Home

Users Manual - Ardy Electronics Ltd

1. The password function is by default ON but it is possible to turn it off with the Master Smart Card inserted and with Activation ON To turn it OFF or ON press SHIFT followed by 4 the display will then show PASSWORD ON CONFIRM If you confirm the change of the password function press 4 once again and the display will show PASSWORD OFF The password function is now turned OFF To turn it on again proceed as above E g SHIFT 4 4 and the display will show PASSWORD ON SLF2000 Users Manual Page 23 5 1 4 Configuration of the System The SLF2000 encryption system has several different parameters that is programmable by the user It is possible to change these parameters with the Master Smart Card inserted and Activation ON Every time the system is deactivated Activation OFF and then activated again Activation ON the parameters will be put in default state according to the data programmed in the Master Smart Card It is possible to order Master Smart Cards with different parameter values than those that is stated as default contact ARDY Electronics Ltd for more information To change or control the parameter programming of the system press SHIFT followed by 8 with the Master Smart Card inserted and accepted and with Activation ON The display will then show Parameter 0 Value 1 This is showing that Parameter O has th
2. SHIFT and KEY ZEROIZE 2 The display will then show after password entry if the password function is ON KEYS ZEROIZE CONFIRM If you confirm the command by pressing KEY ZEROIZE once again the display will show KEYS ZEROIZE ZEROIZING KEYS After this all stored keys will be erased and the security officer have to load new encryption keys and short keys to the system ENTER SHort KEY For input of short keys press SHIFT and then ENTER SH KEY 5 The display will then show after password entry if the password function is ON SH KEY ENTRY _ Now put in the number of the short key to program 0 9 and then the 30 characters in the key input as in 4 2 After all 30 characters in the key has been entered the display will show SH KEY ENTRY X UPDATING SH KEY Now the operator has stored one short key that later can be loaded to the encryption processor For loading of short keys see section 4 5 SLF2000 Users Manual Page 17 4 5 GET SHort KEY For loading of stored short keys to the encryption processor press SHIFT and GET SH KEY 6 The display will then show GET SH KEY _ Prg 0123456789 The numbers in line 2 of the displays shows which of the short keys that is programmed If some or all of the numbers in line 2 isn t shown on the display that indicate that these short keys are not programmed Now the operator has to choose one of the te
3. if the user tries to transmit a fax message the SLF2000 system will abort the transmission The SLF2000 system receives fax messages as normal in this state When a valid User Card is inserted the SLF2000 turns ENCRYPTION ON and allows transmission the user has the possibility to turn off the ENCRYPTION by pressing the SECURE key as normal When a fax message has been transmitted or after 5 minutes the SLF2000 will return to the state above Insert USER Card To send a new fax message the user has to reinsert the User Card Appendix 2 User Card stop codes It is possible to block up to 10 different User Card to use a specific SLF2000 system This is done by inserting a valid Master Card and pressing SHIFT 7 the display will then show USER STOP CODES CODE 0 If the stop code is unprogrammed it is indicated with if the stop code is programmed this is indicated with CODE 0 xXYZW XYZW is the User Card serial number which is shown on the display when the card is inserted To see the next stop code press 0 The stop codes is numbered 0 to 9 If you like to change a stop code press the SHIFT key the display will then show USER STOP CODES CODE 0 SLF2000 Users Manual Page 46 This is the User Stop code edit mode which is indicated by a line under the current serial number digit position If you enter the 4 digits of the serial number you want to blo
4. Power supply The main power for Version 2 9 is 240V 50 Hz It is also possible to get SLF2000 with the main power 110V 50 60 Hz Make sure that the main power is correct and for safe operation the system shall be connected to ground 7 2 Fuse The main fuse is 1 Amp T 5x20 mm 7 3 Front picture 7 4 Back picture SLF2000 Users Manual Page 40 7 5 Principal diagram SLF2000 Users Manual Page 41 8 QUICK GUIDE SLF 2000 8 1 Quick guide Master Smart Card SHIFT SECURE SECURE Activation ON OFF SHIFT 3 Change Password SHIFT 4 4 Password ON OFF SHIFT 8 Parameter programming 9 Change value 0 Change parameter SHIFT Program SECURE Quit Parameters 0 Encryption keys on display 0 show as characters 1 show as 1 Password on display 0 show as characters 1 show as 2 Encryption ON OFF mode Value At Power On Function 0 OFF ON with User Smart Card ON with time out to OFF 1 OFF ON with time out to OFF 2 ON OFF with time out to ON 3 OFF No time out 4 ON No time out 5 ON Only ON allowed 6 OFF Only OFF allowed 3 Encryption text ON OFF mode O no fax is marked 1 Encrypted fax is marked 2 Not encrypted fax is marked 3 Both 1 amp 2 above 4 User assigned Pin code O UAP not required SLF2000 Users Manual Page 42 1 UAP required 5 6 7 Don t change Modem levels 8 Automatic load reload of encryption keys O No automatic load 1 Au
5. 1 Error Codes for Master Smart Card Description of Error 001 Invalid Version Card version and SLF2000 version incompatible 002 Invalid MASTER The Master Card inserted have different identity than the card which activated the system 032 Invalid application code The Card is not a Master Card 048 063 The Card doesn t answer correctly 128 255 Initialisation of card is bad Error codes higher then 32 are fatal if such error codes appear please contact ARDY Electronics 6 4 2 Error Codes for User Smart Card Error Code Description of Error and SLF2000 version incompatible will not work in this system The card is not a User Card 128 255 Initialisation of card is bad Error codes not shown above or error codes higher then 32 are fatal please contact ARDY Electronics SLF2000 Users Manual Page 36 6 5 Errors when Smart Card command is used To be able to use the different Smart Card commands it is necessary that the Card is accepted when it is inserted But even if the Card is accepted it is possible that some errors occur during the use of the Card 6 5 1 Command Activation ON OFF with Master Smart Card If the card inserted is accepted as a Master Smart Card it should be no errors when the encryption is activated Activation ON or deactivated Activation OFF But it is possible that an error code of the form Activation OFF FAILED XXX is shown on the display All error
