Palm Sander User Manual
Contents
1. KRAFTtech OWNER S MANUAL Model Number PS160CA 3 1 4 Sheet Palm Sander Registration Card Inside A CAUTION To reduce the risk of fire electric shock and personal injury read and understand the owner s manual before operating this product Save this manual TABLE OF CONTENTS SECTION PAGE Warranty 2 Introduction 2 General safety rules for all power tools 3 Specific safety rules for palm sander 5 Technical specifications 6 Functional description 6 Assembly 7 Operation instructions 8 Maintenance 10 Accessories 10 WARRANTY FULL 2 YEAR WARRANTY ON THIS KRAFTtech 1 4 SHEET PALM SANDER TOLL FREE NUMBER 1 866 513 6723 If this KRAFTtech Power Tool is found to be defective in materials or workmanship within 2 years from the date of purchase the manufacturer will replace the product free of charge Warranty replacement service is available by returning tool with the original sales receipt showing date of purchase Call our toll free number or visit www krafttechpowertools com for more information This warranty does not include damages or defects caused by or resulting from abuse accidents alterations or commercial use This KRAFTtech product is warranted for home domestic use only This warranty does give you specific legal rights and you may also have other rights which may vary from state to state For Repair Replacement Parts call our toll free number INTRODUC2. TION This Palm Sander is designed to give an exceptional finish on wood surfaces and speed stock removal It will also remove lacquer varnish and other coated finishes It can sand flush against all three sides of the tool and fit into tight places It has many features that will make your job faster easier and more convenient Safety per formance and dependability have been given top priority in the design of this tool as well as making it easy to maintain and operate A WARNING Carefully read through the entire manual before attempting to use this tool Be sure to pay special attention to the safety rules and all the Warnings and Cautions throughout this manual WARNING Read and understand all instructions Failure to follow all instruc tions listed below may result in electric shock fire and or serious personal injury SAVE THESE INSTRUCTIONS KRAFTtech PS160CA 3 Page 2 GENERAL SAFETY RULES ELECTRICAL SAFETY Double insulated tools are eguipped with a polarized plug FIG 1 X one blade is wider than the other This plug will fit in a po S larized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a quali fied electrician to install a polarized outlet Do not change the plug in any way Double insulation eliminates the need for the three wire grounded power cord and grounded power supply system See FIG 1 FOR SAFE OPERATION Gonside
3. cause shock burns or electrocution Check damaged parts Before further use of the tool a guard or any other part of the tool that is damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment of moving parts free running of moving parts breakage of parts mounting and any other conditions that may affect its operation A guard or other part that is damaged should be properly repaired or replaced by an autho rized service center unless otherwise indicated in this instruction manual Have defective switches replaced by an authorized service facility Do not use the tool if the switch does not turn it on and off A WARNING The use of any accessory or attachment other than those recom mended in this instruction manual may present a risk of personal injury Have your tool repaired by a gualified person This electric tool has been designed in ac cordance with the relevant safety standards Repairs should only be carried out by a guali fied person using original replacement parts Failure to do so not only will void the warranty but could result in injury to the user or other participants in the work area KRAFTtech PS160CA 3 Page 4 SPECIFIC SAFETY RULES Always wear safety goggles and a dust mask when sanding especially when sanding overhead A suitable breathing respirator must be worn while sanding chemically pressuretreated surfaces This KRAFTtech san
4. cluded with your KRarrtech sander After attaching the sandpaper to the palm sander align the sandpaper with the punch and push down on the sandpaper until the punch has pierced the sandpaper The sandpaper is now ready to use with the dust collection system on your sander See FIG 5 FIG 5 ROCKER ON OFF SWITCH To turn the tool ON or OFF push in the switch rocker to the left or right side of the tool Be sure sander is ON and at full speed before beginning sanding operation Remove the tool from the work surface before turning OFF SANDING Do not place excessive pressure on the sander Excessive pressure on the sander may result in an uneven sanding job and can also cause overheating and possible damage to the motor Do not leave the tool sanding in one spot for an extended time otherwise uneven sanding will result KRAFTtech PS160CA 3 Page 9 MAINTENANCE A WARNING A repair or replacement of this tool must be performed by a quali fied service technician For information call our toll free number at 1 866 513 6723 A WARNING Always use only a soft dry cloth to clean your sander never use any detergent or alcohol Disconnect the plug from the power source before cleaning 4A CAUTION No chemical agents are approved for use in cleaning this power tool Clean with a dry cloth or towel only OANODADOCG nas a sa zidane Had oui tau ii lod caer 6pcs USE Ba Quickies too zaa s
