Schmitz OPX mobilis Operating Table
Contents
1. d T RES Wi DU I Ss function of the table top D Zi SCHMITZ Longitudinal shift function of the table top In order to adjust the longitudinal position of the table top press the release lever on the left hand side at the bottom of the back section to the inside out of its engage position and press the release lever and the hand grip together Shift the table top into the desired position let go of the release lever and shift a little further until the table top clicks audibly into position Danger Loi The patient lying on the operating table can get hurt by a sudden and unexpected moving of the table top which has not properly engaged into position Make sure after each adjustment procedure that the table top has properly engaged Check if the table top has properly engaged by slightly pushing the table top in longitudinal direction The table top must not move 37 The table top charged with the patient s weight can be shifted in longitudinal direction more easily if the table top is slightly inclined Operating table OPX mobilis EDITION 01 05 GB ID Nr 02007844 25 Operation Danger Loi Patients run the risk of getting hurt if the longitudinal shift function is activated with the table top in Trendelenburg or Reverse Trendelenburg position of2. Seat section Leg plate Pedal for brake D a and for directional castor Lf Y n T Selector lever gt 50 Potential equalization a ig Control panel Double castor for electric version In the following operating manual the terms left right front and rear are used as seen by a person sitting on the operating table in normal position Operating table OPX mobilis Enmon 01 05 68 ID Nr 02007844 11 Description of the operating table The operating tables OPX mobilis can be equipped differently depending on the model All operating tables are mobile They are equipped with four electrically conductive swivel type double castors with central brake The operating table models with a C in their type designation have got an additional directional castor All operating tables are equipped with mechanically operated hydraulic pumps The operating table of the 200 model series have got two hydraulic adjustment functions Height adjustment Raise Lower and Trendelenburg Reverse Trendelenburg The tables of the 300 model series have got an additional lateral adjustment function Operating tables with an E in their type designation are equipped with an additional electrically driven hydraulic pump In this case the operating table is equipped with a hand held remote control unit as well and with rechargeable batteries installed inside the floor pan Operating tables
3. hne GmbH amp Co KG Zum Ostenfeld 29 D 58739 Wickede Ruhr Telefon 02377 84 0 Amtsgericht Werl HRA 1431 Pers nlich haftende Gesellschafterin Gesch ftsf hrer Schmitz u S hne GmbH Amtsgericht Wer HRB 1477 Bemhard Schmitz Ludolf Schmitz Operating table OPX mobilis Epimon01 05 GB ID Nr 02007844 59 dT SCHMITZ Schmitz u S hne GmbH amp Co KG Postfach 1461 D 58734 Wickede Ruhr Zum Ostenfeld 29 D 58739 Wickede Ruhr Germany Phone 49 2377 840 Fax 49 2377 84162 http www schmitz soehne de e mail export schmitz soehne de Branch offices Spain SCHMITZ v S hne Ib rica S L Avda de Bruselas 58 semis tano E 28028 Madrid Phone Fax 34 91 7130000 Switzerland SCHMITZ AG Schloss Strasse 67 CH 8207 Schaffhausen Phone 41 52 6432505 Fax 41 52 6432691 SCHMITZ SA Francois Poncet Chemin de Veilloud 60 CH 1024 Ecublens VD Phone 41 21 6917466 Fax 41 21 6917462 France Sarl Schmitz France Za du Serroir 2 F 54690 Lay Saint Christophe Phone 33 3832 29467 Fax 33 3832 28238 The company reserves the right to alter the design construction dimension and finish of its products without notice
4. 48 Electromagnetic Immunity for Non Life Supporting 49 Separation distances soe RTI P de tuve nes V PR RA HER ETUR S Rat hw 50 Malfunctions and repairs zs racer Wiha SOLE DERE dede E DOVER ENSE ee es 51 IR 51 Spare PONS a cedet dd care sete oye eee o ee he EA Ae 53 Product designation neces 8 tiie dh bon bad De Ne oua Aer Add en ae 54 Nameplate Sises o rove nls EE 54 Symbols employed on the product 55 Technical data ico eR SEENEN re ERU MEQUE ESCAS Rb COP eade es 56 Classitication EE 58 Standards opplied der ie gba sk Gi Eet Vo Pee Ee UC DR RU RE NEU 58 Declaration of Co ntormity acc wale edge neces e dua t c bh rae EN e TOES 59 After UE ee 60 4 Operating manual Introduction About this operating manual In this paragraph you will find information about the layout of this operating manual and explanations regarding the marks and symbols used This operating manual includes instructions for the use of the operating tables OPX mobilis also called operating tables in the following Our products are constantly being improved this is why constructional changes carried out after printing of this operating manual could not be taken into consideration SCHMITZ In case of any questions we therefore kindly ask you to contact Schmitz u S hne This op
5. AG ml 36 Operating manual In order to attach the shoulder arthroscopy support push the plug in gudgeons into the reception holes at the seat section Make sure afterwards that the plug in gudgeons are properly locked The plug in gudgeons lock inside the reception holes In order to detach the shoulder arthroscopy support press the release buttons at both sides of the seat section and pull the plug in gudgeons out of the reception holes SCHMITZ Adjusting the inclination of the shoulder arthroscopy support In order to adjust the inclination angle of the shoulder arthroscopy support push the release lever up so that the gas springs are released Adjust the inclination angle of the shoulder arthroscopy support against the counter pressure of the gas springs As soon as the desired position is achieved let go of the release lever Operating table OPX mobilis 01 05 GB ID Nr 02007844 37 Operation Attaching and detaching the add on pads Mounting with locking bolt Release lever for adjustment of inclination angle In order to attach the add on pads push them from the rear into the recess so that the plug in sheet locks inside the mounting and the catching hook rests behind the fastening disc In order to detach the add on pad unlatch the plug in sheet by extracting the snap in bolt and then pull the add
6. and for the directional castor can have three different positions Ifthe pedal is raised the operating table will move in straight run An additional directional castor positioned below the height adjustment column is now touching the ground If the pedal is in mid position the operating table can easily be moved in any direction The directional castor is retracted If the pedal is pressed down the operating table is secured against unintentional movement Danger Patients run the risk of getting hurt when the operating table is moved while they are lying on top in knee elbow position Do not move the table with a patient lying on top in knee elbow position Danger Patients run the risk of getting hurt if the operating table is moved with an attached extension device due to its diminished stability against tilting Do not move the operating table with an attached extension device when a patient is lying on top In order to move the operating table in straight run raise the pedal completely In order to move the operating table easily in any desired direction raise the pedal into mid position Move the operating table into the desired location Secure the operating table afterwards by pressing the pedal completely down 16 Operating manual Potential equalization socket The operating table is equipped with a potential equalization socket You will find the potential equalization socket at the front side o
7. double castors with central brake and an additional directional castor Moving and locking the operating table Danger Loi Patients run the risk of falling off the operating table unless they are secured on the table top Secure the patient to the table top according to professional standards Move the table into the desired position and then turn the castors outwards in order to improve the stability of the operating table 37 The position of the castors will bear influence on the stability of the operating table L eg D Zi SCHMITZ Caution If the operating table is positioned on a moist or freshly cleaned floor please keep in mind that the frictional forces will be diminished The operating table may therefore be moved by external force even if the double castors are blocked Make sure before starting an intervention that the operating table is in a sufficiently stable position Operating table OPX mobilis Ebpimon01 05 GB ID Nr 02007844 Operation The operating tables except the standard model are equipped with an additional directional castor The directional castor can be activated by means of a foot pedal for the brake and for the directional castor Ge Selector lever W VEG Pedal for brake and for Foot pump lever directional castor The pedal for the brake
