Home

AquaClean Manual

image

Contents

1. Robotic Pool Cleaner O Nettoyeur de Piscine O Automatischer Schwimmbeckenreiniger Robot di Pulizia per Piscine Limpiafondos de Piscina Q Aspirador Autom tico de Piscina English O Operating Instructions and Parts List A Mise en marche de votre robot Fran ais nettoyeur de piscine Bedienungsanleitung f r den Deutsch 17 automatischen Bodensauger Italiano 25 Funzionamento del nuovo robot di pulizia per piscine Espa ol G3 Manejo de Limpiafondos de Piscina A Manual de instru es Portugu s g BK 0002700 Dear Customer Thank you for choosing our product to clean your pool We hope that you will enjoy using your new robot to maintain your swimming pool for years to come Before you begin to use your robot please take a few minutes to carefully read these operating instructions Again thank you for choosing our product Handle Handle Lock Mechanism Scrubbing Drive Track Side Plate Brush IMPORTANT CAUTION Do not switch the pool cleaner ON if it is not fully immersed in water Operating the cleaner out of water will cause severe damage immediately and will result in loss of warranty Allow the cleaner to remain in the pool for 15 to 20 minutes following the end of its cleaning cycle This will allow the motors to cool adequately Do not leave the cleaner in the pool all the time Always remember to turn the power supply OFF and unplug it from the power outlet before rem
2. exactly the key and the slots from cable plug with the corresponding key and slots from the transformer socket Fig D 3 Push the plug into the socket of the transformer all the way in 4 Once the plug is in rotate the plug to the right to lock it into place Fig E 5 To remove the plug first rotate the plug to the left to unlock it then pull it out Fig F a Light indicates that the machine is running b Green push button turns the machine ON c Red push button turns the machine OFF IMPORTANT After every cycle the pool cleaner will turn off automatically In case you want to turn the machine off during the working cycle push the red button once and the indicator light will turn off indicating that the machine has stopped running Maintenance and adjustment CLEAN THE FILTER BAG AFTER EVERY CLEANING CYCLE a Unplug the power supply Please keep the plug away from contact with water b If the unit is in the pool gently pull the cleaner toward you using the cable until the handle is within reach Use the handle not the cable to pull the cleaner out of the pool after allowing most of the water to drain from the unit c Lay the unit on its back on a smooth surface in order to prevent scratches on the machine body release the lock tabs and remove the bottom lid assembly fig 4a 4b 4c 4d d Remove the filter bag from the support bars turn it inside out and wash off all the dirt with a garden hose or
3. in a sink Squeeze the bag gently until the rinse water is clear If necessary machine wash the bag using only cold water with NO DETERGENT fig 5 e Re install the bag on the support bars with the label in the center of one of the long sides of the bottom lid 5a f Re install the bottom lid assembly in the body Push down on it until lock tabs will snap into place properly IMPORTANT TIPS Shut off and unplug the power supply every time you remove the cleaner from the water Clean the filter bag after every cycle Reverse the handle after every cleaning cycle to avoid tangling the cable Periodically straighten outthe floating cable Replace worn brushes to ensure maximum cleaning performance Make sure that your pool cleaner positions itself properly on the wall The machine handle must rest parallel to the water line upon reaching the surface ofthe water Save your cleaner s packaging for off season storage or for shipping the unit to your dealer if service is required Leave your pool cleaner in the water for 15 to 20 minutes after every cleaning cycle Do not leave your cleaner in direct sunlight when notin use Never leave the power supply in direct sunlight and avoid leaving it in the rain Occasionally you should rinse your cleaner in clean fresh water This will lengthen the service life of the drive belts drive tracks and scrubbing brushes Clean the propeller once amont
