Acroprint 125SP Solar Powered Mechanical Time Clock User Manual
Contents
1. TIME CLOCK WORLD 888 534 5994 Model 125SP USER MANUAL b b solar 29 power t Solar Panel Operating Instructions 1 Charge the Panel via Sunlight a Open the Solar Panel and keep it facing the sunlight as shown in Figure 1 The LED indicator on the DC 6V input will become Green indicating that the lithium battery is being charged The stonger the sunlight intensity the stronger the charging current b Charging times can range from 8 12 hours depending upon the intensity of the sun 2 Charge via USB Cable Connected to Computer a This is the process to charge the battery when direct sunlight is not available Plug the Power Charging cable into the DC 6V IN connector on the bottom side of the solar panel as shown in Figure 2 It is not required that solar panel need to be opened when using the PC s USB plug Note The Power cord and charging cord are the same The function is determined by when connector is used on the Solar Panel i Figure 2 b Connect the other end of the Power Charging cord to the USB connector on the PC The LED beside the DC 6V IN will light up indicating that the Lithium battery is charging Charging time should be approximately 6 hours for a full charge Note After the Solar Panel has been in the sunlight for at least 15 minutes the Acroprint Time Clock can be connected to the Solar Panel using the Power Charging connector but it is recommended that the2. standard Fiechargeable 15 WOE Dk Bathedes Equipped wth bullion Tock BATTERY Granger Recorder will for seerd days afer poe modd last Tar Soe Far wee in ete 110 Var ac 220 WOE AG Powersystems Toe desired vidiga mosk rw been peaded ane recode war oder Far use in Matar Venide wn 12 vat OO Tar uza in Extremely Gald Climates wiin a mugqested 12 Yai Do bead Sod Batten extern nat induded GENERAL INSTRUCTIONS Far inst uctians cowering the removal af the case cover setting the recorder changing the ribbon and general maintenance pease sea ihe enclosed General User Instructions Paraphlet The BP122 6 Recorder Your new Eatery Powe red Acraprimt Reorder is designed an four H 1 Dr D call Any make battery willbe satetacton however we recommend that vau Alkaline Bateres which shoukl provide vauwith several months of rela operation 2 BP125 Fh BP 125 12 Mi PiN ALE D PC 125 Battery Powered DC INSTALLING THE BATTERIES Ta install the batteries loosen and remove the Buterth Nut atthe tap of tha Assembly Frame which will vau ta prot the entire chock mechanism an the bottom srawe thereby allawing you ta gain azcess D tha batery holder mountdonthe inde back af he case The tap
3. Battery should have the posite terminal an the er as indicated on the batten holder The posite terminals onthe other three batteries should alternate as shown anthe battery ftw of the batteres are improper installed a red light onthe circu board which amp mounted in the upper right hand camer of the back case RED See Figure 2 If all i amp well tha recorder shaukdadwance one 1 minute within sity seconds afer the batteries have been proper hy instal bed WEAK BATTERY WAR NING When the batteries fave discharged down taa point beeper on the cirzurt board will ba actmratad Rear the beeping we recommend replacing the Batteries within five 5 days ar the recorder may begin bse time ar stop altogether Sea Figuraz j Butte th Mut Pivot TEC DEM FIGURE 1 Impr per battery Insertion ind rator Cable conn ector FIGUREZ The Rechargeable Recorder BP 125 These recarders include four 4 standard rechargeable battar IMPORTANT Before setting your recorder ta the correct tima plug the machine in forat least 15 minutes ta allow batter tes ta charge up operating wo the recorder will run sow 125 Rechargeable 120 240V Fiachargaabia Batteries ince uit boa rd The BP 12 Acroprint BOSS Recorder The 125 12 BOSS Recorder is designed to aparate ana 12 ValtA
