User Manual
Contents
1. THE END OF ITS SERVICE LIFE This appliance is marked with the waste sorting symbol concerning scrap electrical and electronic equipment This means that the product must be disposed of via a selective waste sorting system in accordance with directive 2002 96 CE DEEE Professional Appliances section so that it can be either recycled or dismantled in order to reduce any impact on the environment For further information you can contact your dealer or SANTOS For the disposal or recycling of the appliance components please refer to a specialist company or contact SANTOS Electronic items that have not been through the selective waste sorting system present a potential danger for the environment The packaging material should be disposed of or recycled in accordance with regulations in force 98127 EN 2 2 12 2010 MA Www santos fr DESCRIPTION OF THE APPLIANCE The beater mixer can be used to beat mix and whisk preparations made by professionals in restaurants pizza houses snack bars catering outlets sandwich bars special theme restaurants etc The appliance consists of an aluminium body and stainless steel plating Thanks to the asynchronous motor it can operate with a hook paddle or a whisk delivered as standard with the appliance The working part of the hook and whisk is made of stainless steel while the working part of the paddle is made of food quality aluminium 3 types of tools e Hook 5 for pro2. any intervention on it cleaning general care maintenance 7 Use of spare parts other than certified original SANTOS parts is prohibited oR D O ELECTRICAL CONNECTION e The electric power supply for the appliance is available in 2 single phase voltages and a three phase version 110 120 V 50 60 Hz 220 240 V 50 60 Hz 220V and 380V 50Hz three phase 98127 EN 2 2 12 2010 LL www santos fr Line protection the appliance must be connected to a standard socket 2 poles ground for the single phase versions The set up must be fitted with a differential circuit breaker and a 16A fuse The earthing of the appliance is compulsory TAKE CARE eBefore connecting the machine check that the mains electrical voltage is the same as the voltage for your appliance Its value is shown gt either on the identification plate under the machine gt or on the identification plate on the last page of this manual elf the power cable 8 is damaged it should be replaced by a special assembly available from approved SANTOS dealers or from SANTOS USING FOR THE 1st TIME Pull the lever 1 forwards to unlock and lower the bowl 2 Remove the bowl support 3 bowl 2 and accessories in their wrappings Remove unwrap and wash the three tools in clean water Wash all the elements in contact with food in clean water the bowl 2 the inside part of the bowl centering device 4 ROM RECYCLING THE PRODUCT AT
3. weight Height mm 585 Width mm 340 Depth mm 570 Net weight kg 30 Packaged weight kg 34 Bowl Volume I 9 9 Useful volume l 8 1 These ratings are given for your guidance The exact electrical specifications of your appliance can be found on the rating plate 2 Noise level measured in terms of acoustic pressure with the machine loaded according to standards ISO 11201 1995 and ISO 4871 1996 Appliance placed on a work surface 75cm above the ground Microphone turned towards the appliance at 1 6m from the ground and 1m from the appliance 98127 EN 2 2 12 2010 Mb Www santos fr Electrical diagrams 110 120V 50 60Hz wiring diagram Black Blue White Starter relay On Off FEJ Ro A po Brown Ps Switch bowl Brown E Switch Grid Stop Brown Q Green yellow 15 and 16 il 98127 EN 2 2 12 2010 MA www santos fr 380V 220V 50Hz three phase wiring diagram Black Brown Q gt e Red oir Yellow Switch bowl Orange fore C Brown 220V three gt phase OO O Switch Grid MOTOR connection k Q y AE O White P White J On Off Green yellow 1415 and 16 i 98127 EN 2 2 12 2010 MA Www santos fr 220 240V 50 60Hz wiring diagram Black Brown White White 2 en O sand White 5 4 3 a WW j Starter relay 4 AT 3 vy On off E se Switch bowl Switch grid Stop Brown A F Brown B Q Green yellow
4. Off lamp 13 lights up when the switch is at position 1 On Call in a specialist technician to check the appliance s electrical components The appliance stops after the motor has overheated the metal casing around the speed change lever is hot Press the mushroom head switch 14 disconnect the appliance from the mains socket and follow the instructions in the motor overheating safety feature section The appliance stops following an overload If the motor stalls during operation see the motor overload safety feature section The tool no longer rotates and the lamp on the switch 13 is lit e press the mushroom head switch 14 disconnect the appliance from the mains socket and check the condition of the belt 20 see the Maintenance belt change section 98127 EN 2 2 12 2010 MA www santos fr APPLIANCE TECHNICAL SPECIFICATIONS Mains Power supply voltage ld 320 V 220 240 110 120 220 240 Three Three phase phase Frequency Hz 50 60 60 50 50 Start capacitor uF 150 190V 250 130V 150 190V Motor Rating kW 0 6 0 65 0 65 0 51 0 51 Motor speed rpm 1500 1800 1800 1500 1500 Number of speeds Min planetary speed 50 60 60 50 50 rpm Max igs y speed 459 180 180 150 150 Min tool speed rpm 180 210 210 180 180 Max tool speed rpm 540 640 640 540 540 Noise 2 Loa ne Kai 2 50B 65 65 65 65 a Dimensions and