4. necessary b Check if drive belts 6 have slipped out of place Also 3 Unit does not move but does pump water check for proper tension of drive belts 6 If necessary replace belts c Check for loose drive motor 3 connections d Ifa b and c are negative check the Master and Slave motors If one or the other is not functioning send the unit to your service center a Check 2a and 2b of this guide b Check the Intake Valve Flaps 23 on the underside of your 4 Unit does not pick up dirt and debris unit The Flaps should move freely to open and close P Clean and free the Valve Flaps 23 if necessary a Most likely a thorough cleaning of the filter bag 12 is needed b Check to see that the blue cable 15 is properly spread out and is untangled c Allow the unit to run in the pool for the entire cleaning cycle 5 Unit does not seem to cover the entire pool d Make sure that the Floating Handle 14 is locked diagonally across the top of your unit s body e Check that the Pump Motor 2 is operating Please refer to the Troubleshooting section titled Moves But Does Not Pick Up Dirt And Debris f After following all of the above if there is still a problem call your dealer for specific additional assistance Troubleshooting Guide 6 Remote control optional does not operate properly a Check the battery in the Remote Control Transmitter 25 replace if necessary b M
5. ake sure that you activate the RC System 25 no more than 30 meters away from the Transformer pointing the control box to the antenna c If there is still a problem with the RC System 25 call your service center for assistance 7 Debris Comes Out Of The Aquabot When Removing It From Pool Bottom Lid Does Not Close Properly a Lock Tab 24 s Check that the Lock Tabs 24 are not warped They should be straight and aligned with the unit s body b Intake Valves 23 Check that the Intake Valve Flaps on the underside of your unit in the Bottom Lid move freely to open and close Clean Flaps if necessary 8 The cable is twisted a Reverse the diagonal position of the handle b Use the E Z swivel as shown bellow Place the Robot on the ground and unplug the cable from the transformer With one hand holding the E Z Swivel walk away from the Robot pulling the cable to its full length The core will rotate inside the cover and in this way will untangle the cable CABLE CARE The cable may become twisted after a period of time in use To correct this condition simply lock the moveable handle on the top of the cleaner in the opposite diagonal direction The pool cleaner will now travel in the opposite direction while cleaning your pool and the cable will uncoil Check the cable periodically for external damage If the problem persists use the E Z Swivel device Handle Cover Core Cable As
6. ce the unit in the water Turn the unit side to side in the water to allow air to escape from the body and then let the cleaner sink to the bottom of the pool fig 3 Then spread the cable over the surface of the pool as evenly as possible fig 1 O Plug the cable into the power supply Make sure the key on the plug exactly corresponds with the key slot on the socket of the power supply fig 1b Plug the power supply into a grounded outlet Ensure that the electric outlet has been properly grounded fig 1c The light will glow indicating that the system is ON and the pool cleaner will start the cleaning cycle The unit keeps record of the number of cleaning cycles Only an authorized service center can display the accumulated cleaning cycles See details on the next page WARNING A Ground Fault Current Interrupter GFCI USA or a Residual Current Device RCD EUROPE must be installed to protect your electric outlet and prevent any possible electric shock Power Supply Operating Instructions slot slot Socket key key Cable Transformer plug socket Rotate left and pull to unlock To plug the cable Fig A into the socket on the power supply Fig B please do the following 1 Prepare the plug as seen in Fig C with the key and 3 outside slots exactly as shown 2 Fit
7. h see next page for details Wheel tube CHANGING BRUSHES Depending upon how frequently you use the cleaner pool cleaner it will be necessary to replace the brushes when they are worn out Worn out brushes will impede cleaner s scrubbing climbing the walls or general performance a Detach one of the side plates unscrewing the four screws see fig 7a b With side plate detached take out the wheel tube from the machine c Open the end hub and pull out the worn PVA brush see fig 6 d Place the new PVA brush on to the hexagonal tube and close it with the end hub e Reinstall the wheel tube in place and place back the side plate screwing back the four screws Drive Track PVA BRUSHES CARE This special brush material is most efficient when wet Any discoloration is normal in the drying process when exposed to open air Please allow brushes to absorb pool water for about 20 minutes before initial use or at first use of every season You will notice that as the brushes absorb the water and start scrubbing your pool the discoloration will disappear CHANGING THE DRIVE BELTS Depending on usage the drive belts located behind the side plate will stretch When this happens in order to maintain the optimum performance of the unit these drive belts have to be changed a Turn the robot upside down and remove the bottom lid assembly fig 4a 4b 4c 4d b Inside locate 4