4. Solar Panel lithium battery be fully charged before being placed into operation 3 Clock Operation with the Solar Panel a When the Solar panel has been fully charged it can be connected to the Acroprint Time Clock via the supplied Power Charging cable First connect the round 1 3mm connector to the Time Clock power jack located on the rear of the clock in the bottom right corner b Next connect the USB connector to the Solar Panel as shown in Figure 3 c After the USB connector has been plugged in move the power switch from the OFF position to the 6V position A GREEN led should illuminate indicating that the Solar Panel is now active and supplying power to the Time Clock The Clock will advance the time 1 or 2 minutes when this step is complete d Set the correct time on the Time Clock Figure 3 06 0384 000 Rev A BATTERY POWERED USER INSTRUCTIONS ACROFRIMT 125 BOSS TIME CLOCKS thank vau vary much far purchasing the Acraprirrt Batten rated with Sold State Gontraled Accuracy Time Recorder engineeringand testing hours have beenspent in producing far youan extra meh accu rate State af the Art portable Battery Powered Time Recording Devia The instructon pamphlet covers the following Acra print BJSS Recorder 1 BPizhh alone pruza win four id sanad D call 1S Mok Alkaline Dateie baenz nat induded Far ume with fr td
5. age or shortages to the company from which the unit was purchased Site Requirements The recorder should be mounted on a sturdy wall shelf or other support area Do not use the recorder under the following conditions extremely high or low temperature operating range 0 to 50 C 32 to 122 FJ extremely high or low humidity operating range 0 to 90 RH non condensing areas of high dust concentration areas with extreme vibration or when placed on an unstable or unlevel surface Mounting the Recorder and Card Racks The recorder requires an uninterrupted AC power supply and should be mounted within 6 feet of a power receptacle to accommodate the unit s power cord The suggested wall mounting layout for the recorder and optional card racks is shown in Figure 4 Suggestions for mounting on specific wall and shelf surfaces follow Figure 4 suggested mounting layout rd 32 40 RECEPTACLE Wooden Plywood Walls You may use the three screws included with the recorder to mount the recorder Install a screw in the wall 53 above the floor Leave enough of the screw protruding so the recorder will hang flat against the wall through the keyhole on back of the clock Hang and level the recorder Insert and tighten screws through the lower left and right mounting holes Masonry Walls You may use plastic masonry anchors and screws available at your local hardware store to mount the recorder Ma
6. away views The levers are behind the clock 7 Black Minute Lever Yellow Day Date Yellow Lever Day Date Month Knob turn counter clockwise dial Lever E Cr To Change Ribbon A replacement Acroprint Ribbon is supplied on two spools When ordering specify 20 106 002 for two color right margin print recorder 20 106 000 for two color left margin print recorder or 20 0106 003 for solid blue ribbon To replace the ribbon perform the following steps 1 Note how ribbon is threaded Pull right Ribbon Tension Spring see Figure 3 forward and remove spool Pull left Ribbon Tension Spring see Figure 3 forward and remove spool Remove and discard ribbon 2 Insert new right Ribbon Spool with hex hole fitted on to hex shaft on the right ribbon feed ratchet Thread ribbon as noted in step 1 Insert new left Ribbon Spool with hex hole fitted on to hex shaft on the left ribbon feed ratchet Turn right Ribbon Spool counter clockwise to remove excess slack in ribbon Figure 3 front view with cover removed RALEIGH N C USA Ribbon Tension Spring E j Ribbon Tension Spring Ribbon Spool Ome 9 9 Installing the Time Recorder Unpacking and Inspection Carefully unpack your recorder and inspect it for any damage Verify that the following accessories are included three mounting screws a case lock key and the General Service Instructions Report dam
7. ify correct setting Repeat steps A B if reading is incorrect Figure 1 cover removed General Service Instructions Models 125 and 150 Recorders IMPORTANT NOTES 1 The date setting if so equipped MUST be manually reset to the first of the month each month following any month with less than 31 days 2 The month and year settings if so equipped MUST be manually reset every month year 3 To reset your recorder after a power failure follow the steps 1 5 4 HINT If clock is set slightly ahead of actual time you may unplug it until it matches the correct time To Set Time and or Date for Left Print Models 1 Unplug recorder and remove Case Cover 2 To Set Day Date A Follow the same steps as for standard models but note the different location of Yellow Day Date lever in Figure 2 3 To Set Time A Follow the same steps as for standard models 4 To Set Month if so equipped A Move Month Lever see Figure 2 to extreme left position then return slowly to right until an audible click is heard B Plug in recorder and punch card to verify correct setting Repeat steps A B if reading is incorrect 5 To Set Year if so equipped A Note that year set lever is located at the rear of the typehead assembly Follow the same steps as for setting the month on left print models Figure 2 left print models Month Lever Black Minute Lever Note Day Date amp Month levers are shown in cut
