User Manual
Contents
1. 0 Blackout Manual mode out of bounds through the mode 1 49 when the channel value is less than 5 the pattern size will shrink Manual mode out of bounds for the exhumation 50 99 mode when the channel value is less than 55 the Work Mode Selection pattern size will shrink CH1 12 Manual and sound mode out of bounds across the 100 149 mode when the channel value is less than 105 the pattern size will shrink Manual and sound mode out of bounds for the 150 199 exhumation mode when the channel value is less than 155 the pattern size will shrink 200 229 Auto mode 230 255 Sound Mode Pattern selection the value of a pattern 2 a total of CH2 13 Pattern Selection 0 255 127 pattern optional 0 63 Static adjust the size CH3 14 Zoom A dynamic size effect every 32 value period each to 64 255 different sizes in the same segment the larger the value the faster the operation 0 63 Static rotation adjustment The dynamic effect of the rotation each 32 value CH4 15 Rotation period each for a different effect of the rotation in the 64 255 same segment the larger the value the faster action 0 63 The static horizontal movement of the adjustment The dynamic effect of the horizontal movement each CH5 16 X axis rotation 32 value period each for different horizontal 64 255 movement in the same period the value the greater the faster action 0 63 The static vertical movement of the adjustment The dynamic v2. EVENT LIGHTING DGS Laser USER MANUAL For safety please read this user manual carefully before initial use Event Lighting reserves the right to revise the manual at any time Information and specifications within this manual are subject to change without notice Event Lighting assumes no liability or responsibility for any errors or omissions Please consult Event Lighting for any clarification or information regarding this item www event lighting com au V1 0 2 CONTENTS Safety Instructions Product Installation Rear Panel Control Board Operation Standalone Mode DMX Modes DMX Values IR Remote control Warranty Laser Emission Data Specifications Safety Instructions WARNING e Do not open this device there is no user serviceable parts inside Risk of electric shock e Do not look at the light source when the device is on e CAUTION This unit s housing may be hot during and after operation e Install this device in a location with adequate ventilation at least 20 inch 50 cm from adjacent surfaces e Do not leave any flammable material within 50 cm of this unit while operating or connected to power e Use a safety chain when mounting this device overhead e Do not operate this device outdoors or in any location where dust excessive heat water or humidity may affect it e Do not operate this device if the housing lenses or cables appear damaged e Do not connect this device to a dimmer or rh
3. LD 1 4 1 DMX input 3PIN Male XLR port using for DMX 2 DMX output 3PIN Female XLR port using for DMX 3 Digital display Display mode or address code 4 Safety Loop Attach the safety cable 5 Mic Sensitivity Knob Turn the knob potentiometer until the laser works in sync with the music To turn the laser effect laser diode ON OFF Be sure that only authorized 6 Key Switch operator hold the key 7 Buttons Choose Work Mode 8 Switch Switch on and off the power 9 Mains input With socket and integrated fuse holder CONTROL BOARD OPERATION Press the MODE button to enter the mode select state cycles display panel display AorS Soud AUTO d SLAV OFF six modes d mode press UP or DOWN key to select the DMX address Press the ENTER button to save the current operating mode or address code cc MODE UP DOWN ENTER OPERATING MODE DESCRIPTION DISPLAY MODE DESCRIPTION Auto switch between Auto Run Mode and As pee 6 nee Sound Active Mode depends on if the music exists or not Soud Sound Active Sd 1 Sd 6 Mode Sound Active Mode Auto Auto Run At_1 At 6 Mode Auto Run Mode eee DMX512 rene 7 d Control Mode Press UP or DOWN to Set the DMX address SLAV Slave Mode Slave mode OFF Standby Press MODE button or use IR controllor Mode to select another operating mode DMX CHANNELS DESCRIPTION
4. eostat e ONLY connect this device to a grounded and protected circuit e ONLY use the hanging bracket to carry this device e In case of a serious operating problem stop using immediately e The maximum ambient temperature is 104 F 40 C Do not operate this device at higher temperatures e Do not point this laser toward people or crowds e Do not point this laser toward any area where you or the operator do not know where the beams are being directed e Use aperture cover whenever not in use e Use the key to lock the laser to avoid unauthorised use e Avoid direct eye contact with laser light Never intentionally expose your eyes or others to direct laser light e This laser product can potentially cause instant eye injury or blindness if laser light directly strikes the eyes Power Input This device has an auto switching power supply work with input voltage range of 100 240 VAC 50 60 Hz Product Installation This device can be mounted in many orientations provided each individual device is secured by the use of correct mounting bracket This device should be directed above the heads of people and do not direct it toward the line of sight of people Refer to the diagram below Use a safety chain when mounting this device overhead 2 3 0 Meters Rear Panel 3 y E oe 8 fe Y MOD UP DOWN ENTER 9 A A A A 9D 4 oe 2 Ww y
5. ertical movement effect each 32 value CH6 17 Y axis rotation period each for a different vertical movement effect 64 255 in the same period within the larger the value the faster action CH7 18 Zoom 0 63 Static level of zoom adjustment Dynamic level of zoom effect every 32 values for some of each for different levels of zoom effect in the 64 255 same paragraph the greater the value the faster the action 0 63 The static vertical scaling adjustment Dynamic vertical zoom effect every 32 values for CH8 19 Scale some each for different vertical zoom effect in the 64 255 same paragraph the greater the value the faster the action 0 63 Regulation the static of getting painted CH9 20 Regulation A dynamic crescendo painted effect the greater the 64 255 value the faster the action The node definition the larger the value the sharper 0 127 the node CH10 21 Mode definition Only display node dot state the larger the value 128 255 the sharper the node 0 127 Static color choices the value of a 16 color schemes The color effect of the whole pattern of the same 128 191 color the larger the value discoloration the sooner GHz Zoom Pattern primary color based color effect the larger the value discoloration the sooner When CH22 192 255 value of 255 or 191 when the node will be the second pattern is the center point of the first pattern play more of the same pat
6. tern of the array IR REMOTE CONTROL DESCRIPTION POWER Power on or standby Mode AUTO Auto Run Mode SOUND Sound Active Mode WARRANTY Please refer to your local dealer or please contact Event Lighting LASER EMISSION DATA As measured under IEC measurement conditions for classification Laser Classification Class 3B Green Laser Medium DPSS Nd YVO4 KTP 532nm Red Laser Medium LD GaAlAs 650nm typical Blue Laser Medium LD InGaN 450nm typical Beam Diameter r lt 5mm at aperture Divergence each beam lt 12 mrad Divergence total light lt 90 degrees Laser Power 200mW 650nm Red CW 50mW 532nm Green CW 150mW 450nm Blue CW Transverse Beam Mode TEMO00 Scanning ILDA 20 Kpps SPECIFICTAIONS Mains Input AC100 240V 50 60Hz Fuse 250V 1 6A Slow Blow 20mm Glass Total Power 25W X Y Axis Beam Angle 20 Laser Safety Standard EN60825 1 2007 Condition Temperature 10 40 C DMX Connections 3 pins XLR Male Female Net Weight 1 35Kg Measurement 216mm x 160mm x 71mm
Download Pdf Manuals
Related Search