM 0831 1631 KCM 0831 1631 6 Connect the power adapter to the power jack on the rear panel and the other side of power adapter connects to the power outlet OSD On screen display OSD gives you a convenient way to access and control the computers It includes management functions such as security language and help etc Note Caps Lock key is the default OSD hotkey the hotkey can be changed to other hotkey see OSD F2 Hotkey for details Hotkey operation 1 scroll scrolllock key num number lock key lt caps lock Lctri left hand site of the key Rctri r
6. the KVM switch from 300 meters away KVM 9007 is a good solution for those noisy server room environment where is unsuitable for people to work for a long time Besides it facilitates effective management on dispersive computers through one dedicated central control room demonstration room meeting room or at your desk Features KVM Cat 5 Cat 5e Cat 6 signal receiver from remote located KVM switches Extends transmits and receives KVM Cat 5 signals from up to 300 meters 1000 feet away Designed for application with KVM switches with built in remote console port Built in local host port to manage an additional computer directly connected installation with no additional software required Note It is highly recommended to use Cat 5e cable when the connection is shorter than 150 meters and to use Cat 6 cable when the connection is between 150 and 300 meters Package Contents KVM 9007 CD Maunal If any item is found missing or damaged please contact your local reseller for replacement Front Panel Power Adapter DC9V 0 5A Four Rubber Foot pad Console Port Connect USB keyboard and mouse Remote LED LED display X ndication Light off Remote port is not selected Light on Remote port is selected Light flash Auto detecting device on remote port Local LED LED display X Indication Light off Local port is not selected Light on Local port is selected Light fla
Download Pdf Manuals
Related Search