8. lever clockwise Then pull the clamping lever out against the spring force in order to unlock it Turn it back anti clockwise and let it engage again Turn the clamping lever clockwise once more Repeat the whole procedure until the arm rest is adjusted into the desired position e In order to release the ball and socket joint proceed in reverse order Turn the clamping lever anti clockwise Pull the clamping lever off against the spring force turn it back let it re engage and then turn it once more anti clockwise 34 Operating manual Add on kidney bridge The operating tables without integrated kidney bridge can be equipped with an add on kidney bridge The add on kidney bridge is attached to the operating table instead of the back section Attaching the kidney bridge n order to attach the add on kidney bridge remove the back section pad Insert the add on kidney bridge into the frame of the back section The locking pins in the frame will lock inside the cut outs at the bottom of the add on kidney bridge SCHMITZ The add on kidney bridge is now attached Caution In order to guarantee a gentle positioning of the patient when using the add on kidney bridge use an additional pad on top of the break This pad comes together with the kidney bridge Adjusting the add on kidney bridge The add on kidney bridge can be adjusted by means of a hand crank The crank can be
9. objects and people a Field strengths from fixed transmitters such as base stations for radio cellular cordless telephones and land mobile radios amateur radio AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy To assess the electromagnetic environment due to fixed RF transmitters an electromagnetic site survey should be considered If the measure field strength in the location in which the OPX mobilis operating table is used exceeds the applicable RF compliance level above the OPX mobilis operating table should be observed to verify normal operation b Over the frequency range 150 kHz to 80 MHz field strengths should be less than 3 V m Operating table OPX mobilis EDITION 01 05 GB ID Nr 02007844 49 Electromagnetic compatibility EMC Recommended separation distances Recommended separation distance between portable and mobile RF communications equipment and the OPX mobilis operating table The OPX mobilis operating table is intended for use in the electromagnetic environment in which radiated RF disturbances are controlled The user of the OPX mobilis operating table can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment transmitters and the operating table as recommended below according to the maximum output power of the communications equipment Rated maximum output Separation d
10. the selector lever Operating table OPX mobilis Enmon 01 05 68 ID Nr 02007844 21 Operation Adjusting the table top by means of the foot pump The functions of the hydraulic pump are preselected by means of the selector lever and the position of the table top is adjusted by means of the hydraulic pump The operating table models with electrically operated hydraulic pump are equipped with a selector lever each at the rear at the left and at the right hand side This way the operating table can be operated from the rear as well as from the left or right hand side Selector lever 3 Pedal for brake and for Foot pump lever directional castor n order to adjust the table top make the selector lever point to the symbol for the desired function Press the foot pump repeatedly until the table top is adjusted into the desired position RS In order to lower the table top other than for the other functions there is no need to pump the foot pedal It is sufficient to move the selector lever into Lowering table top position and press the foot pump lever only slightly The table top will sink automatically through its own weight 22 Operating manual Adjusting the table top by means of the electro hydraulic pump Operating tables with an E in their type designation are equipp
11. with an E in their type designation are equipped with rechargeable batteries Do not charge the batteries during a surgical intervention inside the operating theatre Danger Patients run the risk of falling off the operating table unless they are secured on the table top Patients lying on the operating table have to be secured to the table top according to professional standards Danger Patients run the risk of getting hurt when the operating table is moved while he or she is lying on top in knee elbow position Do not move the table with the patient in knee elbow position Danger Patients run the risk of getting hurt if the operating table is moved with an attached extension device due to its diminished stability against tilting Do not move the operating table with an attached extension device when a patient is lying on top Danger If an extension device is attached to the operating table its stability against tilting will be diminished Always use the props of the extension device during an operation Danger If patients are not positioned correctly there may be danger to their respiration to their nerve cords or to their circulation Always position patients in such a way as to prevent any possible danger to their respiration to their nerve cords or to their circulation A gt gt BP D Danger In case the components of the table top hit against an obstacle during adjustment the operating t
12. A U 24V DC SEA IP44 INT 1Min 4Min SCHMITZ Internal powered Zu 9 Wi de Wu CERO Medical Device 1 Mod Hr K Nr el S Nr D 58739 Wickede 135 kg uuum CE AOE Medical Device CI 1 Mod Nr K Nr m S Nr G models are marked accordingly Battery charger Ladeger t OPX mobilis Ir Mod Nr 2019686 ai C Ae IP67 SCHMITZ Schmitz S hne GmbH amp Co KG Medical Device Cl 1 c 2004 2005 2006 Tel Nr 49 2377 840 Beet Germany 1234567891011 12 54 Operating manual AT 17 SCHMITZ Symbols employed on the product Potential equalization socket Class AP device Observe the operating manual Do not activate the longitudinal shift function at a Trendelenburg Reverse Trendelenburg inclination angle of the table top of more than 5 Do not move the table when a knee rest is Do not move the table when an extension device is attached ep Operating table OPX mobilis Enmon 01 05 68 ID Nr 02007844 55 Technical data Measurements weights electrical data OPX mobilis 200 OPX mobilis 300 C OPX mobilis 300 C G OPX mobilis 300 CL OPX mobilis 300 CL G OPX mobilis 300 CE OPX mobilis 300 CE G OPX mobilis 300 CLE OPX mobilis 300 CLE G Total length w o head plate Total length incl head plate Width of table top Total width Base plate length x width Diameter of swivel type
13. EE Shaped head rest and connecting piece 101 270 Universal adaptor 101 188 Cushion semicircular 101 190 SE for operations on the intervertebral 101 520 Extension device 101 281 Cassette carrier for X ray cassettes 42 Operating manual SCHMITZ Cleaning and disinfection The pads at the seat and back sections are removable for easier cleaning Head section and leg plates can be removed completely This way they can easily be cleaned individually Cleaning For cleaning a weak alkaline cleansing agent may be used e g a mild detergent or soap suds fyour operating table is equipped with an electrically driven pump interrupt the recharging process of the batteries For cleaning raise the operating table to maximum height and move seat and back section into horizontal position If required remove the pads of the seat and back sections Attention The pads will get deformed when exposed to heat The operating table including its pads must not be sterilized by superheated steam Plastic components and pads of the operating table may only be cleaned using appropriate cleansing agents Attention Agents for disinfection of the patient s skin can cause discolourations on the pads Remove such disinfecting agents from the pads in order to avoid such discolourations 37 Do not employ machine driven methods of cleaning or disinfecting 23 Do not use scouring agents or solvents Clean the operat
14. Konformit tserkl rung Declaration of Conformity en D claration de conformit Ee Declaraci n de conformidad SCHMITZ Hersteller Producer Fabricant Fabricante Schmitz u S hne GmbH amp Co KG Das Produkt The product Le produit producto Typenbezeichung Beschreibung Type Reference Description Mod le r f rence description Tipo referenc a descripci n OPX mobilis Modell 161 201 205 161 311 315 161 321 325 161 331 335 161 341 345 Operationstisch Produkt Code gem Nomenklatur UMDNS Product Code from nomenclature UMDNS Code de produit selon la nomenclature de I UMDNS C digo def producto seg n nomenclatura UMDNS 13 961 auf das sich diese Erkl rung bezieht entspricht den Bestimmungen der Richtlinie to which this declaration Is in conformity and is in accordance with the provisions of the specific regulation auquel a rapport cette d claration correspond aux recommandations al cual hace referencia esta declaraci n corresponde las nomas Nr 93 42 EWG f r Medizinprodukte Klasse 1 gem Artikel 9 der Richtlinie for Madical Device Class 1 acc to art 9 of the specific regulation pour des produits m dicaux de la cat gorie 1 selon art 9 de la recommandation Para equipamiento m dico clase 1 seg n art 9 de las normas Ausstellungsdatum 24 05 2002 Date of Issue T Kr ger Sicherheitsbeauftragter f r Medizinprodukte L Schatz Schmitz S
