"user manual"
Contents
1. the lamp replace with a new one of the same characteristics Gx9 5 lamp holder Then reinsert first the pins the lamp into the socket by pushing Make sure the lamp is properly held Finally close the projector front access and the front access fastener see 7 in figure 2 Connect the spotlight and check that the lamp is functioning properly 5 3 Lens replacement Before proceeding to change the lens make sure that the projector has not been running recently because it could be hot if so let it cool for a few minutes To change the lens open the front access fastener see 7 in figure 2 The lens installed is at your right An iron ring is placed around the lens Remove it with the help of a tool to pry it open WARNING The ring holds the lens be careful not to fall it down Tilt the projector and remove the lens you can press it by the outside to help it out Insert the new lens To improve the quality of the light beam be sure of its cleanness Finally reinsert the steel ring for holding the lens correctly Close the front part of the projector and fasten it see 7 in figure 2 Verify that the light beam of the new lens is correct User manual STR 650 1000 F PF 12 6 Most common problems Problem Usual Cause Solution Unit does not start No current reaching the Check mains connections unit Lamp does not work Replace the lamp following the instructions of Maintenance If the problem persists despit2. 5 Maintenance WARNING Before touching the projector surface make sure that it has not been on recently because it can operate at high temperatures with a risk of burns 5 1 Regular cleaning To prevent the growth of dust and dirt which may impair the proper operation of the equipment it should be cleaned regularly For cleaning it use a soft slightly and damp cloth if the equipment is very dirty apply a little liquid detergent to the cloth WARNING Do not use solvents or products containing alcohol Make sure that no liquid get inside the equipment The lens cleaning must be made with a soft cloth Water may be used but dry it with a dry cloth to remove all traces of water and dust 5 2 Lamp replacement Before proceeding to change the lamp make sure that the spotlight has not been running recently because it could be hot if so let it cool for a few minutes Lamp replacement begins by turning anticlockwise the focal adjustment nut see 9 in figure 2 till reach its maximum position Then open the front access fastener see 7 in figure 2 and the lamp can be seen inside the projector Carefully remove the lamp from the socket holding it by the plastic part WARNING Do not touch the glass of the lamp because it could affect the service life of the product If during the installation you touch the lamp glass wipe with a cloth moistened with alcohol User manual STR650 1000F PF 1n When you remove
3. Technical data Power supply Single phase 230V 50Hz Lamps T 12 650W T 11 1000W Lamp holder Gx9 5 Aperture angle Minimum 10 Maximum 63 Lens 150 mm Aluminium reflector 99 9 quality 34100 mm Power supply cable 3x1 5mm 1metro Maximum projector temperature 160 C Minimum distance to objects 2 m at the light beam Maximum room temperature 40 C Weight 5 5 Kg Dimensions 360x334x276 mm User manual STR 650 1000 F PF 4 1 3 Photometric data _ Projection distance Aperture es PA ange _ AA Diameter Fig 1 Light beam Projection Aperture Diameter Luminance Ix aiai slo O 6 User manual STR 650 1000 F PF 5 1 4 Dimensions 1 Filter holder fastener 2 Filter holder lid 3 Handle User manual Fig 2 4 Fastening knob 5 Filter holder 6 Safety grille STR 650 1000 F PF oO000000Q0000 PEBANAAAAA 7 Front access fastener 8 Orienting handle 9 Focal adjustment nut 2 Accessories The accessory range consists of the following products e STR 650 1000 V Barndoor e STR 650 1000 PF Filter holder Dimensions 180x185 mm Weight 0 15 Kg User manual STR 650 1000 F PF 3 Installation ATTENTION Before touching the spotlight surface be sure that it has not been working recently due to the high temperatures of the projector while working because you risk burning yourself For the same reaso