8. oving the cleaner from the pool WARNING Your Cleaner should not be used while people are swimming in the pool Safety Note The unit must be supplied through a residual current device RCD having a rated residual operating current not exceeding 30 mA The connection to the branch circuit should be consistent with the local and national wiring rules electrical code Mishandling of the unit can result in leakage of lubricants If the supply cord is damaged it must be replaced by the manufacturer s service agent or a qualified and trained person in order to avoid hazards Operating the Pool Cleaner Your new automatic pool cleaner contains The robotic pool cleaner with its floating cable The Power Supply transformer Cart optional Please read this manual completely before operating your pool cleaner O Place the power supply transformer at least three meters ten feet from the pool fig 1 The transformer will supply low voltage to the cleaner O Uncoil the cable fig 1a O For proper operation lock the moveable handle diagonally across the top of the cleaner s body Push down on the handle lock mechanism and slide the handle all the way to the end recommended one slot before the end then release the lock The handle will remain fixed in this position Repeat this process on the other side of the cleaner Remember the handle must be fixed diagonally fig 2a 2b O Pla
9. screws on drive motor side which hold the side plate in place fig 7a 7b c Take out these screws and remove the side plate d Remove the drive track Before removing the drive track notice carefully how the drive belts are positioned for re assembly fig 7c e Take out the old drive belts and replace them with new ones To re assemble reverse steps d to a Cleaning the pump propeller 1 Take out the 2 4 screws from the outlet top 2 Take out the outlet top and remove hair and other debris around propeller CAUTION To avoid scratches and other blemishes appearing on your robot simply find a smooth surface for it to rest on when cleaning the debris bag or performing minor adjustments These scratches could produce changes in the robots soft and smooth edges resulting in potential damage to some flexible pool surfaces smooth surface Troubleshooting Guide PLEASE CHECK THE FOLLOWING BEFORE CALLING YOUR SERVICE CENTER Before troubleshooting the pool cleaner must be disconnected from the power supply and the power supply must be unplugged from the electrical outlet to prevent damage to the unit and possible personal injury For reference numbers consult the parts list diagram located on the last page of the instructions a Check to see if electric outlet 22 has power b Check if tran
10. sformer 16 is plugged into a grounded outlet and the blue cable assembly is plugged into the transformer c Switch the power supply OFF 19 and ON 21 buttons 1 Unit does not pump water or move a few times Allow 45 seconds between ON and OFF d Check for and remove any debris such as hair string or leaves that may be obstructing the free movement of the Drive Pulley 5 Drive Belts 6 or Drive Tracks 7 e Check that the Drive Belts 6 and Drive Tracks 7 are properly aligned and are taut Adjust or replace if necessary a Check to see if propeller 1 is seized due to accumulation of hair or debris on the propellers Remove the top screws on each outlet top 1 and clean the propeller When 2 Unit does not pump water at all or pumps slowly reassembling the top cover do not overtighten the screws but moves b Check to see if the filter bag 12 is thoroughly clean Clean as necessary c If a and b are negative check the pump motors 2 If they are not functioning send the unit to your service center The transformer cord can only be replaced with the aid of special purpose tools normally available only to authorized dealers distributors and service centers Troubleshooting Guide a Check to see if forward reverse motion is obstructed by foreign matter hair debris etc on drive belts 6 or drive tracks 7 or there is an entanglement with the power cord Clean as
11. sy patent pending

Download Pdf Manuals

image

Related Search

Related Contents

Samsung PL PL120  平成27年度東大阪市環境物品等調達基準 (サイズ:3.23MB)  Philips AJ4200/12 User's Manual  KR-747 - Krämer Automotive  Defort DMS-1200  Dell PowerEdge R820 Manual del propietario  FORZADA: - Termicol  

Copyright © All rights reserved.
Failed to retrieve file