15. Operating manual 28317 Operating table OPX mobilis SCHMITZ This operating manual includes instructions for the operation of the mobile operating tables OPX mobilis 200 161 201 OPX mobilis 200 G 161 205 OPX mobilis 300 C 161 311 OPX mobilis 300 C G 161 315 OPX mobilis 300 CL 161 321 OPX mobilis 300 CL G 161 325 OPX mobilis 300 CE 161 331 OPX mobilis 300 CE G 161 335 OPX mobilis 300 CLE 161 341 OPX mobilis 300 CLE G 161 345 Operating manual SCHMITZ Contents TEE 5 About this operating manual 5 Symibolsused inthe Text ck cee rte A x stek bate rd Nera dub OP ae SRG ERST EM E 6 Safety instructions coed V S ER eee bath bedded AE EE EE AE vd 7 Intended Uses ua RUE ones 7 Summary of safety instructions een 8 Description of the operating table annaa teen eee eee 11 COMMISSIONING vu skater 13 Keeping a aac dd EE Eet 13 Transportation ee OS Ss ERE oe OR SE eee ES 13 Unpacking ese rr sa 13 Electrical conriectl n cu a ERA ag s Be ee he Mek keen ER e UR ROLE lete OE 14 Operation cust mee he RAS Se td bas ey el Pbed rp ERES ER SE C PER e beu ee EA Qs 15 Mobility i tte sone hoi d e
16. R UR SERRA EMERG AMEE DA Ca Kv ni a ROLES A RARE ee n 15 Potential equalization socket lisse 17 Battety a E os sad sS be Gres Ree de Ae ge Rade Sas Grads at 18 Battery charger isses a unte RR RR Re UR OR RUN aot GE oa Rem ORI AU SUR RR REA 19 Adjusting the table top cecen ra senetan iia rrr 21 Longitudinal shift function of the joble jop 25 Integrated kidney bridge 27 Leg plates 4 23 dae oh LU e atiene qui oes al Ru S dor CERIS qd sed dae dab ie 29 plate eg A Lees aote Re RR OR REOR SGN CE ROULEAU CR OR RR RC RR CRT 31 B ck section ous e exe we S a E ERR URS RR de Sad Gaeta 33 Ami rest 101 107 4 4455 as Rp erer m ear ERU ete deg hh ee oe aie aed Eie ales 34 Add on kidney bridge llle 35 Shoulder arthroscopy support 36 Accessories for urology ss e eR AA Rega xA RARE A E EN Oe ERE aa 40 Further accessories of the Schmitz range 42 Cleaning and disinfection s 43 Cleaning TIT 43 Disinf chon sauer we SRG a EPR ew A E EE RA We FREUT E Euer EE ba 44 Operating table OPX mobilis Enmon 01 05 68 ID Nr 02007844 3 Contents Check psu catia nen tona dy burst tu Bt md ede ees ire tu canta NE Aaa ays 45 Electromagnetic Compatibility 2 6 I rra 47 Electromagnetic Emissions 47 Eledr m gnhetie ud aa m Did ala Ww eg stek aded edie e ERE reme nse
17. able may tilt Remove possible obstacles before adjusting the operating table or its individual components When folding the leg plate down make sure it cannot hit the floor Danger If its castors are released the operating table may move unintentionally during patient transfer Always secure the operating table by means of the central brake before transferring the patient Danger Patients run the risk of getting hurt by unforeseen movements of the table accessories When attaching accessories make sure that they are properly fixed Do not use worn or damaged accessories Danger Patients run the risk of getting hurt by unforeseen movements of the operating table Always secure the patient to the table top according to the recommended practices of patient positioning Danger When HF surgical equipment or defibrillators are being used there is danger of the patient s suffering burns if he or she touches the metal parts of the operating table or of its accessories or if he or she is lying on soaked sheets or cloths covering the electrically conductive pads of the table top Always observe the manufacturer s instructions for use Operating manual gt gt PG gt Danger Patients run the risk of getting hurt if the longitudinal shift function is released with the table positioned in Trendelenburg or Reverse Trendelenburg angle of more than 5 Reduce the inclination angle of the table top before a
18. able top is loaded mainly above the table column Familiarize yourself with the reactions of the operating table under this kind of charge before starting a surgical intervention Pads The operating tables are normally equipped with black antistatic pads Coloured pads which however are not electrically conductive are available upon special request The antistatic black version fulfils the limits of resistance according to ISO 2882 Coloured pads are not electrically conductive which means that in this case the operating table is not explosion proof Safety devices All operating tables are equipped with electrically conductive swivel type double castors with normally electrically conductive pads and with a potential equalization socket 12 Operating manual Commissioning Keeping Inside its original packing the operating table may be exposed for a period of 15 weeks to environmental conditions within the limits of Transportation Upon leaving the factory the operating tables are positioned fit for transportation In case of further transportation at a later date we recommend to adjust the operating table into the same positions Unpacking Carry the operating table if possible in its original packing to its final site of use Check the operating table s condition Any possible damage occurred during transportation should be reported immediately to Schmitz u S hne You will find their address and
19. an angle of more than 5 Reduce the inclination angle of the table top before activating the longitudinal shift function 37 In this connection please also observe the relative caution label above the release lever for the longitudinal shift function 259 Before using the operating table please make yourself familiar with its reactions when charged with a patient s weight 26 Operating manual Integrated kidney bridge Depending on the model the operating table can be equipped with an integrated kidney bridge The integrated kidney bridge is adjusted in height hydraulically by means of the foot pump of the table The kidney bridge provides the back section of the table top with an additional bulge The kidney bridge is designed in such a way as to allow the positioning of heavy weight patients If the kidney bridge is overloaded a pressure relief valve limiting the possible load responds when the kidney bridge is raised by means of the foot pump integrated kidney bridge Caution If the kidney bridge is raised to an extreme height this position will be uncomfortable for the patient In order to assure a gentle patient positioning do not raise the kidney bridge more than necessary and in case of an extreme raising of the kidney bridge use additional pads in order to position the patient in a gentle way SCHMITZ Raising the kidney bridge The kidney bridge is raised b
20. castors Height adjustment range Trendelenburg adjustment Reverse Trendelenburg adjustment Lateral adjustment both sides Range of longitudinal shift of the table top Back section adjustment Leg plate inclination Leg plate spread angle Head plate inclination totally Setting angle of head section pad Weight Nominal charge Maximum charge Pressure rating of the hydraulic system 720 to 1 080 mm 160 kg 720 to 1 080 mm 20 45 25 180 kg 1 780 mm 2 130 mm 540 mm 590 mm 980 x 545 mm 125 mm 740 to 1 100 mm 30 30 20 250mm 2 x 125mm 70 50 20 90 45 25 1 45 25 190 kg 135kg 185kg 120 bar 720 to 1 080 mm 20 45 25 200 kg 740 to 1 100 mm 20 250mm 2 x 125mm 45 25 210 kg 56 Operating manual SCHMITZ Measurements weights electrical data OPX mobilis 300 C OPX mobilis 300 C G OPX mobilis 300 CL OPX mobilis 300 CE OPX mobilis 300 CLE OP mobile 200 OPX mobilis 300 CL G mobilis 300 CE G mobilis 300 CLE G Applied part INT 1 min 4 min Protection against ingress of water Protection against the presence of flammable anaesthetic mixtures Fuses employed E models only Battery type employed type B amp According to European Standard 60601 2 46 the maximum admissible leakage currents meet the CF g requirement The appliance is not desi
21. ctivating the longitudinal shift function Danger If the operating table OPX mobilis is used in the presence of flammable anaesthetic mixtures the floor must be electrically conductive Caution The operating table is only stable on a level floor Choose a horizontal and safe site of installation for the operating table Caution In case the table top is adjusted into extreme positions there is danger of jamming one s finger in certain points Do not grab below the operating table or behind the frames of the table top elements Caution In order to ensure a gentle patient positioning when using the add on kidney bridge use an additional pad on top of the break This pad comes together with the add on kidney bridge Caution If the operating table is positioned on a moist or freshly cleaned floor please keep in mind that the frictional forces will be diminished The operating table may therefore be moved by external force even if the double castors are blocked Make sure before starting an intervention that the operating table is in a sufficiently stable position A IRS D Zi SCHMITZ Danger For tables with longitudinal shift feature the position of the table top will bear influence on the stability of the operating table Always shift the table top into such a position within the limits of the specific application as to improve the stability of the table If there is an extension device attached t