6. Automatic ENCRYPTION ON see section 4 9 A no 0 1 0 gt CSI Block not marked when transmitting encrypted faxes DEFAULT 1 gt See section 3 11 0 gt The system will not be able to work like an IDF 2000 DEFAULT 1 gt IDF 2000 mode is available The programmed parameter values are stored in permanent memory and will not be lost during power failure 4 5 6 7 10 11 To reset all parameters to the default state deactivate the system Activation OFF press SHIFT SECURE SECURE with a valid Master Smart Card inserted Then press SHIFT SECURE SECURE once again to activate the system Activation ON and load the default configuration from the Master Smart Card l For more information about the UAP see section 5 2 SLF2000 Users Manual Page 25 5 2 User Smart Card The User Smart Card is used for distribution of keys to the SLF2000 encryption system When the User Smart Card is delivered it is blank which means that the User Smart Card has no keys stored and has not been initiated with the Master Smart Card identification The Master Smart Card identification stored on the User Smart Card is a protection against unauthorised use in other SLF2000 encryption system Once the User Smart Card has been programmed with a Master Smart Card identification it is only possible to use the User Smart Card in SLF2000 encryption systems that is activated with M
7. ENTER PASSWORD INVALID and it will not be possible to proceed with the requested commana If the password function is OFF the commands will start immediately without any password entry SLF2000 Users Manual Page 15 4 2 KEY ENTRY For input of encryption keys directly to the encryption processor press SHIFT followed by KEY ENTRY 1 The display will then show after password entry if the password function is ON KEY ENTRY No1 Now input the first 10 characters of the key from the keyboard allowed characters is 0 9 After the first 10 characters the display will show KEY ENTRY No2 Enter the next 10 characters of the key And when the display shows No3 on line 2 enter the last 10 characters of the key The encryption unit will then load the key to the encryption processor this is indicated with KEY ENTRY LOADING KEY It is only possible to load 3 encryption keys within 10 minutes If the 10 minute lock is active the display shows ENCRYPTION OFF READY If the operator tries to load new encryption keys when the 10 minute lock is active the display shows KEY ENTRY LOAD NOT ALLOWED After 10 minutes has passed the display will show ENCRYPTION OFF READY and new encryption keys can be downloaded to the encryption processor again SLF2000 Users Manual Page 16 4 3 4 4 KEY ZEROIZE If short keys and encryption keys has to be erased and destroyed press
8. below Sep Encry AUTO YES ON and OFF Encry ON only with 5 minutes User Card Encry AUTO YES ON and OFF Default 5 minutes 2 Encry ON YES AUTO and OFF 5 minutes Ency on no 0 1 3 4 5 NO Encry ON NO Encry AUTO YES OFF 5 minutes Only OFF and AUTO allowed E A IO EE The automatic turn on of encryption only works when the display shows ENCRYPTION AUTO In the state ENCRYPTION ON or OFF will the system stay in the chosen state independent of if there is a system installed or not at the receiving fax SLF2000 Users Manual Page 21 5 SMART CARD MANAGEMENT 5 1 Master Smart Card The Master Smart Card is used to activate and deactivate the system With the Master Smart Card it is also possible to configure the system in different ways 5 1 1 Activation and Deactivation of the system Activation and deactivation is described earlier in this manual see section 2 2 When the system is activated data from the Master Smart Card is loaded in the encryption systems permanent memory The configuration of the system will be put in default state when it is activated The default configuration is described in the next sections of 5 1 Before it is possible to change the configuration of the system is should be activated e g the display will show with inserted and accepted Master Smart Card Activation ON READY Every Master Smart Card has an identity the identity code of the Maste
9. diagram iii ha vag padaactenden a a aa 41 QUICK CGUIDE SEF 2000 cita liada 42 Quick guide Master Smart CardO oooocococcccccccnccccncnnccccnccnancnnnnnnnnnn nn nono ncnnnncnnnos 42 Quick guide for User Smart Card cooooooccccocccccccccnncccnccnccnancnnnnn naar nono nono nn nncnnnos 44 Quick guide for use of the system Memory oooccccccccconcncncnancnaannnnnononnnnnnnnnnnos 44 Quick guide for other COMMANAS cccccccccccnccnnnccnnnnnnncnnnnannncnoncnnncnnnnnnn 44 Appendix 1 User Card required for transmission 46 Appendix 2 User Card stop codes 46 Continuous development and improvements is one of our policies Therefore we reserve the right to change specifications and functions of the SLF2000 encryption system without notice SLF2000 Users Manual Page 3 1 SYSTEM DESCRIPTION 1 1 General Description of the System Sec Line Fax 2000 Version 2 9 is an advanced encryption system for facsimile communication The system can be connected to all types of Group 3 facsimile terminals The system shall be installed between the telephone line and the telefax terminal This version 2 9 is compatible with CCITT T 30 standard of October 1984 The encryption system eliminates all special functions which are not included in the CCITT standard When the system is installed on the telefax line all incoming fax that are unencrypted can be received as normal When transmitting encrypted fax messages the transmitting operator cho
10. display will then show after UAP input if required STORE SHORT KEYS Programming 030 The digits will then count upwards until the last key is programmed 39 the message on the display will end with Programming No when the SLF2000 sends the command to update the number of stored keys to the card If you get any Error Messages see section 6 for more information The 10 short keys is now stored as key no 30 short key 0 to no 39 short key no 9 in the User Smart Card By using the ENTER SHort KEY command and this command it is possible for the User to store his own keys on the User Smart Card It is also possible to copy keys from one card to another by first using the command in section 5 2 4 LOAD 10 SH KEYS and then this command The SLF2000 encryption system always store keys to the first free location on the card key no 30 in the previous example It is not possible to erase any keys on the User Smart Card without using the KEY LOADER unit supplied by ARDY Electronics Contact ARDY Electronics Ltd for more information 5 2 8 Automatic loading of keys from User Smart Card By programming parameter 8 to 1 or 2 is it possible to get automatic load and reload of keys when a User Smart Card is inserted or deleted When parameter 8 is 1 a encryption key from the User Smart Card will be loaded automatically to the encryption processor when the User Smart Card is inserted Observe that this function requires that
11. encryption system will receive the message as normal SLF2000 Users Manual Page 9 3 4 3 5 Encryption key management The encryption system version 2 14 has both manual key management and key management by using Smart Card For information how to use the key management with Smart Card see section 5 2 The encryption keys can be entered from the keyboard or loaded from a Smart Card Each encryption key is 30 characters long The system can store 10 keys in its permanent memory as short keys 0 9 For safety these encryption keys should be put in to the system by two different persons who each know 15 characters The 10 short keys can also be loaded from the Smart Card see section 5 2 The user then only loads one of the 10 different encryption keys according to a preplanned schedule The security officer shall have an emergency plan for fast change of encryption keys in all encryption systems This is in case any system disappears from its normal location The encryption system shall be located at a safe place and not exposed to unauthorised people In case of emergency all the encryption keys can be zeroized from the system keyboard just press the keyboard SHIFT and KEY ZEROIZE followed by password if required and the KEY ZEROIZE once again to confirm the destruction of all the keys All loaded keys will be destroyed including the 10 short keys Self test When the encryption system is
