i.Shine 3148 RGBW Color Stainer XP
Contents
1. ty ae Lodo bless webs Part 4 Troubleshooting 4 1 Troubleshooting list for some common electrical problems may happen during use Phenomenon Solution The fixture does not work No light out No Display Check main power fuse amp power cable connection Measure main voltage on the main connector The fixture does not work No display Check connection of display PCB Replace a new display INo responding to DMX controller Check working mode setting on display is DMX mode or not Check whether the unit be set as SLAVE Check DMX address settings Check DMX cable and it s connection Try to use another DMX console Signal error while use DMX Check whether DMX cables be connected well or not Check whether the DMX cable has to be terminated with a terminator to reduce signal errors If not please Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last fixture 4 2 Checking steps about why LED lamp not light Example Red led lamp not light Step 1 Disassemble lighting fixture and use multi meter to measure input voltage between R R on main PCB There should have DC48V Tf there no 48V voltage please check the electro circuit and parts such as CQ12 R39 R37 Q3 and etc If there have 48V voltage please go to step 2 Step 2 Check voltage between R2. Photometric Data Waterproof end cover of Safety chain fix parts Beam opening m 4 3 5 5 25 10 Distance rm 4 43 Diameter m 1 7 IMPORTANT ALWAYS READ THE USER MANUAL BEFORE OPERATION PLEASE CONFIRM THAT THE POWER SUPPLY STATED ON THE PRODUCT IS THE SAME AS THE MAINS POWER SUPPLY IN YOUR AREA _ This product must be installed by a qualified professional _ Always operate the equipment as described in the user manual _ A minimum distance of 0 5m must be maintained between the equipment and combustible surface _ The product must always be placed in a well ventilated area _ Always make sure that the equipment is installed securely _ DO NOT stand close to the equipment and stare directly into the LED light source _ Always disconnect the power supply before attempting and maintenance _ Always make sure that the supporting structure is solid and can support the combined weight of the products _ The earth wire must always be connected to the ground _ Do not touch the power cables if your hands are wet ATTENTION _ This product left the place of manufacture in perfect condition In order to maintain this condition and for safe operation the user must always follow the instructions and safety warnings described in this user manual _ Avoid shaking or strong impacts to any part of the equipment _ Make sure that al parts of the equipment are kept clean and free of dust
3. BLUE0 100 0 lt gt 255 CHS Cool White 0 100 0 lt gt 255 DMX Mode 6 ARCS MODE CHI Dimmer 0 100 0 lt gt 255 CH2 RED 0 100 0 lt gt 255 CH3 GREEN 0 100 0 lt gt 255 CH4 BLUE0 100 0 lt gt 255 CHS STROBE 0 100 0 lt gt 255 IDMX Mode 7 AR2S MODE CHI Dimmer 0 100 0 lt gt 255 CH2 RED 0 100 0 lt gt 255 CH3 GREEN 0 100 0 lt gt 255 CH4 BLUE 0 100 0 lt gt 255 CH5 Cool White 0 100 0 lt gt 255 CH6 STROBE 0 100 0 lt gt 255 DMX Mode 8 HSV MODE CHI IHUE 256 colors 0 lt gt 255 cH2 SATURATION 0 100 0 lt gt 255 CH3 VALUE 0 100 0 lt gt 255 2 2 4 Special construction for DMX connection _ At last fixture the DMX cable has to be terminated with a terminator to reduce signal errors Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last fixture _ Ifthe controller is 5 pin output it s necessary to use an adaptor to transfer signal from 5 pin output to 3 pin XLR plug or you can connect cables as following 3 pin XLR Pin 1 5 pin XLR Pin 1 GND 3 pin XLR Pin 2 5 pin XLR Pin 2 Negative signal 3 Pin XLR Pin 3 5 pin XLR Pin 3 Positive signal 5 pin XLR Pin4 amp Pin 5 not used 2 3 Master Slave Operation Color Stainer XP can be linked 10pcs together to work in Master Salve mode without any console The 1 machine
4. _ Always make sure that the power connections are connected correct and secure _ If there is any malfunction of the equipment contact your distributor immediately _ When transferring the product it is advisable to use the original packaging in which the product left the factory _ Shields lenses or ultraviolet screens shall be changed if they have become damaged to such an extent that their effectiveness is impaired _ The lamp LED shall be changed if it has become damaged or thermally deformed PART2 INSTALLATION 2 1 Mounting 2 1 1 Hanging The Color Stainer XP can be mounted in a hanging position using the supporting bracket The bracket should be secured to the mounting truss or structure using a standard mounting clamp Please note that when hanging the unit a safety cable should also be used 2 1 2 Upright The Color Stainer XP can be mounted in an upright or sitting position using the supporting brackets NOTE The Color Stainer XP can be mounted at any angle and in any position It is possible to further adjust the angle of the Color Stainer XP using the two adjustment knobs located on the side of the fixture 2 2 SETTING UP WITH A DMX512 CONTROLLER 2 2 1 DMX512 ADDRESSING WITHOUT ID ADDRESSING _ Connect the DMX512 controller to the units in series _ When set 10 dmx channel mode each unit will has 10 DMX channels so the DMX Addresses should increase by increments of 10 e g 1 11 21 31 _ The ID addr