22. d onto the back section e Adjust the back section against the resistance of the gas spring or against the patient s weight and let go of the release lever as soon as the desired position is achieved The release lever will slide back into its original position and secure the position of the back section RS The reactions of the back section when being adjusted depend largely on the kind of charge exerted on the table top e g on the patient weight accessories attached or interchanged head and leg plates Please familiarize yourself with the reactions of the operating table when being charged with the patient s weight before using the operating table Attention If the operating table is being adjusted with the back section in folded down position the back section may hit the cladding of the mobile base and damage it This can also happen when the automatic 0 function is activated Always make sure that there is sufficient clearance below the table top before carrying out the adjustment functions Operating table OPX mobilis EDITION 01 05 GB ID Nr 02007844 33 Operation Arm rest 101 107 The operating tables can be equipped with arm rests The arm rest is fixed on top of a ball and socket joint The ball and socket joint is blocked or released by means of a clamping lever Blocking Releasing n order to block the ball and socket joint turn the clamping
23. der to prevent the electro hydraulic pump from accidentally being activated D Zi SCHMITZ LEDs indicating the preselected function SCHMITZ OPX mobilis tol long as the Run key is activated 1 0 3min a the Run key red LEDs indicate the battery capacity when The green LED is on as The I O key enables The Run key activates dg the electro hydraulic pump if it is enabled The green yellow and the main switch is switched on Operating table OPX mobilis Enmon 01 05 68 ID Nr 02007844 23 Operation Electromagnetic interference or other influences between the operating table and other electrical RS A appliances may cause failures or malfunctions Danger If the operating table OPX mobilis carries out unintentional adjustment functions e g due to an electric short circuit the I O key will serve as a panic button Switch the main switch at the control panel off as well Afterwards readjust the table using the foot pump and call the technical service e In order to adjust the operating table switch the main switch at the control panel ON The three lower LEDs now indicate the battery capacity When the battery capacity becomes insufficient the electro hydraulic pump can no longer be used However you can still adjust the operating table by means of the foot pump and recharge the batteries afterwar
24. ds You will find details under Charging the batteries on page 18 Make the selector lever point towards the desired function The LED in the corresponding symbol on the hand held remote control unit is on Press the I O key This key enables the Run key for a period of three minutes During this three minutes period several different adjustment functions can be carried out successively Press the Run key until the desired position is achieved When the operating table is adjusted to the desired position press the I O key in order to deactivate the Run key The Run key is deactivated automatically after a three minutes period in order to prevent an accidental activating of the electro hydraulic pump Press I O key again before readjusting the operating table 24 Operating manual Depending on the model the operating table can be equipped with a table top with longitudinally shift function By means of this feature patients can be screened with C arm equipment without the need to move them into a different position Shifting the table top in longitudinal direction Danger For tables with longitudinal shift feature the position of the table top will bear influence on the stability of the operating table Always shift the table top into such a position within the limits of the specific application as to improve the stability of the table
25. e seat section The lower plug is inserted into the cut out below the reception holes Push the leg plate in until it clicks into position and make sure that the leg plate is properly engaged Detaching the leg plates n order to detach the leg plate lift it slightly thus relieving it Press the release button and pull the leg plate off the seat section Operating table OPX mobilis Enmon 01 05 68 ID Nr 02007844 29 Operation Swivelling the leg plates outwards Toothing JD A L ere Ke T screw Caution Fingers or hands can get jammed if you grab the joint of the leg plate when carrying out the swivelling movement Do not grab the joint when swivelling the leg plate In order to swivel the leg plate outwards loosen the T screw Swivel the leg plate into the desired position A Danger The leg plate can come loose if the tooth system has not locked properly An unintentional swivelling of the leg plates can only be prevented if the tooth system is properly engaged Make sure the tooth system is interlocked when refastening the T screw Refasten the T screw while slightly moving the leg plate in order to make the tooth system engage Adjusting the inclination of the leg plates Release button In order to adjust the inclination of the leg plate press the release button at the leg plate Incline the leg plate against the
26. e under anaesthetics Any use apart or beyond these purposes is not intended The manufacturer is not D Zi SCHMITZ Always keep this operating manual at hand at the site of use of the operating table Additionally to the operating manual observe the general rules implied by the law and otherwise obligatory for accident prevention and environmental protection Do not carry out any modifications extensions or reconstructions of the operating table unless approved by the manufacturer Spare parts have to meet the requirements stipulated by the manufacturer This is always guaranteed when using original spare parts Observe the intervals prescribed or stated in this operating manual for periodical check ups Take care that running and process materials as well as parts replaced are disposed of safely and with minimum environmental impact liable for any damage resulting of such non intended use which would be entirely at the user s risk The operating table may only be handled by persons who have been briefed in its professional handling and who have familiarized themselves with the product by means of this operating manual Intended use also means following the operating manual and observing the conditions for inspection and maintenance Operating table OPX mobilis 01 05 GB ID Nr 02007844 7 Introduction Summary of safety instructions A A A A gt P Danger Operating tables
27. ected n order to detach the charging cable pull the front part of the plug back and pull the plug out of the socket Now the table top can again be adjusted with the aid of the electro hydraulic pump 133 With fully charged practically new batteries the table can carry out all its functions approx 60 times when charged by a patient weight 20 Operating manual Adjusting the table top All operating tables are equipped with a foot pump for adjusting the table top hydraulically A A Danger If patients are not positioned correctly there may be danger to their respiration to their nerve cords or to their circulation Always position patients in such a way as to prevent any possible danger to their respiration to their nerve cords or to their circulation Danger In case components of the table top hit against an obstacle during adjustment the operating table may tilt Remove possible obstacles before adjusting the operating table or its individual components When folding the leg plate down make sure it does not hit the floor The following table shows the functions which can be carried out by means of the hydraulic pump SCHMITZ Raising the table top Adjusting Reverse Trendelenburg position Lateral tilt left Lateral tilt right Adjusting Trendelenburg position Lowering the table top ni al IN ln The functions are preselected by means of
28. ed with an electro hydraulic pump and a hand held remote control unit The electro hydraulic pump can be activated by means of the hand held remote control Three LEDs at the hand held remote control unit indicate the battery capacity You will find details about how to charge the batteries under Charging the batteries on page 18 When the batteries are charged the functions of the operating table can be carried out by means of the electro hydraulic pump and activated by means of the hand held remote control The different functions are shown by means of symbols on the hand held remote control unit The function preselected by means of the selector lever is indicated by means of the LED in the relative symbol You can switch the functions of the hydraulic pump by means of the selector lever and read the preselected function at the hand held remote control unit When the main switch is switched on the LEDs at the hand held remote control indicate the battery capacity Now the Run key can be enabled for three minutes by pressing the I O key As long as the Run key is enabled the green LED in the I O key is illuminated For a period of three minutes the electro hydraulic pump can now be activated by pressing the Run key As long as the Run key is pressed the electro hydraulic pump will work and carry out the function preselected by means of the selector lever After three minutes the Run key will be deactivated in or
