Blacklight UV LED Light Bar
Contents
1. annan vana naa n annan vaene ne aa aaa e 9 SGH MOGO 9 DMX 00 000000 9 TECHNICAL 2 04000 00000000 10 2 20000000 0 0 00 navn avane enne aenea vanana naa anenna 10 SPECIFICATIONS 02 02 0 0 1 0 0 06660 001000000000 10 SAFETY WARNINGS AND GUIDELINES Do not expose this device to water or moisture of any kind Do not place drinks or other containers with moisture on or near the device If moisture does get in or on the device immediately unplug it from the power outlet This device is intended for indoor use only This device uses a grounded power cord and reguires a ground connection for safe operation Ensure that the power source has a proper ground connection Do not modify the plug or use a cheater plug to bypass the ground connection Ensure that the power outlet used to connect this device does not exceed the rated maximum voltage listed on the back panel of the device Ensure that power is turned off and disconnected before making any electrical connections Disconnect from the power source during lightning storms or when not in use Take care to prevent damage to the power cord Do not allow it to become crimped pinched walked on or become tangled with other c2. Technical support is available through the online chat button on our website www monoprice com during regular business hours 7 days a week You can also get assistance through email by sending a message to tech monoprice com TROUBLESHOOTING Following are some sample problems and potential solutions to those problems Q1 The light does not turn on and the menu will not display A1 Check the power cable to ensure it is properly plugged in Check the source power outlet by plugging in a different device Q2 The light does not respond to DMX commands 2 Ensure that the light is set to DMX mode with a valid DMX address Check for address conflicts with other devices Check the cabling to ensure that there is continuity between the light and the DMX controller Verify that there is a terminator at the end of the chain Verify that the DMX controller is operating properly with another DMX device SPECIFICATIONS Model 612610 Light Source 18x 1 watt UV LEDs DMX Channels 201 3 Beam Angle 45 Input Voltage Power Consumption 100 240 VAC 50 60 Hz 20 watts maximum Fuse FL1A 250V IP Rating IP20 Operating Temperature 4 104 F 20 40 C Dimensions 41 3 x 3 9 x 3 5 1050 x 100 x 90 Net Weight 4 6 lbs 2 1 kg 10
3. Use this menu option to set the starting DMX address 1 Press the MENU button to turn on the menu display Press the UP or DOWN button until Addr is displayed Press ENTER to select the entry for editing Use the UP and DOWN buttons to set the address value DMX Channel Selection Select the number of DMX channels to use See the DMX Control section for details on the two channel modes 1 Press the MENU button to turn on the menu display Press the UP or DOWN button until Chan is displayed Press ENTER to select the entry for editing Use the UP and DOWN buttons to select the number of DMX channels to use gt 2h MODES This light has three types of modes Automatic Sound Activation and Strobe Settings are retained when power is turned off Automatic Mode The light bar has an automatic pulsing mode which can be combined with a strobe Press the MENU button to turn on the menu display Press the UP or DOWN button until AUto is displayed Press ENTER repeatedly until SPxx is displayed xx can be any number Use the UP and DOWN buttons to set the speed of the pulsing function 5 Press ENTER until FSxx is displayed xx can be any number 6 Use the UP and DOWN buttons to set the speed from of the strobe from 0 off to 20 20 2 P O NN Sound Activation Mode The sound activation mode responds to musical content 1 Press the MENU button to turn on the menu display 2 Press
4. the UP or DOWN button until Soun is displayed m 3 Press ENTER twice to select the entry for KMH editing 4 Use the UP and DOWN buttons to set the sensitivity Strobe Mode 1 Press the MENU button to turn on the menu display 2 Press the UP or DOWN buttons until CoLo is displayed 3 Press ENTER repeatedly until Pxxx is displayed xxx can be any number 4 Use the UP and DOWN buttons to set the brightness level of the light 5 Press ENTER until SPxx is displayed xx can be any number 6 Use the UP and DOWN buttons to set the speed of the strobing effect from 0 no strobing to 20 20 2 NOTE Foruse as a stand alone blacklight always on without DMX set Brightness to P255 and Strobe to FS00 Slave Mode Only one fixture in each DMX chain can be the Master All others must be set to Slave 1 Press the MENU button to turn on the menu display 2 Press the UP or DOWN buttons until SLAu is displayed Sit Alu 3 Press ENTER to select Slave mode The display will read SLa MASTER SLAVE MODE Whenever the light is set to a mode other than a DMX address or Slave mode itis considered to be in Master mode For example when set to the Sound Activated operation itis in a Master mode When the light is the Master it will send DMX instructions to other connected lights Those other lights must be set to Slave mode SLAu to receive and execute the instructions sent by the Master light
