T10/T20/T30/T40 User Manual
Contents
1. 00W 380W 500W Model MPPT10 MPPT20 MPPT30 Mppt40 Battery standard voltage 12V 12V 12V 12V Battery capacity configuration 100AH 200AH 300AH 400AH Installation mm2 4mm2 8mm2 10mm2 12mm2 Installation Line AWG 10 AWG 8 AWG 7 AWG 6 AWG2. 232255 Toggle key Set parameters plus Set parameters Minus Manual switch load Long press and hold this button for 5 seconds to restore the factory settings error or system failure click this button you can troubleshoot or eliminate x 5 Parameter settings 5 seconds keystrokes parameters are saved automatically PV OFF LOAD OFF LOAD ON Evening Interval Dawn Set order automatic cycle Parameters setting Parameters setting This button can be manually open load or manually close the load Long press and hold this button for 5 seconds to restore the factory settings error or system failure click this button you can troubleshoot or eliminate x 6 Charging Problem Solution a No proper installation of solar panels cable polarity Removing the polarity you can re install the correct b More than the rated power of solar panels to reduce solar panel power does not exceed the rated power controller c Discharge Problem Solution d Removing the load is not properly connected to the load reinstall the correct e More than the rated load power to reduce load power the controller does not exceed the rated power f Instantaneous starting current is too large the battery capacity is too small the replacement of high capacity batteries button troubleshooting g Wire cable polarity loose or too square and increase r
3. YSmart Technology Co Ltd www ysmart tech com www chinasolarregulator com 86 755 85232255 T10 T20 T30 T40 User Manual This is a three time controller into the evening evening working time an interval of rest or pause time Dawn working time morning light function the user can according to their needs set a different time This is a compatible MPPT charge controller PWM intelligent efficient energy saving he not only has efficient MPPT controller charging function to automatically track the maximum power point 10 30 higher than the ordinary controller charging efficiency also has standby energy saving more than 30 energy than ordinary controller the standby power consumption of only 10mA 15mA 1 Product introduction T series of an intelligent multi purpose solar charge controller LCD screen display Battery reverse discharge protection Simple and more time control operation Battery reverse polarity protection MPPT PWM charging mode Battery under voltage protection Parameter user can reset Overload short circuit protection A key to open and close the load Automatic temperature compensation function A key to restore the factory settings USB5V charge current 500mA Optional 2 Installation Instructions Installation Installing wires first loosen the screw counterclockwise 1 Ready installation tools and materials and cable Please matching suitable cable 2 ensure that the current
4. charged voltage can be set Battery under voltage stop the supply voltage can be set Under voltage battery Load voltage is switched on again Evening H Load output state is set Set to 00H said that under the light control mode after dark dusk open load after dawn Dawn load to stop working Set to 24H represents the load has been open until the battery voltage protection automatically disconnects the load Set time 01H to 23H said under the next delay lighting control mode the load is loaded loaded loaded automatically after a delay before disconnecting a few hours in the evening and applications Expressed as the number of time delay Interval H An interval of time setting set this time Dawn to Evening to stop working load time Set to 00H indicates Evening to Dawn without the interval or intervals of 0H Set to 01H to 24H represents Evening to Dawn stopping power load time corresponding to the numbers indicate the length of time delay Dawn H Load output state is set the length of the second opening hours or workload Set to 00H means no load open or the length of time the load power 0H Set 01H24H said opening a load length of time numbers indicate the length of time corresponding to the open load YSmart Technology Co Ltd www ysmart tech com www chinasolarregulator com 86 755 85232255 Three time periods set cases Warning If night setting 00H or 24H time interval and dawn
5. density lt 4A mm2 This will help reduce the line pressure drop Check the installation site meets the relevant safety requirements avoid damp dusty flammable explosive and corrosive gases 3 Install the controller fixed to the vertical plane see Section V mounting aperture and hole spacing In order to ensure a good controller cooling conditions the controller on the bottom of each reserved 10cm space 4 As shown on the right wiring sequence load battery solar Battery plate is connected to the controller to be taken to ensure that the load battery The polarity of the solar cell panel and controller YSmart Technology Co Ltd www ysmart tech com www chinasolarregulator com 86 755 85232255 5 Before use external temperature sensor probe into the left of the controller temperature probe interface probe placed in similar battery temperature Line extension must be built in devices of the external temperature probe coextensive Otherwise the controller will control parameters of the temperature compensation of the error 6 Warning In order to prevent accidents from occurring install non professionals can not be engaged in loading and unloading operations 3 LCD operating interface description Charging Charging Fault Is discharging Discharge failure A A Solar charging current Ambient temperature Load current Battery capacity PV OFF V Load OFF V Load ON V Stop battery is fully
6. etightening bold cable h All keys can troubleshoot faults press 5 seconds to restore factory settings 7 Parameter table Parameters Model MPPT1 0 MPPT2 0 MPPT3 0 MPPT 40 Maximum power current 12A 20A 30A 40A Installation Lin mm2 4mm2 8mm2 10mm2 12mm 2 Installation Line AWG 10 AW G 8 AWG 7 AWG 6 AW G Weight 280g 300g 475g 480 Dimensions 143 89 46 mm 187 97 61 mm System load loss 13mA Loop Buck 100mV Battery float voltage 13 8V 12V system 27 6V 24V system Battery under voltage protection 10 6V 12V system 21 2V 24V system Battery under voltage recovery voltage 12 6V 12V system 25 2V 24V system Charge mode MPPT PWM MODE Operating Temperature 10 60 Storage Temperature 30 70 Humidity requirements 90 No condensation Temperature compensation 4mV Cell YSmart Technology Co Ltd www ysmart tech com www chinasolarregulator com 86 755 85232255 Temperature Probe built components NTC 100K thermistats Maximum open circuit voltage of the solar panel 18V 24V 12V system 36V 48V 24V system Solar panels maximum open circuit voltage V 48V 8 Cases 12V system standard configuration only applicable to our solar charge controller Maximum power voltage 18V 25V 18V 25V 18V 25V 18V 25V Peak power of solar panel 50W 130W 100W 260 2
7. would prohibit these two time periods set Evening 00H Interval H Dawn H After dark night open workload until dawn dawn load stops working Evening 24H Interval H Dawn H Normally open mode the load has been working until the battery under voltage automatic protection load stop working Evening 01H Interval 00H Dawn 00H Interval and Dawn are set to 00H after dark 1H off load after load of work can set Evening 23H Interval 00H Dawn 00H Interval and Dawn are set to 00H after dark 23H off load after load of work can set Evening 05H Interval 07H Dawn 03H Evening work load 5H interval to stop supplying the load 7H Dawn work load 3H can set Time Status Evening H Interval H Dawn H Set 00H Light control mode Setting prohibited Setting prohibited Set 24H Normally open mode Setting prohibited Setting prohibited Set 01H 23H Any value 00H 24H can set0 24 00H 24H can set0 24 Set 01H 23H Any value 00H No time interval direct execution of dawn working time 00H Load operating time 0H Set 01H 23H Any value 01H 23H Stop halfway load hours H 01H 23H Open the load again working hours H 4 Function keys YSmart Technology Co Ltd www ysmart tech com www chinasolarregulator com 86 755 85
Download Pdf Manuals
Related Search