29. eless its use may inflict danger to life or physical safety of the user or of third parties or impairment to the operating table or to other material assets Do not use the operating table unless in perfect condition and only for its intended use with regard to safety and possible dangers and observing the operating manual Any malfunction which may affect the safety has to be eliminated immediately Electrically conductive double castors electrically conductive pads and a potential equalization socket are standard features of the operating table OPX mobilis It may be used inside rooms where the electrical installation conforms to German VDE i e the Association of German Electrical Engineers 0100 710 standard or to an equivalent national standard If the operating table OPX mobilis is equipped with non electrically conductive coloured pads it must not be used in the presence of flammable anaesthetic mixtures Intended use According to German VDE 0100 710 standard the operating table OPX mobilis may be used inside rooms of the application groups O 1 or 2 It is exclusively designed for purposes of human medicine The operating table serves to position patients during an examination or during surgical interventions The nursing staff has to take care to position the patients in such a way as to prevent any danger to their respiration to their nervous system or to their circulation This is especially important when patients ar
30. erating manual is to be read and observed by any person using or handling the operating tables OPX mobilis In addition to the operating manual and to the obligatory regulations for the prevention of accidents effective in the user s country and on the site of use the acknowledged rules for safe and professional work are also to be observed Operating table OPX mobilis 01 05 GB ID Nr 02007844 Introduction Symbols used in the text In this operating manual following designations or signs are used for pieces of information of special importance Danger A This symbol will appear wherever safety instructions are designed to protect people from physical harm The symbol stands for imminent danger of death or serious injury Caution This symbol will appear where situations are described which might be dangerous and which might inflict slight injuries Attention This symbol will appear in front of such hints which shall prevent the table or other equipment from being damaged IS This symbol will appear in front of additional helpful pieces of advice A dot in front of the text means This is what you have got to do Adash in front of the text means This is part of a listing Operating manual Safety instructions The operating table OPX mobilis has been constructed according to the latest state of engineering and according to the acknowledged rules of safety engineering Neverth
31. ews repair instructions or spare parts lists can be obtained upon request from Schmitz u S hne When ordering technical descriptions or spare parts at the manufacturer s kindly indicate the reference no the serial no and the project no of the operating table You will find these data on the nameplate of the operating table In the case of coloured pads please also indicate the ref no of the colour You will find the colour no on the back of the pads D Zi SCHMITZ Operating table OPX mobilis Enmon 01 05 68 ID Nr 02007844 53 Product designation Nameplates OPX mobilis 200 OPX mobilis 200 1 Mod Nr 161 201 GN am MZ NL Zur E Zum Ostenfeld 29 D 58739 Wickede Medical Device Cl 1 Tel Nr 49 2377 840 lade in Germany IP44 K Nr 0A S Nr OPX mobilis 300 C OPX mobilis 300 CL OPX mobilis 300 CL d Mod Nr 161 321 97 7 ONT CERO E OPX mobilis 300 C d Mod Nr 161 311 SCHMITZ Oz wie Schmitz Saho GmbH amp Co KG C RG ickede Medical Device CI 1 tet ties 449 2377 840 Made in Germany IP44 K Nr rd S Nr Zum re Wi Medical Device CI 1 IP44 e S Nr OPX mobilis 300 CE OPX mobilis 300 CLE OPX mobilis 300 CLE Mod Nr 161 341 I2 2A U 24V DC IP44 INT 1Min 4Min SCHMITZ Schmitz v S hne GmbH co ko Internal powered Zum Ostenfeld 29 OPX mobilis 300 CE Mod Nr 161 331 1 2
32. f the floor pan Danger Loi Patients may be exposed to danger by electrostatic tensions By means of the potential equalization socket electrostatic tensions are conducted to earth Always connect the potential equalization socket of the operating table to earth before use Before putting the operating table into operation connect the potential equalization socket to the earth connection A917 SCHMITZ Operating table OPX mobilis Enmon 01 05 68 ID Nr 02007844 17 Operation Battery If the operating table is equipped with an electro hydraulic pump this pump draws its energy from batteries installed inside the floor pan The batteries have to be recharged regularly in order to avoid an exhaustive discharge Danger Loi Plugging the plug of the charging cable in or out may produce sparks In order to avoid danger of explosion the batteries must not be charged inside the operating theatre during surgical interventions Charging the batteries IEN The batteries should be recharged regularly e g overnight The batteries cannot be overcharged if you use the battery charger which comes with the table Attention If the batteries of the operating table are charged by means of a battery charger other than the one supplied with the table the batteries may get damaged Always use the original battery charger for charging the batteries The hand held remote control unit is equipped with LED
33. gned for uninterrupted duty A 4 minutes interval is recommended after 1 minute s full load operation IPX 4 AP Q Fine wire fuses 5 x 20mm F1 10A time lag type F2 3 15A time lag type 4 pcs 6 V 12 Ah Input AC of the battery charger Output DC of the battery charger Internal fuses of the battery charger 90 V to 264 V 50 to 60 Hz mox 1 2A max 29 5VDC 2A Fine wire fuses 5 x 20 mm 2 pcs 0 4 A time lag type 1 pc 2 0 A time lag type Manufacturer Schmitz u S hne GmbH amp Co KG P O Box 14 61 D 58734 Wickede Ruhr Zum Ostenfeld 29 D 58739 Wickede Ruhr Germany phone 49 2377 840 fax 49 2377 84162 http www schmitz soehne de e mail Domestic sales dept zentrale schmitz soehne de e mail Exports dept export schmitz soehne de e mail After sales service service schmitz soehne de Under reservation of changes in construction and measurements Operating table OPX mobilis EDITION 01 05 GB ID Nr 02007844 57 Technical data Classification Class 1 medical device according to guideline 93 42 EC Standards applied The operating table OPX mobilis fulfils the requirements of following standards European Standard 60601 1 1990 A1 1993 A2 1995 European Standard 60601 1 2 2002 European Standard 60601 2 46 1998 European Standard ISO 14971 German VDE Standard 100 710 58 Operating manual D Zi SCHMITZ EG
34. ibed for this device The safety relevant check ups are legally prescribed in the operators ordinance and have to be observed Following check ups have been stipulated for the inspections Annually Checking the labels and the availability of the operating manual Visual inspection of the operating table and of the accessories with regard to possible damages Functional test of the operating table Checking the electrical safety according to German Standard VDE 0751 part 1 standard or alternatively according to European Standard 60601 1 1 repeat test Every five years Checking all hydraulic hoses and all hydraulic connections for possible damages Replacement of batteries in the case of operating tables with electro hydraulic adjustment functions E type models If defects are stated on the occasion of the safety check ups the operating table must not be used until these defects have been repaired SCHMITZ Operating table OPX mobilis Enmon 01 05 68 ID Nr 02007844 45 46 Operating manual SCHMITZ Electromagnetic compatibility EMC The following paragraph regarding electromagnetic compatibility only applies for the mobilis E model series mobilis 300 CE mobilis 300 CE G mobilis 300 CLE mobilis 300 CLE G Portable and mobile communication media using RF may interfere with electric medical appliances Electric medical appliances are subjec
