9448 user guide 496237 iss 4.P65
Contents
1. be any four digit code you choose EXCEPT 0000 Followed od by The 0000 user code is inactive and will not operate the A 4 Gir cone Code to be se Changed system To activate the second user code change the 0000 to another four digit number To inactivate the Two Bleeps f from second user code again change it back to 0000 Sounder The New Fe Four Digit ell Code Two Bleeps from Sounder DO NOT use the same number for both user codes Note The control unit does not use the 6 light on the keypad Also ignore the symbol over the 9 key it has PA N E L no function on your system Zone Descriptions Entry Exit Zone Sc Scantronic Day Tel Leading the way in security Night Tel Part No 496237 Issue 42. Enter via Go to designated control panel route 0 900 Interrupted Exit Tone 0900 Investigate cause and restart setting sequence Zone x Repeat for each zone Zone o No 0 900 TO FULL SET Key in your four digit user code shown as at left The exit tone starts Leave premises via the designated exit door Exit tone stops after preset time Your alarm system is SET TO PART SET Your alarm system may have been installed to allow you to have part of the premises set while other area s are off To part set the system press 2 then 41 followed by your user code Note that the part set exit tone is usually a buzzer sound but your system may be programmed to silent set Note If you enter your user code incorrectly four times in a row then the system will raise a tamper alarm See opposite TO SWITCH OFF Full Set Enter by the designated entry door Entry tone starts Go to control panel Key in your user code System is OFF Part Set Go to control panel Entry tone starts Key in your user code System is OFF Note The system has a preset entry time to allow you to get to the panel When the entry time has elapsed your system may be programmed to give an intemal alarm for 30 sec onds At the end of this 30 seconds the system gives a full alarm external sounder Key in youruser code to cancel the alarm IF A ZONE LIGHT GLOWS WHILE SETTING If during setting the sounder gives an int
3. e The internal sounders will operate for three seconds and then the external sounder and strobe will operate for three seconds TO WALK TEST Key in 5 then 4 followed by your user code The internal sounder gives a steady tone Open and close the Exit Entry zone and zones 1 to 4 Open and close zone 5 if it is NOT a fire zone and zone 6 if it is NOT a panic button Each time you open a zone the internal sounder gives a pulsing tone You cannot test the Tamper Circuits without creating an alarm condition Similarly a panic button will always cause a full alarm To stop walk test key in your access code TO READ THE LOG 8 The system keeps a log of the last ten alarm or tamper events To read the log key in 8 then 4 followed by your user code The system switches on the zone or Tamper lights to show you the most recent event If you want to K dsh t see earlier events then press lt lt the 1 key To see eypad s ne recent more recent events press gt gt the 3 key The keypad gives a short tone when you reach either end of the log Earlier events To leave the log press OMIT or 4 U S E R G U D E Later events pan TO CHANGE YOUR USER CODE 6 amp Your system provides two separate four digit user codes When the system is new the user codes are 1234 and 0000 Change the 1234 user code immediately to a Cois Existing Cod seeds No number that only you know The new code can
4. e chime zones operate Note that the Installer must program your chime zones KEYPAD PA Your system may be programmed to allow you to start a Panic Alarm from the keypad ask you Installer If so then press keys 1 and 3 together to start a Panic Alarm AFTER AN ALARM To switch the bells off Key in your user code The sounders will stop and the zone light s for the detectors that triggered the alarm will glow Reset system You must reset the system before it can be used again Key in your access code again All the zone lights should go off The system is now ready for use Fire Alarm The fire alarm is a two tone siren note from the internal sounder Leave the building immediately and call the Fire Brigade Do not go back into the building until it is safe to do so Switch the alarm off and reset the system as described above If you have trouble resetting the system make sure that the fire detector is not being triggered Tamper or Panic Alarm If you hear the internal sounder when the system is off then look at the control panel If the Tamper light glows then key in your user code to stop the sounder Call your alarm installer for service If the Panic light zone 6 glows then deal with the cause of the alarm first Next reset the panic button then switch the alarm system bells off and reset the system see above TO TEST BELLS Make sure system is unset before starting the test Key in 4 then followed by your user cod
5. errupted tone and a zone light glows then a detector is being triggered maybe a door or window is open Key in your user code to stop the tone Check the indicated zone s and if possible correct the cause of the alarm Try setting the system again If the fault persists call your alarm installer If the Entry Exit light glows the exit door may be open Leave the premises and close the door The interrupted tone should change to a steady tone when the door is closed and the system then sets as normal TO OMIT A DETECTOR You may need to temporarily set the system with one or more detectors omitted Key in the zone number followed by OMIT for all the zones you want to omit and then key in your user code The system flashes the light s of the omitted zone s during the exit time and then sets Note that you cannot omit a panic or fire zone or the EE zone The system will not raise an alarm if any omitted detector is triggered during this setting cycle The system will reinstate the detector s and set normally the next time you set the system D oO PE 8000 oo 8 Enter Go To Control Building Panel o 0 0 0 Zone Tamper Panic Reset any panic buttons activated then 3 90 0 0 A lt lt 8000 qu 8000 Trigger Detectors Not Panic Alarm 000o TO SWITCH CHIME ON OR OFF Key in 7 then 4 followed by your user code to switch Chime on or off When Chime is on the internal sounder chimes when th
Download Pdf Manuals
Related Search