12. powered up the system runs a selftest routine If this test is correct the display shows Selftest Running PASSED After this test the system is ready for operation if some error occurs the display will show Selftest Running FAILED xx xx is an error code that tells more about the error see section 6 Error Messages SLF2000 Users Manual Page 10 After this message the display will show either HARDWARE ERROR CALL FOR SERVICE SV Card Required In both cases the system needs service from ARDY Electronics Ltd or The selftest routines tests the modem circuits the RAM memory the program memory the resident encryption data and the encryption processor 3 6 Display The encryption system display is a 2 row 16 characters alphanumeric display This display shows different information during the operation of the system Normally it is possible to see the transmission speed and the standard designation for the chosen transmission speed It is also possible to get more technical information on the display if SHIFT and key 0 is pressed The display then shows MODE NORMAL CONFIRM If you then press 0 once again the display will show MODE DIAGNOSTIC READY Now the display will show all handshaking information that occurs during the fax communication To get to normal press SHIFT and 0 twice and you will get normal mode again SLF2000 Users Ma
13. so that the display will show ENCRYPTION ON READY Now the system is ready for encrypted fax transmission Start the transmission from the fax terminal as normal During transmission the display will show something like this TRANSMITTING ON V 29 9600 bps The ON after TRANSMITTING is telling you that the encryption is turned ON If different encryption keys are installed in the transmitting and the receiving system or if the receiving system has no encryption system installed the transmission will fail and the encryption unit will show COMM ERROR NO MESSAGE For more about encryption key management see section 3 4 and section 5 2 Receiving encrypted and unencrypted fax messages Since it is the transmitting operator who decides if the fax message should be encrypted or not the decryption of encrypted fax messages is automatic the receiving operator only has to ensure that both the receiving and the transmitting system has the same encryption keys installed If different keys are installed no fax message will be transmitted or received As an information to the receiving operator the transmitting system will put the text CARD ID ENCRYPTED by ARDY on the top of the fax message This message is turned ON by default when encrypted fax messages are sent but it is possible to turn it off by using the Master Smart Card See section 5 1 If the fax message received is unencrypted the
14. Users Manual SLF2000 Page 1 SEC LINE FAX 2000 SECURITY LINE for FAX MODEL 2000 USERS MANUAL Version 2 91 2002 04 03 ARDY Electronics Ltd P O Box 47 S 701 40 Orebro SWEDEN Phone No 46 19 247010 Telefax No 46 19 247011 e mail info ardy se www ardyelectronics com Copyright c 1989 2002 Ardy Electronics Ltd Ardy Electronics Ltd CONTENTS SYSTEM DESCRIPTION lt a ada 4 General Description of the SySteM oooooocconcccccnnccccccncccccccnanconnnanann nono nn nn nnnno 4 INSTALEATMON i cae A E eee eal ah 5 OWE I SUNY aah yeaah fan A A vanserv eva etates aks avevebntisity antatsees 5 Activation OF THE Ss 5 Line installation cca 25 9 Gee ceeeehcches aes Seetepany scnttes wanesebaneadeigcssbaccenennecheceeesetervecy ia 7 GENERAL OPERATION ista A tebe tetera tad 8 Transmitting unencrypted Fax Messages cooccccoccoccooocccconccnnnnnnnccnnnncncnnnannannnns 8 Transmitting ENCRYPTED Fax Messages ooccccoococcoccccocccnnnconnccnnncnancnnnnnnnnnns 9 Receiving encrypted and unencrypted fax Messages oooooocccccccnccnnnnccccncnnnnn 9 Encryption key ManageMent ccccccccccccnccnnnnconccnnnnnnnnccnonenonnnnnnnnnnnannnannnnnnns 10 Self testen OS 10 DIS play iii A A as 11 KOy Oa cit rial ciar 12 SMart Card ed cidade 12 Physical KOY scores a ra aa a aidudiandebndtatadthd cancertaleetuasa tae iatesns 12 Messages on the FAX ici dt cla 12 Messages to the Transmitting fax ooonnnnnccnnncinnnconnccnnenconnnnncnnnnnnnnnnn
15. a reference to the key that is to be loaded automatically is programmed on the User Smart Card This reference can be changed by pressing SHIFT 5 with a User Smart Card inserted and parameter 8 set to 1 or 2 When parameter 8 is set to 2 the previous loaded encryption key will be reloaded when the User Smart Card is deleted For more information about this function contact ARDY Electronics Ltd SLF2000 Users Manual Page 33 6 ERROR MESSAGES 6 1 After Power On Error Message Cause of Error HARDWARE ERROR Selftest routine detects Contact ARDY Electronics CALL FOR SERVICE hardware errors for service SV Card Required Internal encryption Turn Power off and contact service data is corrupted for service When the above messages appear on the display you have to send your SLF2000 to ARDY Electronics for service The selftest routine will in some cases give you more information about the error with the message Selftest Running FAILED XX Where XX is a hexadecimal combination of the following errors Modem circuit 1 clock failure Modem circuit 2 clock failure Encryption processor failure All error codes can be combined and the maximum error code is F8 Hex SLF2000 Users Manual Page 34 6 2 During RECEIVING and TRANSMITTING of fax messages COMM ERROR One of the faxes at the Check the faxes NO ANSWER receiving or transmitting side does not answer COMM ERROR No message recei
16. ard will become locked If you don t remember your UAP then the card will be unusable since it is not possible to unlock a Card when you don t know the UAP It is possible to use User Smart Card without UAP but it is not recommended If you want to force every User to have User Smart Card with programmed UAP program parameter 4 to value 1 see section 5 1 4 SLF2000 Users Manual Page 27 If a User Smart Card without an UAP is inserted in a SLF2000 encryption system with parameter 4 1 you will always get the question Program UAP Confirm SECURE And the card will not be accepted until an UAP is programmed 5 2 2 How to use the User Smart Card As mentioned earlier in section 5 2 the User Smart Card is used for distribution of keys But when it is delivered it has no keys stored There is two ways to generate keys to be stored on the User Smart Card manual or automatic With the normal SLF2000 encryption system it is only possible to store keys manually if you want to generate and store keys automatically please use the KEY LOADER unit supplied by ARDY During the use of User Smart Card you will have to enter the Password if UAP isn t programmed or the User Assigned Pin if UAP is programmed to be able to load and store data from to the card The UAP question UAP 5 ENTRY No _ When this question is shown on the display always enter the correct UAP otherwise the command will be aborted with an error message