35. ing table and its pads using a weak alkaline all purpose cleaning agent e g soap suds or mild detergents Dry moist spots on the operating table and on its pads Put the pads back into place Operating table OPX mobilis Enmon 01 05 68 ID Nr 02007844 43 Cleaning and disinfection Disinfection For disinfecting a commercial disinfecting agent for surfaces on an aldehydic basis may be used Caution N Disinfecting sprays may cause corrosion on mechanical parts or create explosive mixtures inside the table components For this reason do not use disinfecting sprays ILS Do not use disinfecting agents containing chlorine or agents hydrolysing chlorine Attention Agents for disinfection of the patient s skin may cause discolourations on the pads Remove such disinfecting agents from the pads in order to avoid discolourations Disinfect the operating table using a commercial disinfecting agent for surfaces on an aldehydic basis in a ready made weak solution The agent should be mentioned in the list of the DGHM i e the German society for hygiene and microbiology The list of the DGHM can be obtained from the publishers mhp Verlag Ostring 13 D 65205 Wiesbaden Germany 44 Operating manual Check ups Ageing wear and tear etc will affect the safety of the operating table As a preventive measure we recommend regular safety check ups The user has to carry out the safety check ups prescr
36. inserted on either side of the kidney bridge Due to a joint in the crank handle it can still be operated easily even if there are accessories attached to the side rails In order to adjust the add on kidney bridge insert the crank into its square end receptacle at the left or right hand side of the kidney bridge Turn the crank until the desired position of the add on kidney bridge is achieved and remove the crank again Operating table OPX mobilis Enmon 01 05 GB ID Nr 02007844 35 Operation Shoulder arthroscopy support The shoulder arthroscopy support is an accessory for the operating table series OPX mobilis Its intended use in combination with the operating table is the optimal patient positioning for interventions in shoulder arthroscopy In combination with the shaped head rest patient positionings for interventions in ophthalmology ENT or oral surgery are possible It is not intended to use the shoulder arthroscopy support for patient positionings in neurosurgery For these purposes there are special accessories at your choice The shoulder arthroscopy support may only be fixed to the seat section of the OPX mobilis It can be equipped with a shaped head rest or with a head plate of the Schmitz range by means of an appropriate connecting piece Attaching the shoulder arthroscopy support Danger Attaching the shoulder arthroscopy support to the back section will diminish the stability of the ope
37. is operating table is intended for use in the electromagnetic environment specified below Users of the OPX mobilis operating table should make sure that it is used in such an environment Immunity Test IEC 60601 Test Level Compliance Level Electromagnetic Environment Guidance Conducted RF Disturbance IEC 3 Vere Portable and mobile RF communications equipment should not be used at a closer distance to the OPX mobilis operating table including its power supply line than the recommended separation distance estimated using the equation applicable to the frequency of the transmitter Separation distance ToL d 22 80 MHz to 800 MHz 61000 4 3 150 kHz to 80 MHz 3y de 2 JP 800 MHz to 2 5 GHz Radiated RF Disturbance 61000 3 V m 3 V m 3 4 3 80 MHz to 2 5 GHz where P is the maximum output power rating of the transmitter in watt W according to the manufacturer of the transmitter and d is the recommended separation distance in meters m Field strengths from fixed RF transmitters as determined by an electromagnetic site survey should be less than the compliance level in each frequency range Interference may occur in the vicinity of equipment marked with the following symbol t Note 1 At 80 MHz and 800 MHz the higher frequency range applies Note 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures
38. istance according to frequency of transmitter power of transmitter m Ww 150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2 5 GHz Qe 052 rt 0 01 0 12 0 12 0 23 0 1 0 37 0 37 0 74 1 1 2 1 2 2 3 10 3 7 3 7 7 4 100 12 12 23 For transmitters rated at a maximum output power not listed above the recommended separation distance d in meters m can be estimated using the equation applicable to the frequency of the transmitter where P is the maximum output power rating of the transmitter in watt W according to the manufacturer of the transmitter Note 1 At 80 MHz and 800 MHz the higher frequency range applies Note 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people 50 Operating manual SCHMITZ Malfunctions and repairs In case of a malfunction please contact Schmitz u S hne You will find their telephone number on the last page of this operating manual Disposal Apart from the metal elements especially following components have to be disposed of according to the local regulations batteries hydraulic fluid electronic components foam pads bellows PVC floor pan ABS Operating table OPX mobilis Epimon01 05 GB ID Nr 02007844 51 Disposal 52 Operating manual Spare parts Technical descriptions such as circuit diagrams exploded vi
39. nd elbow rests which are fixed to the adaptor as well as a rinsing basin on swivel mounted support which is fixed to the side rail Rinsing basin on swivel mounted support The extension of the table top is exclusively designed for attachment at the seat section The extension of the table top may be charged with a weight of 100kg The rinsing basin on swivel mounted support can also be attached to the side rail in any other position Attaching the urological adaptor e In order to attach the urological adaptor insert its plug in gudgeons into the into the reception holes at the seat section Make sure afterwards that the plug in gudgeons are properly locked Danger Loi If a urological adaptor is attached the stability of the operating table will be diminished Raise the stability by moving the operating table into such a position as to make the double castors point in the direction of the urological adaptor Danger For tables with longitudinal shift feature the position of the table top will bear influence on the stability of the operating table Always shift the table top into such a position within the limits of the specific application as to improve the stability of the table 40 Operating manual A917 SCHMITZ Attaching the rinsing basin on swivel mounted support In order to attach the rinsing basin on swivel mounted suppor
40. o the operating table by means of a plug contact You will find the socket for the battery charger at the control panel at the left hand side of the floor pan The plug and the charging socket are marked by dots The plug will lock inside the charging socket if it is plugged into the charging socket with the dots in alignment IEJ The control panel is equipped with a covering sheet which is designed to protect the control electronics against electrostatic discharge current Fold this covering sheet up in order to get access to the control panel Plug the plug of the battery charger into the charging socket so that the marking dots are in alignment and press the plug in until it locks inside the charging socket Connect the battery charger to the mains power supply SCHMITZ LED green yellow or Den The operating modes of the battery charger are indicated by means of a 3 coloured LED Charging diagram Charging voltage current A current Voltage V Rapid charge Charge Compensation charge LED orange LED yellow LED green Electric 4 Charging 80 100 Capacity Operating table OPX mobilis 01 05 GB ID Nr 02007844 19 Operation If the batteries are drained it will take approx 8 to 10 hours to recharge them The batteries are charged as soon as the LED is green The battery charger can then be disconn
41. o the table or if the patient is positioned in knee elbow position the stability of the table will be diminished Improve the stability of the table by moving the table into such a position as to make the double castors at the foot end of the table point to the foot end I gt NDO Operating table OPX mobilis EDITION 01 05 GB ID Nr 02007844 Introduction IRS An unfavourable position of the double castors may diminish the stability of the table It may help to move the operating table in such a way as to raise the stability Please see the examples given in the illustration A patient weight of max 135 kg allows all surgical interventions to be carried out in either orientation of the patient patient s head lying at head or foot end of the table provided the castors of the operating table are blocked In the case of normal patient orientation and table top in mid position for operating tables with longitudinal shift function the operating table may be charged with a patient weight of max 185 kg Upon patient transfer or when letting the patient mount the operating table make sure that the table top is loaded mainly above the table column Familiarize yourself with the reactions of the operating table under this kind of charge before starting a surgical intervention 10 Operating manual 7 SCHMITZ Description of the operating table Head plate Back section