5. SANTOS SAS 140 150 AVENUE ROGER SALENGRO 69120 VAULX EN VELIN LYON FRANCE o T L 33 0 472 37 35 29 FAX 33 0 478 26 58 21 SANTOS E Mail santos santos fr www santos fr PLANETARY MIXER 27 USER AND MAINTENANCE MANUAL IMPORTANT documents included in this manual to be kept e CE COMPLIANCE DECLARATION e WARRANTY CERTIFICATE Read the user instructions before unpacking the appliance Coffee grinders Fruit juicers Mixers Blenders Drinks dispensers Planetary mixers Cheese graters Ice crushers Grinders Vegetable slicers Dough mixer Moulins a caf Presse fruits Mixers Blenders Distributeurs de boissons Batteurs m langeurs P trin Rapes a fromage Broyeurs a glagons Hache viande Coupe l gumes MODELES DEPOSES FRANCE ET INTERNATIONAL INTERNATIONALLY PATENTED MODELS 98127 EN 2 2 12 2010 MA www santos fr CONTENTS CE COMPLIANCE DECLARATION cia AAA AAA 3 SAFETY INSTRUCTIONS comido 4 INSTALLATION AND HANDLING isc A AA 4 IMPORTANT RESTRICTIONS aimara 4 ELECTRICAL CONNECTION isa id 4 USING FOR THE TSt TIME ain a a ia 5 RECYCLING THE PRODUCT AT THE END OF ITS SERVICE LIFE 5 DESCRIPTION OF THE APPLIANCE uen 6 USING THE APPLIANCE satin pooR 6 STARTING WORK eoa D a D Ode 6 CHANGING THE TOO eseina aaea O e ei 8 CLEANING AAA A AA eme 8 SAFETY MAINTENANCE za aca 9 DAPETY DEVICES sacan O a D A 9 Bowl presence safety device usas 9 Mot
6. ducts that are difficult to process such as bread dough pizza doughs pastry doughs etc e Paddle 6 for products that need to be mixed and made homogeneous such as pancake batter waffle batter cake mix choux pastry dough kneading of meat and fish preparations purees various mixes etc e Whisk 7 for light products that need to be mixed and made homogeneous such as sponge batters meringues butter creams mayonnaise whisked egg whites various light mixtures etc Bowl made of stainless steel capacity 9 9 liters useful capacity 8 liters e g for pancake batters USING THE APPLIANCE STARTING WORK 1 After selecting the appropriate tool for the work to be done hook 5 paddle 6 or whisk 7 you can a either fit the tool to the rotating shaft by locking the bayonet system in place then install the bowl 2 with or without the products to be processed in it on the bowl support 3 b or install the bowl 2 with or without the products to be processed in it on the bowl support 3 then fit the tool to the rotating shaft by locking the bayonet system in place 2 Push the handle 1 backwards to raise the bowl 2 3 When the handle 1 reaches its end of travel the bowl 2 is locked in position 4 Connect the supply cord plug 8 to your mains supply socket 5 Put the products to be processed in the bowl 2 if this hasn t already been done To do this the safety grid 9 has to be lifted 6 Select
7. i 98127 EN 2 2 12 2010 MA Www santos fr item F 1 Locking lever 2 Bowl 3 Bowl support 4 Bowl centering device 5 Hook tool 6 7 8 9 Paddle tool Whisk tool Mains power cable Grid 10 Speed control lever 11 Rack 12 Column 13 On Off switch 14 Mushroom heaa switch 15 Motor 16 Tool shaft 17 Cover fixing screw 18 Cover 19 Capacitor 20 Belt 21 Variable speed pulley 22 Drive pulley 23 Rack fixing screw 24 Base 98127 EN 2 2 12 2010 By www santos fr www santos fr 98127 EN 2 2 12 2010 SS santos J WARRANTY CERTIFICATE WARRANTY Since the 01 01 95 all our appliances comply with CE and possess the CE label Our guarantee is of 24 months from the manufacturing date mentioned on the descriptive plate except concerning the asynchronous motors consisting of a rotor and a stator which are warranted for 5 years from their manufacturing date Warranty is strictly limited to the free replacement of any part of origin recognized by us as defective due to a defect or building default and identified as belonging to the concerned appliance Warranty does not apply to damages resulting from installation or use non complying with our appliance data sheet users manual or in case of an evident lack of maintenance or disrespect of elementary security electric rules It doe