17. aster Smart Card with the same identity as the one that is stored on the User Smart Card It is possible to get the User Smart Card delivered with keys stored contact ARDY Electronics Ltd for more information Each User Smart Card is able to store 100 keys 0 99 The User Smart Card can also be programmed with a User Assigned Pin UAP if the UAP is programmed the User has to enter a 5 digit code every time he wants to use his card If the wrong UAP is used 3 times in a row the card will become locked If the card is locked it is impossible to use it before it is unlocked contact ARDY Electronics Ltd for more information 5 2 1 Using the User Smart Card the first time When the User Smart Card is delivered it is as mentioned above blank When a blank User Smart Card is inserted in a SLF2000 with Activation ON the SLF2000 will detect that the card is blank and give you the following question on the display Init USER Card Confirm SECURE If you confirm this question by pressing SECURE the SLF2000 will program its Master Smart Card identity on the User Smart Card The Master Smart Card identity is stored in the SLF2000 when it is activated Activation ON Before you program the Master Smart Card identity on the User Smart Card it is not possible to use it After the programming of Master Smart Card identity it is only possible to use the User Smart Card in units that is activated by Master Smart Card
18. ck the display will show USER STOP CODES CODE 0 XYZW and the User Card with serial number XYZW will not be valid in the SLF2000 system If you want to erase a stop code press SHIFT while you are in the User Stop code edit mode The USER STOP CODES mode is finished by pressing SECURE When a User Card is in the stop code list you will get the message INVALID 011 if the User card is inserted SLF2000 Users Manual Page 47
19. command please see section 6 for more information SLF2000 Users Manual Page 30 5 2 5 GET KEY from User Smart Card For loading of keys stored on the User Smart Card to the encryption processor press SHIFT and GET SH KEY 6 The normal GET SH KEY see section 4 5 is disabled with User Smart Card inserted The display will then show after UAP or Password input SMART CARD GET KEY No _ Enter the number of the key that you want to load to the encryption processor 2 digits from 00 99 The display will then show SMART CARD RECEIVING SH KEY If you get any Error messages after the previous shown message consult section 6 0 for more information If the load was successful the display will show SMART CARD LOADING KEY Ifthe 10 minute lock see section 4 2 and 4 5 is active the display will show ENCRYPTION OFF LOAD NOT ALLOWED When the 10 minute lock is active this is indicated on the display by ENCRYPTION OFF READY XYZW when the User Smart Card is inserted After 10 minutes has passed the display will show ENCRYPTION OFF gt READY XYZW lt now a new Smart Card key can be downloaded to the encryption processor SLF2000 Users Manual Page 31 5 2 6 CONTROL Smart Card Key If a key is loaded from the User Smart Card with the GET KEY command it is possible to verify which key that is loaded Press SHIFT and CONTROL SH KEY 7 The disp
20. displayed As mentioned earlier the card will become locked if you give the wrong UAP three times in a row When you insert a User Smart Card in a SLF2000 encryption system the display will show SMART CARD If the card has UAP programmed you will then get the UAP question as told above Enter the correct UAP and the display will show if UAP is not programmed this message will be shown without any UAP input SMART CARD VALID SLF2000 Users Manual Page 28 If the User Smart Card is invalid for some reason or if you give the wrong UAP the display will show SMART CARD INVALID XXX See section 6 0 for more information about the error codes If the User Smart Card is accepted the display will show gt READY XYZW lt This is an indication from the SLF2000 that the card inserted is a valid User Smart Card You have to have this message on the display before it is possible to use the different functions supplied for the User Smart Card The XYZW is the four least significant digits in the User Card serial number These four digits will be transmitted as a part of the fax messages if the fax is encrypted and the message XYZW CARD ID ENCRYPTED by ARDY is turned on see 3 10 and 5 1 4 5 2 3 Number of keys on the Card If you want to know how many keys that are stored on the User Smart Card press SHIFT followed by 3 with the valid User Smart Card inserted The display will then
21. e can be marked with XYZW CARD ID ENCRYPTED by ARDY this message is added to the fax message by the transmitting SLF2000 The XYZW is the four least significant digits in the Serial number of a inserted valid User Smart Card If no User Smart Card is inserted these digits will not appear on the fax SLF2000 Users Manual Page 12 3 11 Messages to the Transmitting fax If parameter 10 is set to 1 see section 5 1 4 the SLF2000 encryption system will mark the CSI block of the handshake with an E in all empty positions if the transmitted fax was sent encrypted This information can later on be examined when a traffic report from the fax is printed If the SLF2000 is put in the IDF 2000 mode the CSI block will be marked with an I in all empty positions see 3 12 E g all transmitted encrypted faxes can be identified on the traffic report Example of traffic report with parameter 10 1 No Date Time TR_ ID 1 10 05 08 53 G3 T EEEE46E19E270860 lt Encrypted 2 10 05 08 54 G3 T 46 19270860 lt Not encrypted 3 10 05 08 55 G3 T 1111461191 270860 lt IDF Control 3 12 Compatibility with IDF 2000 If parameter 11 is set to 1 see section 5 1 4 the SLF2000 encryption system will have the possibility to work as an IDF 2000 system when transmitting telefax messages to telefax terminals equipped with an IDF 2000 When parameter 11 is set to 1 the ID check mode is activated by pressing SHIFT SECURE t
22. e initial message STORE SHORT KEYS CHECKING WAIT It is possible that an error message like this is shown STORE SHORT KEYS Chk Err YY XXX SLF2000 Users Manual Page 38 The meaning of the different error codes are Error Code YY Description of Error 01 All 10 short keys are not programmed XXX shows the number of the first unprogrammed short key 04 The card is in the state XXX numbers of PIN errors This command only works when the card is in the state 0 errors Reinsert the card and give the correct UAP There is no room one the card to store 10 keys XXX shows the number of the 10 th key to be stored 12 If any other error occurs during the check please contact ARDY Electronics since all other errors are fatal When the short keys are programmed on the Smart Card it is possible that the error message below will be displayed STORE SHORT KEYS Str Err YY XXX The meaning of the error codes are Error Code YY Description of Error 01 XXX describes the error XXX has the same meaning as error codes when the card is inserted The only error that should be shown is XXX 006 gt Wrong UAP 02 Error when the key is programmed Contact ARDY Electronics 6 6 Other Error Messages If any other Error Message than those shown earlier is displayed please contact ARDY Electronics since any such error is fatal SLF2000 Users Manual Page 39 7 OTHER DATA 7 1