5. Note Only one light in any DMX Universe can be the Master All other lights in the chain must be set Slave mode SLAu DMX CONTROL When the light is set to a DMX address it will respond to signals from a DMX controller The number and complexity of the signals it can respond to correspond directly to the number of channels selected The following tables show the functions and values for each channel in the two channel modes 2 or 3 2CH Mode Channel Value Function 1 0 255 Dimmer 0 100 0 11 No function i 12 255 Strobe 0 20Hz 3CH Mode Channel Value Function 1 0 9 No function 11 128 Auto mode 129 255 Sound activated mode 2 0 255 Sensitivity when in Sound mode pulsing speed when in Auto mode 0 11 No function i 12 255 Strobing speed DMX TERMINATION As with all DMX devices the last unit in any chain must have a DMX terminator connected to the DMX output If using just a single light connect a DMX terminator to the DMX output A DMX terminator is a DMX plug with a 120 ohm 1 4 watt resistor soldered between pins 2 and 3 TECHNICAL SUPPORT Monoprice is pleased to provide free live online technical support to assist you with any guestions you may have about installation setup troubleshooting or product recommendations If you ever need assistance with your new product please come online to talk to one of our friendly and knowledgeable Tech Support Associates
6. PRO AUDIO SERIES Blacklight UV LED Light Bar USER S MANUAL www monoprice com TABLE OF CONTENTS SAFETY WARNINGS AND GUIDELINES 4 00204000 0000 100 nna vananema 3 INTRODUCTION feecicccccccccceteecceeccuecavccscccaccuneucsuecsuccavecsdcvavcestessdeccvcesucceucustevstecsvecsvctevessuees 4 PACKAGE CONTENTS cecceecceccecceecceccuceceececcueccecceeaueceecaeeseecueeaeeseecaeeaeeeeecaeeneesaees 4 FEATURES anu a 4 MENU 2 0 0 0 00 00 0 aa eanae nav anaen ea 5 6 MENU 6 2 2 0 0 02000 0000000 6 BMX Ad ress aa 6 DMX Channel 0 nee ana naa v nne aav annan 6 MODES kira ananass lidthi 7 Automatic Mode cn 7 Sound Activation 2 00 0 0 00 7 Strobe 6 606000000000 0000 0 8 Slave 00 0 0 0 6660 000 8 MASTER SLAVE 2 171 01 1 06 600000000 8 DMX 2 2 2 020 0 000 000 00 0 9 2CH 2 2 0000 0 00000
7. es PACKAGE CONTENTS After receiving the product please inventory the contents to ensure you have all the proper parts as listed below If anything is missing or damaged please contact Monoprice Customer Service for a replacement 1x Blacklight UV LED Light Bar 1x AC power cable IEC 60320 C13 to NEMA 5 15 2x Mounting brackets 2x Bracket thumbscrews 1x User s manual FEATURES DMX512 Sound Activated and Master Slave control modes DMXinput and pass through connectors AC pass through connector e Black aluminum housing e Strobe speed and intensity controls e LED control menu MENU MAP REMA ELIA In EEH EN FEE EME FSO nl HETA EME shla 10 EF BEME FEDE FEE MENU SYSTEM Use the four buttons under the LED display to set the mode in which the light will operate The buttons perform the following functions MENU ESC Accesses the menu system or backs out of editing an entry UP Selects the next mode down in the Menu Map or increases the value of the selected mode DOWN Selects the previous mode up in the Menu Map or decreases the value of the selected mode ENTER Selects the currently displayed mode for editing or accepts the edited value MENU DETAILS For use as stand alone blacklight including always on without DMX turn to page 8 to enter Strobe Mode DMX Address Setup
8. ords When disconnecting the power cord do not pull on the cord itself Instead grasp the plug connector head to disconnect it from the power socket The power cord uses the US standard color coding with green for ground This device has no user serviceable parts Do not attempt to open service or modify this device Do not use chemical cleaners or solvents to clean the cabinet Use only a soft dry cloth For stubborn dirt moisten the cloth with warm water This device ventilates excessive heat through the slots and openings in the case Do not block or cover these openings Ensure that the device is in an open area where it can get sufficient airflow to keep from overheating Ensure that there are no flammable materials within 0 5m 20 inches of the light Do not connect this light to a dimmer This device has a pass through AC outlet which allows you to cascade multiple lights through a single power source connection When using 110 VAC level power do not cascade more than 40 lights If using 220 VAC level power do not cascade more than 30 lights INTRODUCTION Thank you for purchasing the Monoprice 612610 Blacklight UV LED Light Bar Please read this manual before attempting to operate the light This light accepts 110 240 VAC consumes only 20 watts of power It features a sound activation mode so it can automatically respond to musical content as well as predefined automatic modes It uses 2 and 3 channel DMX mod
Download Pdf Manuals
Related Search