8. ing the warranty period the Distributor has to unless a different written agreement of SANTOS indicate to his customer to stop any use of the defective product Such a use would release SANTOS of any responsibility APPLIANCE IDENTIFICATION PLATE SPECIMEN For all documents not delivered with the appliance l Printed Faxed Downloaded 98127 EN 2 2 12 2010 MA www santos fr
9. ins 2 Unscrew the locking screw 17 and remove the cover 18 3 Discharge the starter capacitor 19 4 Lift the belt 20 to disengage it from the driven pulley 21 turn the pulley by hand to make it easier to remove the belt 5 Disengage the belt 20 from the drive pulley 22 and remove the belt from the beater mixer Fitting the new variable speed drive belt 1 Fit the new belt 20 on the drive pulley 22 2 Lift the belt 20 to fit it on the driven pulley 21 turn the pulley by hand to make it easier to engage the belt 98127 EN 2 2 12 2010 MA Www santos fr 3 After installing the belt 20 turn the driven pulley 21 by hand and gradually pull the speed control lever 10 until it reaches the high speed position 4 Once in this position check the distance for the top of the belt at the outer diameter of the drive pulley 21 minimum distance 39 mm maximum 40 mm see the sketch Min 39 mm Max 40 mm e lf the distance measured is correct then the belt 20 change operations are finished All that is needed is to carry out the following operations Replace the cover 18 and screw the locking screw home 17 Connect the appliance to the mains electricity supply and start the beater mixer then change the speed a few times to check that the variable speed drive operates correctly over the whole range of speeds e lf the distance measured is outside the tolerances the rack 11 for the speed contr
10. ng the machine by raising the safety grid 9 To start the appliance up again the safety grid 9 must be lowered TAKE CARE Scattering of flour dust when loading or starting the appliance is dangerous for health It is recommended to fill the bowl gradually at an even rate and even to use a protective mask in reduce any inhalation of flour dust to a minimum 98127 EN 2 2 12 2010 BA www santos fr CHANGING THE TOOL All tool changes must be carried out with the appliance halted and the bowl support in the lowered position FITTNG 1 Place the tool on the rotating shaft 16 2 Push the tool upwards 3 Turn and lift the tool slightly anticlockwise in order to engage the pin bayonet on the tool rotation shaft 16 REMOVING 1 Do the same operations as for fitting in reverse CLEANING IMPORTANT e Stop the appliance and unplug its power cable from the mains e Cleaning with a jet of water or by pressure is not allowed It is recommended to clean the appliance as soon as you have finished using it It will be easier to clean if you do not allow the remaining scraps of food to dry e Clean the tool hook paddle or whisk after use with water or a detergent made for dish washing Then rinse and dry e Clean the stainless steel bowl after use with water or a detergent made for dish washing Do not use abrasive products or pads to clean the bowl e Clean those parts of the frame in contact with the food using water o
11. ol level 10 must be adjusted as follows 1 Loosen the two screws 23 fixing the rack 11 and move the rack forwards if the distance measured is less than 39 mm or backwards if the distance exceeds 40 mm Turn the driven pulley 21 by hand and check the belt position measurement Continue in this manner until a suitable measurement is obtained then screw home the two screws 23 fixing the rack in position 11 4 Move the speed control lever 10 to the low speed position and turn the driven pulley 21 by hand to check the position of the belt in the pulley the belt must never protrude beyond the outer diameter of the pulley Replace the cover 18 and screw the locking screw home 17 Connect the appliance to the mains electricity supply and start the beater mixer then change the speed a few times to check that the variable speed drive operates correctly over the whole range of speeds N oo 98127 EN 2 2 12 2010 MA Www santos fr FAULT FINDING Identifying the cause of appliance stoppage with precision If the problem persists switch off the power supply to the appliance unplug the cable from the mains socket and call in the maintenance service or contact a SANTOS approved dealer The appliance will not start e Check that the grid is in the low position and that the bowl is locked in the up position Check the mains supply the condition of the supply cord and plug Check that the On