23. e programmed value 1 If you want to change the value press 9 to step the parameter value to the wanted state For instance if you want parameter O to have the value O press 9 until the display shows Parameter 0 Value 0 To program this new value into the encryption systems permanent memory press SHIFT the display will then show Parameter 0 Programming 0 The new value is now programmed To change the parameter press 0 until the display shows the parameter number you want to change For instance if you want to change parameter 3 press 0 three times and the display will show Parameter 3 Value 1 Proceed as described above to change the parameter value To end the Parameter programming routine press SECURE or wait for the keyboard time out app 30 seconds SLF2000 Users Manual Page 24 The parameter values has the following meanings po O Imputofkeysshownasdigits po 1 Inputof keys shown as DEFAULT 1 Input of password shown as digits a Input of password shown as DEFAULT 0 7 Encryption ON OFF mode see 4 9 3 O Faxmessagesarenotmarked Eee ENCRYPTED by ARDY SLF2000 NOT ENCRYPTED 4 0 UAPnotrequired on USERS card DEFAULT 1 UAP required on USERS card 1 0 3 Output level of MODEM DEFAULT 3 Don t change without consulting the Da GENERAL MANUAL consulting the GENERAL MANUAL DEFAULT 0 0 2
24. emory If autoload is chosen with the Master Card para 8 1 or 2 it is possible to change the key to be loaded automatically with this command Download 1 encryption key from the Smart Card direct to the encryption processor 00 99 Verify the loaded key 00 99 Store 10 encryption keys from the systems memory to the Smart Card 8 3 Quick guide for use of the system memory SHIFT 5 SHIFT 6 SHIFT 7 Input 1 complete encryption key to one of the 10 positions in the system memory shortkey 0 9 Download 1 encryption keys from the system memory to the encryption processor 0 9 Verify the loaded shortkey 0 9 8 4 Quick guide for other commands SHIFT 1 SHIFT 2 SECURE SLF2000 Users Manual Input of encryption key from the keyboard direct to the encryption processor 30 characters Erasure of all encryption keys in the system memory and in the encry ption processor Not in Smart Card Encryption ON OFF AUTO Page 44 SHIFT SECURE IDF 2000 mode para 11 must be 1 SLF2000 Users Manual Page 45 Appendix 1 User Card required for transmission If parameter 2 is set to 7 see SLF2000 Users Manual section 4 9 and 5 1 4 the SLF2000 system require an inserted User Card to allow transmission When parameter 2 is set to 7 the display will show ENCRYPTION OFF Insert USER Card In this state it is not possible to transmit any fax messages without inserting a User Card
25. he display will show NEW PASSWORD No If the old password entered was incorrect the command will be aborted and the display will show INVALID on line 2 Enter the new 5 digit password After the first input of the new password you have to verify the new password If the verification was correct the password will be changed and the display will show VERIFY PASSWORD PASSWORD CHANGED SLF2000 Users Manual Page 14 If the verification is incorrect the display will show VERIFY PASSWORD INVALID and the new password is not activated and stored the old password will still be unchanged 4 1 3 Normal use of the Password When the password function is activated see 5 1 the commands KEY ENTRY see 4 2 KEY ZEROIZE see 4 3 and ENTER SH KEY see 4 4 will require a correct password entry before it is possible to execute the commands Some of the card functions will also require a correct password entry in some cases See section 5 2 If the password function is activated the encryption system will respond to the mentioned commands with ENTER PASSWORD No Before it is possible to execute the command the 5 digit password has to be entered If the password entered is correct the command will start immediately after the password input To proceed with the command follow the instructions in the following sections If the password entered is incorrect the display will show
26. he display will then show ID CHECK ON READY 3100 The four digits after READY is the SLF2000 Master identity this identity will be sent over the telephone line to make it possible to control that the receiving side have the same identity The transmitted fax will be marked with 3100 UNIT ID CONTROLLED by ARDY This mode always time outs to the default start up state after approx 5 minutes For more information about this mode please consult the IDF 2000 Manual SLF2000 Users Manual Page 13 4 KEYBOARD FUNCTIONS 4 1 Password management 4 1 1 Activation of Password When the SLF2000 encryption system is delivered the password function is ON by default The default password is 55555 If you want to deactivate the password function see section 5 1 for more information 4 1 2 Changing the Password When the previous stored password is known it is possible to enter a new password from the keyboard without using the Master Smart Card If the previous stored password is not known you have to use the Master Smart Card to change it To change a known password follow the steps below Enter SHIFT and then key 3 the display will show OLD PASSWORD No If the password function is OFF see section 5 1 the encryption system will respond with OPERATOR ERROR if you try this function When you get the message above enter the 5 digit password If the password entered is correct t
27. ill show If you want to activate the system push SHIFT followed by SECURE the display will now show Activation OFF CONFIRM To confirm the activation of the system press SECURE once again and the display will show SLF2000 Users Manual Page 5 For versions after V 2 13 the information will be automatically loaded into the system and show Activation OFF LOADING DATA while the system loads data from the Master Smart Card If the loading was successful the display will show Activation ON READY after a short while After this the system is activated and can be used by the operator For further information about the set up possibilities with the Master Smart Card see section 5 1 Master Smart Card If you get any Error messages such as SMART CARD INVALID 032 consult section 6 Error Messages for more information about the error After the activation of the system you shall take out the Master Smart Card and keep it secure If you send the system to other locations you must deactivate the system with the Master Smart Card If the system disappears during transportation it can not be used by anyone before it is activated again If you like to deactivate the system Activation OFF proceed in the same manner as described above E g insert Master Smart Card and press SHIFT SECURE SECURE and the display will show Activation OFF READY The system