8. ob ike electrical services 125 Battery Powered 12V DC i 0106 200 Rev F EICROPRINT Time for Business To Remove Case Cover 1 Turn key one quarter turn clockwise 2 Lift case cover up then forward 3 Reverse procedure to replace cover To Set Time and or Date NOTE Unless your recorder is equipped with continental 0 23 hours all PM hours on the time card will be printed underscored Ex 1 00 To change the time and or date follow these steps 1 Unplug recorder and remove Case Cover 2 To Set Day Date A Make sure current time setting is between midnight and noon see note above B Push down and release Yellow Lever see Figure 1 to set correct day date C Plug in recorder and punch to verify correct setting Repeat steps A C if reading is incorrect 3 To Set Time A Push down and release Black Minute Lever to set the correct time see Figure 1 If minute lever does not work plug in recorder and wait for minute hand to advance then unplug recorder and try lever again DO NOT MOVE CLOCK HANDS TO SET THE TIME 4 To Set Month if so equipped A Turn Month Knob see Figure 1 counter clockwise to select correct month B Plug in recorder and punch card to verify correct setting Repeat steps A B if reading is incorrect 5 To Set Year if so equipped A Insert point of pen into spoke on side of year wheel and rotate counter clockwise B Plug in recorder and punch card to ver
9. rk a location on the wall 53 above the floor Drill a hole with a 1 4 masonry bit and insert a plastic anchor Tighten a screw at this location leaving enough of the screw protruding so the recorder will hang flat against the wall through the keyhole on back of the clock Hang and level the recorder Mark the location of the lower left and right mounting holes Remove the recorder drill holes and insert anchors Replace the recorder insert and tighten screws through the lower left and right mounting holes and fully tighten the keyhole screw Sheetrock Hollow Core Walls You may use molly fasteners available at your local hardware store to mount the recorder Follow the procedure for masonry walls using the molly fasteners instead Alternatively you may use longer wood screws to attach the recorder to a stud behind the sheetrock using the keyhole and the lower center mounting hole on the recorder NOTE Always consult with a professional contractor carpenter and obey all local building and fire codes when installing your recorder
10. utomobile Bate We recommend you connect the recorder directhy ta the Batten insure that constant power amp supplied Wa supp ked 2 ring terminals make the connection to your batten and 2 terminals to make the connection on the terminal block You will need to purchase hwo 2 wires in whatever length required We suggests 20 gauge stranded wire that can be purchased fram any Hardware store ar electrical parts shop you fave wire connecta ring terminalta one emd ofeach wire anda to the ather ends Lorat the six 6 position terminal block mounted ta the time recorders Back casae and connectone ofthe terminals ta ermil Ma 1 and other ta terminal Ma 2 be sure ta idantite the wire an Terminal Ha 2 by wrapping elactrician s tape araund the ring terminal because this will connected to the positive terminal an your battery Fish the wire through the firewall af the wehick ether throughan eting opening wed by air conditioning ar heating hoses ar haad release If necessary yau rra drilla hok in tha firewall ata place where there are obstructions under the haod Run the wire ta the batten and remove the battery screw ard installit hack inta the bolt see Figure 2 Follow the same procedure far the term inal Ifyou wish vau may hawa the unit protessianalh installed ata nominaltee by any specializing in autom
Download Pdf Manuals
Related Search