12. or overload safety feature 9 Motor overheating safety feature irarenaaaraaaana 9 Tookaccess safety TEAL anuario 9 WMAINTENANO Esa aio 10 o NN Ne dl dd Dadas d dana EE 10 Changing a worn belt on the variable speed drive replacement after breaking 10 Fitting the new variable speed drive belt o oooccccccnnncccccccccccccccnnnnanancccnnnncnonananananonons 10 FAULTFINDING gs 12 The appliance will not SN casas cassio sis ti meme 12 The appliance stops after the motor has overheated 12 The appliance stops following an overload aa 12 The tool no longer rotates and the lamp on the switch 13 is lit 12 APPLIANCE TECHNICAL SPECIFICATIONS 13 Electrical digrais sara prada on nn a OS a 14 110 120V 50 60Hz Wiring diagram ss 14 380V 220V 50Hz three phase wiring diagram a 15 220 240V 50 60Hz wiring diagram eee e reece eeeeeeeeeeeeeeeeeeeeeeeeaeeeeeeeeeeeeeee 16 EOS PR Porcina E A A EO A TORA aa cod 18 WARRANTY CERTIFICATE osorno nono nono 19 APPLIANCE IDENTIFICATION PLATE idees 19 98127 EN 2 2 12 2010 Lh www santos fr CE COMPLIANCE DECLARATION THE MANUFACTURER SANTOS sas 140 150 Av Roger SALENGRO 69120 VAULX EN VELIN LYON FRANCE declares that the appliance intended for the professional market described below Description PLANETARY MIXER Type number 27 complies with e the statutory provi
13. r a detergent made for that purpose Then rinse and dry e The base 24 is to be cleaned with a soft damp sponge then dried 98127 EN 2 2 12 2010 Lh www santos fr SAFETY MAINTENANCE SAFETY DEVICES If the problem persists switch off the power supply to the machine unplug the cord from the mains socket 8 and call in the maintenance service or contact a SANTOS approved dealer Bowl presence safety device The bowl 2 must be centered and held firmly in the upper position between the bowl support 3 and the machine frame 4 before the appliance is allowed to work The bowl must be present to allow the appliance to be started When the bowl 2 is unlocked this stops the appliance Acutin the mains power supply results in the On Off switch 13 stopping position 0 Re starting the beater mixer requires specific operation of the On Off switch 13 again position 1 oR WP Motor overload safety feature Should the motor 15 become blocked foreign body object that is too hard the On Off switch 13 automatically trips to the O position Correct the problem and press the On Off switch 13 position 1 Motor overheating safety feature If the motor overheats the On Off switch 13 automatically trips to the 0 position Wait for the motor to cool 15 to 30 minutes then push the On Off switch 13 position 1 Tool access safety feature The beater mixer can onl
14. rticular requirements for commercial electric kitchen machines Drawn up in VAULX EN VELIN on 01 01 2010 Signatory s position CHIEF EXECUTIVE OFFICER Signatory s name Aur lien FOUQUET A q a e is Signature 98127 EN 2 2 12 2010 VN www santos fr SS santos J SAFETY INSTRUCTIONS When using maintaining or scrapping the appliance take care to comply fully with the following elementary precautions Read the explanatory leaflet in full Note In order to make it easier to understand the following paragraphs please refer to the diagrams given towards the end of the manual INSTALLATION AND HANDLING It is forbidden to pick up the appliance using the levers control handles or protective grid The machine can be handled by a single person For ease of use it is recommended that the machine is placed on a table or work surface to make it easy to add ingredients or to check on progress with processing recommended height 90 cm to be adapted according to the user IMPORTANT RESTRICTIONS 1 The appliance is designed exclusively for beating mixing or whisking foodstuffs The appliance is not designed for processing frozen foods The machine must not be left to operate without supervision Neither a hose nor a pressure hose should be used for cleaning In order to protect against the risk of electrocution do not put the base in water or any other liquid Unplug the appliance before
15. s not apply in case of regular wear and tear Any replacement of parts under warranty will be realized after return of the defective part in our workshops postage paid supported by a copy of a conformity statement on which appears the serial number of the appliance Every appliance is equipped with a descriptive plate conforming to the EC recommendations and of which a duplicate exists in the conformity statement serial number manufacturing date electrical characteristics In case of serious damage judged repairable only in our workshops and after prior consent from our departments any appliance under guarantee is sent by the Distributor carriage paid In case of repairs or reconditioning of appliances not under guarantee the round trip transport is payable by the distributor The parts and workforce are invoiced at the current rate A preliminary estimate can be supplied Coffee grinder not using SANTOS original burrs are not taken under guarantee The warranty conditions repairs reconditioning of the espresso coffee grinder are the object of a specific note Our guarantee does not extend to the payment of penalties the repair of direct or indirect damages and notably to any loss of income resulting from the nonconformity or the defectiveness of products SANTOS s global responsibility being limited to the sale price of the delivered product and to the possible repair of the defective products In case of revelation of an imperfection dur
