Instruction Manual - BLACK & DECKER® Service
Contents
1. conducted through the metal and can crack the glass Scrape with the grain of the wood wherever possible Do not linger on one spot for too long as the surface may char or ignite KX1682 KX1683 only Your heatgun is designed for use with the scraper blade to strip paint Proceed as follows Ensure the nozzle is cool and fit the scraper blade Hold your heatgun with the scraper blade in contact with the surface at an angle of 30 40 When the paint softens scrape firmly Experiment to establish the length of time necessary to apply the heat to obtain optimum results Scrape the softened paint immediately or it will harden again Take care to prevent paint and debris collecting on the scraper because it may ignite Carefully clean the scraper blade with a knife should any build up occur When scraping vertical surfaces scrape downwards to prevent debris falling into the nozzle Note When stripping a point next to glass use a glass protector nozzle instead of the scraper blade a manual scraper is needed to scrape off the paint CD700 KX1600 only Your heatgun is designed to soften paint and laquer enabling itto be removed using a good quality hand scraper Proceed as follows Directthe hot air onto the area to be removed When the paint softens scrape firmly Experiment to establish the length of time necessary to apply the heat to obtain optimum results Scrape the softened paint immediat2. s HE BLACKS DECKER KX1600 KX1682 KX1683 Congratulations CD700 KX1600 1683 UK p01 16 2 To ensure the best results from your heatgun please read these safety and usage instructions carefully If you have any questions or queries after reading this user manual please do not hesitate to call our Service and Information Centre whose number you will find towards the back of this user manual or one of our Authorised Repair Agents A list of these Agents and further information is available on the Internet at www 2helpU com 15 3 00 5 31 pm Contents Safety instructions Additional safety instructions for heatguns Double insulation Electrical safety Mains plug replacement Extension cables Unwanted tools and the environment The Black amp Decker guarantee After sales service for your Black amp Decker product Accessories Technical data Features e Handling your heatgun Operating your heatgun Cooling down Hands free use Fitting the scraper Paint stripping Other uses for your heatgun Accessories Cleaning EC declaration of conformity Black amp Decker phone numbers and addresses Guarantee card CD700 KX1600 1683 UK p01 16 3 15 3 00 5 31 pm e III Heatgun user manual SAFETY INSTRUCTIONS Maintain the tool with care Keep a cutting tool Warning When using electric tools the following sharp and clean for better a
3. as they can be caught in moving parts Rubber gloves and non skid footwear are recommended when working outdoors Wear protective hair covering to contain long hair Use safety glasses Use a face or dust mask as well if the operation is dusty or if the tool is being used in enclosed spaces Connecting dust extraction equipment If devices are provided for the connection of dust extraction and collection ensure these are connected and properly used especially in confined areas Do not abuse the cord Never carry the tool by its cord or yank itto disconnect it from the socket Keep the cord away from heat oil and sharp edges facility Inspect the extension cord periodically and replace if damaged Keep the handles dry clean and free from oil and grease Disconnect the tool when not in use before servicing and when changing accessories such as blades bits and cutters Remove adjusting keys and wrenches Form the habit of checking to see that keys and adjusting wrenches are removed from the tool and replaced in the storage area before switching on Avoid unintentional starting Do not carry a plugged in tool with a finger on the switch Ensure the switch is off when plugging in Use an outdoor extension cord When a tool is used outdoors only use an extension cord intended for outdoor use and so marked Stay alert Watch what you are doing use common sense and do not operate the tool when tired Check damaged parts Before fu
4. nozzle down thus preventing damage to the surface on which your heatgun is placed HANDS FREE USE Your heatgun is also designed for operation while placed on the stands 4 Always point your heatgun 15 3 00 5 31 pm 1 CD700 KX1600 1683 UK p01 16 8 ENGLISH away from you Secure the cable to prevent pulling your heatgun off the stand Do not touch the nozzle and ensure that nothing is dropped into the nozzle Carefully switch off your heatgun and then allow it to cool see cooling down procedure FITTING THE SCRAPER KX1682 KX1683 Ensure your heatgun is cool Align the slot of the scraper blade I with the 6 protrusion on the blade holder and position under the retaining screw Note Ensure the hole in the scraper is to the left of the screw in the blade holder Tighten the retaining screw Place the blade holder over the nozzle outlet Ensure it is aligned The small bump on the inside of the blade holder engages with the recess on the nozzle Tighten the blade holder clamp screw PAINT STRIPPING When stripping a point next to glass it is necessary to protect the glass from the heat A Black amp Decker glass protector nozzle is used for this purpose available as an accessory Your heatgun is not suitable for stripping metal framed windows This is because the heat from the heatgun is
