DRD8 v2 (Installation Instructions)
Contents
1. Tap once Fade the load to its last used level switch ON Tap twice Full bright switch ON 4 Increase the present level switch Fade to 0 switch OFF b Pressandhold Decrease the present level switch OFF When you When you see 4 in the see JL the instructions instructions touch the top touch the of the switch bottom of as directed the switch as directed 9 Power Fail Memory After a power failure all Miro devices automatically return to the state that they were in immediately prior to loss of power CLEANING Clean using a cloth dampened only with water and a little mild detergent Use of solvents or hydrocarbon based cleaners may cause permanent damage TROUBLESHOOTING During house ID binding the LED is not flashing on some wireless devices If LED is solid green before initiating house ID binding The device already has another house ID Reset it to the factory default so that it can be bound to the desired house ID Resetting to factory defaults is described in the I need to start over issue If LED is solid yellow after initiating house ID binding The device may be out of range of the initiating device Add a MRR2G Wireless Repeater to boost signal range During Group binding all LEDs stop flashing before get back to the device to press The 5 minute group binding process2. MarCom Engineering Title DRD8 v2 Installation Instructions QA Orig Drawing Date 16 MAR 07 Revision Date 24 SEP 07 Drawing TITLE BOX PG Scale 1 1
3. timer may have expired Restart the binding process timer by repeating steps 1 and 2 of the procedure you were using Notice that the devices you previously included are flashing yellow simply finish the process from where you left off The device LED flashes red when press If house or room scene controllers are used in the house the house room configuration may be locked Consult the installation instructions for the DRDS or MRH5G wireless house scene controller if one is present See the DRD6 or MRH6G wireless room scene controller instructions if one is present made a configuration mistake need to start over To reset any Miro wireless device to factory default settings press and hold 4 until the LED changes to solid yellow approximately 10 seconds During the process the LED flashes yellow When complete it becomes solid yellow The device can then be reconfigured exactly like any new device FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occ
4. to terminate Group binding All LEDs revert to solid green Now all the devices in the Group control their load circuit in exactly the same manner If some devices flash yellow a Group has already been set up that includes those devices Adding a Device to a Group in an Existing System 1 Go to a device that is in the Group where you want to add the device Press until the device LED and all members of the Group flash yellow about 2 seconds The new device flashes green Press 5 on the new device until its LED flashes yellow about 2 seconds Return to the device used in step 1 and press All LEDs are solid green REV DESCRIPTION INT REV DATE APPROVED 1 ECO 01933 MJS 3 28 07 2 02411 MJS TITLE BOX PAGE ONLY DO NOT MAKE FILM DO NOT PRINT Print 2 sides e Ink Color Black 9 e Paper White 16 609 sq uncoated prefer recycled stock e Final trim size 16 Wide x 6 High e Four 4 fold e Final folded size 4 Wide x 6 High IF YOU HAVE ANY QUESTIONS REGARDING SPECIFICATIONS OR REQUIRE ADDITIONAL FILE FORMATTING PLEASE CONTACT Mary Jo Sowinski Phone 408 486 7511 Email maryjo sowinski Legrand com All information in this drawing is the property of Watt Stopper Legrand and cannot be copied or used without the written approval of Watt Stopper Legrand Drawn by SOWINSKI SD WattStopper tiegrand SANTA CLARA CALIFORNIA PLM
5. 2 seconds Verify that the newly added device LED is flashing green indicating that it has acquired the House ID Return to the same previously bound device used in step 1 and press until the LED changes to solid green about 2 seconds All device LEDs should now be solid green Groups Binding a Miro wireless device together in the same group with one or more DRD8 controllers allows you to control the same device from multiple locations Devices that are bound in the same Group work in exactly the same way from any of the control locations You can include a variety of Miro wireless devices in the Group Just remember that all devices in the Group operate when one member operates For example if you increase the brightness of one device in the Group all devices will increase brightness switching devices turn ON Set the House ID see Set House ID before setting up Groups Set up a New Group 1 Go to any device that you want to include the Group Press The device LED flashes yellow and all other devices in the House flash green You now have 5 minutes to complete this process To include or exclude a device in the Group press on the device until the LED changes color Yellow flashing LED Included in the Group Green flashing LED NOT included in the Group If you get to a device and it is NOT flashing see TROUBLESHOOTING Return to the device used in step 1 and press