16. sions defined in appendix 1 of the European machines directive n 2006 42 CE and the national legislation transposing it e the statutory provisions of the following European directives and regulations o N 2006 95 CE low voltage directive N 2004 108 CE EMC directive No 2002 95 CE RoHS directive No 2002 96 CE WEEE directive N 1935 2004 CE regulation relating to materials and articles intended to come into contact with foodstuffs O OOO Harmonised European standards used to give presumption of conformity with the essential requirements of the above mentioned directives e NF EN 454 A1 2010 Food processing machinery beater mixers Safety and hygiene requirements This European standard is a type C standard as defined in EN ISO 12100 When the provisions of this type C standard differ from those stated in the type A or B standards the provisions of the type C standard override the provisions of the other standards This standard provides the means to comply with the requirements of the machines directive n 2006 42 CE see appendix ZA e NF EN ISO 12100 1 and 2 2004 Safety of machinery General principles for design e NF EN 60204 1 2006 Safety of machinery Electrical equipment of machines General requirements e NF EN 1672 2 2005 Food processing machinery Basic concepts Hygiene requirements e NF EN 60335 1 2003 Household and similar electrical appliances Safety e NF EN 60335 2 64 2004 Pa
17. the speed lever 10 position according to the work to be done and the desired speed Put the lever 10 in one of the 8 notches in the rack 11 to the right of the column 12 The first notches towards the front are for high speeds 98127 EN 2 2 12 2010 MA www santos fr whisking those in the middle for medium speeds work with the paddle and the furthermost notches for slow speeds work with the hook 7 The grid must be down and the bowl in the raised position before starting the appliance by putting the on off switch 13 to position 1 the lamp should light up 8 When the preparation is ready stop the machine a either by putting the On Off switch 13 to the O position b or by pressing the red mushroom head switch 14 9 Pull the handle 1 forwards to lower the bowl 2 10 Then either remove the tool from the rotating shaft by unlocking the bayonet system then remove the bowl 2 or remove the bowl 2 then remove the tool from the rotating shaft by unlocking the bayonet system HOW TO STOP THE MACHINE The machine can be stopped in several ways e by using the On Off switch 13 e or by pressing the red mushroom heaa switch 14 e or by raising the safety grid 9 e or by unlocking the bowl 2 ADDING INGREDIENTS DURING PROCESSING You can add further ingredients flour eggs oil etc during processing How to do this e either through the safety grid 9 with the appliance running e or by stoppi
18. y start when the safety grid 9 is in the lowered position When the safety grid 9 is closed there is no access to the tools in the bowl during processing operations The safety grid does however allow products to be added during operation without having to raise it 98127 EN 2 2 12 2010 WN www santos fr MAINTENANCE Prior to carrying out any intervention on the appliance it must be disconnected from the mains without fail Discharging the capacitor Use a screwdriver with insulated handle to touch the 2 connectors on the capacitor 19 The appearance of an electric arc snows that the capacitor has discharged Spare paris IMPORTANT Use of spare paris other than certified original SANTOS parts is prohibited This machine requires no specific maintenance The bearings are lubricated for life If work is required to replace worn parts such as transmission belt tools or the electric or other components refer to the parts list see exploded view at the end of the manual For all spare part orders see references in the exploded view at the end of the manual state gt the type gt the machine serial number and gt the electrical characteristics marked under the machine Changing a worn belt on the variable speed drive replacement after breaking Before proceeding with the variable speed drive belt 20 change it is recommended to stop the beater mixer at slow speed 1 Disconnect the appliance from the ma
Download Pdf Manuals
Related Search