5. 19410 10 1992819 42818 AI8381 01 jou 191910 1 151 9 Xy 9 021504 91618 10 sem unbjeay Jajeap ay Jo ssaJppy jo add aui PYM e se unbyeay noA sen uMO 4968 9 14 18 1 10601894 MIB seM 19945 pue JO 8snoH I6M sem Jajeap ay Jo ssaJppy aseyoind 1104 jo 9160 15 3 00 5 31 pm 15 CD700 1600 1683 UK 01 16 GUARANTEE CARD FOR THE UK IRELAND AND SOUTH AFRICA South Africa Black amp Decker South Africa Pty Ltd Suite no 107 PostNet X65 Halfway House 1685 United Kingdom amp Ireland PO Box 821 Slough Berkshire SL1 3AR Please complete this section immediately after the purchase of your heatgun and post it to the Black 8 Decker address in your country above Part no 373340 37 10 99 1 15 3 00 5 31 pm 16 CD700 1600 1683 UK p01 16
6. 700 KX1600 1683 UK p01 16 4 15 3 00 5 31 pm CD700 1600 1683 UK 01 16 5 buildings may have been painted in the past with paint containing lead and covered by additional layers of paint Once deposited on surfaces hand to mouth contact can result in the ingestion of lead Exposures to even low levels of lead can cause irreversible brain and nervous system damage young and unborn children are particularly vulnerable Do not smoke eat or drink in a work area that could or may be contaminated by lead Lead based paints should only be removed by a professional and should not be removed using a heatgun When removing paints you should ensure that your work area is enclosed It is advisable to wear a dust mask Do not burn the paint Use the integral scraper where supplied otherwise keep the nozzle at least 25mm 1 from the surface as this keeps the temperature below the required 450 C If you are scraping from a vertical position then you should scrape downwards to prevent the paint from falling back into the heatgun and burning Dispose of all paint debris safely and ensure that the work area is thoroughly cleaned after completing the job Do not use in a damp atmosphere or where flammable gases may be present or use near combustible materials Spaces behind boards ceilings and floors and wall cavities in timber frame constructed houses can contain flammable materials Check before using
7. Ltd Spennymoor County Durham DL16 6JG United Kingdom The Black amp Decker policy is one of continuous improvement to our product and as such we reserve the right to change the product specification without prior notice CD700 KX1600 1683 UK p01 16 9 I ENGLISH 15 3 00 5 31 pm BLACKS DECKER E11969 373032 CD700 KX1600 1683 UK p01 16 10 15 3 00 5 31 pm 1 II BLACKS DECKER 11963 371170 02 15 3 00 5 31 CD700 1600 1683 UK 01 16 1111 WD 74 49 BLACKS DECKER 15 3 00 5 31 pm CD700 KX1600 1683 UK p01 16 CD700 1600 1683 UK 01 16 13 15 3 00 5 31 Australia DeWalt Industrial Power Tool Company Tel 03 9895 9200 Distributors of Black amp Decker products Fax 03 9899 7465 7 Clarice Road Box Hill Victoria 3128 New Zealand Black amp Decker 09 579 7600 483 Great South Road Fax 09 579 8200 Penrose Auckland South Africa Black amp Decker South Africa Pty Ltd Tel 011314 4431 Suite no 107 PostNet X65 Fax 011 314 4435 Halfway House 1685 United Kingdom Black amp Decker Tel 01753 574277 210 Bath Road Slough Tlx 848317 BAND MH Berkshire 511 Fax 01753 551155 Part no 373340 37 10 99 1 CD700 KX1600 1683 UK p01 16 14 15 3 00 5 31 pm saiueduioo
8. ee to either replace all defective parts or at our discretion replace the unit free of charge provided that The productis returned to us or our authorised repairers with evidence of date of purchase The product has not been used for trade professional or hire purposes The product has not been subjected to misuse or neglect The product has not sustained any damage through foreign objects substances or accidents e III Repairs have been attempted by anyone other than our authorised repair distributors This guarantee is offered as an extra benefit and is additional to the customers statutory rights AFTER SALES SERVICE FOR YOUR BLACK amp DECKER PRODUCT UK AUSTRALIA AND NEW ZEALAND ONLY Black amp Decker offers a nationwide network of authorised service agents The use of other than genuine Black amp Decker accessories and parts may damage or reduce the performance of your Black amp Decker product and may also endanger the user The terms and conditions of the warranty may also be effected OUR AFTER SALES SERVICE POLICY UK AUSTRALIA AND NEW ZEALAND ONLY It is our aim that all Black amp Decker customers should be totally satisfied with their Black amp Decker product and after sales service but if help or advice is needed please contact your local Black amp Decker authorised repair agent who will be happy to help Full details of our after sales service and a list of these agent