5. der is not suitable for wet sanding Using this tool for this purpose could cause electric shock Do not use sandpaper that is larger than needed Extra paper that extends beyond the sanding pad can cause serious lacerations This KRAFTtech sander is equipped with a dust extraction port Dust from the sanding operation can be removed by attaching either a shop vacuum hose or the dust collection bag included with the tool When using the collection bag be sure to empty it frequently Never discard sanding dust in the area of or on an open flame as these fine wood particles can be highly combustible Use of damaged cords can shock burn or electrocute TECHNICAL SPECIFICATIONS Model PSIGOCAS Sandpaper 1 4 sheet V Volts Alternating Current KRAFTtech PS160CA 3 Page 5 FUNCTIONAL DESCRIPTION 1 Rocker On Off Switch with Dust Guard 2 Sandpaper Clamp 3 Clamp Lever 4 Pad 5 Vents 6 Cord 7 Dust Collection Bag 8 Sandpaper Punch FIG 2 ASSEMBLY A WARNING Always disconnect the plug from the power source before attach ing or removing sandpaper The sandpaper must be drawn as tight as possible across the pad of the sander for efficient sanding as a loose sandpaper can slip on the work surface ATTACHING SANDPAPER 1 To open clamp push down clamp lever as shown in FIG 3 2 Place the sandpaper grit side up between the clamp and base plate while aligning edges of th
6. e cord or yank the cord to disconnect it from the socket Keep the cord away from heat oil and sharp edges Secure your work Use clamps or a vice to hold the work It is safer than using your hand and it frees both hands to operate the tool Do not overreach Keep proper footing and balance at all times KRAFTtech PS160CA 3 Page 3 GENERAL SAFETY RULES Maintain tool with care Keep cutting tools sharp and clean for better and safer perfor mance Follow instructions for lubrication and changing accessories Inspect tool cord periodically and if damaged have it repaired by an authorized service facility Inspect extension cords periodically and replace if damaged Keep handles dry clean and free from 0il and grease Disconnect tools Always unplug the tool when it is not in use before servicing and when changing accessories such as blades bits and cutters Remove adjusting keys and wrenches Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning it on Avoid unintentional starting Do not carry a plugged in tool with a finger on the switch Make sure the switch is off when plugging tool in Use outdoor extension cords When tool is used outdoors use only extension cords intended for outdoor use Stay alert Watch what you are doing Use common sense Do not operate the tool when you are tired Replace damaged cords immediately Use of damaged cords can
7. e sandpaper with either edge of the pad Pre bending the sandpaper makes attachment easier KRAFTtech PS160CA 3 Page 6 ASSEMBLY 3 After inserting the sandpaper release pressure on clamp lever making sure that the clamp is gripping the sandpaper and the sandpaper is aligned with the pad 4 Wrap the sandpaper around the bottom of the pad and attach the free end of sandpaper under the opposite clamp repeating procedures 1 2 amp 3 above FIG 3 GLAMP LEVER PAD SANDPAPER KRAFTtech PS160CA 3 Page 7 ASSEMBLY ATTACHING THE DUST BAG Align the groove in the dust bag assembly with the groove in the vacuum port see FIG 4 and then press down on the dust bag assembly to lock it in place FIG 4 BS 12 OPERATION INSTRUCTIONS SANDPAPER This 1 4 sheet sander is designed to be used with standard commercially available sandpa per sheets Cut the sheet crosswise into quarters for a precise fit Aluminum oxide silicon carbide or other synthetic abrasives are recommended for power sanding use For rough sanding sandpaper with a coarse grit is best For smoothing or final sanding sandpaper with a fine or extra fine grit should be used KRAFTtech PS160CA 3 Page 8 OPERATION INSTRUCTIONS SANDPAPER PUNCH To remove dust effectively from the work surface the 1 4 sheet of sandpaper must have holes punched through the surface A sandpaper punch is in
8. nes dw KO atv O kw Ukrajin 1pc sandpaper PUNCI wa wasza ads ved AAA AA EWA k bud PA 1pc 4A WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm Some examples of these chemicals are Lead from lead based paints Crystaline silica from bricks and cement and other masonry products Arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety eguipment such as those dust masks that are spe cially designed to filter out microscopic particles KRAFTtech PS160CA 3 Page 10 KRAFTtech PS160CA 3 Page 11
9. r the work area environment Keep your area clean and well lit Cluttered benches and dark areas invite accidents Do not expose power tools to rain Do not use power tools in damp or wet locations Do not use power tools where there is risk of fire or explosion Guard against electric shock Avoid contact with grounded surfaces such as pipes radia tors ranges and refrigerators Keep children away Do not let visitors touch the tool or extension cord All visitors should be kept away from work area Store idle tools When not in use tools should be stored in a high or locked up place that is dry and out of the reach of children Do not force the tool It will do the job better and safer if used in a manner for which it was intended Use the right tool Do not force small tools or attachments to do the job of a heavy duty tool Do not use tools for purposes not intended for example do not use circular saws to cut tree limbs or logs Dress properly Do not wear loose clothing or jewelry as they can be caught in moving parts Rubber gloves and nonskid footwear are recommended when working outdoors Wear a hair net to contain long hair Use safety glasses Also use a face or dust mask if the cutting operation is dusty Connect dust extraction equipment If devices are provided for the connection of dust extraction and collection take measures to ensure these are connected and properly used Do not abuse the cord Never carry the tool by th
Download Pdf Manuals
Related Search