6. Miro wireless devices Application support information and the Miro Installation Guide is available on line INSTALL IN COMPLIANCE WITH ALL APPLICABLE CODES amp STANDARDS Failure to follow these instructions may cause personal injury or equipment damage CAUTION A TURN THE POWER OFF AT THE CIRCUIT BREAKER BEFORE INSTALLING THE CONTROLLER INSTALLATION For ease of installation manufacturer recommends use of a deep wall box The device is equipped with flying leads to simplify installation however if desired they may be removed by loosening the screw terminals 1 Disconnect power to circuit by turning circuit breaker OFF before installation 2 Remove existing wall plate and switch 3 Strip existing wires 1 2 If two wires will be connected to the same terminal Miro device both wires must be the same gauge 12AWG or 14AWG 4 Wire the LINE black NEUTRAL white and GND green or bare supply wires to the correspondingly marked terminals according to the wiring diagram below 5 Attach the wall plate 6 Switch the circuit breaker ON 7 Make sure the LED on the DRD8 controller is lit It should be yellow if not see TROUBLESHOOTING SUPPLY WIRES SET HOUSE ID All Miro wireless devices installed in the same home must acquire the same unique House ID before use This process is known as house binding Each Miro wireless device
7. is bound to all other Miro wireless devices in the house New Installation 1 With all devices installed and energized make sure that every Miro wireless device LED is yellow If any LED is off be sure the circuit breaker is on and the device is correctly installed Press 3 on any device paddle until When you see the LED flashes yellow about 2 in the instructions seconds This indicates that it has firmly press and acquired a unique House ID hold both the top and bottom of the Make sure that all other Miro devi ddl il ireless device LEDs are flashin Cice pare unt ind that they 9 the LED changes green indicating that they have Ce jJ labout 2 seconds acquired the same House ID Return to the device used in step 2 which is still flashing yellow Press until the LED changes to solid green about 2 seconds device LEDs in the House change to solid green indicating house binding is complete Adding a Device to an Existing Installation If you re adding or replacing a device a Miro wireless installation that is already operating the new device must be bound to the same House ID as the other Miro wireless devices in the house After the new device is powered up the LED should be solid yellow This indicates that it has not yet acquired a House ID To acquire the House ID for the existing system 1 Press any previously bound device until the LED flashes yellow about
8. ocation Controller Specifications Voltage 120 277VAC 60Hz Operating 32 F to 104 F 0 C to 40 C Patents pending legrand W VANTAGE UNIT DESCRIPTION The Miro Decorator DRD8 Wireless Multilocation Controller is used together with Miro Decorator wireless devices to control lighting or appliance loads from multiple locations The DRD8 can be used in a group with the following Miro Decorator devices DRD2 Wireless Incandescent Dimmer DRD3 Wireless Switch DRD4 Wireless Universal Dimmer DRD9 Wireless Fan Control MRP W_ Wireless Plug In Lamp Module MRP7W Wireless Plug In Appliance Module Load Types The DRD8 has no direct connection to the load See the installation instructions or specifications for the device connected to the load to determine compatibility with those devices Miro Wireless Miro wireless devices use radio signals to communicate with each other to control lighting and other types of electric loads in selected areas They use the 900MHz band for high speed control communication Using the patented frequency agile Dog technology Miro wireless devices avoid interference with other 900MHz devices such as cordless phones and baby monitors Application Assistance The Miro Installation Guide provides more information about configuring scenes and presets Instructions for installation and use are included with the relevant
9. ur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment in an outlet a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Caution Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment WARRANTY INFORMATION Manufacturer warranties its products to be free of defects in materials and workmanship for a period of five 5 years There are no obligations or liabilities on the part of manufacturer for consequential damages arising out of or in connection with the use or performance of this product or other indirect damages with respect to loss of property revenue or profit or cost of removal installation or reinstallation Legrand Customers contact Vantage Customers contact legrand Wvantace Please Recycle 301 Fulling Mill Road Suite G 1061 South 800 East Middletown PA 17057 Wy Orem UT 84097 Phone 800 321 2343 29 Phone 800 555 9891 www legrand us onq 15 0515 www vantagecontrols com DRD8 v2 Wireless Multil
Download Pdf Manuals
Related Search