9. ely or it will harden again OTHER USES FOR YOUR HEATGUN On low heat KX1682 KX1683 Drying paint and varnish Removing stickers and decorations 15 3 00 5 31 pm Waxing and dewaxing eg ski s Drying wet timber prior to filling Shrinking PVC wrapping and insulation tubes Thawing frozen pipes On medium heat KX1683 Welding plastics Bending plastic pipes and sheets Loosening rusted or tightly fastened nuts and metal screws On high heat CD700 KX1600 KX1682 KX1683 Removal of paints and lacquers Starting barbecues Soldering plumbing joints ACCESSORIES 9883 Glass protector 9884 Spoon reflector A9887 Cone nozzle 9881 Fish tail A9890 Kit which includes all of the above CLEANING Use only mild soap and a slightly damp cloth to clean your heatgun Many household cleaners contain chemicals which could seriously damage the plastic Also do not use petrol turpentine lacquer or paint thinners or similar products Never let any liquid get inside the tool and never immerse any part of the tool into liquid EC DECLARATION OF CONFORMITY We declare that units CD700 KX1600 KX1682 KX1683 conform to 89 392 EEC 89 336 EEC EN55014 73 23 EN60555 EN55104 EN60355 EN61000 A weighted sound pressure 68dB A A weighted sound power 81dB A Hand arm weighted vibration 2 5m s Brian Cooke Director of Engineering Black amp Decker
10. ible electrical insulation failure within the tool ELECTRICAL SAFETY Be sure the supply is the same as the voltage given on the rating plate The tool is fitted with a two core cable and plug MAINS PLUG REPLACEMENT UK ONLY Should the mains plug need replacing and you are competent to do this proceed as instructed below If you are in doubt contact a Black amp Decker service agent or a qualified electrician Disconnect plug from the power supply Cut off the plug and dispose of safely A plug with bared copper conductors is very dangerous if engaged in a live socket outlet Only fit BS1363A approved plugs fitted with the correctly rated fuse Note Fuses do not give personal protection against electric shock The cable wire colours or a letter will be marked at the connection point of most good quality plugs Attach the wires to their respective points in the plug see diagram Brown is L live and blue is N neutral Fit a BS1363A Pita 13 amp fuse approved approved resilient plug to BS1362 Connect Connect blue to brown to N neutral L live Make sure that the outer sheath of the cable is held firmly by the clamp 0 H 230 volts AC only 3 Never use a light socket 15 3 00 5 31 pm CD700 KX1600 1683 UK p01 16 6 ENGLISH Before replacing the top cover of the plug ensure thatthe cable restraint is holding the outer sheath of the cable firmly and that the t
11. nd safer performance basic safety precautions should always be taken to Follow the instructions for lubricating and changing reduce the risk of fire electric shock and personal accessories Inspect the tools cord periodically and injury Read all these instructions before attempting to if damaged have repaired by an authorised service operate the product and save this booklet For safe operation Keep the work area clean Cluttered areas and benches invite injuries Consider the work area environment Do not expose the power tool to rain and do not use in damp or wet locations Keep the work area well lit Do not use the power tool where there is a risk to cause fire or explosion Guard against electric shock Avoid body contact where possible with earthed or grounded surfaces e g pipes radiators ranges and refrigerators Keep children away Do not let visitors touch the tool or extension cord All visitors should be kept away from the work area Store idle tools When not in use tools should be stored in a dry high or locked place out of reach of children Do not force the tool It will do the job better and more safely atthe rate for which it was intended Use the right tool Do not force small tools or attachments to do the job of a heavy duty tool Do not use the tool for purposes not intended for example do not use a circular saw to cut tree limbs or logs Dress properly Do not wear loose clothing or jewellery
12. r heatgun on push the orange switch HANDLING YOUR HEATGUN Do not place your hand over the air vents or block these vents in any way This restricts the airflow through the element and causes over heat ing Your heatgun is designed for one handed use 2 forward to the 1 2 3 position position 3 is on KX1683 only The position numbers representthe heat numbers described in the table above To switch your heatgun off pull the orange switch back to reveal the off 0 position CD700 KX1600 only To switch your heatgun on press the rocker switch to depress the I position To switch your heatgun off press the rocker switch to depress the 0 position Note Allow the element to heat up for a few seconds before use Initially some smoke may emit from your heatgun This is normal and will soon cease COOLING DOWN In use the nozzle of your heatgun becomes extremely hot Great care is necessary when cooling your heatgun after use KX1682 KX1683 only To speed up the cooling time set the orange switch to heat setting 1 for a few minutes before switching your heatgun off Only after switching off suspend your heatgun on the handing ring 5 or stand the tool as in Hands free use Leave to cool for at least 30 minutes KX1682 KX1683 only A rollover feature prevents your heatgun being placed
