Gas Range User`s Manual
Contents
1. Model C9GRA4GVE1 CIGRA4GVU1 C9GRAGGVE1 C9GRA4E1 Dimension mm 80979007 800 x 900 x 1200 x 900 x 800 x 900 x 850 60 850 60 850 60 850 60 Oven Chamber Size mm 540670275 540670275 540670275 Pressure Pa 2800 3200 2800 3200 2800 3200 2800 3200 a ai ra 2 92 2 16 4 33 1 6 Type Pressure Pa 2000 2000 2000 2000 nS je 4 09 3 37 6 07 2 54 Power LPG 35 25 8 51 8 19 2 kW NG 38 8 31 8 57 5 24 Gas Inlet Size R1 3 4 R1 3 4 R1 3 4 R1 3 4 3 2 Non Basic Model For gas range mainly user can choose different combination in accordance with actual requirement For the total power please refer to the nameplate Bima Power KW Gas Consumption NG LPG NG M3 H LPG KG H Big Burner 2 crown 9 9 0 95 0 75 Big Burner 1 crown 7 5 5 6 0 79 0 47 Middle Burner 4 5 4 0 48 0 33 Small Burner 3 5 2 8 0 37 0 23 3 2 1 Big Burner with 2 crown Ree oS OS AAA E 4 Precautions amp Recommendations 4 1 Transportation and Storage During transportation the machine should be carefully handled and do not put it upside down to prevent from damaging to the shell and inside The packaged machine should be stored in a ventilated warehouse without corrosive gas If it needs to be stored in open air temporarily measurement against raining is needed 4 2 Notice for Installment 1 10 11 The appliance can be installed as a countertop type Also you can dismantle the 4 legs and then scr2. point At this time hold the knob and push down the igniter simultaneously to light up the pilot flame Initial ignition may be a little longer due to the air existing in the pipeline The pilot flame can be normally ignited when the air is exhausted completely e After ignition release the knob 20s later e Turnthe knob to MAX ormin according to food requirements 3 Flameout Press down the control knob and turn it clockwise to e e Turn off the main gas supply 4 Replacing the Main Nozzle Picture 4 e Have involved tools prepared e Dismantle the burner frame gas ring burner base and take out the basin then remove the nozzle and substitute it with a matched one e Fasten the nozzle and replace the basin burner base gas ring and burner frame in order e As for oven take apart the lower panel of the oven door and discharge the nut and nozzle holder with an appropriate spanner then substitute with a matched nozzle e Fasten the nozzle and detect for leakage then seal the panel 5 Replacing the Pilot Nozzle Picture 4 e Place a proper spanner on the nut of the pilot support to balance the twisting stress Discharge the screw fixing the thermocouple with a straight screwdriver then remove the thermocouple e Discharge the nut fixing the aluminum pipe and remove the pipe Remove the pilot nozzle and replace with an appropriate one It is unnecessary to regulate the primary air Adjusting the P
3. CIGRA4GVE1 CIGRAGGVE1 CIGRA4GVU1 CIGRA4E1 Gas Range Luxury Gas Range Series User s Manual Dear Client amp User Firstly thanks for purchasing and using our product All the information and guidelines of this user s manual comply with certain applicable regulations which come out from our long term accumulated knowledge and experience as well as current project development situations Limited to some special structures additional specified items or new technology changes the actual usage situation might be some different from what stated in this user s manual Should you have any question please do not hesitate to contact the manufacturer via the method shown in back cover page of this manual For safety purpose and efficient operation please make this document available to users for reference Do have them to read this manual carefully before carry out any action on this device especially when starting The manufacturer declines any responsibility in the event users do not follow the instructions or guidelines stated here The user s manual should be placed close to the device in convenience of users reading before operation We have the full authority to reserve the further technical changes of the device in the scope of further performance improvement characteristic development IN Warning The appliance is only applicable to low pressure gas During using users must use low pressure gas pressure reducin
4. ance stable and level Do not tilt or sway during operation Before installation remove the outer plastic film first Clean the residues on the stainless steel sheet with appropriate substance Check that the appliance is pre set to use the gas family available at the place of installation Make sure the supply gas is the same with the gas that the appliance allows to use 12 13 14 15 16 17 18 Do not use gas that not applicable to the appliance as fuel neither does high pressure or medium pressure regulating valve This appliance is only applicable to low pressure regulating valve Before installation a quick acting disconnecting valve should be installed upstream the appliance where is easy to reach Making sure the applicable gas is the same as the supplied one If not stop using Pipeline connected to the appliance should be connected with a metal pipe fitting and make sure that there is no leakage If the pressure of the gas pipeline is 15 higher or lower than the rated pressure the appliance required a regulator should be installed to ensure it reaches the rated value After connecting the appliance to the gas system check for leaks at joints and pipe fittings to do so use soapy water or a specific leak detector spray No Flaming Checking gas supply pressure after installation Gas supply pressure can be measured with a liquid filled pressure gauge for example a U shaped pressure gauge minimu