5. and R on LED lamp PCB and it should be 48V Tf there has voltage but LED lamp not work the reason may be LED lamp short circuit or burnt Use a metal cable connect the two points which be marked with correspondent color such as R R G G B B to check whether it is short circuit one by one Tf there is no voltage that s mean the connection cable between lamp PCB and main PCB is short circuit and just need to replace that connection cable If there has voltage and no LED lamp burnt the problem might be some LED lamps on LED PCB not be welded well Check every led lamp and use a solder to re weld those not be welded led lamps Part 5 Maintenance The cleaning of internal must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the fixture s optics _ Clean with soft cloth using normal glass cleaning fluid _ Always dry the parts carefully _ Clean the external optics at least every 20 days _Clean the internal optics at least every 30 60 days Up to vary products Please ask professional technical to clean waterproof products and make sure the fixture will be reassembled well for waterproof 19
6. will be set as Master M f Cit Cy ow tI ai and others will work as Salve FTV unit at same effect PART 3 LED Display Panel Operation 3 1 Basic instruction MODE OVO O O MODE UP DOWN ENTER MENU menu selection or return to previous menu UP Press UP through the menu list to increase change the value of the current function DOWN Press DOWN through the menu list to decrease change the value of the current function ENTER Confirm amp Quit out current function setting 3 2 Display operation menu tree MENU gt 5IHOF felicia SF OF CLOSE SOFT mode E OFIT M i SF 01 Slow mode Fade in within 1 25 luri GFIGE SF 02 Fast mode Fade in within 0 6s E MODE lirue SF 03 Fade in at 0 6s Fade outat 1 25 rioja CEDO lira gt TIM FI gt 1 ix D DMX mode STAG 10channel Dimmer Red Green Blue White Color marco Strobe Autoprogram Auto program speed ID address D ARC 3 channel Red Green Blue AR2C 4 channel Red Green Blue White J ARCD 4 channel Dimmer Red Green Blue TA AR2D 5 channel Dimmer Red Green Blue White S ARCS 5 channel Dimmer Red Green Blue Strobe E AR2S 6 channel Dimmer Red Green Blue White Strobe HSV 3 channel HUE 256 colors Saturation Value 5 le Set DMX address between 1 512 via UP DOWN button gt ID OF Close ID ad
7. 0 lt gt 255 CH2 RED 0 100 0 lt gt 255 CH3 GREEN 0 100 0 lt gt 255 CH4 IBLUE 0 100 0 lt gt 255 CH5 Cool White 0 100 0 lt gt 255 0 lt gt 5 No function 6 lt gt 40 Red 41 lt gt 76 Green CH6 COLOR MACRO 7 preset color effect US ee Blue 113 lt gt 148 Yellow 149 lt gt 184 Cyan 185 lt gt 220 Purple 221 lt gt 225 White CH7 Strobe speed from slow to fast 0 lt gt 255 0 lt gt 5 No function 6 lt gt 36 Program 1 37 lt gt 68 Program 2 69 lt gt 100 Program 3 CH8 Auto program 8 programs 101 lt gt 132 Program 4 133 lt gt 164 Program 5 165 lt gt 196 Program 6 197 lt gt 228 Program 7 229 lt gt 255 Program 8 CH9 Program Fade in out time 0 lt gt 128 Program run speed 129 lt gt 255 CH10 IID ADDR 0 51 Group 0 lt gt 255 IDMX Mode 2 ARC MODE CHI RED 0 100 0 lt gt 255 CH2 GREEN 0 100 0 lt gt 255 CH3 BLUE0 100 0 lt gt 255 IDMX Mode 3 ARC2 MODE CHI RED 0 100 0 lt gt 255 CH2 GREEN 0 100 0 lt gt 255 CH3 BLUE0 100 0 lt gt 255 CH4 White 0 100 0 lt gt 255 DMX Mode 4 ARCD MODE CHI Dimmer 0 100 0 lt gt 255 CH2 RED 0 100 0 lt gt 255 CH3 GREEN 0 100 0 lt gt 255 CH4 BLUE 0 100 0 lt gt 255 IDMX Mode 5 AR2D MODE CHI Dimmer 0 100 0 lt gt 255 CH2 RED 0 100 0 lt gt 255 CH3 GREEN 0 100 0 lt gt 255 CH4
8. dress function 1D 1 50 Active ID address function Value at STAG mode ID channel value 10th channel between 0 4 all lights under control ID channel value between 5 255 lighting fixture with same ID address as selected at ID channel accept control only gt SILAVv e MASI Set Master Slave machine by UP DOWN SLAY MASI MAST Master machine mode not accept DMX from console Set it at AUTO mode to control other Slave machine amp gt SILIAV SLAV Slave machine accept DMX signal from console or Master machine CFIN Se juv Select scene 1 8 by UP button C F ON OFF current SCENE by DOWN button a EEE elj Edit current SCENE a 55 R 0 255 G 0 255 B 0 255 W 0 255 set expect color Ciao F Set SCENE fade time E 55 sa running time of current SCENE ay 55 Fade amp Running time maximum 9minutes and 59 seconds ENTE Example T 9 59 gt F 59 Use UP DOWN to adjust time Foco Press MODE to save setting and exit current menu gt T558 TIECT gt F In Test led brightness amp select spectrum color by UP DOWN gt 1 EIS i alll oko COL 0 Black COL 1 COL 7 EAT 1 Red 2 Green 3 Blue 4 Yellow 5 Cyan gt GLI 6 Purple 7 White TESS Display inside temperature 3 3 White Balance fine adjustment instruction Lup DOWN Ress sc im ACO