13. rther use of the tool a guard or other partthat is damaged should be carefully checked to determine whether it will operate properly and perform its intended function Check for alignment of moving parts free running of moving parts breakage of parts mounting and any other conditions that may affect its operation A guard or other part that is damaged should be properly repaired or replaced by an authorised service agent unless otherwise indicated in the product booklet Have defective switches replaced by an authorised service agent Do not use the tool if the switch does not turn it on and off Warning The use of any accessory or attachment other than recommended in the product booklet may present a risk of personal injury Have the tool repaired by a qualified person The electrical tool is in accordance with the relevant safety requirements Repairs should only be carried out by qualified persons using original spare parts otherwise this may result in considerable danger to the user ADDITIONAL SAFETY INSTRUCTIONS FOR HEATGUNS Always switch off before putting tool down Extreme care should be taken when stripping paint the peelings residue and vapours of paint may contain lead which is poisonous Any pre 1960 Secure the work Use clamps or a vice to hold the work It is safer than using a hand and it frees both hands to operate the tool Do overreach Keep proper footing and balance at all times CD
14. s can be found on the Internet at www 2helpU com Alternatively call our Service and Information Centre whose number you will find towards the back of this manual ACCESSORIES The performance of any power tool is dependant upon the accessory used Black amp Decker accessories are engineered to high quality standards and are designed to enhance the performance of your tool Buying a Black amp Decker accessory will ensure that you get the very best from your Black amp Decker tool TECHNICAL DATA The level of sound pressure of the tool is in accordance with EEC legislation It is recommended that you take appropriate measures for the protection of your hearing if the sound level seems uncomfortable This normally equates to a sound pressure in excess of 85dB CD700 KX1600 KX1682 KX1683 Power 1400W 1400W 1600W 1600W Cable length 2m 3m 3m 3m Switch position 550 550 C 1400 140 C Switch position2 560 C 380 C Switch position3 560 C Note This user manual also covers more than one catalogue number within this product group Refer to your carton for details of your product Your product includes some or all of these features 15 3 00 5 31 pm 1 8128 CD700 1600 1683 UK 01 16 7 FEATURES On off heat setting switch Air inlet holes Stands Hanging ring ENGLISH OPERATING YOUR HEATGUN KX1682 KX1683 only To turn you
15. the heatgun Allow the tool to cool fully before storing Ensure adequate ventilation when using heatguns as toxic fumes may be produced Do not use hairdryer The air temperature is far higher than a hairdryer Do not obstruct either the air intake or nozzle outlet as this may cause excessive heat build up resulting in damage to the tool Do not direct the hot air blast at other people Do not touch the metal nozzle as it gets very hot during use and remains hot for up to 30 minutes after use Do not place the nozzle against anything while using or immediately after use Do not poke anything down the nozzle as it could give you an electric shock Do not look down the nozzle while the unit is working because of the high temperatures being produced Do not allow paint to adhere to the nozzle or scraper as it could ignite after a time Do not operate your heatgun whilst it is hanging by the hanging ring Save these instructions ENGLISH The tool is double insulated This means that all the external metal parts are electrically insulated from the mains power supply This is done by placing insulation barriers between the electrical and mechanical components making it unnecessary for the tool to be earthed Note Double insulation does not take the place of normal safety precautions when operating the tool The insulation system is for added protection against injury resulting from a poss
16. wo leads are correctly fixed atthe terminal screws If the fuse cover is missing or damaged do not use the plug For replacement or detachable fuse covers contact a Black amp Decker service agent Warning Never connect live or neutral wires to the earth pin marked E or MAINS PLUG REPLACEMENT AUSTRALIA AND NEW ZEALAND ONLY Should the mains plug or cordset of the product be damaged it must only be replaced by an authorised Black amp Decker service agent because special purpose tools are required EXTENSION CABLES Up to 30m 100ft of 3 core extension cable can be used without undue loss of power Note An extension cable should not be used unless absolutely necessary Use of an improper extension cable could result in a risk of fire and electric shock If an extension cable must be used make sure it is properly wired contains the correct rated fuse as recommended in its literature and is in good electrical condition UNWANTED TOOLS AND THE ENVIRONMENT Should you find day that the tool needs replacement or is of no further use think of the protection of the environment Black amp Decker service agents will accept old tools and will dispose of them in an environmentally safe way THE BLACK amp DECKER GUARANTEE UK AUSTRALIA AND NEW ZEALAND ONLY If the Black amp Decker product becomes defective due to faulty materials and workmanship within 24 months from the date of purchase we guarant
Download Pdf Manuals
Related Search