28. is now deactivated and you can take out your Master Smart Card SLF2000 Users Manual Page 6 2 3 Line installation Disconnect the telefax terminal from the telephone line and install the encryption system to the line by connecting the telephone cord to the socket marked LINE on the back of the encryption system Connect the telefax terminal to the socket marked FAX The modular connector is of the model 6 4 with the default connection to the two middle poles If other connections are required consult ARDY Electronics Ltd for how to change the default connection To test if the installation is correct just lift the hook on the telefax terminal and wait for the line connect tone If you can hear the tone the Encryption system is correctly installed If your line connect tone is 425 15 Hz the SLF2000 will display DIAL TONE DETECT If your line connect tone is any other frequency you will not get any message on the display when you lift the hook on the telefax terminal Other frequencies then 425 15 Hz will not interfere with the function of SLF2000 the only thing that will happened is that the message above will be missing Put the telefax terminal on hook and wait until SLF2000 shows ENCRYPTION OFF READY The System is now ready to use SLF2000 Users Manual Page 7 3 1 i GENERAL OPERATION Transmitting unencrypted Fax messages It is possible to transmit an unencrypted fax message to all o
29. lay will then show SMART CARD CONT KEY No _ Now choose which Smart Card key you would like to control 00 99 If the chosen Smart Card key has been loaded to the encryption processor the display shows SMART CARD KEY MATCH OK If the chosen Smart Card key has not been loaded the display will show SMART CARD KEY MATCH FAIL Observe that this function only control the chosen Smart Card key number and never controls the actual encryption key 5 2 7 STORE SHORT KEYS to User Smart Card If all 10 short keys are programmed see section 4 4 in the encryption systems short key memory it is possible to store these 10 keys on the User Smart Card The use of this command require that all 10 short keys are programmed and that the inserted User Smart Card has at least 10 unprogrammed Card keys You activate the command by pressing SHIFT 8 the display will then show STORE SHORT KEYS CHECKING WAIT The SLF2000 is then performing a check that all 10 short keys are programmed and that there is at least 10 unprogrammed keys on the User Smart Card If the check was successful the display will show see section 6 0 if an error message is displayed STORE SHORT KEYS As 030 039 This question asks you to confirm the programming of the keys number 030 to 039 on the User Smart Card with the contents of short key number 0 9 SLF2000 Users Manual Page 32 You confirm the programming by pressing 8 The
30. n short keys 0 9 to be loaded to the encryption processor If the chosen short key has not been programmed the display shows ENCRYPTION OFF NOT PROGRAMMED If the chosen short key is stored in the short key memory the system loads the key to the encryption processor and the display then shows GET SH KEY X LOADING KEY Observe that if the 10 minute lock is active it is not possible to load encryption keys to the encryption processor The display will then show ENCRYPTION OFF LOAD NOT ALLOWED Wait until the display shows ENCRYPTION OFF READY now a new short key can be loaded to the encryption processor SLF2000 Users Manual Page 18 4 6 4 7 4 8 CONTROL SHort KEY If the operator wants to control which short key that is loaded if any to the encryption processor press SHIFT and CONTROL SH KEY 7 The display will then show SH KEY CONT __ Now choose which short key you would like to control 0 9 If the chosen short key has been loaded to the encryption processor the display shows HS KEY CONT X KEY MATCH OK If the chosen short key has not been loaded the display will show SH KEY CONT X KEY MATCH FAIL Observe that this function only control the chosen short key and never controls the actual encryption key Test modes By pressing SHIFT and 8 it is possible to put the encryption system in different test modes For more information abou
31. nnnnnnns 13 Compatibility with IDF 2000 oooononocccccccnnnococcccnnconcnnnncnnnnnononnnnoncnnanonnnnnncnnnn 13 KEYBOARD FUN CONS cima ta 14 Password management c ccccccccccccnncccccccnnccnonncannnnannn nn nn nn nn nro nc nnnnnnnnnnnnnnnnnnnnnn 14 Activation of Password sit is eta ehed coos 14 Changing the Password oooccccccccccccnnnconnnonnnononannnononnnonnnnnnnonnnnnnninannno 14 Normal use of the PasswoOld ooocooccccccccccnccccccccccnancnnnnnannnnnnnn nn nn n nn ncnnnos 15 A A O 16 KEY ZEROIZE Scania ida bas 17 ENTER SHOrtKEY cocina ora me 17 GET SHORE Y ida 18 CONTROL SHOT KEY nippa aa a O a iea a a aeiaai 19 Testmodes ii it 19 S E E AE T A A A EEE 19 SECURE ON OFF AUTO arrine i e a ARE E 20 SMART CARD MANAGEMENT occccccooccnccncononnnnnncnnnncnnnnnnnnonnnnnnnnnnnrncnnnnnannennnnaneninns 22 Master Smart Card iii a i 22 Activation and Deactivation of the system ooooonncinniccnicacocaaancnnnccnnnos 22 Changing the PASSWOrd lt lt iii 22 Selecting Password ON or OFF eesececeeeeeeeeeeeeseeeeeeeeeeeeeeeeeeteenneeeas 23 Configuration of the System ceecee eee eeeeeeeeeeeeeeeteeeaeeeeeeeeeeeeeeeeeeees 24 UserSmartCard citan dla 26 Using the User Smart Card the first time eeeeeeeeeeeeeeeeeetteeeeees 26 How to use the User Smart Card ooocconccnnnccccccccnnconnnannnananononcnnnnonnnos 28 Number of keys on the CalO oooocoooccccccccccccccccccconanccnnanannnn no nono nico nnncnn
32. nos 29 Load 10 Keys from Smart Card to Short key memory 068 30 GET KEY from User Smart Card cooocccccccccccconoocconnncnnncnnncnnnnnnnnnnnnninanos 31 CONTROL Smart Card Key ccoo AA 32 STORE SHORT KEYS to User Smart Card 00 00 ccccecccceceeceeeeeeeeeeeees 32 Automatic loading of keys from User Smart Card oooooocccccccniccccccccco 33 SLF2000 Users Manual Page 2 BRROR MESSAGES weiss e eden de cosas 34 After Power OlMiuursncstiaar a db ksa 34 During RECEIVING and TRANSMITTING of fax Messages cccccccccccccccccos 35 During KEY BOARD Operativo lis 35 When Smart Card is inserted oooocccccncicnnccccccoccconccononnnnnnncnnnnnnonononnanannccnnnnnnos 36 Error Codes for Master Smart Card oooococccnnccccccccnnnnnoococononnnnnnnnnnnnnnns 36 Error Codes for User Smart Card cooooooconnconccccononcccccnononnonannanncnnnnnnnnnnos 36 Errors when Smart Card command iS used oococccccccccccnnnnnnconncnnnnnnnnnnnnnnnnnnns 37 Command Activation ON OFF with Master Smart Card 37 Command Number of keys with User Smart Card 0 0008 37 Command Load 10 Keys with User Smart Card ooooooooooonnnocococccccos 38 Command GET KEY with User Smart Card oooooccccccccccnnnccccccnnnnnnos 38 Command STORE SHORT KEYS with User Smart Card 38 Other Error Messages ti 39 OTHER DATA dt a aleea 40 POWER dai 40 USC iia dera 40 Front PICS A AA AA tind ake 40 Back DIC lt a 40 Principal