4. USER MANUAL STR 650 1000 F PF Index 1 General desc pOr os 3 E sa wocoits en a A 3 ala Soe A a ty aan eee ee teat 4 13 Photometie NA erences re co ei cay giants ieee vice pie 5 14 DIMENSIONS cisnes lisa E EAE 6 2 ACCESSOFIES tdo 7 Se Installation IPP O Un o te hee ut ita aa tee ha 8 3 1 Power supply connection nt ad 8 3 2 Colour filter installation seen 9 4 Opera Maa feel hane A aes 10 4 1 Aperture angle adjustment sssseeeeeeerrn renerne 10 5 Maintenance ld ica 11 5 1 Regu lar cl aniNg sssini iii 11 5 2 Lamp paco Me iii 11 A 11 6 Most common problems il dci did 13 Statement of Compliance id 14 User manual STR 650 1000 F PF 2 1 General description THEATRE lighting family of Strong is composed of a set of projectors for 650W or 1000W lamps For this reason they are appropriate in facilities where high power lighting is required for instance theatres showrooms etc STR 650 1000 F PF is a lighting projector with pressed fresnel lens Moreover this range includes some accessories which increase the functions of the projectors 1 1 Characteristics Focal adjustment is included by endless screw and back knob Made of aluminium profiles and iron plate Painted with black oven dried epoxy Metal filter holder and safety grille are provided with the spotlight Lamp not included STR 650 1000 F PF reference is 21000002 User manual STR 650 1000 F PF 3 1 2
5. e these measures please contact to FRESNEL s Technical Service Department Tel 34 93 274 54 28 Tel 34 93 360 02 30 Fax 34 93 274 47 47 If you want to do without this product do not mix it with the ordinary waste There are specific methods and systems for dividing electronic and electromagnetic used products that are described in 2002 96 EC directive which is in force in the European Community countries User manual STR 650 1000 F PF 13 FRESNEL S A DC 01 STATEMENT OF COMPLIANCE DATE 01 01 12 We declare that the product Mark STRONG Models STR 650 1000 F PF Year of construction 2012 Conforms to the following EC directives 2006 95 EC In relation to the safety requirements for material intended for use within specific voltage limits 2004 108 EC In relation to the electromagnetic compatibility of equipment systems and installations Sole administrator ngel Torrecillas Red n Barcelona January 1st of 2012 Fresnel S A C Potos 40 08030 Barcelona Spain Tel 34 93 360 02 30 Fax 34 93 274 47 47 strong strong es http www strong es User manual STR 650 1000 F PF 14
6. f the unit disconnect it from the current The spotlight is power supplied when connecting the supply hose to a 230 volt 50 hertz single phase mains with ground Before connecting the spotlight you must be sure that the voltage supplied is correct 3 2 Colour filter installation WARNING Use colour filters suitable for the temperatures that can reach this lighting projector This projector incorporates a holder for colour filters see 5 in figure 2 To install a filter move the filter holder fastener see 1 in figure 2 by pushing it laterally Simultaneously rotate 180 the filter holder lid see 2 in figure 2 Then insert the colour filter in front of the safety grille so that it is placed between the inner grooves Finally proceed closing the filter holder lid in the same way as for the opening User manual STR 650 1000 F PF 9 4 Operation The projector can be positioned manually varying the inclination To do this loosen the fastening knob see 4 in figure 2 and position it by holding the back plastic handle see 8 in figure 2 Be careful not to touch the metal parts because the focus can reach high temperatures To fix it again turn the fastening knob clockwise until fixed it 4 1 Aperture angle adjustment The spotlight angle and consequently the diameter of the light beam can be changed by turning to right and left the focal adjustment nut see 9 in figure 2 User manual STR 650 1000 F PF 10
7. n fix the projector away from inflammable surfaces First of all you must be sure that the distance between the projector and the closest object in the light beam should be greater than 2 meters Otherwise the object could reach high temperatures which could damage it lt is also recommended placing the projector at 0 2 meters away from any object around it As well do not put the unit closed to objects which could emit heat such as heaters and radiators The unit is not prepared for working in wet environments relative humidity greater than 90 So it can not work under raining conditions It must be positioned for not interfering with its proper ventilation This projector is equipped with a handle see 3 at figure 2 to allow to fast it at tube structures and surfaces The projector handle can be turned and braked by a knob that allows the proper orientation of the device The spotlight must be fixed at a point completely stable and capable of supporting the weight of the equipment 5 5 kg via the handle attaching it to this point with the anchor holes Always use M12 steel screws to set the spotlight Once the projector is hanging vertical inclination can be adjusted by the lateral fastening knob see 4 in figure 2 Unscrew it to orientate the projector and screw it when you consider that the light beam is correct User manual STR 650 1000 F PF 8 3 1 Power supply connection During handling and installation o
Download Pdf Manuals
Related Search