5. er reference or left for the next operator authorized to use the appliance Please keep the integrity of the appliance and remove the outer package If you have any questions consult specialist and stop using the appliance To avoid danger keep the packaging materials away from children For the materials are plastic bags nails etc This product is a commercial machine that needs to be operated by experienced technician Do not leave the appliance unattended To avoid danger turn it off if necessary Maintenance must be done by professional technicians with original accessories If this requirement cannot be observed it may affect the safety performance of the appliance This machine is only for commercial use not applicable for other usages Or it may cause hazard Do not aim at the appliance with water jet during cleaning That may damage the components e g electrical equipment and control valve etc To prevent surface oxidation and chemical interaction the stainless steel surfaces should be cleaned appropriately and regularly Perfect performance and longer service life of the appliance is guaranteed by correct installation professional operation and continuous maintenance 5 Working Instructions amp Operation Flow 1 Control Knob e e j e e RER l A SERR a f a A o Fig 1 Fig 2 Fig 3 Fig 4 2 Ignition Press down the control knob and rotate it counterclockwise to align Ao with the zero salient
6. ew the body with the cabinet but first you should have a matched cabinet Take out the attached battery turn the pulse button counterclockwise then put in the battery in the correct direction as shown and tighten the pulse button Components used for appliance connection should comply with provisions in gas safety installation and operation The appliance should be installed separately or assembled with other device in stated range The appliance is not suitable for built in installation otherwise the appliance may work in hypoxia condition emission of the combustion products may be out of limits and it may cause health problems even death The appliance should keep a minimum clearance of 10cm away from walls Do not install the appliance on flammable floor or materials If it is installed on the countertop the countertop should be made of refractory materials to ensure safety of the operators and normal operation of the appliance During installation please consider the weight of the appliance It is advisable to install on the floor or countertop The appliance should be installed in a well ventilated area if possible under a vent hood in compliance with all applicable regulations in force This will ensure that all burnt gases produced during the combustion process are completely exhausted Otherwise the accumulated waste gas may do harm to people s health even cause serious injuries or death After installation keep the appli
7. g valve instead of high or medium reducing valve Any self modification wrong installation adjustment or maintenance can lead to property loss or casualty Please contact the manufacturer for any adjustment or maintenance and have the work done by a trained amp qualified person For your safety sake please keep the machine away from any liquid gas or other object which is flammable or explosive For your safety sake walls and countertops in the mounting position of the appliance should be made of refractory materials to ensure safety of the operators and safe operation of the appliance Do not modify the air inlet and smoke vent required for combustion Otherwise it may cause safety accidents This appliance is designed for food cooking To avoid hazard pay attention to the water level in pan do not dry heat the utensil or let the food inside spill over Fire warning If you smell the gas please keep away from any fire source Do not light up any device or touch the electronic switch Do not use any phone in the building either Close the main gas valve immediately and call the professional personnel to maintain it Control knob of the gas valve should be operated with hands only do not use any tools to control the knob If it cannot be rotated with hands do not do it by force or attend to fix it Operate by force or maintain improperly will lead to large gas leakage or deflagration easily The manufacturer won t bear any responsibili
8. ilot Nozzle Place a proper spanner on the nut of pilot support to balance the twisting stress Discharge the bolts at bottom of the support with a straight screwdriver Unscrew the screws in the support counterclockwise to adjust the flame Regulate the primary air according to gas type pilot nozzle _ injector Picture 4 Note Gas leakage must be checked after regulating the pilot nozzle and replacing the main nozzle 6 Routine Inspection It is necessary to check the machine daily Check the machine regularly can avoid serious accident happens Stop using if user feels that there are some problems in the circuit or machine Check the situation of the machine before or after using every day Before using Whether the machine is tilted Whether the control panel is damaged During using Whether there is strange odor or vibration noise 7 Whether the burner flame is normal Any light back or flameout Whether the power is normal Cleaning amp Maintenance Before using remove all commercial grease Clean the superficial grease with a towel then rinse it with mild detergent and water Do not use abrasive detergent to clean the appliance surface neither do scrape it with steel wire brush or sharp utensil that may cause damage Do not spray the furnace surface with water directly nor do clean it with corrosive substance acid alkali For burner cleaning detergent remained on burner surface and in fire ho