42. on pad out to the rear 38 Operating manual Attaching and adjusting the head plate or the shaped head rest The shoulder arthroscopy support is used in combination with a shaped head rest or a head plate The shaped head rest or the head plate are fixed inside the mounting by means of a connecting piece n order to attach the head plate or the shaped head rest insert the round rod of the connecting piece into the holder at the head plate or at the shaped head rest and tighten the clamping lever or the fastening screw Insert the square rod into the holder at the shoulder arthroscopy support and tighten the clamping screw n order to adjust the position of the head plate or of the shaped head rest loosen the gear toothed joint of the connecting piece Adjust the position of the head rest and tighten the clamping lever again Finally make sure that the joint is properly locked e Check the holders for the head plate or for the shaped head rest the hinging points of the gas springs the plug in gudgeons and the fastening discs for the catching hooks regularly for possible damages D Zi SCHMITZ Operating table OPX mobilis Enmon 01 05 68 ID Nr 02007844 39 Operation Accessories for urology In order to adapt the operating table for better use in the domain of urology it can be equipped with special accessories These are in detail an extension of the table top designated as urological adaptor a
43. p will again make the operating table carry out the adjustment movement preselected by means of the preselector lever Attention The kidney bridge may get damaged if it is slightly raised and at the same time charged with the full patient weight Make sure that the kidney bridge is completely lowered before letting the patient mount onto the table top Attention The pads are exposed to extraordinary wear when the back section of the table is raised as long as the kidney bridge is raised Do not raise the back section more than necessary as long as the kidney bridge is raised 28 Operating manual A917 SCHMITZ Leg plates Head plate and leg plates are fixed in the same Fixing the leg plates way so that leg plates and head plate are interchangeable This way the clearance below the table top can be varied Caution Interchanging the head and leg sections will influence the stability of the operating table as well as its reactions to adjustments In this connection please observe the hints regarding positioning of the castors on page 15 and regarding the position of the longitudinally adjustable table top on page 25 Reception hole Leg plate Please familiarize yourself with the reactions of the operating table when being charged with the patient n order to fix the leg plate push its bolt into the weight before using the operating table reception hole in th
44. points to the ceiling the patient can get hurt Always take care to make the lever point to the floor e n order to adjust the lever of the fixing screw pull it away from the head plate so that the lever disengages turn it into the direction desired and let it engage again 32 Operating manual Back section Caution When the table top is in an extreme position there is danger of jamming one s fingers in certain spots Do not grab below the table top or behind the table top frame Adjusting the inclination of the back section The back section is secured in its position by means of a gas spring with release mechanism After releasing the back section can be adjusted either against or with the aid of the resistance of the gas spring ch Hand grip back section adjustment OF A A917 SCHMITZ Danger When releasing the gas spring at the back section make sure to hold onto the back section as the force of the gas spring may cause the back section to jerk up or down and thus hurt the patient n order to adjust the angle of the back section press the release lever at the right hand bottom side of the back section from the inside out of ifs position and press release the lever and the hand grip together Make sure to hol
45. rating table The shoulder arthroscopy support should only be attached to the seat section Clamping screws Head plate Catching hook ri Add on pad oW 6 e AN s Y 5 P Joint Fastening S n m Fe EG Rel ase lever for adjustment of AN inclination angle Push in sheet e fc Clamping screw Bmw NS et NG A X Mounting with locking 5 bolt A Gas springs Danger The position of the table top for operating tables with longitudinal shift function will bear influence on the stability of the operating table If the relative application allows the table top should be adjusted in such a way as to raise the stability of the table If the arthroscopy support is attached the table top should be shifted as far as possible into the direction of the back section Danger The attached arthroscopy support will diminish the stability of the operating table Raise the stability by positioning the operating table in such a way as to make its double castors point into the direction of the centre of gravity
46. resistance of the gas spring and let go of the release button when the desired position is achieved The leg plate is now fixed again Attention When the operating table is being lowered as long as the leg plate is folded down the leg plate may hit the cladding of the mobile base and the cladding or the leg plate may get damaged Before lowering the table top make sure that there is sufficient clearance 30 Operating manual Head plate 137 Head plate and leg plates have got similar fixtures so that leg plates and head plate are interchangeable This way the clearance below the table top can be varied Caution Interchanging the head and leg sections will influence the stability of the operating table as well as its reactions to adjustments In this connection please observe the hints regarding positioning of the castors on page 15 and regarding the position of the longitudinally adjustable table top on page 25 Please familiarize yourself with the reactions of the operating table when being charged with the patient s weight before using the operating table Attaching the head plate In order to attach the head plate push the latch bolts into the reception holes until the head plate clicks audibly into place Check if the head plate has properly engaged Detaching the head plate Head plate Release button D Zi SCHMITZ 137 The head plate can be detached more easily if yo
47. romagnetic Environment Guidance Electrostatic Discharge ESD IEC 61000 4 2 6kV Contact 8kV Air 6 kV Contact 8 kV Air Floors should be wood concrete or ceramic tile If floors are covered with synthetic material the relative humidity should be at least 30 Electric Fast Transient Burst 2 kV on power supply lines 2 kV on power lines Mains power quality should be that of a typical commercial or hospital IEC 61000 4 4 1 kV on input output lines 1 kV on input output lines 2 environment SEN See mode UL mode Mainspower quality shoul be thatota IEC 61000 4 5 2 kV Common mode 2 kV Common mode Heer medal hospital voltage voltage environment Voltage Dips Short Interrupts and Variations on Power Supply Lines IEC 61000 4 11 lt 5 Ur gt 95 dip in Ur for 0 5 cycles 40 Ur 60 dip in Ur for 5 cycles 70 Ur 30 dip in Ur for 25 cycles lt 5 Ur lt 95 dip in Ur for 5 seconds not applicable Power Frequency Magnetic Fields 50 60 Hz IEC 61000 4 8 3 A m 3 A m Power frequency magnetic fields should be those of a typical commercial or hospital environment Note Ur is the AC mains voltage prior to application of the test level 48 Operating manual SCHMITZ Electromagnetic Immunity for Non Life Supporting Equipment Guidance and Manufacturer s Declaration Electromagnetic Immunity The OPX mobil
48. s The green LED is on when the batteries are fully charged The yellow LED will be on as soon as the batteries have to be recharged When the red LED is on the electro hydraulic pump can no longer be activated before the batteries have been recharged Ifthe red LED is on switch the main switch at the control panel off use the foot pump in order to adjust the table top until the operation is finished and recharge the batteries afterwards emn SCHMITZ o 9 o Chargi Main switch 133 The fuses for the electro hydraulic pump F1 10 A time lag type 5 x 20 mm and for the charging current F2 3 15 time lag type 5 x 20 mm are also inserted into the control panel 18 Operating manual Battery charger The battery charger is fit for a voltage input of between 90V to 264V It can be equipped with the feed cable corresponding to the requirements on site n order to charge the batteries move the operating table out of the operating area i The batteries cannot be charged as long as the main switch is on IS The charging current is up to 2A Make sure that the correct fine wire fuse 3 15A slow blow type has been installed inside the fuse holder F2 for charging current This is especially important for the more ancient models of the OPX mobilis range Switch the main switch at the control panel off The charging cable of the battery charger is connected t