9. ess has not been set so therefore when using the controller CH10 must be inactive CH10 0 _ Each DMX Address may be used as many times as required _ Any DMX address in the range from 001 to 511 may be used 2 2 2 DMX512 ADDRESSING WITH ID ADDRESS _ Connect the DMX512 controller to the units in series _ When set 10 dmx channel mode each unit will has 10 DMX channels so the DMX Addresses should increase by increments of 10 e g 1 11 21 31 _ Each DMX Address may be used as many times as required _ Any DMX address in the range from 001 to 511 may be used _ Each DMX address may carry up to 50 separate ID addresses ID should be set in the menu on each unit in ascending values i e 1 2 3 _ ID addresses are accessible from Ch10 on the DMX512 controller at 10 channel dmx mode Example DMXADD 1 DMXADD 1 DMXADD 1 DMXADD 11 DMXADD 11 DMXADD 11 IDADD 1 IDADD 2 IDADD 3 IDADD 1 ID ADD 2 ID ADD 3 The figure above shows a simple DMX layout which has used three units at each DMX address The three units have different ID addresses which allows the user to collectively control the whole group of units at that DMX address by settingCH10 to 0 or to control each unit independently by first selecting the DMX address and then by using CH10 to select the target ID address 2 2 3 DMX Channel instruction Pa Function amp Effect DMX Value DMX Mode 1 STAG MODE CH1 Dimmer 0 100
10. i Shine 3148 RGBW Color Stainer XP USER MANUAL Thank you very much for choosing our product For safety purpose please read this manual carefully before your operation This manual included installation and using information Please install and operate it according to this manual 3148RGBW V6 0 05 15 2010 Indexing Part 1 Product GENERAL 1 1 PRODUCT INTRODUCTION 1 2 PRODUCT FEATURES 1 3 TECHNICAL SPECIFICATIONS 1 4 DIMENSION 1 5 EXPLODED VIEW 1 6 PHOTOMETRIC DATA 1 7 SAFETY WARNING PART 2 INSTALLATION 2 1 MOUNTING 2 2 SETTING UP WITH A DMX512 CONTROLLER 2 2 1 DMX512 ADDRESSING WITHOUT ID ADDRESSING 2 2 2 DMX512 ADDRESSING WITH ID ADDRESS 2 2 3 DMX Channel instruction 2 2 4 Special instruction of DMX connection 2 3 Master Salve Operation PART 3 LED DISPLAY PANEL OPERATION 3 1 Basic instruction 3 2 Display operation menu tree 3 3 White balance adjustment instruction PART 4 TROUBLESHOOTING 4 1 TROUBLESHOOTING LIST 4 2 Checking steps about why led lamp not light PART 5 MAINTENANCE Part 1 Product 1 1 Product introduction This product is designed for outdoor use Suitable applications include wash or effect lighting for architectural stage or nightclub applications This product can also be installed for use in signage and advertising using the dynamic functions available with DMX512 control Direct input of DMX512 signal allows the units to be controlled from any DMX512 controller This produc
11. t can be operated as a single unit or in multiple units for large applications 1 2 Product Features Optical system 1 256 grades electric adjustable mini within 100ms Strobe Adjustable speed same step strobe random electric strobe pulse strobe Working mode Standard DMX512 signal 3 4 5 6 10 channels 8 modes Intelligent ID addressing separately Intelligent ID group addressing Auto mode Master Salve Mode Display panel 4 LED digital display DMX address code test or play auto programs White balance adjustable Advanced New Function Set white balance via software to guarantee same bright color Self check inside temperature of lighting fixture Overheat auto protection Auto mode 8 preset color change scenes 1 3 Technical Specifications Voltage AC90 259v 50 60Hz AC230V 0 7A AC115V 1 4A IP rating P67 Power 158W Light Source 48 3W LED lamp Red 12pcs Green 12pcs Blue 12pcs Cool White 12pcs LED Lifespan around 30 000 50 000 hours Rated by LED lamp factory Beam angle 25 Optional 15 30 45 Case Die casting aluminum Net Weight 8 98Kg Size 289 x 237 x 306mm 1 4 Dimension Front Side Auld Anh e LR 1 5 Exploded View 1 6 Front Cover Power supply Faterproof PYC lens Power supply stand Main driving PCE Display PCB Cooling aluminium system for light beed 8 Joint part for light head amp set
Download Pdf Manuals
Related Search