Z-Wave In-Wall Single Switch Manual
Contents
1. 2 Works with MI CASA VERDE VERA DicrtAHIomMe ii SYSTEMS Schlage LiNK LAGOTEK HOME SEER AEON LABS mcControl ADT Pulse Z Wave InWall Single Switch User Guide DHS ZW SWIW 03 Z Wave Technology for Automated Homes Z Wave is a State of the art wireless technology used as a standard for wireless home control It is a next generation wireless ecosystem that lets all your home lighting systems and elec tronics talk to each other and to you via a controller or a gateway It uses simple reliable low power radio waves that easily travel through walls floors and cabinets All products in Australian New Zealand version 921 4h MHz featuring the Z Wave logo are certified to work smoothly with each other Product Overview The DHS In Wall Single Switch DHS ZW SWIW 01 is effective Z Wave switch device specifi cally designed for use in smart homes and offices The product allows to switch on off attached lighting single circuit wirelessly using a Z wave enabled AUS NZ version 921 42 MHz controllers compatible universal remote con trollers control panels gateways PC with Z Wave USB dongle or manually via connected manual switch The switch can act as a wireless repeater to ensure that commands intended for another device in the network are received This is useful to eliminate RF deadspots when the radio range of the Z Wave network is influenced This function is part of the Z Wave network func tionality a2. controller UW Exclusion from Z wave home network general instructions 1 Install Connect the Z Wave In Wall Switch to the load power circuits and to the manual switch as per instructions in the section INSTALLATION above 2 Start exclusion procedure on your controller and when requested press and release the round button on the product s enclosure During the whole procedure the controller and Z Wave In Wall Switch must be close proximity of not more then 15cm 3 Successful exclusion will be indicated by your Z Wave remote controller LED on the Z Wave In Wall Switch will start slow blinking In case exclusion was not successful try the procedure again Association with other Z wave devices e g motion sensor general instructions 1 Include the Z Wave In Wall Switch into your Z Wave home network 2 Start association procedure on your controller and when requested press and release the round button on the device SAFETY INSTRUCTIONS Always read the safety instructions carefully Keep this User s Manual for future reference Keep this equipment away from high humidity and any liquid This product is for indoor use only inside dry wall cavity or similar environment Keep e nough space around for ventilation Do not connect to the load bigger then maximum approved for this product Do not connect to the non compatible load If the product s enclosure is damaged it shall be replaced by the manufacturer or its se
3. nd is set up via Z Wave controller Installation Please check the maximum load before installing or operating Please note in Australia and New Zealand the installation must be done by certified electrician Please note Two state switch will not work properly Button on the wall plate have to be Bell Press type e g push button Saturn Series 60PBBP or similar It is recommended that you wire your Switch Controller and include it into Z Wave network before mounting it in a wall cavity Leigh of wires between manual button and device must be less than 0 5m You may setup your Switch and include into Z Wave grid before mounting in wall cav ity Manual Operations Press and release the button on the connected Bell Switch to switch on turn off the con nected light Once the light is on you can switch ON OFF the light by pressing and releasing the manual switch button connected to the device Wiring diagram EXTERNAL KEY O LED BELL TYPE BUTTON SW1 POWER 240V AC Example of wiring with Clipsal Saturn range 1 gang wall plate and one 30 60PBBPL Bell Press Mechanism Z Wave Operations NOTE Before including the product to your Z wave network it is advised to perform removal procedure to reset network settings The Z Wave In Wall Switch must be included into your Z Wave home network before it can send and receive Z Wave commands The Z Wave In Wall Switch can only communicate to devices within the same Z wave home
4. network Always follow your controller s specific instructions for Z Wave inclusion exclusion associa tion and control operations Inclusion to Z wave home network general instructions The Z Wave In Wall Single Switch must be included into your Z Wave home network before it can send and receive Z Wave commands The Z Wave In Wall Switch can only commu nicateto devices within the same Z wave home network Always follow your controller s specific instructions for Z Wave inclusion exclusion associationand control operations 1 Connect the Z Wave In Wall Single Switch to the load power circuits and to the manual switch as per instructions in the section INSTALLATION above 2 Start inclusion procedure on your controller and when requested press and release the button on the connected Bell switch During the whole procedure controller Gateway and Z Wave In Wall Single Switch must be in close proximity of 15cm Successful inclusion will be indicated by your Z Wave remote controller Gateway In case inclusion was not successful try the procedure again or reset network settings by running exclusion procedure see below Once the Z Wave In Wall Switch has been added into your Z Wave home network successfully you may need to assign it to a specific button on your controller Gateway Refer to your Z Wave controller Gateway panel for instructions on how to do this 4 Now you can control your light via your Z Wave Gateway or other
5. r vice agent or similarly qualified person in order to avoid a hazard DO NOT INSTALL THIS DEVICE INSIDE SEALED INCLOSURES AND METAL BOXES ALWAYS LEAVE ROOM FOR VENTILATION INSTALLATION MUST BE DONE BY CERTIFIED ELECTRICIAN Technical Specifications RF Protocol Z Wave device type Connections type Operating Voltage MaxLoading Switch type RF Frequency Operation Range Application Operation temperature Storage temperature Weight Housing Dimensions LxWxH Compliance RCM Z Wave Z Wave Binary Switch routing slave See wiring above AC 240V 50Hz 6A Universal relay 921 42Mhz AU NZ approved RF for Z Wave Up to 30m when no obstacles Indoor use only 0 55 C 10 80 C 70g ABS 48mm x 45mm x 18 mm AS NZS 4268 2008 AS NZS CISPR 14 1 IEC60669 2 1 N5496 Specifications are subject to change without further notice The information in this document is subject to change without notice Digital Home Systems Pty Ltd DHS does not make any representations or warranties implied or otherwise regarding the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any commercial damage including but not limited to special incidental consequential or other damage TRADEMARKS All trademarks and registered trademarks are the property of their respective owners or companies DHS One 1 Year Limited Warranty Digital Home Systems Pty Ltd warrants this DHS b
6. randed hardware product against defects in materials and workmanship under normal use for period of one 1 year from the date of retails purchase by the original enduser purchaser Warranty Period PLEASE NOTE breaking security label will void the warranty Terms and conditions To see complete terms and conditions browse to http www digitalhomesystems com au images stories DHS_Terms_and_conditions pdf Product of Digital Home Systems Pty Ltd See all range of compatible devices at www digitalhomesystems com au Enquiries Sales and Marketing Email office dhsys com au 2012 Digital Home Systems Pty Ltd All rights reserved
Download Pdf Manuals
Related Search