49. t fix the vertical pole of the support to the side rail of the operating table by means of an appropriate fixing clamp Make sure that the clamp is properly locked Make the rinsing basin swivel into the desired position Attention In certain positions of the operating table the rinsing basin on swivel mounted support may get damaged Watch the movements of the rinsing basin on when adjusting the table top If required adapt the inclination angle of the rinsing basin to that of the operating table while carrying out the adjustment movements of the table top IS In order to raise the prestress of the hinge joints the caps of the joints can be removed and the screw underneath tightened by means of an Allen screw Operating table OPX mobilis 01 05 68 ID Nr 02007844 41 Operation Further accessories of the Schmitz range The operating tables can be adapted to special requirements by means of the ample range of accessories It is essential to observe the operating instructions of the relative accessories Among others following accessories may be used Ref No Designation 101 104 Arm rest 101 110 Arm hand operating table S Si Wristlets 101 127 Body restraint strap 101 145 Infusion rod 101 141 Anaesthetic frame 101 224 Leg supports G pel type 101 174 Shoulder lateral supports 101 182 Knee support 101 247 Rinsing basin with holder 101 161 d a various attachment clamps 101 166
50. t to special precautionary measures with regard to EMC They have to be installed and commissioned in accordance with the prescriptions regarding EMC as stated in this operating manual The models listed above are called OPX mobilis in the following Electromagnetic Emissions Guidance and Manvfacturer s Declaration Electromagnetic Emissions The operating table OPX mobilis is intended for use in the electromagnetic environment specified below Users of the OPX mobilis operating table should make sure that it is used in such an environment Electromagnetic Emissions Compliance Electromagnetic Environment Guidance The OPX mobilis operating table uses RF energy only for its internal functions RF Emissions CISPR 11 Group 1 Therefore its RF emissions are low and are not likely to cause any interference in nearby electronic equipment RF Emissions CISPR 11 Class B The OPX mobilis operating table is suitable Harmonic Emissions IEC 61000 3 2 Not applicable Voltage Fluctuations Flicker Emissions IEC 61000 3 3 Not applicable for use in all establishments other than domestic and those directly connected to the public low voltage power supply network that supplies buildings used for domestic purposes Operating table OPX mobilis EDITION 01 05 GB ID Nr 02007844 47 Electromagnetic Immunity Guidance Immunity Test IEC 60601Test Level Compliance Level Elect
51. telephone no on the last page of this operating manual SCHMITZ Ambient temperature 5 C to 50 C Relative atmospheric humidity 10 to 95 Atmospheric pressure 500 hPa to 1 060 hPa n order to transport the operating table adjust seat and back section into horizontal position Remove head and leg plates and detach other accessories Adjust the table top into minimum height Operating table OPX mobilis 01 05 GB ID Nr 02007844 13 Commissioning Electrical connection The operating table can be equipped with an electrically driven hydraulic pump In that case it is also equipped with a hand held remote control unit activating the electro hydraulic pump The hydraulic pump draws its energy from the integrated batteries If the main switch is switched on the battery state is indicated by means of the LEDs at the hand held remote control unit Hand held remote control unit Operating tables with an E in their type designation are equipped with an electro hydraulic pump and a hand held remote control unit The hand held remote control is connected to the operating table OPX mobilis by means of a plug type connector You will find the connector socket for the hand held remote control unit at the top of the height adjustment column The connector plug and socket are marked by dots The plug will lock inside the socket when the relative dots are brought in
52. to alignment Marking dots _ gt f y In order to connect the hand held remote control unit to the table insert the plug into the socket with the marking dots in alignment and plug the plug into the socket until it locks In order to disengage the hand held control unit draw the front part of the plug back Then pull the plug out of the socket Operating tables with an E in their type designation are equipped with rechargeable batteries Batteries The batteries have to be recharged as soon as the yellow LED on the remote control unit is on You will find details how to charge the batteries under Charging the batteries on page 18 The electric drive of the hydraulic pump can be activated additionally by means of the main switch You will find the main switch on the control panel at the left hand side of the floor pan The table top of the operating table can always be adjusted mechanically without electric drive by means of the foot pump IRS The electrically driven hydraulic pump of the operating tables with an E in their type designation has to be activated by means of the main switch 14 Operating manual Operation Mobility Depending on the model the operating tables OPX mobilis can equipped in different ways All operating tables are mobile Depending on the model they are either equipped with four double castors with central brake four
53. u press against the head plate thus relieve it and only then press the release buttons In order to detach the head plate press the head plate from the rear against the reception holes Press the release buttons at the left and right hand frame of the back section either simultaneously or one after another and pull the head plate off the back section Adjusting the inclination of the head plate Release lever Head plate Raise the release lever e Adjust the inclination of the head plate against the resistance of the gas spring and let go of the release lever as soon as the desired position has been achieved Operating table OPX mobilis 01 05 GB ID Nr 02007844 31 Operation Adjusting the inclination of the head section pad Head section pad Attention If the loosened fixing screw is re inserted the wrong way on edge its thread can get damaged upon fastening Therefore loosen the fixing screw only as little as necessary e n order to adjust the inclination of the head section pad loosen the fixing screw at the head plate Caution There is danger of jamming ones fingers under the head section pad When loosening the fixing screw grab into the cut out in order to adjust the inclination angle of the head section pad e Adjust the head section pad into the required angle and re fix the fixing screw Caution If the lever of the fixing screw
54. with an L in their type designation are equipped with a table top with longitudinal shift function By means of this feature such parts of the patient s body can be screened which under normal circumstances are inaccessible to the C arm equipment Operating tables with a G in their type designation are equipped with an integrated kidney bridge The integrated kidney bridge is adjusted hydraulically by means of the foot pump All operating tables can be equipped with X ray cassettes which can be inserted below the table top either from the head end or from the foot end All operating tables can be adapted optimally to various applications by means of accessories According to the regulations of European Standard 60601 2 46 the operating tables are designed to carry a maximum patient weight of 135kg In case a higher charge is intended please observe the instructions given below 133 A patient weight of max 135 kg allows all surgical interventions to be carried out in either orientation of the patient patient s head lying at head or foot end of the table provided the castors of the operating table are blocked gt In the case of normal patient orientation table top in mid position for operating tables with longitudinal shift function the operating table may be charged with a patient weight of max 185 kg Upon patient transfer or when letting the patient mount the operating table make sure that the t
55. y means of the foot pump of the operating table The switch lever serves to switch the hydraulic system into activate kidney bridge mode and back to normal operation of the table top adjustment functions Foot pump lever A D integrated kidney bridge Foot pedal for central brake and for directional castor Preselector lever Raise the switch lever into top position by the tip of your foot The kidney bridge can now be adjusted in height by means of the hydraulic foot pump of the table Raise the kidney bridge up to the desired height using the foot pump Make the switch lever return into mid position In order to do so you can also shortly press the lever fully down It will then automatically return into mid position when released Operating table OPX mobilis 01 05 GB ID Nr 02007844 27 Operation Lowering the kidney bridge The kidney bridge can be lowered in height anytime without having to use the foot pump Caution Before lowering the kidney bridge make sure that there are no body members or objects in the area between the kidney bridge pad and the frame of the back section Press the switch lever for the kidney bridge completely down against its spring force until the kidney bridge is lowered down to the desired position Release the switch lever The lever will return automatically into mid position and activating the foot pum
Download Pdf Manuals
Related Search