9. le should be removed completely Otherwise it may cause a short time flameout or incomplete combustion even affect the safety performance of the appliance or do harm to personnel health If not going to use the appliance for a long period of time cut off the gas supply clean the furnace surface with a gasoline cloth store it in a well ventilated area General inspection should be carried out at least once a year by professional personnel 90 of the appliance is made of metal stainless steel iron aluminum galvanized metal sheet which can be recycled by appointed treatment plant according to the environmental standards of the equipment installed countries in force No littering 8 Failure Analysis amp Trouble Shooting Symptoms Causes Solutions The pilot flame cannot be lit up Pressure in gas pipeline is not enough The nozzle is blocked Connection of thermocouple is loose The thermocouple is defective The gas control valve is defective ar on gt Regulate the reducing valve Unblock the nozzle Tighten the thermocouple Replace the thermocouple Replace the gas control valve The pilot flame is on but the main burner cannot be lit up Pressure in gas pipeline is not enough Main nozzle is blocked The gas control valve is defective Regulate the reducing valve Unblock the nozzle Replace the gas control valve It has a light back sound when turning off the valve N
10. m scale division 0 1 mbar or a digital gauge Procedure as follows Remove the panel unscrew the screw on the pressure port picture 2 Place the pressure gauge Start up the appliance by following the instructions in the user s manual Check supply pressure After the check remove the pressure gauge Replace the sealing screw Sealing screw Picture 2 Pressure port 4 3 Special Notice 10 11 12 13 14 15 The appliance in only designed for food cooking not applicable to other uses The user s manual includes all necessary information about installation operation and maintenance Please operate according to the specific instructions in the manual making sure the appliance works in perfect performance Executive Standard The appliance complies with the criteria in CJ T28 2003 lt Chinese Cooking Gas Appliance gt The appliance is certificated in quality and safety whose code is XK21 007 00951 The warranty remains valid only when the appliance is installed in accordance with precautions and local provisions involved The manufacturer is not liable for loss caused by not observing these precautions Installation initial use and maintenance should be done by professional or licensed personnel or franchised person approved by manufacturer During installation and maintenance to ensure safety of operation please carefully observe the following procedures Keep the user s manual carefully for furth
11. ozzle diameter does not match with the gas supply The damper is too large The supply pressure is too low Flow of connected pipe is not enough PON gt Regulate the nozzle diameter Adjust the damper Regulate the reducing valve Increase the permitted flow It has red flame and black smoke Nozzle diameter does not match with the gas supply The damper is too small Gas nearly runs out Gas ingredients are volatile in gas peak period PP n Regulate the nozzle diameter Adjust the damper Replace the gas Decrease the gas Increase it after the peak flow Aforementioned troubles are just for reference If any failure occurs please stop using and inform the professional technicians to check and repair Safety is first and maintenance should be done after shutting down the power supply and gas supply
12. ty for fire accidents caused by improper operation or maintenance Contents Functional Introduction u4240sn sen eee tent eee eee 1 Structure Schematic Diagram ccceeceeeeeeeeeeeeeeees 1 Basic Features ParametersS cccceeeee cee eeeeee ees 4 Precautions Recommendations 0cceeeeeeeeees 6 Working Instructions amp Operation FIOW 0cceeeee ee 9 Routine ASPE area 11 Cleaning Maintenance ccccceceece eee sense nennen 11 Failure Analysis amp Trouble Shooting 12 1 Functional Introduction This product is manufactured by our company which is combined with advantage from home and abroad It is novel in design reasonable in structure easy in operation all stainless steel made durable in using and convenient in maintenance It is equipped with flame failure safety protection device Also the thermostatic control makes the temperature freely adjustable at a certain range according to food requirement Therefore it is the ideal equipment for hotel supermarket restaurant western restaurant fast food restaurant and food industry 2 Structure Schematic Diagram C9IGRA4GVE1 DEIN VTN m M RARA INEA li a N C9GRA6GVE1 C9IGRA4E1 3 Basic Features amp Parameters 3 1 Basic Model
Download Pdf Manuals
Related Search