33. nual Page 11 3 7 3 8 3 9 Keyboard Most of the keys on the keyboard has double functions To get this second function first press SHIFT and then the wanted function key With master or user Smart Card inserted the function of the keys will be different see section 5 All keyboard operations will activate the display which waits for input from the operator If input of information to the system is not carried out completely the system automatically interrupts the input and return to the default state If a wrong character has been input it is possible to erase it by pressing SHIFT and lt The function can also be aborted by pressing SHIFT twice Smart Card reader The system is equipped with a Smart Card reader to make it possible to use Master and Users Smart Card For more information about the Smart Card functions see section 5 Physical key The encryption system has an physical key for locking the system If this key is turned off the encryption system becomes inactive and the telefax terminal can be used as normal without disconnecting the encryption system 3 10 Messages on the FAX The received and transmitted faxes can be marked with different messages depending on the set up see 5 1 4 A received unencrypted fax message can be marked with NOT ENCRYPTED this message is added to the fax message by the receiving SLF2000 A transmitted encrypted fax messag
34. ose ENCRYPTION ON and the receiving system automatically decrypt the message if the same encryption key has been installed If different encryption keys are installed in the receiving and transmitting parts the fax message will not be transmitted and the system shows COMM ERROR on the display The encryption system does not influence the transmission speed but if the line quality is poor the system will decrease the speed according to the CCITT standard For more general information contact ARDY Electronics Ltd SLF2000 Users Manual Page 4 2 1 2 2 i INSTALLATION Power Supply The main power for Version 2 9 is 240 Volt 50 Hz optional 110V 50 Hz Make sure that the main power is 240V and for safe operation connect the system to ground Activation of the System When the system is delivered it is not activated with the Master Smart Card When the power is turned on the display will show Activation OFF Insert MSTR Card Observe that this message will be displayed if the initial selftest is passed if any other message is displayed consult ARDY Electronics Put in the Master Smart Card and wait until the display shows SMART CARD VALID This message is a confirmation from the system that the inserted Master Smart Card is valid After this message the SLF2000 unit is ready to accept commands from the keyboard and the display will show Activation OFF LOADING DATA Older versions of the system w
35. owed Transmission only allowed with User Card see Appendix 1 al Zz Z Z as O O O y Z O Mode 0 is a special mode which allows ENCRYPTION ON only when a valid User Smart Card is inserted E g ENCRYPTION ON will be chosen as soon as a valid User Smart Card is inserted It is however possible to but the SLF2000 in ENCRYPTION OFF by pressing the SECURE ON OFF As soon as the User Smart Card is deleted the SLF2000 will return to ENCRYPTION OFF After a successful transmission or after 5 minutes the SLF2000 will return to the default state ENCRYPTION OFF and no card accepted even if the User Smart Card is still inserted To get into the ENCRYPTION ON mode again you have to reinsert the User Smart Card SLF2000 Users Manual Page 20 If parameter 9 is set to 1 or 2 see section 5 1 4 is it possible to but SLF2000 in the state ENCRYPTION AUTO READY In this state the SLF2000 encryption system will automatically turn encryption ON when transmitting fax messages and the receiving fax has a SLF2000 installed If parameter 9 is set to 2 the system will turn encryption ON automatically only if the receiving system has the same Master Smart Card identity as the transmitting system see 5 1 1 REMARK This function only works when both the receiving and the transmitting system has version 2 4 or higher of the software With parameter 9 set to 1 the different ON OFF AUTO modes parameter 2 will function as described
36. r Smart Card is a 4 digit code of the form 3XXX where XXX is Hexadecimal digits If the system for instance is activated with a Master Smart Card with identity 3009 you must have a Master Smart Card with the same identity to deactivate the system For more information about the Master Smart Card consult ARDY Electronics Ltd 5 1 2 Changing the Password When the system is delivered the default password is 55555 If you want to change the password you can do so without the Master Smart Card if the old password is known Described in 4 1 2 If the old password is not known you have to put in a valid Master Smart Card to be able to change it With a valid Master Smart Card inserted and Activation ON press SHIFT and then 3 The display will then show ENTER PASSWORD No _ Enter the 5 digit password that you want the system to have After the first input of the password you have to verify the password before it is stored The display will show SLF2000 Users Manual Page 22 VERIFY PASSWORD No _ Enter the password once again if the password entered the second time is the same as the first one the password will be changed and the display will show PASSWORD ON PASSWORD CHANGED If the password entered the second time is different than the first one the password will not be changed and the display will show VERIFY PASSWORD INVALID 5 1 3 Selecting Password ON or OFF
37. s during activation is regarded as fatal please contact ARDY Electronics if a message like above is displayed 6 5 2 Command Number of keys with User Smart Card When this command is used it is possible that an error message as this is displayed SMART CARD INVALID XXX All error codes except 006 which is the error code for wrong UAP are regarded as fatal Please contact ARDY Electronics if such error code is shown SLF2000 Users Manual Page 37 6 5 3 Command Load 10 Keys with User Smart Card When this command is used it is possible that an error message as this is displayed LOAD 10 SH KEYS KEY Err YY XXX The meaning of the different error codes are Error Code YY __ Description ofEror 01 XXX describes the error XXX has the same meaning as error codes when the card is inserted The only error that should be shown is XXX 006 gt Wrong UAP 06 The key that you want to load is not programmed XXX shows the number of keys on the card 08 XXX is always 255 The key on the card is not correctly programmed Contact ARDY Electronics All other error codes then those above are regarded as fatal please contact ARDY Electronics if such errors occur 6 5 4 Command GET KEY with User Smart Card The error codes shown for this command are the same as the ones shown for the previous command LOAD 10 SH KEYS 6 5 5 Command STORE SHORT KEYS with User Smart Card After th
38. show after UAP input if required SMART CARD No of keys 030 This is telling you that the inserted User Smart Card has 30 keys stored Since the keys always begin with key no 00 the existing keys on this particular card has the numbers 00 29 Each card can store 100 keys SLF2000 Users Manual Page 29 5 2 4 Load 10 Keys from Smart Card to Short key memory It is possible to load 10 consecutive keys from the User Smart Card to the SLF2000 permanent short key memory This is done by pressing SHIFT 4 the display will then show after UAP or Password input LOAD 10 SH KEYS From _ Enter the number of the first User Card key to store in Short key memory 0 For instance key no 10 the display will then show From 10 to 19 This question ask you to confirm that key no 10 19 on the User Card will be stored as Short Key no 0 9 in the SLF2000 Short Key memory If you confirm by pressing 4 the SLF2000 encryption system will start to load keys from the User Card to its internal short key memory Please note that the programming of Short keys is done backwards starting by loading key 19 from the card and program Short key 9 This is indicated on the display with LOAD 10 SH KEYS Programming 09 The digits will then count backwards until it reach 00 and then end with an OK Now all 10 Short Keys are programmed with keys from the User Smart Card If you get any Error Messages during this
39. t the test modes contact ARDY Electronics Ltd SHIFT This key is only used to reach the second functions of the keyboard Always when the operator wants to use the keyboard functions start with SHIFT and then the wanted function Most of the functions can be aborted by pressing SHIFT twice SLF2000 Users Manual Page 19 4 9 SECURE ON OFF AUTO When an encrypted fax message is to be transmitted press the SECURE ON OFF until the display shows ENCRYPTION ON READY This command mode will continue or automatically return to OFF depending on the parameter set up The parameter set up is changed with the master Smart Card see 5 1 Some of the possible set ups only allows encryption ON or OFF in these cases the SECURE ON OFF key has no function The default set up is ENCRYPTION OFF and with ENCRYPTION ON with a 5 minute time out This means that if no message has been transmitted within 5 minutes from the choice of ENCRYPTION ON the encryption system automatically will return to ENCRYPTION OFF mode The different ON OFF modes is see section 5 1 for programming instructions Value Startup with On Time out OFF Time out Encry OFF YES Encry ON only with User Card Default Z O Encry OFF YES 5 minutes 2 Encry ON NO Z O 5 minutes 3 Encry OFF NO Encry ON NO Encry ON NO Encry OFF 7 Encry OFF YES Only ON allowed Only OFF all
40. ther group 3 telefax terminals on the market with the encryption system installed When you transmit unencrypted fax messages the receiving side doesn t need to have a SLF2000 installed The only thing you have to observe is that the encryption is in the encryption OFF mode The display must then show ENCRYPTION OFF READY During the transmission you can read the transmission speed on the display of the encryption system If different speeds are displayed from time to another that is because of different line quality The display will show something like this TRANSMITTING OFF V 29 9600 bps The OFF after TRANSMITTING is telling you that the encryption is turned OFF When the fax message is being transmitted the display shows different messages for the transmission When the fax message has been correctly transmitted to the receiver the display on the encryption system shows COMMUNICATION COMPLETED And then the display will show ENCRYPTION OFF READY Now the system is ready for transmitting or receiving new fax messages SLF2000 Users Manual Page 8 3 2 3 3 Transmitting ENCRYPTED Fax messages When an encrypted fax message shall be transmitted both the transmitting and the receiving side must have an encryption system installed Both encryption system must have the same encryption key installed When you want to transmit an encrypted fax message push the keyboard SECURE ON OFF
41. tomatic load of encryption key from User Smart Card to encryption processor 2 As 1 above but with reload of old encryption key when the card is deleted Automatic choice of encryption ON OFF during transmission 0 No automatic function 1 Automatic choice possible when ENCRYPTION AUTO 2 As 1 above but the same Master Smart Card identity required in the receiving and trans mitting system to turn encryption ON When this AUTO function is set to 1 or 2 the Encryption ON OFF modes parameter 2 will get the following functions Value At Power On Function 0 AUTO ON with User Smart Card ON amp OFF with time out to AUTO 1 AUTO ON 8 OFF with time out to AUTO 2 ON AUTO amp OFF with time out to ON 3 AUTO No time out 4 ON No time out 5 ON Only ON allowed 6 AUTO Only OFF amp AUTO allowed 10 11 OFF with time out to AUTO Marking of CSI string when fax is sent encrypted 0 CSI string not marked 1 CSI string marked with E or I in all empty positions when a fax message is sent encrypted or in the IDF mode IDF 2000 Compatibility 0 The system is not able to work like an IDF 2000 1 IDF 2000 mode available SLF2000 Users Manual Page 43 8 2 Quick guide for User Smart Card SHIFT 3 SHIFT 4 4 SHIFT 5 5 SHIFT 6 SHIFT 7 SHIFT 8 8 Show how many encryption keys that are stored on the Smart Card Download 10 encryption keys from the Smart Card to the system m
42. ved or __ Check the encryption keys NO MESSAGE transmitted if the fax was to be encrypted or try again 6 3 During KEYBOARD Operation If you press the wrong keys when you execute a command the display will show ENCRYPTION OFF OPERATOR ERROR Action Read the User Manual about the command you want to execute or try again maybe you just used the wrong keys Other possible errors during KEYBOARD operation are ENTER PASSWORD The entered password is Activate the wanted INVALID not correct command once again and enter the correct password ENCRYPTION OFF _ You have tried to load a Wait until the 10 minute LOAD NOT ALLOWED key when the 10 minute lock disappears lock is active ENCRYPTION OFF The encryption processor Try again if the error is KEY LOAD FAILURE failed to load the wanted shown every time you key want to load a key contact ARDY Electronics for service ENCRYPTION OFF The short key you tried to Load a programmed short NOT PROGRAMMED load is not programmed key or program the short key before you try to load it SLF2000 Users Manual Page 35 6 4 When Smart Card is inserted SMART CARD The inserted Smart Card Your card is not correct INVALID doesn t answer correctly Contact ARDY Electronics CARD LOCKED or ARDY Electronics SMART CARD Wrong Card XXX is an See error code list below INVALID XXX error code that is telling 6 4 1 2 more about the error 6 4
43. with the same identity as the one programmed on the User Smart Card While the programming is taking place the display will show SMART CARD Programming ID SLF2000 Users Manual Page 26 If the programming of the Master Smart Card identity was successful see section 6 0 if you get an error message you will get a question on the display that will ask you if you want to program a User Assigned Pin UAP on the card Confirm SECURE If the configuration of the system requires that every User Smart Card should have an UAP programmed see section 5 1 4 parameter 4 this question will not be displayed Instead you will get the message that is shown below the same message will be shown if you press SECURE as a confirmation that you want to program the UAP UAP 5 ENTRY No Enter the 5 digits 0 9 that you want to have as UAP After the first input you have to verify the input once again before the UAP is programmed the verification question will be displayed as VERIFY UAP 5 No Enter the 5 digits in the UAP once again if both the inputs is equal the UAP will be programmed this is indicated on the display with SMART CARD Programming UAP If the both inputs are not equal the UAP will not be programmed and the display will show VERIFY UAP 5 INVALID IMPORTANT Programming of UAP can only be done once If you forget your UAP and give the wrong UAP to the card 3 times the c

Users Manual - Ardy Electronics Ltd

Contents

Download Pdf Manuals

Related Search

Related Contents